SERVICE MANUAL WHITE KNIGHT CL43 Reversing Integrated ryer UK 0312 432 15001 Technical ata Exploded Views Wiring iagram Parts List January 2003 4213 094 82521
Service & Repair Information Tumble ryer White Knight CL432 uiltin ryer UK I Technical ata General Frontloading standard door opening builtin tumble dryer model. Forward and reverse tumble. Single or double element heating. Timer control. Induced airflow passes through rear ventilation inlets, over heating element, through drum rear perforations, through laundry load/lint filter, through fan and into the exhaust venting. oor opening direction optional left to right or right to left. Identity Model type, manufacturer source, date and serial number are displayed on a white label revealed when the door is open, below where the filter is located. HA identifies the machines as having been manufactured at the Halifax factory. The 1st & 2nd numerals represent the year of manufacture (e.g. 2004 is represented by 04) The 3rd & 4th numerals represent the month of manufacture (e.g. March is represented by 03). The final 6 numerals represent the main serial number of the machine. All information from this label should be quoted in any service communication. Mains Voltage 220/240V 50HZ Maximum Power Consumption 2450W Approximately Connections Please note; plug not fitted to builtin machines. They are designed to be connected to a double pole switched spur with at least 3mm contact separation with a pilot lamp. The appliance must be earthed imensions Height 87cm (33.9 ) to 89cm (34.7 ) depending on the adjustable feet. Width 59.6cm (23¼ ) epth 53cm (21 ) epth when rear vent hose is assembled 60cm (⅝ ) Weight With packing 32.5kg approximately Without packing 31kg approximately Air Flow 140m³/h with capacity laundry load Grant Hood 2004 Page 1 04/03/2004
II Components rive Motor Permanent split capacitor induction 4 polereversing ⅛HP with heat and current sensitive overload protection. Trip temperature between 125 C and 155 C. Reset 90 C. Winding resistances 41.08Ω and 43.3Ω. 8µF Capacitor. No Load Full Load Power Consumption 110W approximately 225W approximately Current Consumption 0.45A approximately 0.75A approximately Speed 1450 RPM approximately 1350 RPM approximately Heater Power Consumption (determined by programme) Low Setting 1125W High Setting 2250W Temperature Overload Cutout (TOC) (bimetal contacts normally closed) Contacts open 120 C under No Air Flow condition Contacts reset manual operation Inlet (Heater) Thermostat (bimetal contacts normally closed) Contacts open 142 C under restricted air flow conditions Contacts reset 115 C automatically Exhaust Thermostat (bimetal contacts normally closed) Contacts open 60 C under normal air flow conditions Contacts reset 49 C automatically Timer Composite programme timer. Variable time setting up to 128mins plus 12 minutes cooldown Clockwise 5 minutes 46 seconds (heater on except for first and last 2 seconds) Pause 2 seconds (heater off) Anticlockwise 10 seconds (heater off) Pause 2 seconds (heater off) rum rum Wrapper, Front and Rear are manufactured from Galvanized Steel Volume: 105 litres Capacity: 6kg dry cotton Speed: 5059 RPM approximately Rotation: alternating clockwise 5 minutes 46 seconds and anticlockwise 10 seconds Grant Hood 2004 Page 2 04/03/2004
