WIIN DIAAMS FM 58MVP VAIALE-APAIT NDENSIN AS FUNAE (have attached arrier single stage A & arrier Humidifier) Table 5 Electrical Data UNIT SIZE VLTS HETZ PHASE PEATIN VLTAE ANE Maximum* Minimum* MAXIMUM UNIT AMPS MINIMUM WIE SIZE MAXIMUM WIE LENTH (FT) MAXIMUM FUSE KT K AMPS** 040-14 115 60 1 127 104 8.9 14 31 15 060-14 115 60 1 127 104 8.9 14 31 15 080-14 115 60 1 127 104 8.9 14 31 15 080-20 115 60 1 127 104 13.8 12 32 20 100-20 115 60 1 127 104 13.8 12 32 20 120-20 115 60 1 127 104 13.8 12 32 20 * Permissible limits of voltage range at which unit will operate satisfactorily. Unit ampacity = 125 percent of largest operating component s full load amps plus 100 percent of all other potential operating components (EA, humidifier, etc.) full load amps. Length shown is as measured 1 way along wire path between unit and service panel for maximum 2 percent voltage drop. ** Time-delay type is recommended. FIELD 24-V WIIN FIELD 115-, 208/230-, 460-V WIIN FAT 24-V WIIN FAT 115-, 208/230-, 460-V WIIN 115-V SINLE PHASE 115-V FIELD-SUPPLIED DISNNET SWITH AUXILIA J-X FUNAE NTL ENTE FIVE WIE THEE-WIE HEATIN NL NTE 5 24-V TEMINAL LK W NTE 3 NTE 1 TW WIE THEMSTAT TEMINALS ND ND NDENSIN UNIT FIELD-SUPPLIED DISNNET ND ND 208/230-460-V THEE PHASE 208/230-V SINLE PHASE NTES: 1. onnect or terminal as shown for proper cooling operation. 2. Proper polarity must be maintained for 115-v wiring. 3. Use with 2-stage thermostat when zoning. 4. If any of the original wire, as supplied, must be replaced, use same type or equivalent wire. 5. Some thermostats require a "" terminal connection as shown. Fig. 21 Heating and ooling Application Wiring Diagram A98325 ELETI DISNNET SWITH PPE WIE NL ALTENATE FIELD LATIN FAT INSTALLED LATIN ALUMINUM WIE A93033 Fig. 22 Disconnect Switch and Furnace J-ox elocation 1. emove 2 screws holding auxiliary J-box. (See Fig. 23.) 2. otate J-box 180 and attach box to left side, using holes provided. Fig. 23 elocating J-ox A00212 20
WIIN DIAAMS FM 58MVP VAIALE-APAIT NDENSIN AS FUNAE (have attached arrier single stage A & arrier Humidifier) A00275 Fig. 39 Two-Stage Furnace with Single-Speed Air onditioner A00277 Fig. 41 Two-Stage Furnace with Single-Speed Heat Pump (Dual Fuel) A00276 Fig. 40 Two-Stage Furnace with Two-Speed Air onditioner A00278 Fig. 42 Two-Stage Furnace with Two-Speed Heat Pump (Dual Fuel) 39
WIIN DIAAMS FM 58MVP VAIALE-APAIT NDENSIN AS FUNAE (have attached arrier single stage A & arrier Humidifier) A00281 Fig. 45 Two-Stage Thermostat With Two-Stage Furnace and Two-Speed Air onditioner Fig. 43 Dual Fuel Thermostat with Two-Stage Furnace and Single-Speed Heat Pump A00279 See note 2 A00280 Fig. 44 Dual Fuel Thermostat With Two-Stage Furnace and Two-Speed Heat Pump A02348 Fig. 46 Single-Stage Thermostat With Two-Stage Furnace and Two-Speed Air onditioner 40
