manufacturer of products from polypropylene GAS WASHERS
CONTENT Introduction...2 1. Horizontal gas washers «Maximov»...3 1.1 Gas washer «Maximov», type «GM-2»...3 Additional configuration of gas washer «Maximov GM-2»...6 1.2 Gas washer «Maximov», type «GM-4»...7 Additional configuration of gas washer «Maximov GM-4»...10 1.3 Gas washer «Maximov», type «GM-5»...11 Additional configuration of gas washer «Maximov GM-5»...14 2. Vertical gas washers «Maximov»...15 2. 2 Venturi scrubber...18 3. Fibrous filters FVG-PP-UA...20 1
Introduction «Maximov» gas washers (or scrubbers) are intended to clean the air contaminated with acid and alkali fumes, usually at electroplating industries, laboratories and in technological processes. «Maximov» gas washers including all its inner parts (nozzle, sprayers, pipelines, pump, valve, level sensor, рн-indicator) are manufactured from polypropylene (PP). On your request we can produce scrubbers from other polymers PP and its modifications: PVC (polyvinylchloride), PE (polyethylene), PVDF (polyvinylidene fluoride). Scrubbers can be of two types: horizontal and vertical. Horizontal scrubbers «GM» are more compact and enable cleaning at high speeds of air-gas flow. The capability of scrubber series is 800 68800 m3/h. The scrubber s resistance depends on model and can reach 300 800 Pa; scrubbers are intended for gas temperature 5 65 grades. The temperature of installation site: +5 +40 C indoors (modification for outdoor use by -30 +30 C is possible on special request). The efficiency of gas washers is 99 % for particles min. 15 micron. Depending on air-gas flow and operating side there are possible length and right types of body location. For aerodynamic reasons a straight pipe must be planned with a length of at least 3 times of the pipe diameter for the air inlet. Also it is recommended to plan at the outlet side a straight pipe of at least up to 1 meter. The necessary parameters for selection: 1. The capability, m³/h; 2. The gas temperature, grades; 3. The content of air-gas medium (the chemical formula, e.g. HCl, H2SO4, NAOH...); 4. The concentration of vapours before the scrubber entrance, mg/m³; 5. The necessary affectivity or the concentration at the outlet side (mg/m³). Available types of plastic: made in Russia Abbreviation Designation Temperature range, ºC PP-BC (ПП-БС) polypropylene block copolymer -40 +80 Default basic material PP-H (ПП-Г) polypropylene homopolymer -5 +105 HDPE (ПНД) polyethylene -50 +80 made in Germany Abbreviation Designation Temperature range, ºC PVC polyvinylchloride 0 +60 PVDF polyvinylidene fluoride -30 +140 PPs PP-EL-s flame-resistant polypropylene electrically conductive, flame-resistant polypropylene 0 +100 0 +80 Specifications of thermoplastics The customer and/or design company choice the type of thermoplastics according to the temperature, composition and concentration of the media based on data from the table of chemical resistance thermoplastics and operation experience. 2
1. Horizontal gas washers «Maximov» 1.1 Gas washer «Maximov», type «GM-2» The simplest type of wet horizontal gas washer «GМ-2» has spray chamber and multistage polymeric demister system and is referred to hollow scrubber. It is intended for weak concentrations with the gas temperature max. 40 C. Not applicable for mixtures of acids. Principle of operation: Horizontal scrubber, type «GМ-2» works on binding principle of airborne and dust particles with scrubbing liquid. The airflow is irrigated continuously with water (solution) by double sprayers. They spray the liquid in two directions: against airflow and along airflow. 3
The process of catching is available in wet scrubbers due to condensing effect enlargement of vapours and particles due to the condensation of water vapours on them. After the air flow with contaminants combined by scrubbing liquid transfers in demisters where the scrubbing liquid is segregated from gas-air mixture. Due to bends of demister s profile the drops are settled on the surface and after they flow down in drain chamber from which the scrubbing liquids goes to the buffer vessel through the hydraulic seal. The hydraulic seal enables the discharged operation of scrubber. After that the liquid is transferred by means of pump for cleaning. The gas washer can be equipped with coagulator optional. The coagulator is integrated between demister s elements accordingly that the smallest particles can enlarge and segregate on demisters. Attention! On customer s request we can complete this type of gas washer with fibrous filter cassette. It provides more quality cleaning from the most hard-separable small aerosol particles. 4
