1 Technical Specifications PSE - SERIES REV-B Electric Heating / Electric Cooling CONFORMS TO ANSI/UL STD. 1995, CERTIFIED TO CAN/CSA STD. C22.2 NO. 236 AND ANSI/AHRI STD. 390 Self contained, high efficiency Thru-The-Wall heating & cooling unit Heating - 5 kw, 7.5 kw, kw, 15 kw Cooling - 12800 Btuh, 16500 Btuh, 19500 Btuh, 24400 Btuh FEATURES COMPATIBLE BOX SIZE Industry standard footprint for retrofit applications Appliance shell dimensions: 43-1/8 High x 28 Wide x 32 Deep Wall Sleeve dimensions where penetrating exterior wall: 44-7/8 High x 28-7/8 Wide Standard TAUPE color Custom color options are available FEATURES HEATING MODULE Up to 15kW Electric Resistance Heating Up to 24400 Btuh Cooling Up to.8 EER with R-4A Refrigerant Micro-Channel Condenser and Evaporator Coils High efficiency compressor Pre-wired and pre-charged Removable heating and cooling module Plug-and-play installation and service Individual metering and control for each unit One Piece motorized Condenser Fan design CIRCULATION BLOWER Dual Inlet Blower for higher flow rates / reduced air noise Endura Pro Multi-Speed Electronically Commutated Motor for increased electrical efficiency SERVICE ADVANTAGES Indoor access to all parts & maintenance needs Innovative, dual slide-out chassis can be partially or fully removed for efficient servicing. MODULE With spare modules, building management can perform quick swap outs, maintaining indoor conditions in the apartment/condo, while troubleshooting non functioning units off line. Can perform direct replacement of the individual modules at the end of their service life instead of replacement of the complete appliance. All control harnesses are separated with modular quick disconnects so module swap outs do not require time consuming rewiring. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 w w w. n a p o l e o n h e a t i n g a n d c o o l i n g. c o m
2 NOMENCLATURE P S BRAND MODEL C A 040 HEAT TYPE HEAT CAPACITY TYPE 018 CAPACITY P=Condo Pack A REVISION A, B, C... S=Single Packaged Vertical R=Roof Top P=Packaged Residential Air Conditioning 000 - Blower Only 012-12 000 Btu/h / 1.0 Ton 018-18 000 Btu/h / 1.5 Ton 024-24 000 Btu/h / 2.0 Ton 030-30 000 Btu/h / 2.5 Ton C - Gas Condensing S - Gas Standard E - Electrical H - Hydronic D - Duct only (No heat) i.e. PSD000A012A G a s C o n d e n s i n g Gas Standard(80%) Heat designation Heat designation 000 - Duct Only 000 - Duct Only 015-15 000 Btu/h 026-26 000 Btu/h 030-30 000 Btu/h 038-38 000 Btu/h 040-40 000 Btu/h 051-51 000 Btu/h 050-50 000 Btu/h 064-64 000 Btu/h E l e c t r i c H eat H yd ro n i c H e at Heat designation Heat designation 000 - Duct Only 000 - Duct Only 005-5.0 kw 030-30 000 Btu/h 007-7.5 kw 042-42 000 Btu/h 0 - kw 015-15 kw A - Air Conditioning - std. eff. Rev A B - Air Conditioning - std. eff. Rev B C - Air Conditioning - high eff. H - Heat Pump - std. eff. P - Heat Pump - high eff. F - Blower Only (No Cool) i.e. PSC040F000A Example: PSC040B018A - Condo Pack - Single Packaged Vertical - Condensing Gas heating 40k Btu/h - Rev B AC 1.5 ton - Rev A SPECIFICATIONS PERFORMANCE TABLE 1. Model No. PSE005B012A PSE005B018A PSE005B024A PSE005B030A PSE007B012A PSE007B018A PSE007B024A PSE007B030A PSE0B012A PSE0B018A PSE0B024A PSE0B030A PSE015B012A PSE015B018A PSE015B024A PSE015B030A HEATING Btuh EER CFM 12000 16000 200 24500 12000 16000 200 24500 12000 16000 200 24500 12000 16000 200 24500.8 9.8 9.8 9.8 9 540 960 450 960 450 960 450 960 240V Kw/Hr Btu/Hr 208V Kw/Hr Btu/Hr 4.8 16300 3.6 12300 7.3 24600 5.5 18400 9.6 32700 7.2 24600 14.4 490.8 36900 Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 w w w. n a p o l e o n h e a t i n g a n d c o o l i n g. c o m