WIIN DIAAMS FM 58MVP VAIALE-APAIT NDENSIN AS FUNAE (have attached arrier single stage A & arrier Humidifier) Notes for Fig. 39-46: 1. Heat pump MUST have a high pressure switch for dual fuel applications. 2. efer to outdoor equipment Installation Instructions for additional information and setup procedure. 3. Select the ZNE position on the two-speed heat pump control. 4. utdoor Air Temperature Sensor must be attached in all dual fuel applications. 5. Dip switch No.1 on Thermidistat should be set in FF position for air conditioner installations. This is factory default. 6. Dip switch No. 1 on Thermidistat should be set in N position for heat pump installations. 7. Dip switch No. 2 on Thermidistat should be set in FF position for single-speed compressor operation. This is factory default. 8. Dip switch No. 2 on Thermidistat should be set in N position for two-speed compressor operation. 9. onfiguration ption No. 10 Dual Fuel Selection must be turned N in all dual fuel applications. 10. N connection should be made to the furnace terminal when using a Thermidistat. 11. ptional connection. If wire is connected, dip switch SW1-2 on furnace control should be set in N position to allow Thermidistat/Thermostat to control furnace staging. 12. ptional connection. If wire is connected, ADJ jumper on furnace control should be removed to allow Thermidistat/Thermostat to control outdoor unit staging. 13. Furnace must control its own high-stage heating operation via furnace control algorithm. This is factory default. 14. The VS Sensing terminal L should not be connected. This is internally used to sense defrost operation. 15. D NT SELET the FUNAE INTEFAE or ALANE PINT option on the two-speed heat pump control board. This is controlled internally by the Thermidistat/Dual Fuel Thermostat. 16. Dip switch D on Dual Fuel Thermostat should be set in FF position for single-speed compressor operation. This is factory default. 17. Dip switch D on Dual Fuel Thermostat should be set in N position for two-speed compressor operation. 41
WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) THEMIDISTAT HEAT STAE 2 HEAT STAE 1 L STAE 1 24 VA HT / 1/ TPIAL IL E AI NDITINE THEMIDISTAT L STAE 1 1/ HEAT STAE 2 HEAT STAE 1 L STAE 2 24 VA HT / TPIAL IL E AI NDITINE 1 2 24 VA MM 24 VA MM IDIF UTD SENS NNETIN D IDIFIE (24 VA) UTD SENS See notes 1, 6, 13, and 15 Fig. 2 Typical Fan oil With 1-Speed Air onditioner A97382 IDIF UTD SENS NNETIN D IDIFIE (24 VA) UTD SENS See notes 1, 6, 13, and 16 Fig. 3 Typical Fan oil With 2-Speed Air onditioner A97383 THEMIDISTAT VS LIN HEAT STAE 3 HEAT STAE 2 HEAT/L STAE 1 24 VA HT / 1/ TPIAL IL E THEMIDISTAT VS LIN HEAT/L STAE 1 HEAT STAE 3 HEAT/L STAE 2 24 VA HT / 1/ TPIAL IL E 1 2 24 VA MM 24 VA MM IDIF VS HEATIN UTD SENS NNETIN D IDIFIE (24 VA) UTD SENS See notes 1, 7, 14, and 15 Fig. 4 Typical Fan oil With 1-Speed Heat Pump A97384 10 IDIF VS HEAT UTD SENS NNETIN D IDIFIE (24 VA) UTD SENS See notes 1, 4, 5, 14, and 16 Fig. 5 Typical Fan oil With 2-Speed Heat Pump A97385
WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) THEMIDISTAT HEAT STAE 2 HEAT STAE 1 L STAE 1 24 VA HT DEIDIF 24 VA MM IDIF UTD SENS NNETIN / 1/ D FK4 IL 1 W1 Fig. 6 FK4 Fan oil With 1-Speed Air onditioner DH IDIFIE (24 VA) UTD SENS AI NDITINE EMVE J2 JUMPE F HEAT STAIN EMVE J1 JUMPE See notes 1, 2, 6, 13, and 15 A97387 THEMIDISTAT HEAT STAE 2 HEAT STAE 1 / L STAE 1 1/ L STAE 2 24 VA HT DEIDIF 24 VA MM IDIF UTD SENS NNETIN D FK4 IL W1 1 Fig. 7 FK4 Fan oil With 2-Speed Air onditioner IDIFIE (24 VA) UTD SENS See notes 1, 2, 6, 13, and 16 AI NDITINE EMVE J2 JUMPE F HEAT STAIN EMVE J1 JUMPE 1 2 A97388 THEMIDISTAT