Power Distribution Unit for IP-NINJAR PDU-1209 User s Guide Ver. 1.0.0 Thank you for choosing this IDK product. To ensure the best performance of this product, please read this User s Guide fully and carefully before using it and keep this manual beside this product. IDK Corporation
Trademarks Blu-ray Disc and Blu-ray are trademarks of Blu-ray Disc Association. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries. All other company and product names mentioned in this manual are either registered trademarks or trademarks of their respective owners. In this manual, the or marks may not be specified. 2
Before reading this manual All rights reserved. Some of the contents in this User s Guide such as product appearance in diagrams, menu operations, communication commands, and so on may differ depending on the version of the product. This User s Guide is subject to change without notice. You can download the latest version from IDK s website at: http://www.idkav.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. Note: This equipment was tested with shielded cables on the peripheral devices. Shielded cables must be used with the equipment to ensure compliance with FCC emissions limits. CE MARKING This equipment complies with the essential requirements of the relevant European health, safety and environmental protection legislation. WEEE MARKING Waste Electrical and Electronic Equipment (WEEE), Directive 2002/96/EC (This directive is only valid in the EU.) This equipment complies with the WEEE Directive (2002/96/EC) marking requirement. The left marking indicates that you must not discard this electrical/electronic equipment in domestic household waste. 3
Safety Instructions Read and understand all safety and operating instructions before using this product. Follow all instructions and cautions as detailed in this document. Enforcement Symbol Warning Caution Description Indicates the presence of a hazard that may result in death or serious personal injury if the warning is ignored or the equipment is handled incorrectly. Indicates the presence of a hazard that may cause minor personal injury or property damage if the caution is ignored or the equipment is handled incorrectly. Symbol Description Example Caution This symbol is indicated to alert the user. (Warning and caution) Electrical Hazard Prohibition This symbol is intended to prohibit the user from actions. Do not disassemble Instruction This symbol is intended to instruct the user. Unplug 4
Prohibition Do not disassemble Do not touch Instruction Unplug Do not place the product in any unstable place. Install the product to a horizontal and stable place. Otherwise, it may fall/turn over and lead to injury. Do not place the product in any environment with vibration. Otherwise, it may move/fall and lead to injury. Keep out any foreign objects. In order to avoid fire or electric shock, do not allow foreign objects, such as metal and paper, to enter the product from the vent holes. For power cable/ plug: Do not scratch, heat, or modify, including extending them. Do not pull, put heavy stuff on them, or pinch them. Do not bend, twist, or tie them together forcefully. If they are used in those states continuously, it may cause fire or electric shock. If power cables/plugs become damaged, contact IDK. Do not repair, modify or disassemble. Since the product includes high-voltage part, those actions may cause fire or electric shock. For internal inspections or repairs, contact IDK. In the event of lighting or thunder, do not touch the main unit and cables such as power cable and LAN cable. Contact may cause electric shock For installation: The product is intended to be installed by skilled technicians. For installation, please contact a system integrator or IDK. Otherwise, it may cause fire, electric shock, injury, or property damage. Set the power plug in a convenient place to unplug easily. You can easily unplug in case of any extraordinary failure or abnormal situation, and it also helps for unplugging when you do not use it for a long period. Plug the power plug into appropriate outlet completely. If the plug is plugged incompletely, it may overheat which causes electrical shock or fire. Do not use damaged plug or loosened outlet. Clean the power plug regularly. If the plug is covered in dust, it may cause fire due to reduced insulating power. Unplug immediately if the product smokes, makes unusual noise, or smells. If you continue to use the product under those situations, it may cause electric shock or fire. After confirming that the product stops smoking, contact IDK. Unplug immediately if you drop the product or if the cabinet is damaged. If you continue to use the product under those situations, it may cause electrical shock or fire. For maintenance and repair, contact IDK. Unplug immediately if water or other objects are directed inside. If you continue to use it under those situations, it may cause electrical shock or fire. For maintenance and repair, contact IDK. For connection Instruction Warning Differences in ground potential among the product and external devices may cause electric shock or damage of the devices. When using cables to connect devices, including connection of long-distance transmission, unplug the power cables of all related devices. After connecting signal/control cables of each device, plug in the power cables of each device. 5
