User s Manual and Operating Instructions

User s Manual and Operating Instructions Model Numbers: PT-18W-DDF-A, PT-20F-DDF-A, PT-20S-DDF, PT-24O-DDF, PT-24-DDF, PT-24-DDF-F, PT-30-DDF, PT-30P-DDF-A, PT-30P-DDF-AF READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the instructions in this manual before assembling, starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for future reference. CAUTION For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors. Never use the fan in spaces which contain products such as gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles, or any unknown chemicals. This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which regulates electric fan blade safety, and is certified under UL# E355088. Please note the serial number of your fan, and write it on the back of this User s Manual for future reference. 2013, Pinnacle Products International, Inc. 668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996 Fax: (215) 891-8461 Web: www.protemp.us Email: info@pinnacleint.com 9500450290-13

User s Manual and Operating Instructions Table of Contents Safety Information... 3 Notes Page...4 Troubleshooting Guide...19 Warranty...Back Cover 5 18 Wall Fan PT-18W-DDF-A 11 24 Barrel Fan PT-24-DDF PT-24-DDF-F 17-18 30 Pedestal Fan PT-30P-DDF-A PT-30P-DDF-AF 6-7 20 Floor Fan PT-20F-DDF-A 12-13 24 Omni Fan PT-24O-DDF 8-10 20 Shop Fan PT-20S-DDF 14-16 30 Floor Fan PT-30-DDF 2013, Pinnacle Products International, Inc. 2 HVF Air Circulator User s Manual

Safety Information IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY, SERVICE OR USE OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN SERIOUS PERSONAL INJURY AND / OR PROPERTY DAMAGE. THIS IS A FAN - NOT A TOY! TO REDUCE THE RISK OF PERSONAL INJURY AND ELECTRIC SHOCK, FANS SHOULD NOT BE PLAYED WITH OR PLACED WHERE SMALL CHILDREN CAN REACH IT. To guard against electric shock while operating, do not allow fan to come in contact with other grounded objects such as pipes, radiators, etc. Risk of fire, electric shock, or personal injury when performing service or maintenance. Unplug or disconnect the fan from the power supply before servicing. CAUTION Automatically Operated Device - To Reduce The Risk Of Injury Disconnect From Power Source Before Servicing To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid- State Speed Control Device. To Reduce The Risk Of Electric Shock And Injury To Persons, Do Not Use In a Window. To Reduce The Risk Of Electric Shock, Do Not Expose To Water Or Rain. This unit is designed for indoor use only. Installation work and electrical wiring must be done by qualified person (s) in accordance with all applicable codes and regulations. When servicing or replacing a component requires the removal or disconnection of a safety device, the safety device is to be reinstalled or remounted as previously installed before operating this fan. Use this fan only in the manner intended by the manufacturer. If you have any questions, contact Customer Service at 800-641-6996. - Before operating always check fan for loose or damaged parts. Inspect power cord for any damage. Never use fan if any parts are damaged or missing. Never use fan without safety guards attached. - Operate only on 120 volt 60 Hz (cycle) current with a minimum of a 15 amp circuit. - When used with an extension cord, use only cord of proper size (Amp rating), UL listed, and with receptacle to accept three prong grounded plug furnished on the fan s power cord. Always keep power cord and extension cords away from heat, oil, and sharp edges. Inspect cords periodically and replace if damaged. 2013, Pinnacle Products International, Inc. 3 HVF Air Circulator User s Manual

NOTES 2013, Pinnacle Products International, Inc. 4 HVF Air Circulator User s Manual

Wall Mount Installation 1. Attach fan to wall or ceiling using Upper Bracket (Item #6). 2. Be sure Upper Bracket (Item #6) is attached to a suitable beam when hanging. Tools Needed: - 10mm Adjustable Wrench. Exploded View 18 WALL FAN: PT-18W-DDF-A The installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 50 pounds continuously. 1 2 3 4 5 6 7 8 9 10 11 12 17 16 15 14 18 13 Figure 1: Exploded View of PT-18W-DDF-A Replacement Parts 1 Logo Plate 95-043-0370 2 Front Guard 95-032-0150 3 4 5 6 Fan Blade Assembly Upper Bracket 95-003-0606 95-061-0100 7 Rear Guard 95-032-0250 8 Motor 95-030-0515 9 Switch Holder 95-031-0300 10 Switch Gasket 95-031-0340 11 Switch (Chain) 95-031-0110 12 Switch Cover 95-031-0500 13 Cord Bushing 95-026-0160 14 Pivot Washer 95-024-0300 15 Swivel Spacer 95-050-0185 16 Pivot Screw 95-024-0310 17 Capacitor 95-004-0215 18 Power Cord 95-026-0230 2013, Pinnacle Products International, Inc. 5 HVF Air Circulator User s Manual

