Night & Day: DRINKING-WATER HYGIENE AQUAFIT - the innovative single-lever mixer for safety and hygiene
Maximum protection, maximum hygiene Preserving water quality in all drinking water installations For many people today, being able to use clean drinking water is still not a matter of course, even though the United Nations in 2010 recognized access to clean drinking water as a human right. Assuming a correspondingly appropriate infrastructure, operators of drinking water installations are thus responsible for ensuring the availability of perfect water quality. Improperly constructed and operated drinking-water systems can cause the originally clean water to become contaminated within a building. The main causes are stagnation and critical temperatures. With the option for hygiene flushing and thermal disinfection, Franke s innovative series of AQUAFIT fittings supports operators in their responsibility to ensure highest drinking water hygiene day and night. The compulsory functions of intelligent mixer valves are: Protection against scalding by limiting the hot water temperature to a maximum of 43 C (according to code of practice) Ensuring that drinking water is hygienic, by performing hygiene flushing and thermal disinfection Providing sensitive temperature control even for users with reduced motor skills, by means of a large comfort zone within the temperature range from 34 C through 38 C 2
Regulatory requirements European Drinking Water Directive 98/83/EC (EU: 31998L0083) on the quality of water intended for human consumption This directive defines a maximum lead content of 10 µg/l drinking water in the EU. This limit comes into force on 01.12.2013 Swivel angle 95 Selected planning assumptions according to DIN EN 806-2 Where required by regulations, taps and fittings must be equipped with scald protection A water temperature of 43 C at the discharge point is recommended Thermostatic mixers for limiting water temperature must be in compliance with DIN EN 1111 38 C 34 C Excellent mixing performance by means of a lever with a wide range of adjustment and large comfort zone (35 swivel angle) for extremely fine temperature control 38 C 34 C 15 C Comfort zone safety in compliance with DIN EN 1111 Active scald protection The AQUAFIT single-lever mixer is offered with a novel ceramic cartridge supplied in two variant forms. Besides the standard version with its adjustable temperature stop, Franke offers a comfort model featuring thermostatic scald-protection (in compliance with DIN EN 1111). With its compact design, this cartridge ensures a DIN EN 806-2 regulation-compliant limitation of the hot water temperature to a maximum of 43 C, and stops water flow in the event of cold water failure. A thermocouple integrated in the mixer cartridge ensures protection against scalding. 3
Hygiene by remote control Flushing and disinfecting without the need for manual opening No-touch hygiene this is made possible by combining the AQUAFIT single-lever mixer with an optional hygiene unit. It consists of a function block made of low-lead brass with a solenoid valve cartridge, which connects directly from the underside of the washbasin to the fitting base of the lever mixer. With two cables which are preferably laid in an empty tube, the solenoid valves are connected to the electronic control unit mounted on the wall beneath the washbasin. The additional function block provides the features necessary for subjecting the AQUAFIT single-lever mixer to regulation-compliant disinfection and to perform automatic hygiene flushing for all water-conducting parts. The optional remote control can be used to change the factory-set parameters, such as flushing duration and flushing interval as well as the settings for thermal disinfection. In addition, program-controlled thermal disinfection can be started by the simple press of a button. Awarded tap innovation: The new AQUAFIT single-lever mixer won the Special Mention award for specific design quality in the category home interior. This award is a part of the German Design Award 2014 by the German Design Council. With its clear linework and ergonomic mixing lever, the AQUAFIT single-lever mixer facilitates easy and convenient operation for all users. Thanks to the flat, abrasionresistant mixer marking, the fitting is easy to clean. An integrated flow controller, which guarantees a constant flow of 6 l/min, ensures that our important water resources are used economically. 4 4
... FOR ALL sanitary facilities Innovative fitting technology also for accessible sanitary rooms Persons with physical disabilities will not need to do without the advantages offered by the AQUAFIT single-lever mixer. With its newly designed 150 mm lever cap, the AQUAFIT single lever mixer is now available for accessible sanitary rooms. The extended, ergonomic handle lever provides all users with the means for comfortable and safe hand washing. The clear and easy operability of this fitting model is based on the two-senses principle. On the one hand the easy-to-grasp lever shape, with its slight curvature and finger recess in the front area, serves as a tactile aid. On the other hand the highcontrast laser-etched top surface of the lever provides visual support and orientation. The AQUAFIT for accessible wash facilities is equipped with a solenoid cartridge which offers thermostatic scald-protection as a standard. A pressure-independent laminar jet controller with a constant flow rate of 6 l / min is also a standard feature of this fitting. Laminar jet controllers are particularly suitable for use in hygienically sensitive areas such as hospitals and nursing facilities. 5