VS LIN HEAT STAE 3 / 1/ HEAT STAE 2 HEAT/L STAE 1 24 VA HT DEIDIF D FK4 IL W1 1 EMVE J2 JUMPE F HEAT STAIN EMVE J1 JUMPE THEMIDISTAT VS LIN HEAT/L STAE 1 HEAT STAE 3 HEAT/L STAE 2 24 VA HT DEIDIF / 1/ D FK4 IL 1 W1 DH J2 JUMPE 1 2 EMVE J1 24 VA MM 24 VA MM IDIF VS HEATIN UTD SENS NNETIN IDIFIE (24 VA) UTD SENS See notes 1, 2, 7, 14, and 15 IDIF VS HEATIN UTD SENS NNETIN IDIFIE (24 VA) UTD SENS See notes 1, 2, 4, 5, 14, and 16 Fig. 8 FK4 Fan oil With 1-Speed Heat Pump A97389 Fig. 9 FK4 Fan oil With 2-Speed Heat Pump A97390 11
WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) THEMIDISTAT / 1/ 1-STAE FUNAE AI NDITINE THEMIDISTAT L STAE 1 / 1/ 1-STAE FUNAE AI NDITINE 1 HEAT STAE 1 L STAE 1 24 VA HT W HEAT STAE 1 L STAE 2 24 VA HT W 2 24 VA MM IDIF UTD SENS NNETIN D IDIFIE (24 VA) UTD SENS See notes 13 and 15 Fig. 10 Single-Stage Furnace With 1-Speed Air onditioner A97391 IDIF UTD SENS NNETIN D IDIFIE (24 VA) UTD SENS See notes 13 and 16 Fig. 11 Single-Stage Furnace With 2-Speed Air onditioner A97392 THEMIDISTAT 1-STAE FUNAE THEMIDISTAT 1-STAE FUNAE VS LIN HEAT STAE 2 (FUNAE) HEAT/L STAE 1 (MPESS) / 1/ W VS LIN HEAT/L STAE 1 (MPESS L) HEAT STAE 3 (FUNAE) HEAT/L STAE 2 (MPESS HI) / 1/ W 1 2 24 VA HT 24 VA HT 24 VA MM 24 VA MM D D IDIF UTD SENS NNETIN IDIFIE (24 VA) UTD SENS See notes 3, 9, 14, 15, and 17 IDIF UTD SENS NNETIN IDIFIE (24 VA) UTD SENS See notes 3, 4, 5, 9, 14, 16, and 17 Fig. 12 Single-Stage Furnace With 1-Speed Heat Pump (Dual Fuel) A97393 12 Fig. 13 Single-Stage Furnace With 2-Speed Heat Pump (Dual Fuel) A97394
WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) THEMIDISTAT 2-STAE FUNAE AI NDITINE THEMIDISTAT 2-STAE FUNAE AI NDITINE HEAT STAE 2 / HEAT STAE 2 / 1/ L STAE 1 1/ 1 HEAT STAE 1 L STAE 1 HEAT STAE 1 L STAE 2 2 24 VA HT 24 VA HT 24 VA MM 24 VA MM D D IDIF UTD SENS NNETIN IDIFIE (24 VA) UTD SENS IDIF UTD SENS NNETIN IDIFIE (24 VA) UTD SENS See notes 6, 13, and 15 Fig. 14 Two-Stage Furnace With 1-Speed Air onditioner A97395 See notes 6, 13, and 16 Fig. 15 Two-Stage Furnace With 2-Speed Air onditioner A97396 THEMIDISTAT 2-STAE FUNAE THEMIDISTAT 2-STAE FUNAE VS LIN HEAT STAE 3 (FUNAE HI) HEAT STAE 2 (FUNAE L) HEAT/L STAE 1 (MPESS) / 1/ VS LIN / HEAT/L STAE 1 1/ (MPESS L) HEAT STAE 3 (FUNAE) HEAT/L STAE 2 (MPESS HI) 1 2 24 VA HT 24 VA HT 24 VA MM 24 VA MM D D IDIF UTD SENS NNETIN IDIFIE (24 VA) UTD SENS See notes 3, 7, 9, 10, 14, 15, and 17 IDIF UTD SENS NNETIN IDIFIE UTD SENS See notes 3, 4, 5, 8, 9, 10, 14, 16, and 17 Fig. 16 Two-Stage Furnace With 1-Speed Heat Pump (Dual Fuel) A97397 Fig. 17 Two-Stage Furnace With 2-Speed Heat Pump (Dual Fuel) A97398 13
VAIALE SPEED 80% NN-NDENSIN FUNAE AFS AD 1 THEMIDISTAT HEAT STAE 2 HEAT STAE 1 L STAE 1 / 1/ FUNAE AD AI NDITINE WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) VAIALE SPEED 80% NN-NDENSIN FUNAE AFS AD 1 THEMIDISTAT L STAE 1 HEAT STAE 2 HEAT STAE 1 L STAE 2 1/ / FUNAE AD AI NDITINE 1 2 24 VA HT 24 VA HT 24 VA M M 24 VA M M DEIDIF IDIF UTD SENS NNETINS D DE PL9-10 IDIFIE (24 VA) UTD SENS DEIDIF IDIF UTD SENS NNETINS D DE PL9-10 IDIFIE (24 VA) UTD SENS See notes 6, 10, 12, 13, and 15 See notes 6, 9, 10, 12, 13, and 16 A97434 Fig. 18 Variable-Speed Non-ondensing Furnace With 1-Speed Air