20 FLOOR FAN: PT-20F-DDF-A Installation and Assembly 1. Remove 1 screw from each Frame Support L and R (Items #7* and #19*). 2. Slide Frame Support L and Frame Support R into Support Frame (Item #21*) and line up holes for screw. 3. Re-attach screw to Frame Support L and Frame Support R. 4. Place the fan on level ground in a safe, desired position then connect to an approved power source. Tools Needed: - Phillips head screwdriver. -10 mm adjustable wrench. 20 FLOOR FAN - OPTIONAL WALL MOUNT Wall Mount Installation 1. Attach wall mount to stud (Item #24*) 2. Attach Lower Support Frame (Item #21*) to the Wall Mount (Item #24*) by replacing rear part of Lower Support Frame into hook of Wall Mount and resting front and rear feet of fan (Items #17* and #18*) onto the wall. * On Page 7 The installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 50 pounds continuously. NOTE: Fan must be mounted to wall so that both feet are positioned against the wall surface. Mounting this fan to a bare stud without both fan feet positioned against a flat surface will result in damage to the fan. Figure 2: Wall Mount Installation Figure 3: Wall Mount Installation - Close Up 2013, Pinnacle Products International, Inc. 6 HVF Air Circulator User s Manual

20 FLOOR FAN CONTINUED Exploded View 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 23 21 20 19 18 17 24 22 Figure 4: Exploded View of PT-20F-DDF-A Replacement Parts 1 Logo Plate 95-043-0405 2 Front Guard 95-032-0160 3 4 5 6 Fan Blade Assembly Frame Washer 95-003-0616 95-024-0250 7 Frame-Support L 95-024-0265 8 Main Circle Tube 95-024-0280 9 Top Washer 95-024-0290 10 Rear Guard 95-032-0260 11 Motor 95-030-0525 12 Switch Holder 95-031-0310 13 Switch 95-031-0120 14 Switch Cover 95-031-0510 15 Cord Bushing 95-026-0165 16 Control Knob 95-027-0110 17 Front Foot 95-023-0220 18 Rear Foot 95-023-0230 19 Frame-Support R 95-024-0275 20 Swivel Spacer 95-050-0180 21 Lower Support Frame 95-024-0245 22 Power Cord 95-026-0240 23 Capacitor 95-004-0225 24 Wall Mount Kit 95-078-0100 2013, Pinnacle Products International, Inc. 7 HVF Air Circulator User s Manual

20 SHOP FAN: PT-20S-DDF Installation and Assembly 1. Remove Knob Screw (Item #15*) and Wing Nut (Item #14*) from top of Post. 2. Slide Connector Bracket (Item #4*) onto top of post. 3. Line up holes on the Post and Connector Bracket (Item #4*). 4. Re-insert the Knob Screw (Item #15) through the Post and Connector Bracket (Item #14*) and tighten firmly with the Wing Nut (Item #14*). Tripod Operation Instructions Tripod Leg Operation 1. Fold legs out and slide support bracket to center of leg. 2. To adjust leg height; rotate locking ring clockwise to loosen. NOTE: Keep a firm grip on the tripod while leg is unlocked! The leg will collapse into itself unless held tightly. NOTE: Be certain to make all three legs the same height. Setting legs to different heights will make the fan unbalanced and COULD FALL OVER. 3. Slide leg extension to desired height. 4. Rotate locking ring counter-clockwise and tighten firmly. Be sure the leg is secure before moving to next leg. 5. Repeat steps 2-4 for remaining legs. 5. Place the fan on level ground in a safe, desired position then connect to an approved power source. 6. Set desired tripod stand height following Tripod Operation Instructions below. * On Page 10 TRIPOD CENTER POST OPERATION 1. To change the post height; rotate locking ring counter-clockwise to unlock post. NOTE: Be certain to keep a firm grip on post while unlocked! The fan will slide down to its lowest point if it is not held and slowly moved to desired position. 2. Raise or lower post to desired position. 3. Rotate locking ring clockwise to lock post and tighten firmly. DO NOT MOVE OR ADJUST FAN WHILE IN OPERATION. THIS CAN CAUSE DAMAGE TO FAN AND INJURY TO THE OPERATOR. OPTIONAL CEILING MOUNT Installation and Assembly 1. Attach Ceiling Mounting Kit (Item #16*) to 2x4 stud that is able to support 50 lbs continuously using M6x40mm screw. (See Figure 5**) The installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 50 pounds continuously. 3. Be Certain that the Safety Pin lines up with the groove on the Connector Bracket (Item #4). (See Figure 6**) 2. Slide Connector Bracket (Item #4*) onto Ceiling Mounting Post. (See Figure 7**) 4. Rotate the entire fan so the safety pin locks into place and the holes on the Mounting Post line up with the holes on the Connector Bracket (Item #4*). (See Figure 8**) 5. Insert the Knob Screw (Item #15*) through the Mounting Post and Connector Bracket (Item #4*) and tighten firmly with the Wing Nut (Item #14*). (See Figure 8**) * On Page 10 ** On Page 9 2013, Pinnacle Products International, Inc. 8 HVF Air Circulator User s Manual

