DIRECT LIT LED FLAT PANEL: SAVER SERIES USER MANUAL by INSTALLATION GUIDE FOR: 1X4: MLFP14DS4035 MLFP14DS4041 MLFP14DS4050 2X2: MLFP22DS4035 MLFP22DS4041 MLFP22DS4050 2X4: MLFP24DS4235 MLFP24DS4241 MLFP24DS4250 Thank you for purchasing this MaxLite product. For additional information or assistance please e-mail info@maxlite.com or log on to www.maxlite.com and click on the Information and Quotes bar. 12.30.13
TABLE OF CONTENTS DESCRIPTION & CAPABILITIES...1 TECHNICAL SPECIFICATIONS... 2 FEATURES... 3-4 MOUNTING PANELS IN CEILING... 5 SET-UP... 6 CONNECTING TO AC POWER SOURCE... 7 SET-UP FOR OPTIONAL IR REMOTE... 8 SET-UP FOR 0-10V BALLAST DIMMER Building Controls / Daylight Harvesting... 9 SET-UP FOR 0-10V SIMPLE WALL DIMMING... 10 SET-UP FOR LINKING PANELS... 11
1 DESCRIPTION & CAPABILITIES DESCRIPTION Models: Available in 1 x4, 2 x2, 2 x4 Construction: A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2 x2 and 2 x4 fluorescent fixtures. The profile is slim, only 4.1 inches deep including the junction box, making it ideal for low depth ceiling cavities. The housing provides maximum heat sink and thermal control. The lens is a translucent white polycarbonate. CAPABILITIES On/Off: Panels can operate independently, or can be daisy chained together to work with standard on/off wall switches. Dimming: Panels are fully dimmable with a standard 0-10V wall dimmer, the optional hand-held remote dimmer, and Building Controls. Building Controls: With the addition of Controls the panels can be automated and customized to room use. Daylight Harvesting: Added to Building Controls enable user to further reduce energy consumption by taking advantage of natural light entering the room. Linking: Up to 20 panels can be linked from the master panel.
TECHNICAL SPECIFICATIONS 1 x 4 Life: 100,000 hour life based on L70/TM-21@25 C Self-Driven: No additional drivers required Power: Connect directly to AC power supply 120V through 277V Contains No Hazardous Material: Mercury and UV Free # Of LEDs: 120 Wattage: 40W Nominal Lumens: 3400-3600 CRI: 82 Color Temperature: 3500K, 4100K and 5000K Weight: 9 lbs. 2 x 2 Life: 100,000 hour life based on L70/TM-21@25 C Self-Driven: No additional drivers required Power: Connect directly to AC power supply 120V through 277V Contains No Hazardous Material: Mercury and UV Free # Of LEDs: 132 Wattage: 40W Nominal Lumens: 3500-3800 CRI: 82 Color Temperature: 3500K, 4100K and 5000K Weight: 9 lbs. 2 x 4 Life: 100,000 hour life based on L70/TM-21@25 C Self-Driven: No additional drivers required Power: Connect directly to AC power supply 120V through 277V Contains No Hazardous Material: Mercury and UV Free # Of LEDs: 264 Wattage: 42W Nominal Lumens: 4100-4550 CRI: 82 Color Temperature: 3500K, 4100K and 5000K Weight: 18 lbs. 2
3 FEATURES Back Panel IR Dimming Option Knock Out Opening Pass Thru Wire Access Control Box Knock Outs Wire Tie Off Loops Face Frame Clip Control Box Removed Option Module Mounting Studs Red/Blue LED board Leads /Yellow/ Option leads Driver Black, White, Green for connection to AC power source and ground
FEATURES Optional Dimming Control - Features LED Board Leads Driver Optional IR Dimmer Controller IR Eye Connector 4 0-10V Option/Accessory Leads IR Eye-Unit
5 MOUNTING PANELS IN CEILING Ceiling Grid Groove: 1) The MaxLite LED Flat Panels are designed to lay into a gridded ceiling. Simply start on one side and gently lay down the panel. 2) Open seismic hanger 180 to engage ceiling grid frame. * Model shown for reference only * Note: Uniform support is vital; for safety purposes, each panel must have support wire attached. Safety Wire Hangers: Safety hanger loops on the back of the panel to accept wire from the ceiling structure. Thread wire through the loop and finish off as for any other suspended or grid fixture.