Double Pole / Neutral Fusing Caution Electrical Hazard Hot surfaces Caution Do not touch the product s hot surface. If the product is installed without enough space, it may cause failures of other products operation. If you touch product s hot surface, it may cause burn. Do not place the product in any place where it will be subjected to high temperatures. If the product is subjected to direct sunlight or high temperatures, it may cause fire. Do not place the product in humid, oil smoke, or dusty place. If the product is placed near humidifiers or dusty area, it may cause fire or electric shock. Do not block the vent holes. If ventilation slots are blocked, it may cause fire or failure due to internal heat. Prohibition Do not put heavy items on the product. It may fall/turn over and lead to injury. Do not exceed ratings of outlet and wiring devices. If several plugs are put in an outlet, it may cause fire and electric shock. Use only the provided AC adapter and power cable. Do not use the provided AC adapter and power cable with other products. If non-compliant adapter or power cables is used, it may cause fire or electrical shock. Use the supplied AC power connection cable. Do not plug or unplug with wet hands. It may cause electrical shock. No wet hands Instruction Use and store the product within the specified temperature/humidity range. If the product is used outside the range continuously, it may cause fire or electric shock. Turn off devices when they are connected to another device. It may cause fire or electric shock. Unplug the power plug if you do not use the product for a long period. In case of defect, it may cause fire. Unplug Unplug the power plug before cleaning. It may cause electric shock. For installation For rack mount devices: Instruction For devices with rubber feet: Instruction Mount the product to the rack meeting EIA standards, and maintain spaces above and below for air cooling. For your safety, attach an L-shape bracket in addition to the mount bracket kit for the front panel to balance the weight. Never insert only the screws into the holes after removing the rubber feet. It may lead to damage when the screws contact electrical circuit or parts inside of the product. To put the rubber feet back on, use only supplied rubber feet and screws. 6
Altitude: Do not place the product at elevations of 2,000 meters (6562 feet) or higher above sea level. Failure to do so may shorten the life of the internal parts and result in malfunctions. Instruction Fuse (For products having a fuse holder) Products with a fuse holder, the fuse can be replaced with a new one. Follow the detailed procedure indicated in the manual to replace the fuse. In case the fuse blows again even after the blown fuse is replaced, the product may have problems. 7
Table of Contents 1 Included Items... 9 2 Product Outline...10 3 Features...11 4 Front and Rear Panels...12 5 System configuration example...13 6 Precautions and preparations...14 6.1 Attaching Rubber feet...14 6.2 Installation...14 6.3 Cabling...15 6.3.1 Connecting to compatible models...16 6.3.2 Connecting alarm...17 7 Alarm conditions...18 7.1 Overcurrent protection...19 7.2 Fan rotating speed slows down...20 8 Product Specification...21 9 Troubleshooting...22 8
1 Included Items Ensure that all items below are included in the package. If any items are missing or damaged, please contact IDK. PDU-1209 Power cord (5.9 ft./1.8 m) (1) DIN plug DC cable with a lock (4.9 ft./1.5 m) (9) 2-pin terminal block (1) Rubber feet (4) [Fig. 1.1] Included items Note: Follow the instructions below to prevent fire and electrical shock. Do not use any other cables than the supplied DIN-plug DC cable. Do not use the supplied DC cable for purpose other than power supply to the following products: NJR-01UHD, NJR-04HD, NJR-CTB, MSD-402, and HDC-TH200 9