20 SHOP FAN CONTINUED - OPTIONAL CEILING MOUNT Figure 5: Optional Ceiling Mount Figure 6: Optional Ceiling Mount Figure 7: Optional Ceiling Mount Figure 8: Optional Ceiling Mount 2013, Pinnacle Products International, Inc. 9 HVF Air Circulator User s Manual

20 SHOP FAN CONTINUED Exploded View 1 2 3 4 5 6 7 8 9 10 11 13 14 15 12 Figure 9: Exploded View of PT-20S-DDF 16 Replacement Parts 1 Logo Plate 95-043-0420 2 Front Guard 95-032-0185 3 Fan Blade Assembly 95-003-0616 4 Frame 95-001-0500 5 Rear Guard 95-032-0285 6 Motor 95-030-0525 7 Switch Holder 95-031-0335 8 Power Cord 95-026-0270 9 Power Switch 95-025-0600 10 Capacitor 95-004-0250 11 Bushing 95-026-0180 12 Switch Cover 95-031-0540 13 Tripod 95-040-0100 14 Wing Nut 95-075-0400 15 Base Knob 95-015-0220 16 Ceiling Mount Kit 95-078-0300 2013, Pinnacle Products International, Inc. 10 HVF Air Circulator User s Manual

24 BARREL FAN: PT-24-DDF, PT-24-DDF-F Installation and Assembly 1. Fully expand Pipe Frame (Item #20) open, and tighten Frame Brackets (Items #21 and #22) with attached bolt. Exploded View 2. Place the fan on level ground in a safe, desired position then connect to an approved power source. NOTE: This model CAN NOT be wall mounted. Figure 10: Exploded View of PT-24-DDF / PT-24-DDF-F Replacement Parts 1 Logo Plate 95-043-0410 2 Front Guard 95-032-0170 3 4 Fan Blade Assembly 95-003-0621 5 6 Rubber Washer A 95-077-0100 7 Rubber Washer B 95-077-0110 8 Barrel 95-001-0300 9 Handle 95-006-0210 10 Rear Guard 95-032-0270 11 Motor 95-030-0530 12 Switch Holder 95-031-0320 13 Switch 95-031-0130 14 Cord Bushing 95-026-0170 15 Switch Cover 95-031-0520 16 Control Knob 95-027-0120 17 Power Cord 95-026-0250 18 Capacitor 95-004-0230 19 Foot 95-023-0210 20 Pipe Frame L/R 95-009-0500 21 Frame Bracket A 95-009-0510 22 Frame Bracket B 95-009-0520 23 Wheel Bolt 95-008-0310 24 Wheel 95-008-0110 2013, Pinnacle Products International, Inc. 11 HVF Air Circulator User s Manual