III General Information To assist with part identification, a key number is stated in parentheses after a specific part is mentioned so that it can be located on the Parts List for this appliance and consequently on the Exploded Views. asic Programme After loading damp clothes into the dryer, the door must be closed or the programme cannot begin. Clockwise rotation of the Control Knob (352) closes switch contacts within the Timer (211) to (a) energise the main motor (101) and (b) energise the heater (227). The Timer switch contacts will remain closed until the Timer motor mechanism returns the Control Knob to the 0 position. The contacts controlling heating will open 12 minutes before the Timer Knob reaches the 0 position. This is to allow the circulation of cool air for prevention of creasing to synthetic garments. The Heat Selector Switch (216) provides options for either 1.125kW or 2.25kW heating. Thermal Controls Temperature Sensitive Control Switches are electrically in series with the Heater (227). In most conditions, only the Exhaust Thermostat (229) will operate to control the drying programme (automatic reset). An additional Manual Reset TOC (Thermal Overload Control) (228) will operate when severely restricted or lost airflow conditions exist; i.e. air vents blocked, no motor action, belt has come off etc. This switch can be identified by its red coloured reset button protruding from the ack Panel (413). Grant Hood 2004 Page 3 04/03/2004
IV Adjustments and Recommendations for ismantling To assist with part identification, a key number is stated in parentheses after a specific part is mentioned so that it can be located on the Parts List for this appliance and consequently on the Exploded Views. efore working on the appliance, the external cupboard door must be removed and the dryer pulled out from its recess within the cupboard. Front Access Access to all Control Switches is available after removal of the Top Cover (386). For the removal of the Front Panel (376), oor Microswitch (248), earing Housing (440), Seal (442) and earings (445), the machine should be laid flat on its rear after the Top Cover (386), Top Cover rackets (385) and Plinth (199) have been removed. Withdraw the securing screws from the top of the Control Panel (353) together with all of the screws and fittings in connection with the Front Panel (376) and the oor Assembly (203). The Front Panel can then be detached from location lugs with the Control Panel (353) and Cabinet (196). The anjo Assembly (440) has a location lug with the Cabinet (196) base. It can be lifted out following disengagement of the following: Exhaust Thermostat (229), Venting racketry (437) and Fan Housing Cover (447). Rear Access Upper For removal of the combined ack Panel (413) with Heater Unit (227), rive elt (125), rum (266), rum earings (445) and rum Front Seal (442). Remove the Top Cover (386) and withdraw the main Wiring Loom connections from the Terminal lock (142) and Heater terminals. Lay the machine flat on its front, supported to take the weight off the door and controls. With the exception of 4 screws positioned in shallow recessed channels projecting radially from the panel centre, remove all other screws in the ack Panel (413). Lift off the ack Panel (413), which will then allow access to the Heater Assembly (227), Inlet Thermostat (230) and Manual Reset TOC (228). Lift out the rum (266) and rive elt (125) after removing the ack Panel. The rum Front earings (445), rum Seal (442) and oor Microswitch (248) also become accessible at this point. For dismantling of the rum Rear earing (270), access to screws is through holes in the rum rear. Removal of one screw and the Earth Finger provides access to the earing Shaft screw. Note; it is important that the slot in the head of the shaft centre screw is filled with electrically conductive grease. Rear Access Lower The Access Panel (402) to the lower rear of the dryer only needs removing for access to the Motor (101) and associated parts, the Exhaust Thermostat (229) and Venting racketry (437). To remove the Motor Assembly (101), withdraw the Motor racket (432) securing screws from the Cabinet (196) base, remove the Screw from the Fan Cover (447) and exert anticlockwise force to disconnect if from the Fan Housing (446). The Motor Assembly can then be withdrawn. Grant Hood 2004 Page 4 04/03/2004