Table 1. Technical characteristics Diameter Consumption L H a b c Pump Weight Dn, мм Q, м³/час mm mm mm mm mm Р, kw m1, kg 160 800-1199 1540 1205 1400 800 570 0,37 99 180 1200-1499 1540 1205 1400 800 570 0,37 99 200 1500-1899 1540 1205 1400 800 570 0,37 99 224 1900-2299 1540 1255 1400 800 570 0,37 103 250 2300-2899 1540 1255 1400 800 570 0,37 104 280 2900-3599 1540 1355 1400 800 570 0,37 115 315 3600-4399 1540 1355 1400 800 570 0,37 115 355 4500-5699 1540 1405 1400 950 570 0,37 127 400 5700-7199 1540 1455 1400 1000 570 0,37 134 450 7200-8999 1540 1555 1400 1100 570 0,37 153 500 9000-11099 1540 1605 1400 1150 570 0,37 162 560 11100-13999 1640 1655 1500 1250 570 0,37 180 630 14000-17699 1720 1755 1580 1350 570 1,1 210 710 17700-22399 2030 1840 2300 1450 570 1,1 269 800 22400-28399 2130 1940 2300 1550 570 1,1 295 900 28400-35599 2230 2050 2300 1650 570 1,1 321 1000 35600-44099 2330 2240 2300 1850 570 1,1 377 1120 44100-55199 2430 2340 2500 1950 570 2,2 424 1250 55200-68800 2530 2540 2500 2150 570 2,2 484 The resistance is 300 450 Pa. Types of casing Left with side load Right with side load Left with topload Right with topload 5
Additional configuration of gas washer «Maximov GM-2» Described in this catalogue gas washer GM-2 can be equipped optional with the fibrous filter cassette FVG-PP-UA. The fibrous filters FVG-PP-UA fall in between wet scrubbing and filter devices. The fibrous filters based on principle of gravity sedimentation are widely used to clean dust-gas-air emissions in many spheres and as a drop catcher or mist extractor. The fibrous filters from PP is intended for air washing from the most hard-separable small aerosol particles, mist of acids, resinous and oily aerosols with particle loading at least 10 micron. Also the fibrous filters are used to filtrate mists of solutions within the chemical reactions by different work activities. The distinction of fibrous filters is their high performance and compactness. The fibrous filter is a cassette with filtering material placed inside the casing of gas washer «Maximov». The filtering material is located in the form of vertical folds in the cassette. The filtering material is a polymeric fabric on basis of polypropylene. The material has purity class G-4 according to EN 779. The filter operates in a mode of accumulation of caught particles on the filtering material s surface with partial draining. 6
1.2 Gas washer «Maximov», type «GM-4» Double-stage wet horizontal gas washer «GМ-4» has packed packed chamber and multi-stage polymeric demister system. It is intended for many acids, alkalis and their mixtures. Principle of operation: Scrubber «GМ-4» works on binding principle of airborne, vapours and dust particles with scrubbing liquid. The airflow gets through the packed chamber that is irrigated continuously with water (solution) by sprayers. They spray the liquid in two directions: against airflow and along airflow. Due to the nozzle in the packed chamber the contact area of liquid with gas-air mixture increases and it improves the efficiency of cleaning. The process of catching is available in wet scrubbers due to condensing effect enlargement of vapours and particles due to the condensation of water vapours on them. 7
After the air flow with contaminants combined by scrubbing liquid transfers in demisters where the scrubbing liquid is segregated from gas-air mixture. Due to bends of demister s profile the drops are settled on the surface and after they flow down in drain chamber from which the scrubbing liquids goes to the buffer vessel through the hydraulic seal. The hydraulic seal enables the discharged operation of scrubber. After that the liquid is transferred by means of pump for cleaning. The gas washer can be equipped with coagulator optional. The coagulator is integrated between demister s elements accordingly that the smallest particles can enlarge and segregate on demisters. Attention! On customer s request we can complete this type of gas washer with fibrous filter cassette. It provides more quality cleaning from the most hard-separable small aerosol particles. 8