24 OMNI DIRECTIONAL FAN: PT-24O-DDF Installation and Assembly 1. Place the fan on level ground in a safe, desired position then connect to an approved power source. Exploded View 1 2 3 4 5 6 7 8 9 10 11 12 15 13 14 16 19 17 18 20 31 30 Figure 11: Exploded View of: PT-24O-DDF Replacement Parts 1 Front Guard 95-032-0170 2 Fan Barrel 95-001-0400 3 Power Knob 95-027-0130 4 Power Knob Holder 95-031-0325 5 Capacitor 95-004-0235 6 Power Cord 95-026-0255 7 Motor 95-030-0535 8 Motor Mount Assembly 95-030-0555 9 Motor Cooling Fan 95-030-0556 10 Fan Blade Assembly 95-003-0621 11 Rear Guard 95-032-0275 12 Front Leg 95-009-0600 13 Horizontal Adj. Knob 95-015-0150 14 Spacer 95-050-0200 15 Outer Ring Frame 95-024-0320 29 28 27 26 25 22 24 23 16 Vertical Adj. Knob 95-015-0150 17 Wall Mount 95-078-0200 18 Handle Pad 95-007-0100 19 Spacer 95-050-0200 20 Handle Arm 95-006-0300 21 Rear Leg 95-009-0610 22 Large Base Cap 95-024-0410 23 Large Base 95-024-0400 24 Foot Pad 95-023-0240 25 Wall Bracket - L 95-077-0100 26 Wall Bracket - R 95-077-0110 27 Small Base 95-024-0500 28 Small Base Cap 95-024-0510 29 Wheel 95-004-0155 30 Lower Mount 95-024-0325 31 Logo Plate 95-043-0331 21 2013, Pinnacle Products International, Inc. 12 HVF Air Circulator User s Manual

Wall Mount Installation 24 OMNI FAN - OPTIONAL WALL MOUNT 1. Attach Wall Mount (Item #17*) to wood stud as shown below. 2. Slide Wall Bracket L (Item #25*) and Wall Bracket R (Item #26*) on Large Base (Item #23*) onto Wall Mount. * On Page 12 The installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 105 pounds continuously. Tools Needed -Flat head Screw Driver. Wall Mount (Item #17*) 2 x4 STUD Figure 12: Wall Mount installation Close Up Handle Arm (Item #20*) Wall Large Base (Item #23*) Wall Mount (Item #17*) Figure 13: Wall Mount installation 2013, Pinnacle Products International, Inc. 13 HVF Air Circulator User s Manual

Installation and Assembly 1. Place the fan on level ground in a safe, desired position then connect to an approved power source. 30 FLOOR FAN: PT-30-DDF NOTE: This fan uses a folding wheel design. For quick assembly, simply swing the wheels out and snap to lock in place. Exploded View 7 8 9 10 15 16 17 25 19 11 18 21 22 23 1 2 4 5 6 20 24 25 Figure 14: Exploded View of PT-30-DDF Replacement Parts Item# Description Part Number 1 Front Guard 95-032-0140 2 Front Swivel Bracket 95-050-0100 3 Fan Blade Assy 95-003-0501 4 Motor 95-030-0500 5 Frame Foot 95-023-0200 6 Cart Frame 95-009-0400 7 Swivel Cover 95-050-0106 8 Frame Swivel Bracket 95-050-0111 9 Frame Upper Swivel Latch 95-050-0120 10 Swivel Latch Pin 95-050-0131 11 Frame Cap 95-011-0300 12 Wheel 95-008-0165 3 12 13 14 Item# Description Part Number 13 Wheel Axle 95-008-0260 14 Wheel Frame 95-008-0500 15 Upper Swivel Housing 95-050-0141 16 Frame Lower Swivel Latch 95-050-0150 17 Latch Spring 95-060-0155 18 Lower Swivel Housing 95-050-0161 19 Rear Guard 95-032-0240 20 Rear Swivel Bracket 95-050-0170 21 Capacitor 95-004-0200 22 Power Switch 95-025-0500 23 Rear Motor Cover 95-048-0100 24 Power Cord 95-026-0150 25 Guard Screw 95-033-0225 2013, Pinnacle Products International, Inc. 14 HVF Air Circulator User s Manual

