INSTRUCTION SHEET KIT CONVERSION, PELLET ICE, HEX, FOR THE IBD30 AND FS30 DISPENSERS - INSTALLATION INSTRUCTIONS IMPORTANT: BEFORE BEGINNING THIS PROCEDURE, IT WILL BE NECESSARY TO DISCONNECT ELECTRICAL POWER, WATER AND DRAINS TO THE ICE MAKER. IBD30 Unit Figure a FS30 Unit Figure b CATCH KNOBS. INSTALLATION INSTRUCTIONS FS30 Unit Figure 2 Figure 3. Remove Merchandiser by lifting and pulling back (see Figures a and b)..2 FOR FS30 UNITS ONLY A. Unlatch Reflector Assembly by pulling the two (2) catch knobs toward center of unit and then swing assembly up (see Figures 2 and 3). Continue lifting assembly until it locks in place (see Figure 4). B. Turn off power to Reflector Assembly by pressing Breaker Switch on Power Supply (see Figure 5). Note that the power is OFF when a white line is showing (see Figures 6 and 7). Figure 4 Figure 5 6655 LANCER BLVD. SAN ANTONIO, TEXAS 7829 USA (20) 30-7000 FAX SALES NORTH AMERICA 20-30-7245 INTERNATIONAL SALES 20-30-7242 CUSTOMER SERVICE 20-30-7242 LATIN AMERICA 20-30-7245 EUROPE 32-2-755-2399 PACIFIC 6-8-8268-978 FAX ENGINEERING: 20-30-7096 "Lancer" is the registered trademark of Lancer Copyright 2006 by Lancer, all rights reserved DATE: 03/0/06 P.N. 28-0700
ON OFF Figure 6 Figure 7.3 Remove Icemaker, Adapter Plate (if applicable, see Figure 8), and Bin Stat from the top of the dispenser. NOTE: See icemaker manufacturer s instructions for ice maker removal..4 Remove all ice from ice bin (see Figure 9). ICE MAKER LIFT GASKET UP HERE Figure 8 ADAPTER PLATE View Looking down Ice Maker and Ice Removed Figure 9.5 Remove the Agitator Pin Clip and Pin (see Figure 0)..6 Remove the Cube Agitator Bar. A. Push the agitator towards the rear of machine to disengage it from the wheel. B. Pull the agitator to the side to clear the wheel hub (see Figure ). C. Pull the agitator towards the front of the machine to disengage from the back bearing. AGITATOR AGITATOR PIN Figure 0 2 Figure
Figure 2 Figure 3.7 Remove the Cube Dispensing Wheel (see Figure 2)..8 Remove Ice Shroud (see Figure 3). Figure 4 Figure 5.9 The base unit is now ready for the Nugget Kit Installation (see Figure 4)..0 Install Extension Assembly (see Figure 5). NOTE: Section.0 above is applicable to FS-30 dispensers.. Remove Gasket (see Figure 6)..2 Insert Ice Shroud into the ice bin (see Figure 7). Figure 6 Figure 7 3
Figure 8 Ice Chute opening in the ice bin Figure 9.3 Seat Ice Shroud into the ice bin (see Figure 8). A. Push the Ice Shroud back towards rear wall such that the ice chute clears the top wall of the ice bin. B. Push the Ice Shroud into the ice bin ensuring that the ice chute fits into the ice chute opening in the ice bin (see Figure 9). Figure 20 Figure 2.4 Install the Nugget Dispensing Wheel (see Figure 20)..5 Install the Nugget Agitator Assembly (see Figure 2). A. Begin by inserting the end of the Agitator into the Bearing on the back wall. B. Push Agitator towards rear to allow clearance between the Agitator and Wheel Hub and align agitator with Wheel Hub. C. Fit the Agitator to the Wheel Hub. Figure 22 Figure 23.6 Reinstall the Agitator Pin (see Figure 22)..7 Reinstall the Agitator Clip (see Figure 23). 4
Figure 24 Figure 25.8 Install the Shield (see Figure 24). A. Hold shield so that the hooks are facing the front of the machine. B. Slide the Shield into the Ice Shroud ensuring that the Shield is captured between the Ice Shroud and the Ice Bin at the top left and right corners (see Figure 25). NOTE: Figure 25 shows a detailed view of the Shield being captured between the Ice Shroud and the Ice Bin C. Also ensure that the Tab at the bottom of the Shield aligns with the Slot at the bottom of the Ice Shroud and fully seats (see Figure 26 and Figure 27). Tab Tab Fully Seated Slot.9 Reinstall gasket (see Figure 28). Figure 26 Figure 27.20 Install the front block of the Extension Assembly. A. Hook the hooked side of the front block under the main extension (see Figure 29). B. The front block shoud fit flush with the main extension (see Figure 30). Figure 28 Figure 29 Figure 30 5
.2 Component installation complete..22 Install the adapter plate to support the Ice machine. NOTE: There is a sticker on top of the adapter plate that indicates which side is to point front based on the Ice Maker to install (see Figure 32)..23 Reinstall Bin Stat..24 Reinstall Merchandiser..25 Reinstall the Ice maker. Installation complete Figure 3 SERIES 4500 / IBD30 AND THE FS30 PELLET ICE ASSEMBLY / PARTS LISTING IBD30 FS30 ITEM PART NO. CCP PART NO. DESCRIPTION QTY X X 02-0577 N/A Grommet, Rubber, G3002 X X 2 03-0368 068570 Retainer, Pin, Agitator, IBD X X 3 05-2293/0 0654 Ice Shroud, IC X X 4 23-40 09543 Agitator Assy, Helical, IC, HEX X 5 23-363 07964 Extension Assy, 4 /2, IBD30 X X 6 42-009 N/A Foamed Cover, Scots/Hoshi, Pellet Ice X X 7 30-9446 3764 Adapter, Mech Bin-Stat, Scots X X 8 82-3538 0652 Ice Chute Assy, IBD30, Pellet Ice X X 9 82-365 09523 Dispensing Wheel Assy, Pellet Ice, HEX X X 0 30-9880 0655 Shield, Nugget Ice, One Piece with Tab X 30-8832/0 N/A Bracket, Valve Plate, FS30 3 NOTICE: The Pellet Ice components listed on this Instruction Sheet are to be used ONLY in conjunction with Nugget, Cubelet, or Chewblet ice. LANCER makes no warranty of any kind with regard to these components being used with any other kind of ice. Lancer Kit Part Number 82-349* is available in order to support the functionality of Lancer s FS30 and IBD30 Dispensers. Kit 82-349* contains the top cover assembly (Lancer PN 42-009). THIS COVER CAN BE USED WITH EITHER A SCOTSMAN OR HOSHIZAKI PELLET ICE MACHINE. Labels are affixed to the top of this cover indicating the proper orientation for each machine (see Figure 32). *CCP Part Number 0787 An X in the left columns indicates the parts used in the installation for an IBD30 Dispenser or an FS30 Dispenser. 6
LABEL FOR HOSHIZAKI ICE MAKER (TO FRONT OF DISPENSER) 6 (FOAMED TOP COVER ASSEMBLY) LABEL FOR SCOTSMAN ICE MAKER (TO FRONT OF DISPENSER) ATTACH HERE FOR SCOTSMAN 2 ATTACH HERE FOR HOSHIZAKI 7 ADAPTER, MECHANICAL BIN STAT 5 0 4 9 3 8 Figure 32 7
NOTES Please refer to the Lancer web site (www.lancercorp.com) for information relating to Lancer Installation and Service Manuals, Instruction Sheets, Technical Bulletins, Service Bulletins, etc. 8