IST-07-11160 IST-07-11160/110 IST-07-11160/220 Electroimán retenedor de puertas 60kg Electromagnetic Door Holders IST-0711160 are attractively designed and ruggedly constructed. The contact plate can be adjusted to suit any door angle. Electromagnetic Door Holders have a minimum holding force of approximately 35/50kg and can hold most type of doors. In application, the device releases the door when signaled by the fire alarm system, which then allows the door closing mechanism to close the door. This unit also have a Manual Release Switch to release the door manually or to test the operation of the unit. Each unit has a built-in electronic circuit that is designed for better reliability and performance. Incorporation of manual release switch Residual magnetism release electronic circuit for instant release Wide angle rotateable contact plate High holding force Supply voltage Supply current Input power Holding force Net/Gross weight 24V DC 110VAC 220VAC 60 ma 1.5 W 35/60 Kg minimum 652/690 g SUITABLE FOR INDOOR APPLICATION
Rotulas de longitudes especiales para retenedores de puertas Standard Ref. IST-07-11160 IST-09-R033 Longitud: 280mm IST-09-R028 Longitud: 230mm IST-09-R025 Longitud: 200mm IST-09-R020 Longitud: 150mm
IST-07-1160 IST-09-R100 IST-09-11100
IST-07-10224/24/6 IST-07-10224/110/8 IST-07-10224/220/4 Campanas de Alarma de 4 /6 /8 Alarm bells are professionally designed to meet the needs of fire fighting and detection system with central control equipment. The simplicity of the design incorporates fewer working parts, easy installation and high level of efficiency, thus making the bells capable for operating under most adverse conditions. Alarm bells are designed to meet the requirements of BS5839 Part 1. Model IST-07-10224 Well proven high reliability Plug-in power supply Interchangeable base Wide operating voltage range Zero standby current Low current consumption Loud and clear ringing tone Universal application-available in three DC voltages 6V, 12V and 24V. AC voltages available in 110V and 220V for use with most alarm systems. DECIBEL LEVELS Is highly suitable for surface or semi-concealed fixing, which, in this case, means that the base of bell can be sunk into the wall using a junction box so that the edges of the bell are only 12mm from the wall surface. AC TYPE DECIBEL RATING AT 1M (3FT) Voltage Amps 100mm (4") 150mm (6") 200mm (8") 110 0.0155 92dB 95dB 97dB 220 0.033 98dB 105dB 106dB DC TYPE DECIBEL RATING AT 1M (3FT) Voltage Amps 100mm (4") 150mm (6") 200mm (8") 24 0.05 96dB 103dB 105dB Net/Gross Weight 626/668g 888/966g 1296/1445g SIRIM TEST REPORT 83LL129 (MODEL ) MOUNTING INSTRUCTIONS The bell must be mounted with its striker pointing downwards.
IST-08-108/1 IST-08-108/2 IST-08-108/1 Pulsador con llave de Test (1x NC,NO,C) IST-08-108/2 Pulsador con llave de Test (2x NC,NO,C) Manual Call Point is suitable for open or close circuit system and is professionally designed for use in fire detection systems with central control equipment. Alternative terminals are provided for open or close circuits. When wired for open circuit operation, the circuit closes instantly when the glass is smashed. Openings are provided for 3/4" O conduit entries from top, bottom and the back. The casings are moulded from specially selected engineering plastic, which comes in 5 different colours, with high impact strength, high resistance to heat. All metal parts are made of brass and phosphor bronze to ensure life long resistance against corrosion. A high realibility micro switch is also included. Double terminal wire connectors for independent input and output connections which facilitate installations when used in looping. Provision of thread protection plugs which protect the thread of the brass inserts on the base box when conceal fixing is necessary. Incorporation of the instant test operation which is activated by a special key provided. Size Current ratings 88mm X 88mm X 55mm 12/24V DC 10A 48V DC 3A (Optional) 250V AC 10A (Optional) Net/Gross weight 160/184g Connections TERMINAL Max 2.5mm² cable AUSTRALIAN STANDARD CERTIFICATE NO. 345 OPTIONAL FEATURES Is designed to meet the requirement of BS5839 Part 2 and approved by Australian Standard AS 1603 Part 5. RANGE OF CASING COLOURS White, Yellow, Green, Red, Blue Polycarbonate transparent protection cover Super bright light emitting didode (LED) Monitoring resistor Blocking diode Switch Choices - two single pole double throw (SPDT) micro switch. six terminal provided
IST-08-11824 IST-08-11824 Pulsador con llave de Test ( NC+NO) Manual Call Point IST-08-11824 is suitable for open or close circuit system and is professionally designed for use in fire detection systems with central control equipment. Alternative terminals are provided for open or close circuits. When wired for open circuit operation, the circuit closes instantly when the glass is broken. Cable knockout seals are provided for 3/4" D conduit entries from top, bottom and the back. The casings are moulded from specially selected engineering plastic, which comes in 5 different colours, with high impact strength, high resistance to heat. All metal parts are made of brass and phosphor bronze to ensure life long resistance against corrosion. Double terminal wire connectors for independent input and output connections which facilitate installations when used in looping. Instant test operation is available through activation utilizing a special key provided. Suitable for surface or flush mounting. Size (mm) Current ratings Net/Gross weight Connections 88 x 88 x 55 12/24V DC 10A 150/176g Terminal Max 2.5mm² cable RANGE OF CASING COLOURS OPTIONAL FEATURES Polycarbonate transparent protection cover Different range of casing colours white, yellow, green, red, blue Specific languages available on facial layout upon request. Blue, Green, Red, Yellow, White
IST-08-11524 Sirenas Is a versatile, compact electronic sounder that is designed ideally for fire, security and hazard warning. This solid-state sounder offers significantly high output levels at low current consumption. The casing is designed using a high grade ABS engineering plastic that has excellent resistance to impact and heat. Featuring a red polythene removable conduit plug for easy conduit entries, is designed to work effectively with most detection systems incorporating central control equipment. It also facilitates conceal fixing with the provision of thread protection plugs that prevent damage to the brass insert thread at the base of the box.perfectly combining performance and functionality, has a protection classification of IP 54 and is designed to meet the requirements of BS5839 Part 1:1980. Functional-Inherent design offers wide operating voltage range Efficiency-Low power consumption with high output Accessible-Removable conduit plug offers easy conduit entries Versatile-Suitable for surface or flush mounting Practical Design-Provision of thread protection plugs protect brass inserts when conceal fixing is necessary Compatible-Works perfectly well with most detection systems Dimensions current voltage frequency Sound output level temperature Approximate weight Protection classification Terminal capacity 88mm x 88mm x 43mm (75mm with base) Maximum 35mA at 24V DC 24V DC 600Hz - 2.5KHz 00± 3dB at 24V DC at 1m -10 C min to +60 C max 144 g IP 54 2 x 1.5mm² conductors