30 FLOOR FAN - OPTIONAL CEILING MOUNT Ceiling Mount Installation MOUNTING BRACKET INSTALLATION: 1. Remove Wheel Frame (Item #15) 2. Attach Cart Frame to Ceiling beam using U-bolts (Item #5). 3. Assemble and attach Ceiling Mount Assembly as shown in Figure 15 below. Tools Needed - Phillips and flat head screw driver. - 10 mm adjustable wrench. Ceiling Kit Exploded View The installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 105 pounds continuously. This 30 Floor Fan (PT-30-DDF) is approved for use with California s BAR-97 Emissions Inspection System and meets all BAR-97(EIS) required specifications and standards 3 2 4 5 1 6 7 8 9 Figure 15: Exploded View of PT-30-DDF (ceiling mount kit) Ceiling Kit Replacement Parts Item# Description Part Number 1 Safety Cable Assy 95-060-0100 2 Nut for Ceiling Swivel Pin 95-060-0180 3 Nut 95-060-0125 4 Upper Ceiling Bracket 95-060-0110 5 U-Bolt 95-060-0120 Item# Description Part Number 6 Top Washer 95-060-0120 7 Lower Ceiling Bracket 95-060-0160 8 Tapping Screw 5-15mm 95-060-0195 9 Ceiling Swivel Pin 95-060-0170 2013, Pinnacle Products International, Inc. 15 HVF Air Circulator User s Manual

30 FLOOR FAN - OPTIONAL CEILING MOUNT CONTINUED Ceiling Mount Installation SAFETY CABLE INSTALLATION: 1. After the fan is securely mounted, feed the safety cable between one of the swivel brackets as shown in Figure 15. 2. Pull safety cable through and secure cable with safety cable U-bolt as shown in Figure 17. 3. Take other end of cable and wrap around beam 4. Secure cable loop as shown in step 2. Be sure there is approximately 2 inches of slack in the safety cable once both ends are secured. 5. Repeat on other side of fan so there are two safety cables. Tools Needed - Phillips and flat head screw driver. - 10 mm adjustable wrench The installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 105 pounds continuously. Figure 16: Safety Cable Installation Figure 17: Safety Cable Installation - Close Up 2013, Pinnacle Products International, Inc. 16 HVF Air Circulator User s Manual

Installation and Assembly Tools Needed: Pliers Phillips head screwdriver Flat head screwdriver 10mm / adjustable wrench 6mm hex wrench (included) Parts Included In Box: (1) Rubber Base Ring (1) Base (1) Front Guard (1) Rear Guard (1) Motor Assembly (1) Fan Blade Assembly (1) Spring (1) Support Pole Assembly Machine Screw Pivot Bolt Tilt Adjustment Knob 30 PEDESTAL FAN: PT-30P-DDF-A, PT-30P-DDF-AF Motor Assembly Motor Support Assembly Wing Nut Nut Upper Support Pole 1. Attach Rubber Base Ring (Item #16*) to outer edge of Base (Item # 5*). Be sure ribbed side of Base Ring is facing down. 2. Remove 5 screws from Flange on bottom of Lower Support Pole (Item #13*). 3. Completely extend Upper Support Pole (Item #21*) from Lower Support Pole and insert Spring into bottom of Lower Support Pole. 4. Attach Support Pole Assembly to Base. Tighten hardware using star pattern to insure a tight, uniform fit. 5. Stand assembly on Base, and press down Upper Support Pole and then tighten Height Adjustment Knob (Item #3*). 6. Attach Motor Support Assembly to Motor Assembly (see Figure 18). 7. Place Motor Support into Upper Support Pole. - Insert Pivot Bolt and tighten. - Insert Tilt Adjustment Knob and tighten. 8. Remove 4 screws on motor, and attach the Rear Guard. Tighten screws only after all 4 screws are reattached to the motor. 9. Remove the screws on the Motor and attach the Rear Guard onto groove in motor shaft, and replace screws (See Figure 19). 10. Loosen the set screw on the back of the Fan Blade Assembly and slide onto the motor shaft. 11. Position set screw over flat groove on motor shaft an tighten set screw using 6mm hex wrench (included). Be CAUTION Do NOT slide fan blade screw beyond the groove on the shaft! This will cause the fan blade to not spin properly and can cause damage to your fan! Be sure that fan shaft is flush with front of fan blade assembly. Figure 18: Attaching Motor to Motor Support Assembly Rear Guard Motor Figure 19: Attaching Rear Guard to Motor sure set screw is on the groove, and the front of Fan Blade Assembly is flush with front of shaft before tightening. 12. Attach Front Guard by first aligning the top hooks of the Front Guard onto the top of the Rear Guard edge. Work your way around the Guard, placing the Front Guard hooks over the Rear Guard edge. If necessary, use a flat head screwdriver to help pry the Front Guard hooks over the Rear Guard edge. Continue until all hooks are completely attached to the Rear Guard edge. NOTE: This model CAN NOT be wall mounted * On Page 18 2013, Pinnacle Products International, Inc. 17 HVF Air Circulator User s Manual