2 Product Outline The PDU-1209 is a power distribution unit that provides power for up to 9 compatible model devices (NJR-01UHD, NJR-04HD, and NJR-CTB, MSD-402, and HDC-TH200). The PDU-1209 has overcurrent protection. If the PDU-1209 detects a power failure or a fan failure, the appropriate front panel LED is illuminated and the PDU-1209 outputs a warning alarm. PDU-1209 PDU-1209 provides power up to 9 channels (DC 12 V 3.3 A) NJR-T01UHD NJR-T01UHD : : : Up to 9 devices [Fig. 2.1] Typical application diagram [Table 2.1] Compatible models Series IP-NINJAR products Other IDK products NJR-01UHD, NJR-04HD, NJR-CTB MSD-402, HDC-TH200 Model number Note: Do not use the PDU-1209 for any purpose other than for power distribution to the products listed above. 10
3 Features Power supply Power distribution for IP-NINJAR products Up to 9 independent 12 VDC and 3.3 A simultaneous outputs Overcurrent protection Others Alarm (in case of excessive DC output current or cooling fan malfunction) DC cable with locking connector 11
4 Front and Rear Panels 1 3 4 5 6 2 7 [Fig. 4.1] Panel drawing (Upper: Front panel, Lower: Rear panel) [Table 4.1] Part names and descriptions Number Name Description 1 POWER switch Powers the PDU-1209 ON/OFF. The POWER LED (green) lights when the PDU-1209 is powered on. 2 DC output connectors Connects to target devices using DIN plug DC cables. When 1 is turned ON, power is supplied to the target devices. 3 ALARM (DC12V) LED Illuminates red if an overcurrent condition causes one or more output connectors (2) to be disabled. 4 ALARM (FAN) LED Illuminates red if the cooling fan fails to operate correctly. See: 7 Alarm conditions See: 7 Alarm conditions 5 ALARM connector Detects abnormalities in the PDU-1209 power and its cooling fan using the supplied 2-pin terminal block. See: 6.3.2 Connecting alarm 6 Frame ground Ground terminal 6 can be used to provide an electrical bond between the PDU-1209 and surrounding equipment ground potential. An M4 screw is used. 7 AC power connector For the supplied power cable 12
5 System configuration example System configuration example: The PDU-1209 is connected to IP-NINJAR series products which are connected to source and sink devices. Blu-ray Player 4K Monitor Fiber optic Fiber optic Blu-ray Player Fiber optic IP network Fiber optic Monitor 10 GbE switch PC for control PDU-1209 can provides power for 9 channels (DC 12 V 3.3A) PDU-1209 can provides power for 9 channels (DC 12 V 3.3A) [Fig. 5.1] Configuration example 13
6 Precautions and preparations Before using the PDU-1209, follow the precautions and instructions below. 6.1 Attaching Rubber feet First, clean the bottom surface of the PDU-1209 as needed, and then peal the release papers from the rubber feet and place them in each of the four corners. 6.2 Installation Follow the instructions below when installing the PDU-1209. Do not place the PDU-1209 on another device directly. The temperature of its bottom surface is elevated after it is powered on. Do not block vent holes. To provide adequate ventilation, maintain sufficient clearances around the PDU-1209 (30 mm/1.18 inches or more). When placing the PDU-1209 in an EIA rack-mount unit, keep 1U or more vertical clearance above and below the unit. Prepare ventilating equipment to keep the ambient temperature at 40 degrees C/104 degrees F or less. If inadequately vented, the life of parts may be shortened and operation may be affected. When you do not use an EIA rack-mount unit, maintain adequate clearances (30 mm/1.18 inches or more) as shown below. 30 mm/1.18" or more 30 mm/1.18" or more 30 mm/1.18" or more [Figure 6.1] Minimum required clearances (when an EIA rack-mount unit is not used) 14
6.3 Cabling Follow the precautions below when connecting the PDU-1209 to target devices. Read the user s guides of connected devices carefully. When connecting a cable to the PDU-1209 or a compatible product, dissipate static electricity by touching grounded metal such as racks before handling single cables. Failure to observe this precaution may result in ESD (electrostatic discharge) damage. Turn off all devices. Be sure to fully seat all plugs and connections and dress cables to reduce stress on connectors. Notes: If you do not follow the precautions above, the PDU-1209 may malfunction or may be damaged. Do not connect the AC adapter that is supplied with the compatible models (NJR-01UHD, NJR-04HD, and NJR-CTB, MSD-402, and HDC-TH200) to a DC output connector of the PDU-1209. Do not connect the PDU-1209 s DC outputs to one another using the supplied DIN plug DC cable. 15
6.3.1 Connecting to compatible models Use a supplied DIN plug DC cable to connect the PDU-1209 to a compatible product. Insert each DC plug into an output connector until it clicks. To remove a plug from the output connector, grasp the plug as illustrated below. PDU-1209 Grasp this part when removing the DC plug. DIN plug DC cable Inserting Removing NJR-T01UHD [Fig. 6.2] Connecting PDU-1209 to NJR-T01UHD 16
