Freestanding Treatment Console Installation pplies to Models: FTC4472 FTC4452 Special Tools: Level 3/8 masonry drill bit 9/32 wood drill bit Hammer drill This Midmark casework unit must be connected to a dedicated circuit rated 20, 120 VC. Failure to comply could result in an overload of the electrical circuit and/or components. ll electrical and plumbing connections must be made by a licensed electrician and plumbing contractor following applicable local, city, and national codes. Midmark casework unit contains four electrical duplex outlets, which are rated at a combined 15 amps. This rating must be taken into account when plugging device(s) into the available outlets. Inspect all components for shipping damages. concealed damage report must be filed with the carrier (by the person recieving the goods) within 15 days of delivery. 2113i 2009 Midmark Corp. 60 Vista Drive Versailles, OH 45380 US 1-800-643-6275 1-937-526-3662 1 003-1890-00 Rev. D (1/12)
Floor Layout (as applicable). The floor layout. : Full size Floor Template and Wall Template are available upon request, or refer to rough-in dimensions on next page. B. Have licensed electrical and plumbing contractors position and install electrical outlet receptacles and related plumbing using the pre-installation template or layout. : Be sure floor construction is sufficient to adequately support / anchor the casework unit. If necessary, contact a licensed contractor to reinforce the floor. 3/4" (1.9 cm) 1/2" (1.3 cm) NPT 2.5" (6.4 cm) (max.) 2" (5.1 cm) (min.) 5/8" (1.6 cm) O.D. 2.5" (6.4 cm) (max.) 2" (5.1 cm) (min.) Wall 2-7/8" (7.3 cm) 3-1/16" (7.8 cm) 3-1/16" (7.8 cm) 10-7/8" (27.6 cm) Top View of Base 12-3/8" (31.4 cm) 10-7/8" (27.6 cm) Vacuum Supply 22-5/8" (57.5 cm) 21" (53.3 cm) Electrical Supply Electrical Terminal Box ir Supply 16-1/2" (41.9 cm) 120 VC / 20 mp / 60 Cycle 3-wire, Dedicated Circuit Secure Terminal Box to cabinet after electrical supply is connected Water Supply Left Side Plumbing Rough-In Perimeter Right Side Plumbing Rough-In Perimeter Front 2-3/8" (6.0 cm) 42-1/2" (108 cm) 44-1/4" (112.4 cm) 7/8" (2.2 cm) 2
Wall Layout (as applicable) 44-3/8" (112.7 cm) 3-1/4" (8.3 cm) 31-1/8" (79.1 cm) 3-1/4" (8.3 cm) 10" (25.4 cm) 3" (7.6 cm) 10" (25.4 cm) 3" (7.6 cm) 10" (25.4 cm) 15" (38.1 cm) Left Side Plumbing Rough-In Perimeter Center Rough-In Perimeter Right Side Plumbing Rough-In Perimeter Left Side Plumbing Rough-In Perimeter Center Rough-In Perimeter Right Side Plumbing Rough-In Perimeter 4-1/4" (10.8 cm) 8-3/8" (21.3 cm) Floor 42-1/2" (108 cm) 44-1/4" (112.4 cm) 1-1/16" (2.7 cm) 7/8" (2.2 cm) 3
Setting Up If applicable, refer to 2 Drawer Removal on next page as removal is different.. If necessary, remove the drawers by pulling the drawer outward until it meets resistance. B. On both sides of drawer, pull outward until locking slots (1) on drawer are free of tabs (2) on drawer glides (3). C. Lift drawer upward (4) while pulling outward to free rear of drawer from hooks (5) on glide. D. On base sections that have doors, open door and remove bottom shelf. 4 When reinstalling drawers assure back of drawer is positioned beneath hooks (4) on glides and tabs (2) on glide snap into locking slots (1) on drawer. 1 5 3 2 D2116i 4
Removing the 2 (5 cm) Drawer: To remove drawer and front slide.... While lifting or pushing down release levers (on each side), slide rail and drawer from slide. To remove drawer tray and front... B. Remove four screws, then slide drawer tray and front from channel. To remove slides... C. Remove four screws, then remove slides. D134900i 5
Side Storage Unit You must remove the bottom panel, to install the anchor mounting clips.. Open the doors and lift out the bottom panel. D2128i 6
Locating nchor Mounting Clips. Place the anchor mounting clips within 4 (10 cm) of each corner. Be sure clips do not interfere with the leveling bolts. [suggested locations of the four mounting clips]. The hold-down bolts for the anchors should be placed as close as possible to the sub-base lip. nchor Mounting Clip B. Using the anchor mounting clips as templates, place location marks for the hold-down bolts on the floor. 42.5" (108 cm) 4 in. (10 cm) maximum 4 in. (10 cm) maximum 21" (53.3 cm) 4 in. (10 cm) maximum 4 in. (10 cm) maximum 7