Table 2. Technical characteristics Diameter Consumptio L H a b c Pump Weight Dn, mm Q, m³/h mm mm mm mm mm Р, kw m1, kg 160 800-1199 2020 1205 1700 800 570 0,37 125 180 1200-1499 2020 1205 1700 800 570 0,37 125 200 1500-1899 2020 1205 1700 800 570 0,37 126 224 1900-2299 2020 1255 1700 800 570 0,37 132 250 2300-2899 2020 1255 1700 800 570 0,37 133 280 2900-3599 2020 1355 1700 800 570 0,37 151 315 3600-4399 2120 1355 2000 1000 570 0,37 170 355 4500-5699 2120 1405 2000 1000 570 0,37 179 400 5700-7199 2120 1455 2000 1000 570 0,37 188 450 7200-8999 2120 1555 2000 1100 570 0,37 216 500 9000-11099 2120 1605 2000 1150 570 0,37 230 560 11100-13999 2220 1655 2000 1250 570 1,1 260 630 14000-17699 2300 1755 2000 1350 570 1,1 288 710 17700-22399 2510 1840 2300 1450 570 1,1 347 800 22400-28399 2610 1940 2300 1550 570 2,2 382 900 28400-35599 2710 2050 2500 1650 570 2,2 428 1000 35600-44099 2810 2240 2500 1850 570 2,2 508 1120 44100-55199 3060 2340 2700 2000 570 2,2 567 1250 55200-68800 3160 2540 2700 2200 570 4,0 651 The resistance is 600-750 Pa. Types of casing Left with side load Right with side load Left with topload Right with topload 9
Additional configuration of gas washer «Maximov GM-4» Described in this catalogue gas washer GM-4 can be equipped optional with the fibrous filter cassette FVG-PP-UA. The fibrous filters FVG-PP-UA fall in between wet scrubbing and filter devices. The fibrous filters based on principle of gravity sedimentation are widely used to clean dust-gas-air emissions in many spheres and as a drop catcher or mist extractor. The fibrous filters from PP is intended for air washing from the most hard-separable small aerosol particles, mist of acids, resinous and oily aerosols with particle loading at least 10 micron. Also the fibrous filters are used to filtrate mists of solutions within the chemical reactions by different work activities. The distinction of fibrous filters is their high performance and compactness. The fibrous filter is a cassette with filtering material placed inside the casing of gas washer «Maximov». The filtering material is located in the form of vertical folds in the cassette. The filtering material is a polymeric fabric on basis of polypropylene. The material has purity class G-4 according to EN 779. The filter operates in a mode of accumulation of caught particles on the filtering material s surface with partial draining. 10
1.3 Gas washer «Maximov», type «GM-5» This type of scrubbers is used for washing of contaminated air at low speed of connection with scrubbing liquid. First of all it is intended for air cleaning from phosphorus vapours or mixed acid gases. Principle of operation: The gas washer «GМ-5» has larger packed chamber than«gm-4». Scrubber «GМ-5» works on binding principle of airborne, vapours and dust particles with water (solution). The airflow gets through the packed chamber that is irrigated continuously with water (solution) by sprayers. Due to the big size of nozzle in the packed chamber the contact area of liquid with gas-air mixture increases and it improves the efficiency of cleaning. The process of catching is available in wet scrubbers due to condensing effect enlargement of vapours and particles due to the condensation of water vapours on them. 11
After the air flow with contaminants combined by scrubbing liquid transfers in demisters where the scrubbing liquid is segregated from gas-air mixture. Due to bends of demister s profile the drops are settled on the surface and after they flow down in drain chamber from which the scrubbing liquids goes to the buffer vessel through the hydraulic seal. The hydraulic seal enables the discharged operation of scrubber. After that the liquid is transferred by means of pump for cleaning. The gas washer can be equipped with coagulator optional. The coagulator is integrated between demister s elements accordingly that the smallest particles can enlarge and segregate on demisters. Attention! On customer s request we can complete this type of gas washer with fibrous filter cassette. It provides more quality cleaning from the most hard-separable small aerosol particles. 12