3 ELECTRICAL AND PHYSICAL DATA TABLE 2. Voltage/Hz/Phase Voltage/Range Model No. Min. Circuit Ampacity Max. Overcurrent Protection Fuse / Ckt Breaker (A) 208V 240V 208V 240V Compressor Outside Fan Comp Rated Load Amps (RLA) Comp Locked Rotor Amps (LRA) Dia Cond Mtr. HP Indoor Blower Nominal RPM Rated Load Amps Wheel Dia x Width Rated Load Amps HP PSE005B012A 25.1 28.5 30.0 30.0 5.3 28.5 10 0.79 1/4 PSE005B018A 25.1 28.5 30.0 30.0 7.4 38.5 10 0.79 1/4 17-3/4" PSE005B024A 25.1 28.5 30.0 30.0.0 34.8 1600 1.40 1/3 PSE005B030A 25.1 28.5 30.0 30.0 12.8 67.8 1600 1.40 1/3 x 6 2.8 1/ 3 208-230/60/1 197-253 PSE007B012A 36.5 41.5 40.0 45.0 5.3 28.5 10 0.79 1/4 PSE007B018A 36.5 41.5 40.0 45.0 7.4 38.5 10 0.79 1/4 17-3/4" PSE007B024A 36.5 41.5 40.0 45.0.0 34.8 1600 1.40 1/3 PSE007B030A 36.5 41.5 40.0 45.0 12.8 67.8 1600 1.40 1/3 PSE0B012A 46.8 53.5 50.0 60.0 5.3 28.5 10 0.79 1/4 PSE0B018A 46.8 53.5 50.0 60.0 7.4 38.5 10 0.79 1/4 17-3/4" PSE0B024A 46.8 53.5 50.0 60.0.0 34.8 1600 1.40 1/3 PSE0B030A 46.8 53.5 50.0 60.0 12.8 67.8 1600 1.40 1/3 PSE015B012A 68.4 78.5 70.0 80.0 5.3 28.5 10 0.79 1/4 PSE015B018A 68.4 78.5 70.0 80.0 7.4 38.5 10 0.79 1/4 17-3/4" PSE015B024A 68.4 78.5 70.0 80.0.0 34.8 1600 1.40 1/3 PSE015B030A 68.4 78.5 70.0 80.0 12.8 67.8 1600 1.40 1/3 Electric heating module components Model Circuit Breaker 1 Circuit Breaker 2 Temperature Cut-out- Auto Reset Fusible Link CEHM005A 30A NA 135 F open, 95 F close 170.6 F (77 C) CEHM007A 45A NA 135 F open, 95 F close 161.6 F (72 C) CEHM0A 60A NA 135 F open, 95 F close 170.6 F (77 C) CEHM015A 30A 60A 135 F open, 95 F close 170.6 F (77 C) Compressor and condenser fan branch circuit fuse size Model Compressor RLA (A) Condenser Motor FLA (A) Fuse Size (A) CACM012B 5.3 0.79 CACM018B 7.4 0.79 15 CACM024B.0 1.40 20 CACM030B 12.8 1.40 30 *All specifications and designs can change without notice to allow for on-going improvements. Images may not be exactly as shown. Consult with your owner s manual for current information. Check all local and national building codes. Napoleon is a registered trade mark of Wolf Steel Ltd. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 www. napoleonheatingandcooling. com
4 AIR FLOW TABLE 3. CFM at External Static Pressure (inches of water Column) Speed Tap# Motor Speed 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1 0% 961 938 914 884 855 819 773 725 651 576 2 85% 892 871 853 839 819 789 750 709 631 569 3 60% 746 723 707 688 663 650 626 598 571 546 4 35% 546 512 492 454 421 386 353 333 318 291 5 25% 455 407 379 332 292 264 250 225 TABLE 4. Model No. PSE005B012A PSE005B018A PSE005B024A PSE005B030A PSE0B012A PSE0B018A PSE0B024A PSE0B030A Available Motor speed Taps Heating/Cooling Speed Heating/Cooling Speed Setting Model No. Setting Module Tap# Module Tap# CEHM005A CEHM007A HI 4* HI 3 CACM012B PSE007B012A CACM012B HI 3 HI 4* G - continuous fan 2 G - continuous fan 2 CEHM005A CEHM007A HI 4 HI 3* CACM018B PSE007B018A CACM018B HI 2 HI 2 G - continuous fan 1 G - continuous fan 5 CEHM005A CEHM007A HI 4 HI 3* CACM024B PSE007B024A CACM024B HI 2 HI 2 G - continuous fan 1 G - continuous fan 5 CEHM005A CEHM007A HI 4 HI 3 CACM030B FACTORY 1 PSE007B030A FACTORY 1 CACM030B HI NA HI NA G - continuous fan 3 G - continuous fan 5 CEHM0A FACTORY 2 CEHM015A HI 3 HI 1 CACM012B PSE015B012A CACM012B HI 4* HI 4 G - continuous fan 2 G - continuous fan 3 CEHM0A FACTORY 2 CEHM015A HI 3* HI 1 CACM018B PSE015B018A CACM018B HI 2 HI 2* G - continuous fan 5 G - continuous fan 5 CEHM0A FACTORY 2 CEHM015A HI 3* HI 1 CACM024B PSE015B024A CACM024B HI 2 HI 2* G - continuous fan 5 G - continuous fan 5 CEHM0A FACTORY 2 CEHM015A HI 3 HI 1* CACM030B FACTORY 1 PSE015B030A FACTORY 1 CACM030B HI NA HI NA G - continuous fan 5 G - continuous fan 5 *IMPORTANT: Do not use common speed tap for multiple functions; Connecting (any combination of) air conditioning blower speed, heating blower speed, and continuous fan speed to the same motor speed tap will cause the unit to malfunction. Each of the three blower functions must be connected to separate motor speed taps. