//7 9-- INSTALLATI INSTRUCTIS WIRELESS OUTDOOR DETECTOR FTN-RRHW/FTN-RRIX FTN-RRG/FTN-RRDS FTN-RRHW Honeywell 8 Series Compatible FTN-RRIX Interlogix 9.MHz Compatible FTN-RRG GIG Compatible FTN-RRDS DSC MHz Compatible Product is not produced by, endorsed by, nor is officially associated with Honeywell, Interlogix, GIG, QOLSYS or DSC. FEATURES CTENTS Narrow Angle Detection Detection Range Adjustability (m / m) Intelligent AND logic Horizontal Adjustability Tamper Output Install in accordance with the Standard for Installation and Classification of Burglar and Holdup Alarm Systems, UL 8. FCC NOTICE This device complies with Part of the FCC rules. Operation is subject to the following two conditions: () This device may not cause harmful interference. () This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the Resolution Products, Inc. could void the user s authority to operate this equipment. IC NOTICE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: () This device may not cause interference, and () This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux cnr d Industrie Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: () L appareil ne doit pas produire de brouillage, et () L utilisateur de l appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. Honeywell, GIG, Interlogix, DSC are trademarks owned by Honeywell International, Inc, rtek Security & Control LLC, United Technologies Corporation, and Tyco Safety Products Canada LTD, respectively. OPTEX Inc. products will function with one of either Honeywell, GIG, Interlogix, or DSC systems. However, no OPTEX Inc. product is produced by, endorsed by, nor is officially associated with Honeywell, GIG, Interlogix, DSC. OPTEX Inc. recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. -- INTRODUCTI - BEFORE INSTALLATI... - ZE CFIGURATI... - PARTS IDENTIFICATI... - DETECTI AREA... INSTALLATI - WIRING DIAGRAM... - ENROLLING TO PANEL... - MOUNTING... 9 WALK TEST - WALK TEST... DIP SWITCH SETTING - WALK TEST MODE... - BATTERY SAVING TIMER... - ALARM & TROUBLE OUTPUT... - LED... - PIR SENSITIVITY... OTHERS - LED LIGHT PATTERN... BATTERY - HOW TO REPLACE BATTERY... - BATTERY LIFE... 7 SPECIFICATIS 7- SPECIFICATIS... 7- DIMENSIS...
INTRODUCTI - BEFORE INSTALLATI Warning Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury. Caution Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage. Avertissement Le non respect des instructions données avec ce signe et une mauvaise manipulation peuvent causer la mort ou des blessures graves. Attention Le non respect des instructions données avec ce signe et une mauvaise manipulation peuvent causer des blessures et/ou des dommages aux biens. The check mark indicates recommendation. The nix Le signe de coche sign indicates prohibition. indique une recommandation. Le signe de négation Warning/Avertissement indique une interdiction. Caution/Attention Do not remove the PCB. Ne pas enlever le PCB. Do not touch the PCB except for the DIP switch. Ne pas toucher le PCB sauf les interrupteurs DIP. Mounting height. Hauteur de montage. Keep the detector parallel to the ground. Consider the direction a person is approaching from, as well as the Maintenir le détecteur parallèle au sol. detection area. Tenir compte de la direction d approche d une personne de même que de la zone de détection..8. m ('7" '") Tilt Ne pas incliner Parallel Parallèle Install the detector in a place where it is free from false alarm factors. For example: Installer le détecteur dans un emplacement ne présentant pas de cause de fausses alarmes. Par exemple : Direct Sunlight and reflection Lumière solaire et réflexion Heat source Source de chaleur -- Objects moving in the wind Objets bougeant au vent