Table 3. Technical characteristics Diameter Consumptio L H a b c Pump Weight Dn, mm Q, m³/h mm mm mm mm mm Р, kw m1, kg 160 800-1199 2240 1515 2200 1000 570 1,1 166 180 1200-1499 2240 1515 2200 1000 570 1,1 166 200 1500-1899 2240 1515 2200 1000 570 1,1 166 224 1900-2299 2240 1615 2200 1100 570 1,1 181 250 2300-2899 2240 1615 2200 1100 570 1,1 181 280 2900-3599 2360 1765 2300 1350 570 1,1 227 315 3600-4399 2360 1765 2300 1400 570 1,1 233 355 4500-5699 2360 1815 2300 1400 570 1,1 242 400 5700-7199 2496 1865 2500 1450 570 1,1 266 450 7200-8999 2546 1965 2500 1550 570 2,2 298 500 9000-11099 2710 2015 2650 1600 570 2,2 323 560 11100-13999 2745 2065 2650 1650 570 2,2 352 630 14000-17699 2800 2165 2650 1750 570 2,2 385 710 17700-22399 2830 2265 2650 1850 570 2,2 429 800 22400-28399 3380 2365 3200 1950 570 2,2 509 900 28400-35599 2530 2465 3200 2050 570 2,2 555 1000 35600-44099 2530 2665 3200 2250 570 2,2 648 1120 44100-55199 3580 2765 3200 2350 570 3,0 695 1250 55200-68800 3580 2965 3200 2550 570 5,5 795 The resistance is 630-780 Pa. Types of casing Left with side load Right with side load Left with topload Right with topload 13
Additional configuration of gas washer «Maximov GM-5» Described in this catalogue gas washer GM-5 can be equipped optional with the fibrous filter cassette FVG-PP-UA. The fibrous filters FVG-PP-UA fall in between wet scrubbing and filter devices. The fibrous filters based on principle of gravity sedimentation are widely used to clean dust-gas-air emissions in many spheres and as a drop catcher or mist extractor. The fibrous filters from PP is intended for air washing from the most hard-separable small aerosol particles, mist of acids, resinous and oily aerosols with particle loading at least 10 micron. Also the fibrous filters are used to filtrate mists of solutions within the chemical reactions by different work activities. The distinction of fibrous filters is their high performance and compactness. The fibrous filter is a cassette with filtering material placed inside the casing of gas washer «Maximov». The filtering material is located in the form of vertical folds in the cassette. The filtering material is a polymeric fabric on basis of polypropylene. The material has purity class G-4 according to EN 779. The filter operates in a mode of accumulation of caught particles on the filtering material s surface with partial draining. 14
2. Vertical gas washers «Maximov» The wet vertical gas washer, type «VМ» is intended for air cleaning from many acids, alkalis and their mixtures including impurity gases. Principle of operation: Gas washer «VM» has big nozzle layer that enables to use this gas washer as an absorber. The airflow gets from the bottom upwards through the nozzle layer that is irrigated continuously with water (solution) by sprayers. Due to the big size of nozzle the contact area of liquid with gas-air mixture increases and it improves the efficiency of cleaning. After the air flow transfers in demisters where the scrubbing liquid is segregated from gas-air mixture. Due to bends of demister s profile the drops are settled on the surface and after they flow down in drain layer. The scrubbing liquid goes through the nozzle layer and then it transfers to the buffer vessel through the hydraulic seal. The hydraulic seal enables the discharged operation of scrubber. After that the liquid is transferred by means of pump for cleaning. The gas washer can be equipped with coagulator optional. The coagulator is integrated between demister s elements accordingly that the smallest particles can enlarge and segregate on demisters 15
