Water Separator Series The series water separator is installed on the air pressure line to remove water drops in the compressed air. It is suitable for use in cases where "water must be removed, but the air does not have to be as dry as when an air dryer is used" or "an air dryer cannot be used because an electric power supply is not available". Through the adoption of an element that is used exclusively for removing water drops and the provision of ample housing interior space, a % water removal rate has been achieved. Water separator can remove water droplets, but it cannot remove moisture. Condition of inlet air Pressure: 0.7MPa Temperature: 2 C Relative humidity: 0% Liquid water content (Water droplet content): 1.g/m 3 (ANR) Compressed air flow: Rated flow of each model Removed rate of water % = Removed water (Water droplet) g x 0 Inflowed water (Water droplet) g Various equipment for drain discharge (1) Flow rate (l /min (ANR)) Port size (Nominal size ) Weight (kg) Specifications 10 300 Fluid Max. operating pressure Min. operating pressure Proof pressure Ambient/Fluid temperature Removal rate of water Element life With N.O. auto drain: 0.1MPa Accessories (Options) Applicable model racket assembly With cap bolt With spring washer 20 70 30 20 300 6000 0.3 0. 0. 1.4 2.1 4.2. Note 1) Max. flow is at 0.7MPa. Max. flow depends on operating pressure. Please refer to p.4.3-2 for flow rate and to p.4.3-3 for graph of max. flow. How to Order E Compressed air 1.0MP 0.0MPa 1.MPa to 60 C % 2 years or when pressure drop reaches 0.1MPa 10 20 30 M1 M2 M3 M4 M M6 M7 20 F 03 J ody size 10 1 / 20 1 /4 30 3 / 40 1 /2 0 3 /4 60 1 0 1 1 /2 Ordering source area code Japan, Asia - Australia E Europe N North America 1 /, 1 /4, 3 / 1 /4, 3 /, 1 /2 3 /, 1 /2, 3 /4 Thread Rc (PT) F G(PF) N NPT 01 1 / 02 1 /4 03 3 / 04 1 /2 Port size 3 /4 1 06 1 1 /2 2 1 /2, 3 /4, 1 3 /4, 1 1, 1 1 /2 1 1 /2, 2 Options J Drain guide 1 /4 female thread R IN-OUT reverse direction Accessories (Options) Symbol Description No accessories racket C N.C. auto drain D N.O. auto drain Please refer to the following table for combinations of accessories and options. Note) Please refer to p.4.7-6 about "How to Order" case assembly. HA IDG AFF AM FQ1 Related products Symbol Option combinations Available Not available Accessories Options Applicable model Accessories/Optional specification C D J R 10 20 30 N.C. auto drain C Accessories N.O. auto drain D Drain guide 1 /4 J Options IN-OUT reverse direction R 4.3-1
Series Flow Rate 10 Initial condition of element Note) If compressed air is above max. flow, water separator cannot operate well. 1 / 3 /4 Precautions e sure to read before handling. Refer to p.0-26 and 0-27 for Safety Instructions and common precautions on the products mentioned in this catalogue, and refer to p.4.0- to 4.0-7 for more detailed precautions of every series. Design 20 1 /4 1 qplace this product in a location that is not likely to create pulsations. If the internal/external pressure difference exceeds 0.1 MPa, the element could break. wwhen using an auto drain, drain pipes must be connected within the following range: Normally closed (N.C.) Normally open (N.O.) Tube fittings are provided. Therefore, use a mm external tube, and keep the pipe length within m. type (N.O.) Use a tube with a minimum bore of mm, and keep its length within 2.m. When using a normally open (N.O.) auto drain, because the valve does not close until the air pressure becomes higher than 0.1MPa, the air could keep discharging from the drain discharge section of an air compressor with a small air discharge volume. Therefore, make sure to use a normally closed (N.C.) auto drain with a compressor under 3.7kW. ethe bracket that is provided with the product is for supporting the product itself. Separate supports must be provided for piping and other connection devices. 