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 www. napoleonheatingandcooling. com
5 DIMENSIONS WALL SLEEVE DIMENSIONS FOUR DIFFERENT WALL SLEEVE MODELS ARE DEPICTED BELOW: NOTE: TO IMPROVE RIGIDITY AND REDUCTION IN VIBRATION WALL MOUNTING BRACKETS CAN BE USED TO AFFIX WALL SLEEVE TO BUILDING SUB STRUCTURE FROM INSIDE OR OUTSIDE OF THE BUILDING. ENGINEER/ARCHITECT TO CONSULT WITH NAPOLEON ENGINEERING TO DETERMINE BRACKET LOCATION FOR SETTING THE DESIRED DEPTH OF WALL SLEEVE INTO WALL. CWSMUA CWSMUA15 CWSMUA17 CWSMUA19 DIMENSIONS FOR THE TOP PANEL (ITEM 1): <== CWSMUA <== CWSMUA15 <== CWSMUA17 <== CWSMUA19 WALL SLEEVE IS DIRECTLY LAGGED TO WALL SUBSTRUCTURE. 16.000 17.000 19.000 3 3 4 " 28 7 8 " POSITION A 1" POSITION B 42 1 4 " CENTRAL BRACE MOUNTING LOCATIONS 46 7 8 " 44 7 8 " 15 16 " 26 1 2 " 32 3 4 " 12.590 14.890 16.890 18.890 DIMENSIONS FOR THE SIDE PANELS (ITEM 3 & 4)): <== CWSMUA <== CWSMUA15 <== CWSMUA17 <== CWSMUA19 Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 www. napoleonheatingandcooling. com
6 ENCLOSURE FOR CONDO PACK 0" MIN. CLEARANCE * 2" MIN. CLEARANCE 0" MIN. CLEARANCE 30" RECOMMENDED unobstructed clearance in front of the unit for servicing 29" REF. DOOR OPENING 1" REF 1.5" Ø (" RECOMMENDED MIN. CLEARANCE FOR SERVICING) * If less then, servicing may be performed by opening the front door panels and the heating module may need to be removed to access components. Space required for Return Air Ducting must be considered. Flashing Seal around Sleeve and INSIDE wall 1" REF. CLEARANCE BETWEEN LEFT (HINGE) SIDE DOOR JAM AND CONDO PACK 32 " *** DRAIN REQUIRED (1.5" Ø MIN.) FOR REMOVAL OF AC CONDENSATE *** Recommended unobstructed clearance in front of the unit NOTE ** Engineer/Architect - to consult with Napoleon Engineering to determine bracket location for setting the desired depth of Wall Sleeve into wall. A A-A Flashing 2" MIN. CLEARANCE TO COMBUSTIBLE 32 1/8" REF. * **SECURE TO WALL 82" REF. 43 1/8" 44 7/8 " REF. FLOOR 8" MIN. FABRICATED WOOD OR STEEL SUPPORT A DRAIN 16 " 12 9/16" Brick Wall PROTRUDE 1/2 MIN.-1 MAX. Seal around Sleeve and OUTSIDE wall PROTRUDE 1/2 MIN.-1 MAX. Brick Wall ROUGH OPENING TO SUIT 28 7/8" X 44 7/8" WALL SLEEVE 28 7/8" 44 7/8 " REF. VIEW OF OUTSIDE WALL Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 www. napoleonheatingandcooling. com
7 CONDO PACK SHOWN IN WALL SLEEVE 8" MIN FLOOR 20 1 2 " 8" 3 1 2 " 43 1 8 " 1 1 16 " 7 1 8 " 15 16 " 16" 3 1 8 " 24 1 4 " AIR SUPPLY OUTLET 28" 29" ELECTRICAL CONNECTION 1 15 16 " 24 1 8 " 1 15 16 " AC DRAIN AIR RETURN INLET 28 7 8 " WALL SLEEVE CONDO PACK UNIT HEATING MODULE MODULE (AIR CONDITIONER) 12 9 16 " 1 25 16 " 32 8 1 " Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 www. napoleonheatingandcooling. com
8 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 PHONE: 866-820-8686 FAX: 705-725-1150 Website: www.napoleonheatingandcooling.com General: hvac@napoleonproducts.com Technical inquiries: hvacsupport@napoleonproducts.com Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada phone 866-820-8686 fax 705-725-1150 www. napoleonheatingandcooling. com