Vertical scrubbers are divided into three types according to the flow rate: VM-05 scrubber with flow rate 0.5 m/s, resistance until 550 Pa; VM-1 scrubber with flow rate 1.0 m/s, resistance until 600 Pa; VM-2 scrubber with flow rate 2.0 m/s, resistance until 650 Pa. Table 4. Technical characteristics ВМ-05 Diameter Consumptio D H a b c Pump Weight Dn, mm Q, m³/h mm mm mm mm mm Р, kw m1, kg 160 800-1199 900 5350 1900 1300 750 2,2 347 180 1200-1499 1000 5350 2000 1400 750 2,2 389 200 1500-1899 1120 5300 2120 1520 750 2,2 444 224 1900-2299 1250 5500 2250 1650 750 2,2 513 250 2300-2899 1400 5650 2400 1800 750 2,2 599 280 2900-3599 1600 5700 2600 2000 750 5,5 699 315 3600-4499 1800 5650 2800 2200 750 5,5 814 355 4500-5699 2000 5900 3000 2400 750 7,5 930 400 5700-7199 2240 6000 3240 2640 750 7,5 1085 450 7200-8999 2500 6000 3500 2900 750 7,5 1260 500 9000-11099 2800 6000 3800 3200 750 7,5 1482 16
Table 5. Technical characteristics ВМ-1 Diameter Consumptio D H a b c Pump Weight Dn, mm Q, m³/h mm mm mm mm mm Р, kw m1, kg 160 800-1199 650 5300 1650 1050 750 1,1 252 180 1200-1499 710 5300 1710 1100 750 1,1 270 200 1500-1899 800 5300 1800 1200 750 2,2 304 224 1900-2299 900 5350 1900 1300 750 2,2 348 250 2300-2899 1000 5350 2000 1400 750 2,2 396 280 2900-3599 1120 5300 2120 1520 750 2,2 451 315 3600-4499 1250 5550 2250 1650 750 2,2 522 355 4500-5699 1400 5650 2400 1800 750 2,2 598 400 5700-7199 1600 5700 2600 2000 750 5,5 709 450 7200-8999 1800 5650 2800 2200 750 5,5 824 500 9000-11099 2000 5900 3000 2400 750 7,5 910 560 11100-13999 2240 6000 3240 2640 750 7,5 1057 630 14000-17699 2500 6000 3500 2900 750 7,5 1238 710 17700-22399 2800 6500 3800 3200 750 7,5 1604 Table 6. Technical characteristics ВМ-2 Diameter Consumptio D H a b c Pump Weight Dn, mm Q, m³/h mm mm mm mm mm Р, kw m1, kg 160 800-1199 560 4300 1560 1050 750 1,1 199 180 1200-1499 560 4300 1560 1050 750 1,1 200 200 1500-1899 560 4300 1560 1050 750 1,1 200 224 1900-2299 650 4350 1650 1050 750 1,1 224 250 2300-2899 710 4350 1710 1100 750 1,1 247 280 2900-3599 800 4300 1800 1200 750 2,2 274 315 3600-4499 900 4550 1900 1300 750 2,2 319 355 4500-5699 1000 4650 2000 1400 750 2,2 350 400 5700-7199 1120 5200 2120 1520 750 2,2 444 450 7200-8999 1250 5150 2250 1650 750 2,2 494 500 9000-11099 1400 5400 2400 1800 750 2,2 578 560 11100-13999 1600 5500 2600 2000 750 5,5 665 630 14000-17699 1800 5500 2800 2200 750 5,5 773 710 17700-22399 2000 6000 3000 2400 750 7,5 944 800 22400-28399 2240 6350 3240 2640 750 7,5 1108 900 28400-35599 2500 6350 3500 2900 750 7,5 1264 1000 35600-44099 2800 7100 3800 3200 750 7,5 1629 17
2.2 Venturi scrubber The company UralActiv Ltd. manufactures Venturi scrubber from thermoplastic materials. Polypropylene and polyethylene are main polymeric materials that are used in production. The advantages of these materials in comparison with steel are high resistance to abrasion and corrosion cracking that provides long service life of equipment. Venturi scrubber is a device for effective particulate control of air passing through this device. This is a system for cleaning of ventilated gas from impurities, for returning of gas into the atmosphere or into the next production. One can used the usual process water as an absorbing agent. This water doesn t need preliminary preparation and therefore it cheapens the working of gas treatment system maximally. Area of application Venturi is a scrubber suitable for any production with emissions of contaminated air such as: coke and by-product process; refinery operations; stone-working process; chemical production; metallurgical production etc. Operation principle of Venturi scrubber: The capture principle bases on settling of dust particles on the drops of irrigating water in the Venturi pipe and their next separation in the scrubber. Dusty gases that get into the Venturi pipe are irrigated with water and are accelerated to the speed 40-150 m/s in a confuser. Drops of irrigating water are disintegrated with rapid gas stream and are accelerated in the throat of Venturi pipe. Because the water density is three times greater than the gas density, water drops have lower speed and as a result the filtration of dusty gas stream goes through moving water fine-filter. In this filter the gravity sedimentation of dust particles from the gas is happen on granular drops. Drops with sedimented dust particles are caught in the scrubber due to the centrifugal force, are settled and are removed through the hydraulic lock from the device in form of slurry. 18