M S ZONES SET-UPs 1. On/Off and AC Power Connection (Pg.7) ON 2. Optional IR Remote (Pg.8) 3. 0-10 Ballast/Building Controls (Daylight Harvesting) (Pg.9) 4. Simple Wall Dimming (Pg.10) POWER UP MIN MAX DOWN 5. Linking Panels: Link up to 20 panels from master using option/accessory leads (Pg.11) 0-10 0-10 0-10 6 0-10 Dimmer
7 CONNECTING TO AC SOURCE Connecting panels to AC source supply: All units must be individually connected to the AC supply. (120-277 VAC) Black = Line White = Neutral Green = Ground AC supply connections ON/OFF operation: Black line connection to be made to the switched lead from source.
1. Follow Connecting Power procedures (see page 6). SET UP OPTIONAL I.R. REMOTE 2. Connect option leads from dimmer control to driver violet, yellow, grey Power Supply IR Sensor Yellow IR DIMMER Module! Caution: Do NOT connect high voltage to option leads. Permanent damage will occur. 3. Connect IR Sensor Cable to Dimmer controller input labeled IR after cover is reinstalled. Note: If building control or wall control for linking is used, do not use IR remote. 4. Position IR Sensor so it can be visible to the Remote Controller 5. IF IR REMOTE IS TO BE USED IN THE WALL CRADLE ACCESSORY Locate Sensor In Room 6. Multiple linking of panel to IR remote 8 Note: The IR sensor must be positioned in close proximity to the remote.
SET UP 0-10V BALLAST DIMMER BUILDING CONTROLS 1. Follow Connecting Power procedures (see page 6). 2. Locate the option leads violet, yellow, grey From Controller 3. 0-10 connection as shown CURRENT SOURCING CENTRAL SYSTEM CONTROLLER CENTRAL SYSTEM CONTROLLER Output 0-10 Wire to violet/yellow/grey option leads (As Shown) + Yellow Input 0-10 DRIVER! Caution: Do NOT connect high voltage to option leads. Permanent damage will occur. 4. Mount panel, feed line through knockouts, and operate to controller 9
SET UP FOR WALL DIMMING (0-10V SIMPLE DIMMING) 1. Follow Connecting Power procedures (see page 6). 2. Locate the option leads violet, yellow, grey From Dimmer 4. Connect wall dimmer (non-relay wires) to option Controller Wires. 0-10 connection as shown with wire nuts WALL DIMMER Output 0-10 Yellow Input 0-10 DRIVER! Caution: Do NOT connect high voltage to option leads. Permanent damage will occur. 5. Mount panel, feed line through knockouts, and operate to wall dimmer 0
11 SET-UP FOR LINKING PANELS 1. Select one of the panels to be Master Panel. Master panel will have initial 0-10 option connect as shown WALL DIMMER Output 0-10 Yellow Input 0-10 DRIVER 2. Connect by linking to option 0-10 input. and grey wires are the 0-10 input wires! Caution: Do NOT connect high voltage to option leads. Permanent damage will occur. 4. Continue this for each additional panel up to 20 panels. 0-10 0-10 0-10 0-10 Dimmer Panel 1 Panel 2 Panel 3 WALL DIMMER DRIVER DRIVER DRIVER Output 0-10 Yellow * * *Cap off un-used yellow leads
Lighting Possibilities For additional information or assistance please e-mail info@maxlite.com or log on to www.maxlite.com and click on the Information and Quotes bar.