Wireless Alarm System User Manual
1. Configuration List Wireless Alarm Receiver Solar& Wireless Photoelectric Beam Sensor English Manual 1 piece (includes 1 set installation accessories) 1 pairs (includes 1 set installation accessories) 1 piece Note: The alarm system has been programmed already,please operate the system according to the part 3 of the manual; If you want to add additional detectors to the system,please operate the system according to the part 4 of the manual or contact us directly; 2. System Components And Usage Wireless Alarm Receiver Indicator Light Speaker Indicator Light: Will be red if power on;will be flashing if on setting mode Speaker: Will alarm for 5 seconds if the detector be triggered Backup Battery Compartment Backup Battery Compartment:4 pieces AA 1.5V batteries(can keep the wireless alarm receiver working continuously for 100 hours if AC power off) 1
Power Tone Button ON/OFF Power : power jack(dc5v) ON/OFF: power switch(turn on/off the wireless alarm receiver) set button(add/delete the detectors of the wireless alarm receiver) Tone Button: switch the ring tones(total 4 ring tones optional) Solar & Wireless Photoelectric Beam Sensor Horizontal Pipe Infrared Beam Calibration Hole Infrared Beam Solar Panel Receiver Transmitter Screw Hole ON/OFF Charge Jack Charge Jack ON/OFF Transmitter Receiver 2
Horizontal Pipe: easy to know the beams be installed vertically Infrared Beam: used to detect the intruder Calibration Hole: easy to align with another beam sensor if the beams apart far away Solar Panel: charge the battery of the beam sensor even in cloudy or rainy days ON/OFF: turn on/off the solar beam sensor(press the ON/OFF button once) Charge Jack:pull out the red plug to charge the solar beam sensor by DC5V-12V power adapter if the battery of the beam sensor go flat Screw Hole: used to fix the installation accessories 3. Operation Instructions Step 1 Power on the wireless alarm receiver by the power adapter. Power light up (Indicator light up means the wireless alarm receiver work normally) Step 2 Turn on the Solar&Wireless Photoelectric Beams:Press the ON/OFF button once(both the transmitter and receiver) ON/OFF ON/OFF Transmitter Receiver (the light of ON/OFF button will be red if work normally) 3
Step 3 Make sure the beams aligned with each other ON/OFF ON/OFF Transmitter Receiver (if work normally,the light of the Receiver's ON/OFF button will go off after flashing about 10 seconds; and the light of the Transmitter' s ON/OFF button will go off after about 30 seconds ) Step 4 Trigger The Solar&Wireless Photoelectric Beam Sensor, and the wireless alarm receiver will alarm for 5seconds (Completely block all the 2 infrared beams) ON/OFF Transmitter Receiver (the light of the Receiver's ON/OFF button will flash 3 times means the beam sensor be triggered and send the alarm signal;and then the solar beams will back to work mode automatically after about 5 seconds) Step 5 Installations Solar&Wireless Photoelectric Beam Sensor 1 st Installation method 4
5
6
4. Other Settings (1)How to add detectors to the wireless alarm receiver ADD Step 1 Power on the wireless alarm receiver by the power adapter Step 2 long time press the ON/OFF button for 5 seconds and release the button when the indicator light flashing; light up flashing 7 ON/OFF press the ON/OFF button for 5 seconds ON/OFF release the button
Step 3 Trigger the detector(for example,trigger the solar&wireless photoelectric beam sensor) stop flashing (a bleep prompt and the indicator light stops flashing means the detector has been added to the wireless alarm receiver successfully) Step 4 Trigger the detector again to confirm the detector has been added to the wireless alarm receiver already. (2)How to delete the detectors of the wireless alarm receiver Step 1 Power on the wireless alarm receiver by the power adapter Step 2 long time press both the ON/OFF button and Tone Button for 10 seconds and release the buttons when you heard a long bleep; Note: all the detectors will be deleted by this operation; ON/OFF Tone Button 8 (3)How to switch the ring tones Step 1 Power on the wireless alarm receiver by the power adapter Step 2 Make sure the wireless alarm receiver has added the detectors already
Step 3 Press the Tone Button once to switch the ring tones(total 4 ring tones optional) Tone Button 5. Technical Parameters Wireless Alarm Receiver 2.04" 6.38" Technical parameters Item Working Voltage Working Current Wireless Frequency Backup Battery Technical Parameters DC5V Static Current 20mA; Alarming Current 300mA 433MHz FSK+FHSS 4 pieces AA 1.5V batteries(package is not included) 9
Solar&Wireless Photoelectric Beam Sensor 1.97" 10.43" 7.36" 10.43" 3.34" 1.54" 3.31" 1.57" 1.77" Technical parameters Item Infrared Detection Range Wireless Transmission Range Beam Quantity Wireless Frequency Maximum Trigger Number In 24 Hours Working Voltage Battery Type Battery Capacity Static working Current Infrared Wavelength Solar Panel Output Current Technical Parameters 190 feet 1/4 mile 2 433MHz FSK+FHSS 200 times 3.3V Chargeable LiFePO4 Battery Transmitter:500mAh,Receiver:500mAh 0.5mA 940nm±20nm Working Temperature Range -30 ~70 1800L ux illumination levl: 2mA(Remarks: Remarks: The outdoor illumination intensity on rainy days is about 2000L ux) 10