Proposed device for gas cleaning has high possibility of capture. The present Venturi scrubber is designed to clean from: soot and dusty particulate matters; resinous compounds and chlorinates; hydrogen sulphide and ammoniac vapors; dioxides and acids. 19
3. Fibrous filters FVG-PP-UA UralActiv Ltd. produces fibrous galvanic filters FVG-PP- UA which are similar to filters FVG-T and FVG-M. The filters FVG-PP-UA are intended to air ventilation emissions from the most hard-separable small aerosol particles, mists of acids, resinous and oily aerosols with particle loading at least 10 micron. Also the fibrous filters are used to filtrate mists of solutions within the chemical reactions by different work activities. The fibrous galvanic filters are widely used for air washing in systems of ventilation, supply ventilation, airconditioning and in other special equipment. The fibrous filters FVG-PP-UA fall in between wet scrubbing and filter devices. The casing of filter is made from chemical-resistant material polypropylene. The cassette with filtering material out on the frame is placed inside the casing. To check the filter condition there are inspection holes on the casing and visual level indicator. The filtering material is a polymeric fabric on basis of polypropylene. The material has purity class G-4 according to EN 779. The filter operates in a mode of accumulation of caught particles on the filtering material s surface with partial draining. If the pressure drop is 500 Pa (50 mm w.g.), the galvanic filter is exposed to periodic cleaning (one in 15-30 days). The cassette is easy to remove from the filter FVG-PP-UA. The advantage of cassette is its prefabricated structure which enables to change only filtering material and not the whole cassette. There are five types of filters with capability from 2500 till 80000 m3/h. Every type has three modifications: 01 without hydraulic lock, with two-side access 02 with hydraulic lock, with two-side access 03 with hydraulic lock and irrigation, right-hand and left-hand with two-side access. 20
Technical characteristics of fibrous galvanic filters Type of filter FVG-PP-UA-0.37-01 FVG-PP-UA-0.37-02 FVG-PP-UA-0.37-03 FVG-PP-UA-0.74-01 FVG-PP-UA-0.74-02 FVG-PP-UA-0.74-03 FVG-PP-UA-1.6-01 FVG-PP-UA-1.6-02 FVG-PP-UA-1.6-03 FVG-PP-UA-3.2-01 FVG-PP-UA-3.2-02 FVG-PP-UA-3.2-03 FVG-PP-UA-6.4-01 FVG-PP-UA-6.4-02 FVG-PP-UA-6.4-03 Air washing capacity, m3/h Square of filtering surface, m2 Aerosol concentration in a gas to be clean, mg/m3, (max) Hydraulic resistance, Pa (kgf/m2) Cleaning efficiency, % (min) 2500-5000 0,37 10 300-500 96 5000-10000 0,74 10 300-500 96 10000-20000 1,6 10 300-500 96 20000-40000 3,2 10 300-500 96 60000-80000 6,4 10 300-500 96 Weight, kg, (max) 27 30 30 33 36 36 56 59 59 76 80 80 150 153 153 Overall and mounting dimensions Type of filter L L3 H (max) H3 H4 H5 H6 B a b n C min FVG-PP-UA-0.37-01 1150-880 600 360 430-560 270 360-820 FVG-PP-UA-0.37-02 1150 240 1020 600 360-370 560 270 360 200 820 FVG-PP-UA-0.37-03 1150 240 1020 600 360-370 560 270 360 200 820 FVG-PP-UA-0.74-01 1110-880 600 610 430-810 440 440-820 FVG-PP-UA-0.74-02 1110 220 1020 600 610-370 810 440 440 200 820 FVG-PP-UA-0.74-03 1110 220 1020 600 610-370 810 440 440 200 820 FVG-PP-UA-1.6-01 1150-1100 820 855 540-1055 630 630-1040 FVG-PP-UA-1.6-02 1150 240 1240 820 855-480 1055 630 630 200 1040 FVG-PP-UA-1.6-03 1150 240 1240 820 855-480 1055 630 630 200 1040 FVG-PP-UA-3.2-01 1410-1100 820 950 540-1150 820 950-1040 FVG-PP-UA-3.2-02 1410 370 1240 820 950-480 1150 820 950 200 1040 FVG-PP-UA-3.2-03 1410 370 1240 820 950-480 1150 820 950 200 1040 FVG-PP-UA-6.4-01 1670-1925 1645 1710 950-1910 1300 1300-1865 FVG-PP-UA-6.4-02 1670 500 2065 1645 1710-890 1910 1300 1300 200 1865 FVG-PP-UA-6.4-03 1670 500 2065 1645 1710-890 1910 1300 1300 200 1865 21
FVG-PP-UA -01 FVG-PP-UA -02 22
FVG-PP-UA -03 23
UralActiv Ltd., office 304, ul. Manevrovaya 9, 620050 Yekaterinburg, Russia +7 (343) 253-10-21, 344-34-45, fax +7 (343) 344-34-46, info@uralactiv.ru, http://www.uralactiv.ru