30 3 / 1 1 /2 Installation qverify the direction of the compressed air flow and the " " mark that indicates the inlet side of the product before connecting. It cannot be used with its direction reversed. 1 /2 wmake sure to install this product horizontally. If it is installed diagonally, sideways, or upside down, the drainage that was separated by the element will splash to the secondary side. Maintenance qthe element replacement period is when the pressure drop has reached 0.1MPa or 2 years have elapsed after it has been put into use, whichever comes first. wwhen it is time to replace the element, immediately replace it with a new element. Also replace the O ring and the gasket. ewhen using a product equipped with a drain valve, drain guide, or a ball valve, discharge the drainage before the drain fluid surface reaches the center of the sight glass. If it is not discharged properly, the drainage will flow out to the secondary side. 4.3-2
Water Separator Series Construction 10 to Component Parts No. q w e Description ody Housing Sight glass Replacement Parts No. Description Material Element Resin r assembly NR With gasket, With O ring Material Aluminum die cast Aluminum die cast Tempered glass 10 -EL10 Remark Chromate treatment, Epoxy coating on inner surface : Aluminum casting 20 -EL20 30 -EL30 Part No. -EL40 Note: Constructions show sight glass, but mounting position is different from actual position. Please refer to p.4.3-4 and 4.3- about drawings for more detailed. -EL0 -EL60 -EL0 Max. Air Flow How to Select Follow the procedure given below to select the model in accordance with the inlet pressure and maximum air flow rate requirements. (Example) Inlet pressure : 0.6 MPa Maximum air flow rate: m 3 /min (ANR) qusing the "Max. air flow", find point A, at which the input pressure and the maximum air flow rate intersect. wto select one with the maximum air flow rate line that is located above the obtained intersecting point A, the model will be. Note) Make sure to select a model with the maximum air flow rate line that is located above the obtained intersection point. A model with the maximum air flow rate line that is located below the obtained intersection point will have an excess flow rate, and will not satisfy the specifications. HA IDG AFF AM FQ1 Related products 4.3-3
Series 10 to Dimensions Accessories D: With auto drain (N.O. Type) C: With auto drain (N.C. Type) N.C. type of is not available. Options J: With drain guide 10 20 30 Port Size (Nominal size ) 1 /, 1 /4, 3 / 1 /4, 3 / 1 /2 3 /, 1 /2 3 /4 1 /2, 3 /4 1 3 /4, 1 1, 1 1 /2 A 1 172 17 4 2 22 232 2 311 13 13 16 16 1 1 22 22 32 C 0 113 11 11 1 173 0 23 D 63 0 0 6 6 122 160 E F 63 0 0 6 6 122 160 G H 1 17 17 21 21 241 241 277 334 I 6 0 0 0 0 0 10 J 1 17 22 1 2 21 30 40 K 1 Mounting Dimensions L 12 12 16 M. 6 6 7 7 11 N 3 40 40 0 0 6 O 4 0 0 2 136 P 70 4 4 0 0 1 1 130 10 Q 26 2 2 34 34 0 0 60 R 4. 12 S 1.6 2.0 2.0 2.3 2.3 3.2 3.2 4. 4. 4.3-4
Water Separator Series Dimensions Accessory D: With auto drain (N.O. type) for HA IDG AFF AM FQ1 Related products Port size (Nominal size ) 1 1 / 2, 2 A 460. 42 C 34 D 2 E 7. F 2 G H 463. I 10 J 30 K 1 Mounting Dimensions L 24 M 13 N 1 O 14 P 2 Q 1 R 1 S 6.0 4.3-
Series Made to Order Specifications Consult SMC for detailed specifications, size and delivery. Order Made qwith IN-OUT flange Available for flange piping easily. Specifications Applicable to How to Order : Refer to p.4.3-1 for "How to Order" standard specifications. X1 ody size Optional specifications Thread Accessories Port size Dimensions Connection 3/4, FF, K 1, FF, K 1 1/2, FF, K 2, FF, K A 240 260 300 30 26 300 34 46. 4.3-6