6.3.2 Connecting alarm In order to activate the alarm function which warns you of a power failure and a decrease in cooling fan speed, attach the supplied 2-pin terminal block to a cable and connect to the ALARM connector. AWG 28 to AWG 16 conductor gauge is recommended. The maximum wire strip length is 7 mm/0.28 inch. Tighten Loosen 7 mm/0.28 inch MAX. [Fig. 6.3] Connecting 2-pin terminal block 17
7 Alarm conditions The PDU-1209 outputs an alarm when one of the following problems occurs. While the ALARM (DC12V) LED is illuminated, the PDU-1209 automatically interrupts power to the particular DC output connectors with an overcurrent condition. Power is automatically restored, once the overcurrent fault has been corrected. [Table 7.1] Outputting alarm ALARM LED Power supply Problem Stop supplying Malfunction and overcurrent See: 7.1 Overcurrent protection Continues to supply Failure in the fan or rotating speed slows down due to age-related deterioration See: 7.2 Fan rotating speed slows down Note: In case an alarm is output, the PDU-1209 may be damaged. Power off the PDU-1209 and stop using it. Tip: ALARM (DC12V) LED lights if even one DC output connector has an overcurrent condition. Contact Rated voltage: 24 V Rated current: 300 ma Outputting alarm LED lights: A problem occurs LED does not light: No problems occur [Figure 7.1] Outputting alarm 18
7.1 Overcurrent protection Each DC output connector can source up to a maximum rated current of 3.3 A. If a short circuit occurs due to a damaged DIN plug DC cable or if a DC output connector is connected to a device other than compatible products, 3.4 A or larger current may be output. Once an overcurrent condition is detected, the PDU-1209 stops supplying power from the affected DC output connecter temporarily. In order to notify you of the problem, the PDU-1209 outputs an alarm and it lights the ALARM (DC12V) LED. When the overcurrent condition is corrected, the PDU-1209 re-establishes power to the DC output connector automatically. Rated current: 3.3 A 3.3 A or less Over 3.3 A 3.3 A or less Stops power supply [Fig. 7.2] Overcurrent protection 19
7.2 Fan rotating speed slows down If the fan s rotational speed decreases due to age-related deterioration or other causes, the PDU-1209 may not operate correctly. If the fan s rotational speed is insufficient to maintain the correct internal temperature, the PDU-1209 outputs an alarm and lights the ALARM (FAN) LED. 20
8 Product Specification DC power Output Function Alarm output Others Item Number/Signal Connector Number/Signal Connector Power Supply Power consumption Dimensions Weight Temperature Humidity Description 9 outputs/12 VDC, 3.3 A (designated DC cables are supplied) 9 4-pin female DIN Overcurrent protection 1 port/signal in case abnormality of DC output or fan is detected 1 2-pin terminal block AC ~ 100V-240V±10%, 50 Hz/60 Hz ± 3 Hz About 423 Watts 8.27 x 1.73 x 9.84 /210 (W) x 44 (H) x 250 (D) mm (EIA 1/2U rack, projections not included) About 4.9 lbs./2.2 kg Operating: 32 F to 104 F / 0 C to +40 C Storage: -4 F to +176 F / -20 C to +80 C Operating / Storage humidity: 20% to 90% (Non Condensing) 21
9 Troubleshooting In case the PDU-1209 does not work correctly, please check the following items first. Also refer to manuals for connected devices as well, since they may possibly be the cause of the problem. Is the PDU-1209 powered on correctly? Are cables connected correctly? Are there no short circuits, disconnections, or loose connections? Are appropriate cables for PDU-1209 being used? Are there any nearby objects that may cause noise? If additional assistance is required, please check the following items and then contact us. No. Checking items Result 1 Does the ALARM (DC12V) LED light?* Yes or No 2 Does the ALARM (FAN) LED light?* Yes or No *If yes, power off the PDU-1209 discontinue use. 22
User s Guide of PDU-1209 Ver.1.0.0 Issued on: 14 July 2017 Headquarters IDK Corporation 7-9-1 Chuo, Yamato-shi, Kanagawa-pref. 242-0021 JAPAN TEL: +81-46-200-0764 FAX: +81-46-200-0765 Email: idk_eng@idk.co.jp URL: http: //www.idkav.com USA IDK America Inc. Email: sales@idkav.com URL: http: //www.idkav.com 72 Grays Bridge Road Suite 1-C, Brookfield, CT 06804 TEL: +1-203-204-2445 Europe IDK Europe GmbH Lise-Meitner-Str. 6, D-40878 Ratingen Email: info@idkav.eu URL: http: //www.idkav.eu Product information Support Arvanics Corporation 7-9-1 Chuo, Yamato-shi, Kanagawa-pref. 242-0021 JAPAN TEL: +81-46-259-6920 FAX: +81-46-259-6930 Email: info@arvanics.com URL: http: //www.arvanics.com Information in this document is subject to change without notice. All rights reserved. All trademarks mentioned are the property of their respective owners. 23