Exploded View 1 211 450 235 391 449 353 352 386 196 369 248 203 201 362 203a 359 355 363 363a 367 366 365 364 370 376 199 199a
Exploded View 2 445a 248 440 441 442 454 447 445 446 447a 537a 448 456 457 458 459 437 229
Exploded View 3 270 444 266 395 227 390 230 125 141 142 408 228 413 400 399 393 427 446 112 447 101 432 437 402
Wiring iagram F/E 1.25 EC Timer F/E 11 12 A 1 2 3 4 5 6 7 8 9 10 11 12 Mains Cable G Timer Connections A C A/K /K G E TL TN G* 1.0 /K G C 0.75 HESW S A 0.75 MAN TOC HE2 HE1 G* 1.0 A* /K G INTH A* 3 4 C9 C10 9 10 T4 M 3 4/7 5/8 A/K 6 5 7 8 2 1 C11 C12 EXTH Wire Colour Code A C E F G H K N/A lack rown Red Orange Yellow Green lue Violet White Pink A/K E Component Code T S M EXTH INTH HE HESW MAN TOC A/CSW E M CAP E Terminal lock oor Switch Motor Exhaust Thermostat Inlet Thermostat Heater Heat Switch Manual Reset Heater Cutout Anticrease Switch
White Knight CL432 Reversing Integrated ryer Parts List Item escription Code Expl.View 101 Motor & 8µf Capacitor Assembly 4213 092 25611 3 102 Pulley 4213 075 13931 3 112 8µf Capacitor 4213 092 08091 3 125 rive elt 4213 092 18601 3 141 Mains Cable (no plug) 4213 076 33051 3 142 Terminal lock 4213 078 44613 3 196 Cabinet Assembly 4213 092 17761 1 199 Ignis Plinth 4213 092 35741 1 199a Metal Plinth 4213 081 11401 1 203 Complete Flatline oor/window Assembly 4213 092 17181 1 203a Flatline oor Frame Assembly 4213 092 28191 1 211 Timer EC4818.01A 4213 078 54781 1 227 Heating Element 4213 092 05521 1 228 Heat TOC 4213 078 50161 3 229 Thermostat (exhaust) 4213 078 48373 2 230 Thermostat (inlet) 4213 078 56261 3 235 Rocker Switch 4213 078 51061 1 248 Microswitch/racket Assembly 4213 092 05251 1 & 2 266 rum Assembly 4213 092 05531 3 270 rum Shaft/earing Kit 4213 092 05591 3 352 Timer Knob Assembly 4213 092 38521 1 353 Control Panel Assembly 4213 092 38531 1 355 Hinge Cover 4213 077 43113 1 359 Flatline oor Hinge Assembly 4213 092 04751 1 362 Window 4213 077 44093 1 363 Flatline oor Frame 4213 077 43104 1 363a Flatline oor Handle 4213 077 44444 1 364 Latch Pivot 4213 075 13013 1 365 Latch Spring 4213 075 70833 1 366 oor Latch 4213 077 53413 1 367 Switch Strike 4213 077 83571 1 369 Loom Clip 4213 075 70941 1 370 Latch Guide 4213 077 40992 1 376 Front Panel Assembly 4213 092 38541 1 & 2 386 Flat Top Cover Assembly 4213 092 38311 1 390 Gasket 4213 074 50862 3 391 Rocker utton 4213 077 53462 1 393 Flex Support Clip 4213 077 40982 3 395 Heater Wires Clip 4213 075 70971 3 399 Heater Support 4213 080 06618 3 400 Heater Plate 4213 070 0648A 3 402 Access Panel 4213 070 06555 3 408 Cable Clamp 4213 078 47303 3 413 ack Panel Assembly 4213 092 37601 3 427 Motor Spring Clip 4213 078 45361 3 432 Motor Mount racket 4213 080 06756 3 437 Extendable Rear Vent Kit (short) 0312 002 01000 2 & 3 440 anjo Assembly 4213 092 17811 2 441 Front earing (short) 4213 077 40952 2 442 Front Seal 4213 077 61701 2 444 Lifter 4213 077 41009 3 445 Front earing (long) 4213 077 40962 2 445a earing Pads & rush Seal Kit 4213 092 21171 2 446 Fan 4213 077 40895 2 & 3 447 Access Cover Assembly 4213 092 18081 2 & 3 448 Spring Clip (Fan) 4213 075 71162 2 449 utton Switch Spring 4213 075 71151 1 450 Switch racket 4213 070 09244 1 4213 094 82521
White Knight CL432 Reversing Integrated ryer Parts List 454 Filter 4213 092 17821 2 455 Screw 6 x 10 Countersunk Head 8213 130 30971 2 456 anjo Seal 4213 077 07991 2 457 J' Clip 2513 482 08002 2 458 anjo Insert No 2 White 4213 077 40962 2 459 anjo Insert No 1 White 4213 077 40952 2 471 U' Type Captive Nut 2513 483 12036 2 537 W' utton Plug 4213 078 26311 2 Not Shown On Exploded Views Loom Assembly 4213 076 43571 User Instruction ooklet 4213 094 82022 MFI Fittings (Pair of Hinges, oor Stop, Spacers etc.) 4213 089 30281 4213 094 82521