The guarantee for sound drinking water: Hygiene unit for AQUAFIT single-lever mixer, consisting of: Fitting block with two solenoid valves Electronic control unit Remote control for setting the function parameters for thermal disinfection and hygiene flushing Hygiene flushing: The preset hygiene flushing routine automatically opens both solenoid valves after 24 hours, and keeps them open for 3 minutes to ensure a sufficient exchange of water although the mixing lever is closed. The remote control can be used to make changes to the parameters for flush-interval and flush duration, and to select the solenoid valve. Thermal disinfections: For thermal disinfection, the temperature of the inner surface of the single-lever mixer is increased to 70 C for 5 minutes, in compliance with regulations. Parameters such as exposure time and cooling time can be adjusted by remote control to meet specific building requirements. Put a stop to legionella & Co. Thermal disinfection reduces the risk of legionella infection Thermal disinfection is started by remote control. An electronic pulse is transmitted via the electronic control unit to the solenoid valve on the hot water side. Water with a temperature of at least 70 C flows through the water-conducting inner surfaces of the fitting via the function block and directly to the outlet. The factory-set treatment time is 5 min, subdivided into 2 min of water and energy saving permanent water flow and 3 min of pulsating water delivery. During the subsequent cooling period, the cold water side opens for 10 seconds and removes residual hot water from the tap. The operator can use the remote control to change these parameters at any time. Normal operation Hygiene flushing Thermal disinfection 6 for parameter changes for triggering and parameter changes
Hygiene unit for AQUAFIT single-lever mixer Hygiene unit for AQUAFIT single-lever mixer for performing automatic hygiene flushing and program-controlled thermal disinfection. Consisting of function block with 2 solenoid valve cartridges for installation at the single-lever mixer below the washbasin and an electronic control unit in a housing with stainless steel cover plate for wall-mounting, for battery or mains operation. Function block made of low-lead brass in accordance with the recommendations of DIN 50930-6. Integrated control function: - Hygiene flushing (3 min.), fixed interval every 24 hours Setting of function parameters via optional remote control: - fixed intervals (8, 24, 48 or 72 hours) and flush duration (10 sec. 10 min) for automatic hygiene flushing, cold and hot water - Application time: 3 20 min., cooling down period: 10 60 sec. for thermal disinfection - Parameters for thermal disinfection: application time: 3 min., cooling down period: 10 sec. (can be activated via optional remote control) - Activation of thermal disinfection Type Article number for AQUAFIT single-lever mixer with connecting hoses Z-AQFT0001 2000110483 for AQUAFIT single lever mixer with connecting pipes Z-AQFT0002 2000110484 Technical details Volume flow rate thermal disinfection: 0,03 l/s at a flow pressure of 3 bar Volume flow rate hygiene flushing: PWC 0,05 l/s; PWH 0,02 l/s at a flow pressure of 3 bar Supply voltage: 6 V DC Power consumption: 3 W Type of protection: IP 67 Necessary accessories (alternatively) Battery compartment with battery 6 V Z-AQCT0003 2000109466 AC adapter plug Z-PRTRS0001 2000105799 Mains power supply for installation in the wall Z-AQCT0001 2000109417 Optional accessories Remote control unit for setting the function parameters Z-AQUA091 2000101087 Note The AQUAFIT single-lever mixer is to be ordered separately. Status: 05.15 7
AQUAFIT single-lever mixer for accessible areas AQUAFIT single-lever mixer for accessible areas, with thermostatic scald-protection AQUAFIT single-lever mixer DN 15 with mixing cartridge, ceramic discs and thermostatic scald-protection in accordance with DIN EN 1111, permanently adjusted for maximum of 38 C, as a pillar mixer for accessible sanitary facilities according to DIN 18040. Ergonomic lever handle based on the two-senses principle (tactile and visual). With optional hygiene unit for performing automatic hygiene flushing and program-controlled thermal disinfection, mixing cartridge with thermal regulating unit and safety shut-off in the event of cold water supply failure. Laminar jet controller and integrated flow controller. For connection to hot and cold water. Full-metal design, polished chromium-plated brass. Tap housing made of low-lead brass in accordance with the recommendations of DIN 50930-6, with connecting hoses and strainers. Type Article number AQFT0019 2030017091 Model with connecting pipes AQFT0020 2030017096 Technical details Minimum flow pressure: Calculation flow rate: Volume flow rate: 1 bar PWC 0,07 l/s, PWH 0,07 l/s 0,10 l/s at a flow pressure of 1,2 bar Optional accessories Hygiene unit and power supply Note For performing hygiene flushing and thermal disinfection, hygiene unit and power supply are required separate accessories. Status: 05.15 8
AQUAFIT single-lever mixer AQUAFIT single-lever mixer with thermostatic scald-protection AQUAFIT single-lever mixer DN 15 with mixing cartridge, ceramic discs and thermostatic scald-protection in accordance with DIN EN 1111, permanently adjusted for maximum of 38 C. For public and commercial sanitary facilities as a pillar mixer with optional hygiene unit for performing automatic hygiene flushing and program-controlled thermal disinfection, with aerator and integrated flow controller. Mixing cartridge with thermal regulating unit and safety shut-off in the event of cold water supply failure. For connection to hot and cold water. Full-metal design, polished chromium-plated brass. Tap housing made of low-lead brass in accordance with the recommendations of DIN 50930-6, with connecting hoses and strainers. Type Article number AQFT0017 2030017069 Model with connecting pipes AQFT0018 2030017084 AQUAFIT single-lever mixer with temperature stop AQUAFIT single-lever mixer DN 15 with mixing cartridge, ceramic discs and adjustable temperature stop. For public and commercial sanitary facilities as a pillar mixer with optional hygiene unit for performing automatic hygiene flushing and program-controlled thermal disinfection, with aerator and integrated flow controller. For connection to hot and cold water. Full-metal design, polished chromium-plated brass. Tap housing made of low-lead brass in accordance with the recommendations of DIN 50930-6, with connecting hoses and strainers. Type Article number AQFT0001 2000106659 Model with connecting pipes AQFT0002 2000106660 Technical details Minimum flow pressure: Calculation flow rate: Volume flow rate: 1 bar PWC 0,07 l/s, PWH 0,07 l/s 0,10 l/s at a flow pressure of 1,2 bar Optional accessories Hygiene unit and power supply Note For performing hygiene flushing and thermal disinfection, hygiene unit and power supply are required separate accessories. Status: 05.15 9
AQUAFIT / 05.2015 / EN-INT / Changes in dimensions, construction and models reserved Franke Water Systems ws-info.int@franke.com www.franke.com 2