- ZE CFIGURATI SUGGESTIS Set up FITLINK according to location as desired. Below are zone configurations for typical location types. Alarm Output Location Disarm Away Stay Front Porch; Backyard Carport; Gate Entrance; Deck Crawl Space; Basement; Storage Shed; Instant Alarm Instant Alarm Garage or Sliding Glass Door; Screened in Porch; Sunroom Entry delay Driveway; Sidewalk; Public Areas - Panel Event Chime Report to CMS Alarm Trouble Toggle On or Off On during disarm Entry delay On during disarm Toggle On or Off PARTS IDENTIFICATI Mounting base Accessories>> Screw kit Screw cap Bracket For wall mounting Screw ( mm) Main unit cover Main unit Transmitter compartment Lens Screw IC ID FTN-RRHW: 8A-RE FTN-RRG: 8A-RE FTN-RRIX: 8A-RE FTN-RRDS: 8A-RE Fixture Screw -- te>> FCC ID FTN-RRHW: UX-REX FTN-RRG: UX-REX FTN-RRIX: UX-REX FTN-RRDS: UX-RE
- DETECTI AREA Top view Side view m detection length Adjustable range: 9 (by pitch).8.. m detection length Adjustable range: 9 (by pitch).8.. INSTALLATI - WIRING DIAGRAM - Overall wiring diagram Transmitter Bracket Red Black White Yellow Red: Power input (+) Black: Power input (-) White: Alarm Yellow: Alarm Green Blue Green: Tamper Blue: Tamper Main unit A GND B te>> The battery in the transmitter is shared with the detector. Connection for TROUBLE is used when monitoring for Tamper. --
- ENROLLING TO CTROL PANEL Enrolling to Honeywell LYNX Touch L/L7 Series. Place the panel into wireless enrollment mode and then trip the tamper three times.. Set Loop Number to.. Set Device type to Other.. Set Response Type and Alarm Report according to following table.. Set Chime to your preferred type.. Set Supervision to Supervised. Response Type Alarm Report Silent Burglary Crawl Space; Basement; Storage Shed Perimeter Garage or Sliding Glass Door; Screened in Porch; Sunroom Entry Exit Silent Burglary Location Front Porch; Backyard Carport; Gate Entrance; Deck Driveway; Sidewalk; Public Areas Enrolling to Honeywell Residential Vista Panels. While in program mode, press * to enter Zone Programming Menu Mode.. Select or to determine if you will confirm the sensor after learning it.. Enter the zone number that you wish to program (or to exit zone programming). Press [*] to continue.. A summary display appears, press [*] to continue.. Enter Zone Type according to table.. Enter Partition. 7. Enter Report codes according to table. 8. Enter Input Type to = RF (supervised RF transmitter). 9. Learn or input transmitters serial number. (To learn FITLINK, trip the tamper three times.). Change Loop Number to. Location Front Porch; Backyard Carport; Gate Entrance; Deck Crawl Space; Basement; Storage Shed Garage or Sliding Glass Door; Screened in Porch; Sunroom Driveway; Sidewalk; Public Areas Zone Type Type Silent Burglary Report Codes Type Other than Perimeter Burglary Type Entry Exit Other than Type Silent Burglary --
- ENROLLING TO CTROL PANEL Enrolling to GIG GC/GC. Select RF Sensor # ( to 8).. Select Sensor Type according the following table.. Select Sensor Equipment Code as [] Other or [9] Existing Motion Detector.. Select Sensor Other Equip code as [] (this menu only appears if [] Other was selected in the previous menu.. At the Sensor Serial Number menu, press shift, then press Learn, and then trip detector tamper switch.. Select Equipment Age as New. 7. Select Loop Number as Loop. 8. Select Dialer Delay as Enabled. 9. Edit Voice Descriptor according to location.. Select Sensor Reports according to following table.. Select Sensor Supervised to Enabled.. Select the desired chime. Location Sensor Type Sensor Reports Front Porch; Backyard Carport; () Response Type Gate Entrance; Deck Crawl Space; Basement; Storage Shed () Perimeter () Exit/Entry () Response Type Garage or Sliding Glass Door; Screened in Porch; Sunroom Driveway; Sidewalk; Public Areas --
- ENROLLING TO CTROL PANEL Enrolling to DSC PowerSeries. Put control panel into learn sensor mode.. Push tamper switch to enroll FITLINK.. Press [*] key to confirm ID.. Enter [zone #].. Enter [zone type] according to the following table.. Press the tamper again to Activate the Device for Test. 7. Set Zone Attributes according to following table. Location Front Porch; Backyard Carport; Gate Entrance; Deck Zone Types -hour n-alarm Zone Attributes Set Chime or OFF Crawl Space; Basement; Storage Shed Instant Keep as defaults Garage or Sliding Glass Door; Screened in Porch; Sunroom Delay Keep as defaults Driveway; Sidewalk; Public Areas -Hour n-alarm Enrolling to Qolsys IQ PANEL Set Chime or OFF. Enter Settings Menu and select "Installation".. Select "Security Sensors" and then select "Auto Learn Sensor".. Trip the tamper to enroll within min.. Panel will chime and display the sensor's code. Select OK to confirm.. Set "Sensor Type" to "Motion".. Set "Sensor Name" to the correct name from the list. 7. Set "Chime Type" to your preferred type. 8. Set Sensor Group according to following table. 