onditioner A97435 Fig. 19 Variable-Speed Non-ondensing Furnace With 2-Speed Air onditioner VAIALE SPEED 80% NN-NDENSIN FUNAE AFS AD 1 THEMIDISTAT VS LIN HEAT STAE 3 HEAT STAE 2 HEAT/L STAE 1 / 1/ FUNAE AD VAIALE SPEED 80% NN-NDENSIN FUNAE AFS AD 1 THEMIDISTAT VS LIN HEAT/L STAE 1 HEAT STAE 3 HEAT/L STAE 2 / 1/ FUNAE AD 1 2 24 VA HT 24 VA HT 24 VA M M 24 VA M M DEIDIF IDIF UTD SENS NNETINS D DE PL9-10 IDIFIE (24 VA) UTD SENS DEIDIF IDIF UTD SENS NNETINS D DE PL9-10 IDIFIE (24 VA) UTD SENS See notes 3, 7, 9, 10, 12, 14, 15, and 17 See notes 3, 4, 5, 8, 9, 10, 12, 14, 16, and 17 A97436 A97437 Fig. 20 Variable-Speed Non-ondensing Furnace Fig. 21 Variable-Speed Non-ondensing Furnace With 1-Speed Heat Pump (Dual Fuel) With 2-Speed Heat Pump (Dual Fuel) 14
WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) THEMIDISTAT HEAT STAE 2 HEAT STAE 1 L STAE 1 24 VA HT / 1/ VAIALE-SPEED NDENSIN FUNAE AI NDITINE THEMIDISTAT HEAT STAE 2 L STAE 1 HEAT STAE 1 L STAE 2 24 VA HT / 1/ VAIALE-SPEED NDENSIN FUNAE AI NDITINE 1 2 DEIDIF 24 VA MM IDIF UTD SENS NNETIN A97418 Fig. 22 Variable-Speed ondensing Furnace With 1-Speed Air onditioner THEMIDISTAT VS LIN HEAT STAE 3 (FUNAE HI) HEAT STAE 2 (FUNAE L) HEAT/L STAE 1 (MPESS) 24 VA HT D / 1/ DH IDIFIE (24 VA) UTD SENS See notes 6, 10, 11, 13, and 15 VAIALE-SPEED NDENSIN FUNAE DEIDIF 24 VA MM IDIF UTD SENS NNETIN THEMIDISTAT VS LIN HEAT/L STAE 1 (MPESS L) HEAT STAE 3 (FUNAE) HEAT/L STAE 2 (MPESS HI) 24 VA HT D / 1/ DH IDIFIE (24 VA) UTD SENS See notes 6, 10, 11, 13, and 16 A97419 Fig. 23 Variable-Speed ondensing Furnace With 2-Speed Air onditioner VAIALE-SPEED NDENSIN FUNAE 1 2 DEIDIF 24 VA MM IDIF UTD SENS NNETIN D DH IDIFIE (24 VA) UTD SENS See notes 3, 7, 9, 10, 11, 14, 15, and 17 DEIDIF 24 VA MM IDIF UTD SENS NNETIN D DH IDIFIE (24 VA) UTD SENS See notes 3, 4, 5, 8, 9, 10, 11, 14, 16, and 17 A97420 Fig. 24 Variable-Speed ondensing Furnace With 1-Speed Heat Pump (Dual Fuel) 15 A97421 Fig. 25 Variable-Speed ondensing Furnace With 2-Speed Heat Pump (Dual Fuel)
WIIN DIAAMS FM "LD, KEN" AIE TSTATPH01- THEMIDISTAT (AIE WEATHEMAKE INFINIT SSTEM W/ 58MVP VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AIE IDIFIE, / UTD AI TEMP SENSS, IDEAL MFT/IDIT NTL W/ IDIF/DEIDIF FEATUES AND AUT TEMP NTLS, AND USE NTL INDEPENDENT FM ALL T HEAT/L/IF/DEIDIF) WIIN DIAAM NTES 1. efer to Fan oil Installation Instructions for features and additional wiring information 2. To activate dehumidify function on FK4, remove J1 jumper at fan coil control board. 3. Heat pump must have a high pressure switch for dual fuel applications. 4. efer to outdoor equipment Installation Instructions for proper setup. 5. Select the "zone" position on the 2-speed heat pump control board. 6. As an option / can be used to control second-stage heat. efer to indoor unit Installation Instructions for proper setup. 7. As an option, 1/ can be used to control third-stage heat. efer to indoor unit Installation Instructions for proper setup. 8. Furnace must control its own second-stage heat operation via furnace control algorithm. 9. utdoor air sensor must be attached in all dual fuel applications. 10. efer to indoor equipment Installation Instructions for proper setup. 