Installing nchor Mounting Clips & Leveling nchor Mounting Clip. Using the appropriate drill bit (masonry: 3/8 ) (wood: 9/32 ), drill holes at each location per specification. B. Loosely install the anchor mounting clips. Sub-base 9/32 diameter Sub-base C. Using a 1/4 socket, adjust leveling screws in each corner until cabinet is level. To prevent instability, do not adjust leveling screws more than 1/2 (1.3 cm). 2 (5.1 cm) Concrete 3/8 diameter Non-Concrete D. Insert shims beneath area of anchor and tighten each bolt. E. Trim any excess shim material that may protrude beyond base. Shim Lower Raise 1/2 (1.3 cm) maximum 8
Securing Electrical Box. Secure the electrical box to the inside of the cabinet base with (#10 x 3/8 ) screws. Screws 2207i 9
Installing Overhead Section (if required). Remove side panels and receptacle enclosure covers. B. Position overhead section on top of midsection. Be sure to align mounting holes. B C. Connect the plugs from the overhead section and midsection. D. Secure overhead section to midsection with six 10-24 x 5/8 screws. F C E. Install the receptacle enclosure and side panels. Equipment lert The particle board screws must be installed for stability. E F. Remove task light cover to access holes in upper unit by taking out thumb screws. D. Install particle board screws. E D2124i 10
Installing Clock / Timer. Remove clock / timer from box located in cabinet and push clock / timer into opening. Installation of Power Supply for Clock / Timer (if required) B. Plug power supply to electrical outlet. F C. Install grommet into upper cabinet. D. Route power supply wire through cabinet. C E. If necessary, install grommet into task light cover. F. Plug power supply cord into the back of the clock / timer. D E B D2215i 11
Removal of ccessory Panel. Remove side panels and then pull out on accessory panel. Side Panel Relocating Pull-out Shelf and Swing-out Shelf or Tub B. Remove six screws from shelf slides and relocate pull-out shelf in desired position. C. Loosen screws so the shelf or tub is loose. D. Move shelf forward to remove. Remove screw, then re-install at desired location (do not tighten). Position shelf, then tighten screw. Side Panel D Shelf Slide B C D2216i 12
Installing and djusting Doors / Panels / Shelves. Check doors for proper adjustment. [ap between doors should be approximately 1/16 (0.16 cm)]. Refer to Hinge djustments for proper adjustment procedures. B. Install shelf brackets at desired height of shelf. D2129i B 13
Hinge djustments. Side djustment Turn screw () until door is in desired position. B. Height djustment Loosen screw (B) approximately 1/4 turn, reposition door, then tighten screw. C. Depth djustment Loosen screw (C), reposition door, then tighten screw. C B Base Doors Upper Doors B Bi-Fold Doors B C Base Doors B Figure 12 C 14
Freestanding Treatment Console (FTC-4472) Optional Task Light Equipment lert Dedicated branch circuit rated at 120VC, 50/60 Hz, 20 amp. BLLST REEN RN/YEL Only Licensed Electricians following local and applicable electrical codes should install and connect the electrical supply power. Midmark cannot be held responsible for installations that do not conform to local codes. Mid Section of 12:00 Unit RN/YEL 1 1 2 2 REEN/YELLOW 3 3 REEN/YELLOW /Y REEN/YELLOW RN/YLW RESET TEST REEN/YELLOW /Y REEN REEN REEN L N REEN/ YELLOW RN REEN/YELLOW 1 2 3 1 2 3 REEN/YELLOW REEN 3 2 1 3 2 1 /Y 3 2 1 3 2 1 REEN User Electrical Connections REEN/ YELLOW D2195i 15
Freestanding Treatment Console (FTC-4452) Equipment lert Dedicated branch circuit rated at 120VC, 50/60 Hz, 20 amp. Only Licensed Electricians following local and applicable electrical codes should install and connect the electrical supply power. Midmark cannot be held responsible for installations that do not conform to local codes. REEN REEN L N REEN/ YELLOW REEN REEN/ YELLOW D2196i 16