9. Select "Add New" to complete. Location Front Porch; Backyard Carport; Deck; Gate Entrance Sensor Group : Safty Motion Crawl Space; Basement; Storage Shed 7: Away - Instant Motion Garage or Sliding Glass Door; Screened in Porch; Sunroom : Away - Delay Motion Driveway; Sidewalk; Public Areas : Safety Motion -7-
- ENROLLING TO CTROL PANEL Enrolling to Interlogix Simon XTi. Put control panel in learn sensor mode.. Push tamper switch to enroll FITLINK.. Enter Sensor Number. Select Sensor group according to following table.. Change Sensor Name of Item to the correct name from the list.. Press save to save the changes. Location Sensor Type Front Porch; Backyard Carport; : Local special chime Gate Entrance; Deck Crawl Space; Basement; Storage Shed : Instant perimeter Garage or Sliding Glass Door; Screened in Porch; Sunroom : Entry/exit delay Driveway; Sidewalk; Public Areas : Local special chime Enrolling to Interlogix Concord /Concord Express. Put control panel in learn sensor mode.. Select partition.. Enter the sensor group according to following table.. Push tamper switch to enroll FITLINK.. Exit learn sensor mode Enrolling to Interlogix AdvisorOne. From the Sensors screen, press LEARN RF.. Select the sensor group according to following table.. Push tamper switch to enroll FITLINK.. Press CLOSE.. Press EDIT to edit the options.. Select Chime Mode as desired. 7. Press SAVE and CLOSE. Location Sensor Type Front Porch; Backyard Carport; : Local special chime Gate Entrance; Deck Crawl Space; Basement; Storage Shed : Instant perimeter Garage or Sliding Glass Door; Screened in Porch; Sunroom : Supplementary Extended Delay Driveway; Sidewalk; Public Areas : Local special chime -8-
- MOUNTING Remove the mounting base. Open the knockout. Mounting base Joint screw knockout Joint screw knockout Mount the mounting base on the wall. Screw ( mm) mm Use this knockout screw hole to mount the base, when making the wall tamper switch effective. If the main unit is peeled off from a wall, this plastic part will be cracked and remain on a wall, activating the tamper switch. Mounting height:.8. m Screw ( mm) te>> Transmitter needs to be enrolled to reciever before installing the detector. Attach the bracket and main section. Open the main unit cover te>> Be sure to set the screw cap after installing the mounting base. -9-
Determine the horizontal detection angle and attach the fixture. tes>> te>> To make adjustments, remove the fixture. Align the detection area parallel to the wall to reduce interference with the wall. te>> Check that the fixture and bracket engage correctly. When the unit is mounted on the corner to look ahead along the wall, choose the guide-mark located on the opposite side of the wall. When the unit is mounted on the wall and the detection pattern is at 9 degrees, choose the corresponding engraved guide mark. - -
8 Determine the detection length. ( m or m) If m is required, rotate the lower lens 8 degrees. te>> Do not remove the upper lens. m detection length (Factory default) m detection length Side view Side view.8.. 9 Attach the fixture..8.. Attach the main unit cover. te>> To prepare for walk test, check that DIPswitch (WALKTEST MODE) is set to (TEST) before attaching main unit cover. Fixture walk test. Perform For details, refer to -. walk test is complete, set DIP After switch (WALK TEST MODE) from to OFF. te>> The battery life will be shortened unless the DIP switch is set to OFF. - -