11. To activate dehumidify feature on current style variable-speed furnaces (58MVP), a pilot duty 24-vac relay must be used. 12. To activate dehumidify feature on current style variable-speed 80% non-condensing furnace, disconnect green (DE) wire from on furnace control board and connect to dehumidify terminal on Thermidistat ontrol. 13. Dip switch No. 1 should be set in FF position for air conditioner installations. This is factory default. 14. Dip switch No. 1 should be set in N position for heat pump installations. 15. Dip switch No. 2 should be set in FF position for single-speed compressor operation. This is factory default. 16. Dip switch No. 2 should be set in N position for 2-speed compressor operation. 17. onfiguration ption No. 10 "Dual Fuel Selection" must be turned N in all dual fuel applications. IDIF/DEIDIF UTPUT N INDIATS Within humidity select screen (selected by Humidity button and indicated by "hu" or "dhu" on clock display), triangle under humidity setpoint will be on while humidify output is on. Triangle under dehumidify setpoint will be on while dehumidify output is active (turned off, because this output is reverse logic). AUT HANEVE When auto changeover mode is selected, a change from heat to cool (or vice versa) will not occur until an opposite mode demand has existed for 20 minutes. If setpoint is changed, 20-minute requirement is deleted. EMEEN HEAT MDE When Thermidistat ontrol is configured as a heat pump and emergency heat is selected, all signals are locked out, and W becomes energized upon a call for heat. PWE N HEK When A power is first applied, all segments of display are turned on for a few seconds. Following this, temperature display indicates model/configuration via following 2-digit code: A 1-speed air conditioner, HP 1-speed heat pump, A2 2- speed air conditioner, H2 2-speed heat pump, HS 1-speed heat pump with 3-stage auxiliary heat, F dual fuel, d2 dual fuel with 2-speed. E DES -- If Thermidistat ontrol cannot properly read room temperature, display will indicate -- and all outputs (except fan if on) will turn off. E1, E2 There is no E1 or E2 error message. E3 If Thermidistat ontrol cannot properly read outdoor temperature, and it is needed for proper operation, display will indicate E3. E4 If Thermidistat ontrol s internal memory fails, E4 will be displayed. eplace Thermidistat ontrol. E5 If Thermidistat ontrol cannot properly read humidity, E5 will be displayed. eplace Thermidistat ontrol. E6 If defrost cycle continues for longer than 15 minutes. E6 will be displayed. heck heat pump wiring or for failed heat pump defrost control. SMAT EVE With Smart ecovery selected, transition out of setback begins a fixed time period before selected recovery time and gradually adjusts room temperature so desired temperature will be achieved at selected recovery time. The fixed time period is 1.5 hr. It operates in both heating and cooling. Thermidistat ontrol Troubleshooting SMPTM WHAT T HEK pen Thermidistat ontrol. heck for 24vac between and at screw terminals on mounting base. eassemble, No display making sure pins on board engage sockets in mounting base. If display does not appear, replace the Thermidistat ontrol. "--" in place of room temperature Thermidistat