Exploded View 30 PEDESTAL FAN 4 5 6 9 8 23 2 7 1 22 11 3 10 12 13 17 19 Figure 20: Exploded View of PT-30P-DDF-A / PT-30P-DDF-AF Replacement Parts 15 16 14 1 Logo Plate 95-043-0340 2 Front Guard 95-032-0181 3 Height Adjustment Knob 95-015-0205 4 5 6 7 Fan Blade Assembly Power Switch (Chain) 95-003-0631 95-031-0140 8 Motor Assembly 95-030-0545 9 Rear Guard 95-032-0281 10 Height Adjust. Knob Nut 95-015-0215 11 Pipe Ring 95-017-0215 12 Pipe Support 95-017-0220 18 21 20 13 Lower Support Pole 95-017-0205 14 Latch Spring 95-060-0210 15 Upper Base 95-024-0225 16 Lower Base (Rubber Base Ring) 95-024-0235 17 Motor Support 95-030-0560 18 Left Support 95-030-0570 19 Right Support 95-030-0575 20 Tilt Adjustment Knob 95-015-0210 21 Upper Support Pole 95-010-0305 22 Power Cord 95-026-0260 23 Capacitor 95-004-0240 2013, Pinnacle Products International, Inc. 18 HVF Air Circulator User s Manual

Troubleshooting Guide Problem Possible Cause Corrective Action Fan does not operate Reduced Air Flow Humming sound but no operation Excess Noise (vibration, squealing) 1. No power 2. Bad motor Replace motor 1. Obstruction 2. Bad switch or capacitor 1. Bad capacitor Replace capacitor Inspect power cord for damage. Be sure unit is plugged in and turned on. Turn off and unplug fan. Remove guard and make sure nothing is obstructing the fan blades. Replace switch or capacitor (Note: To prolong life of fan, operate fan first in 1(LOW) for 5-10 seconds before switching to higher speed. 1. Fan is not on level ground Turn off fan, and move unit to smooth level surface. 2. Guard is not secure Check guard screws to be sure all are tight. 2013, Pinnacle Products International, Inc. 19 HVF Air Circulator User s Manual

1 YEAR LIMITED WARRANTY Pinnacle Products International, Inc. warrants this product to the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided. Pinnacle Products International, Inc. requires reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should keep your sales slip, invoice, or cancelled check from the original purchase. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service within the warranty period, and which Pinnacle Products International, Inc. shall determine at its reasonable discretion. This warranty does not apply to products purchased for rental use. This Limited Warranty does not cover replacement of belts or tightening of belts, or any failures or operating difficulties due to normal wear and tear, accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance and service by you or any third party. Failure to perform normal and routine maintenance on the fan, shipping damage, damage related to insects, birds, or animals of any kind, and damage due to weather conditions are also not covered. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase. All transportation costs for the return of the damaged product or parts will be the responsibility of the purchaser. Upon receipt of damaged item, Pinnacle Products International, Inc. will examine the item and determine if defective. Pinnacle Products International, Inc. will repair or replace and return the item, freight pre-paid. If Pinnacle Products International, Inc. finds the item to be in normal operating condition, or not defective, the item will be returned freight collect. This Limited Warranty is in lieu of all other express warranties. Pinnacle Products International, Inc. disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED WARRANTY EXPIRES, Pinnacle Products International, Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION. FURTHER, Pinnacle Products International, Inc. SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle Products International, Inc. assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to you. Pinnacle Products International, Inc. does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on Pinnacle Products International, Inc. Register Online at: www.protemp.us/product_registration.php Always be sure to specify model number and serial number when making any claim with Pinnacle Products International, Inc. For your convenience use the space provided below to list this information: Model #: Serial #: Date of Purchase: Pinnacle Products International, Inc. 668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996 Fax: (215) 891-8461 Web: www.protemp.us Email: info@pinnacleint.com