WALK TEST - WALK TEST Set the DIP switch (WALK TEST MODE) to (TEST). Check that LED lights for seconds when the intended object is detected. DIP switch Detected t detected te>> The switch is set to (TEST) by factory default. Set the DIP switch (WALK TEST MODE) to OFF (NORM). tes>> DIP switch The battery life will be shortened unless the DIP switch is set to OFF. To use the LED in normal operating condition, set the DIP switch to. DIP SWITCH SETTING Do not touch the PCB except for the DIP switch. DIP switch : Factorydefault - WALK TEST MODE TEST WALK TEST MODE BATTERY SAVING TIMER ALARM & TROUBLE OUTPUT LED PIR SENSITIVITY N/A NORM DIP switch Position Function TEST (Factory default) The LED lights irrespective of the DIP switch (LED) setting. The DIP switch (BATTERY SAVING TIMER) setting is inactive. NORM The LED lights depending on the DIP switch (LED) setting. The DIP switch (BATTERY SAVING TIMER) setting is active. - -
- BATTERY SAVING TIMER S S te>> The detector will not generate alarms at intervals shorter than the specified time. - Position S S (Factory default) N.O. - sec. N.C. N.O. output N.C. (Factory default) N.C. output Position OFF PIR SENSITIVITY Function LED LED OFF OFF (Factory default) - Function DIP switch DIP switch N.O. sec. Position LED Function ALARM & TROUBLE OUTPUT DIP switch te>> If the LED lights, check the DIP switch (WALKTEST MODE) setting. DIP switch STD Position LOW STD (Factory default) LOW - - Function rmal sensitivity Low sensitivity
OTHERS - LED LIGHT PATTERN The following explains the LED light pattern. LED Blink Detector condition Light LED indicator Warm-up te>> The LED blinks even if the DIP switch (LED) is set to OFF. Blinks for approx. seconds. Alarm Lights for seconds. - - OFF
BATTERY The detector shares the battery with the transmitter. - HOW TO REPLACE BATTERY Remove the bracket and main section. Replace the battery. Install a new battery. Attach the bracket and main section. - BATTERY LIFE The values indicated are only for reference on each condition. The sensor will send low battery transmissions to the control panel. CRA ( V, mah) Alarm trigger per day Battery Life Approx. years Approx. years - -
7 SPECIFICATIS 7- SPECIFICATIS Model FTN-RRHW Detection method PIR coverage Detection length limit Detection width Detectable speed Sensitivity Power source Current draw Alarm period Warm-up period Alarm output Trouble output Passive infrared '" '" ( m) '7", '" ( m, m) '" wide at '" / " wide at '7" ' '"/s (.. m/s). F (at '/s) (. C (at. m/s)) CRA Lithium battery.μa standby / ma max. at V DC. ±. sec. Approx. sec. (LED blinks) N.C./N.O. Selectable-Solid State Switch V DC. A (max.) N.C./N.O. Selectable-Solid State Switch V DC. A (max.) Enable: During DIP switch (WALK TEST MODE) or DIP switch (LED) Disable: During normal operation Light/Blink: Warm-up, alarm alarm V/m - to + F (- to + C) 9% max. IP Wall (Outdoor, Indoor) '7" to '" (.8 to. m). oz. (8g) without wireless transmitter and battery screw ( mm) LED indicator RF Interference Operation temperature Environment humidity Weatherproof Mounting Mounting height Weight Accessories FTN-RRIX FTN-RRG FTN-RRDS *Specifications and design are subject to change without prior notice. 7- DIMENSIS NOTE These units are designed to detect an intruder and activate an alarm control panel. Being only a part of a complete system, we cannot accept responsibility for any damages or other consequences resulting from an intrusion..9 (7.) Unit: in (mm).7 (.) For programming technical support: 877--78 For OPTEX support: 8-9-789 support@optexamerica.com www.optexamerica.com. (7.) OPTEX INC. (U.S.) URL: http://www.optexamerica.com OPTEX SECURITY SAS (France) URL: http://www.optex-security.com OPTEX KOREA CO.,LTD. (Korea) URL: http://www.optexkorea.com OPTEX DO BRASIL LTDA. (Brazil) URL: http://www.optex.net/br/es/sec OPTEX SECURITY Sp.z o.o. (Poland) URL: http://www.optex.com.pl OPTEX (EUROPE) LTD. / EMEA HQ (U.K.) URL: http://www.optex-europe.com OPTEX PINNACLE INDIA, PVT., LTD. (India) URL: http://www.optex.net/in/en/sec OPTEX (DGGUAN) CO.,LTD. SHANGHAI OFFICE (China) URL: http://www.optexchina.com OPTEX TECHNOLOGIES B.V. (The Netherlands) URL: http://www.optex.eu OPTEX (Thailand) CO., LTD. (Thailand) URL: http://www.optex.net/th/th Copyright (C) 7 OPTEX CO.,LTD. - -