ontrol cannot properly read room temperature. eplace Thermidistat ontrol. "E3" or "--" in place of outdoor temperature Thermidistat ontrol cannot properly read outdoor temperature. heck outdoor sensor and its wiring. "E4" or "E5" Internal failure. eplace Thermidistat ontrol. "E6" System is stuck in defrost. heck wiring and heat pump defrost control board. "lean Filter" icon displayed Filter timer has expired. lean or replace filter, then press VAATIN and HLD/END buttons together to reset. ooling or heating will not come on See Installer Setup to force heating/cooling. heck for 24vac at equipment terminals. If not present, check wiring. Humidify or dehumidify will not come on See Installer Setup to force or DE. heck for 24vac at equipment terminals. If not present, check wiring. opyright 1997 AIE orp. 7310 W. Morris St. Indianapolis, IN 46231 tstat13si Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. ook 1 4 P 101 atalog No. 92-33TS-TA51 Printed in U.S.A. Form TSTAT-13SI Pg 16 7-97 eplaces: New Tab misc. misc.
8. Appendix A - Wiring Diagrams User Interface Variable-Speed Furnace/ Fan oil ommunicating A or HP* A reen - Data A ellow - Data A reen ellow A White - M White D ed - 24VA D ed D ptional emote oom Sensor Humidifier onnection AD onnections M 24V AT AT Sensor (ptional) *NTE: Some outdoor units do not require the and D connections. See outdoor unit Installation Instructions. *NTE: For SPP products, AD connection between Indoor and utdoor control boards are pre-wired at the factory. *NTE: For new SPP installations in which the AT Sensor is required, please refer to the SPP Installation Instructions. Universal Four-Wire onnection A13124 71 WIIN DIAAMS FM "NEW" INFINIT TUH NTL WITH WIFI INTENET AESS (SSTXIT01-A) IDEALL, WULD LIKE T SETUP F AIE "IDEAL MFT & IDIT NTL" T NTL AUTMATIALL IND TEMPEATUE SINLE ZNE WITH AIE 58MVP WEATHEMAKE INFINIT VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AND AIE IDIFIE. ADDITINAL NTLS INLUDE IDIF/DEIDIF EVEN IN ASENE F ALL T HEAT L, AND USE NTL NTL WITH AUTMATI (ALL T HEAT/L) AND MANUAL (NTINUUS ) SETTINS, AND MMUNIATIN WITH UTD AI TEMPEATUE SETTINS T HELP NTL/PEVENT ALL T L WHEN UTSIDE TEMP IS T LW AND AILIT T ATIVATE/DEATIVATE PTINAL SETTIN T ESTIT IDIFIATIN WHEN UTSIDE TEMP IS DANEUSL LW T HELP PEVENT ( NT) IND NDENSATIN.
User Interface Variable-Speed Furnace/Fan oil A reen - Data A A ellow - Data White - M AD onnection D ed - 24VA D ptional emote oom Sensor Humidifier onnection 1-Spd. Non-ommunicating A M 24V AT AT Sensor onnection Diagram for Furnace or FE Fan oil with 1 -Stage Air onditioning A12354 72 WIIN DIAAMS FM "NEW" INFINIT TUH NTL WITH WIFI INTENET AESS (SSTXIT01-A) IDEALL, WULD LIKE T SETUP F AIE "IDEAL MFT & IDIT NTL" T NTL AUTMATIALL IND TEMPEATUE SINLE ZNE WITH AIE 58MVP WEATHEMAKE INFINIT VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AND AIE IDIFIE. ADDITINAL NTLS INLUDE IDIF/DEIDIF EVEN IN ASENE F ALL T HEAT L, AND USE NTL NTL WITH AUTMATI (ALL T HEAT/L) AND MANUAL (NTINUUS ) SETTINS, AND MMUNIATIN WITH UTD AI TEMPEATUE SETTINS T HELP NTL/PEVENT ALL T L WHEN UTSIDE TEMP IS T LW AND AILIT T ATIVATE/DEATIVATE PTINAL SETTIN T ESTIT IDIFIATIN WHEN UTSIDE TEMP IS DANEUSL LW T HELP PEVENT ( NT) IND NDENSATIN.
FE Fan oil or Variable Speed Furnace Input Wiring for lower peration A07114 77 WIIN WIIN DIAAMS DIAAMS FM FM "NEW" INFINIT TUH NTL WITH WITH WIFI WIFI INTENET AESS INTENET AESS (SSTXIT01-A) (SSTXIT01-A) IDEALL, IDEALL, WULD SETUP LIKE F T AIE SETUP "IDEAL F MFT AIE &"IDEAL IDIT MFT NTL" & T IDIT NTL NTL" T NTL AUTMATIALL IND TEMPEATUE AUTMATIALL SINLE IND ZNE TEMPEATUE WITH AIE SINLE 58MVP ZNE WEATHEMAKE WITH AIE 58MVP INFINIT WEATHEMAKE VAIALE SPEED INFINIT AS VAIALE FUNAE, SPEED SINLE AS FUNAE, STAE SINLE AIE STAE AI NDITINE, AIE AI AND NDITINE, AIE AND IDIFIE. AIE IDIFIE. ADDITINAL ADDITINAL NTLS NTLS INLUDE INLUDE IDIF/DEIDIF EVEN IN ASENE F ALL T HEAT IDIF/DEIDIF EVEN IN ASENE F ALL T HEAT L, AND L, AND USE NTL NTL WITH AUTMATI (ALL USE NTL NTL WITH AUTMATI (ALL T HEAT/L) AND T HEAT/L) MANUAL (NTINUUS AND MANUAL ) (NTINUUS SETTINS, AND MMUNIATIN ) SETTINS, WITH AND UTD MMUNIATIN AI TEMPEATUE WITH SETTINS UTD T AI TEMPEATUE SETTINS T HELP HELP NTL/PEVENT ALL T L WHEN UTSIDE TEMP TEMP IS T IS LW T AND LW AILIT AND AILIT T T ATIVATE/DEATIVATE PTINAL SETTIN T ESTIT ATIVATE/DEATIVATE IDIFIATIN PTINAL WHEN UTSIDE SETTIN T TEMP ESTIT IS DANEUSL IDIFIATIN LW WHEN T HELP UTSIDE PEVENT TEMP IS ( DANEUSL NT) IND LW NDENSATIN. T HELP PEVENT ( NT) IND NDENSATIN.
FE Fan oil or Variable Speed Furnace Input Wiring for System Shutdown A07115 78 WIIN DIAAMS FM "NEW" INFINIT TUH NTL WITH WIFI INTENET AESS (SSTXIT01-A) IDEALL, WULD LIKE T SETUP F AIE "IDEAL MFT & IDIT NTL" T NTL AUTMATIALL IND TEMPEATUE SINLE ZNE WITH AIE 58MVP WEATHEMAKE INFINIT VAIALE SPEED AS FUNAE, SINLE STAE AIE AI NDITINE, AND AIE IDIFIE. ADDITINAL NTLS INLUDE IDIF/DEIDIF EVEN IN ASENE F ALL T HEAT L, AND USE NTL NTL WITH AUTMATI (ALL T HEAT/L) AND MANUAL (NTINUUS ) SETTINS, AND MMUNIATIN WITH UTD AI TEMPEATUE SETTINS T HELP NTL/PEVENT ALL T L WHEN UTSIDE TEMP IS T LW AND AILIT T ATIVATE/DEATIVATE PTINAL SETTIN T ESTIT IDIFIATIN WHEN UTSIDE TEMP IS DANEUSL LW T HELP PEVENT ( NT) IND NDENSATIN.