QuadraTouch Pro Software Update Change Log Official Release vs. Beta Release (How to tell): Tools -> System Tools -> System Information and look for Official Release or Beta Release in the bottom right hand corner Known Issues: No Currently Known Issues V1.21: (Required for All Dryers with Static Sampler or Incoming MST Sensor, Good for All Dryers) NOTE: Required for all New Touchpanels (Rolling change 2018) New Touch Panel Back (BL2) Old Touch Panel Back Adjusted Several Functions to ensure proper operation on the BL2 Touchpanel Corrected Issue with Incoming Moisture Calibration (2 of 2) In Manual Operation you can now set the metering rolls anywhere between 0 and 100% regardless of Max/Min Limits. (Cross-Flow/Mix-Flow) Corrected Issue with Static Air Pressure Switch for Fan 1 not logging right for History Log. (Cross- Flow/Mix-Flow) Corrected Issue with User Unload Delay Timer always tripping at 2 minutes regardless of setting. (Cross- Flow/Mix-Flow) Made adjustment to Moisture Loop Calculations making it quicker to respond when near a roll limit. Enabled Multilingual Support for BL2 Touchpanels. Strings updated to Version 1.06 NOTE: A few dryers were shipped from the plant with the Beta Version 1.21 Release, they have strings version 1.05. No Major Difference other than Multilingual Support is disabled. V1.20: (Required for All Dryers with Static Sampler or Incoming MST Sensor, Good for All Dryers) NOTE: NO LONGER REQUIRED to leave the TouchPanel on for 65 minutes after doing an update. Corrected issue with Static Sampling Replaced a file that was falsely flagging on some antivirus programs. Corrected issue with Incoming Moisture Sensor Calibration/Readout. (1 of 2) Updated History Log to include all alerts even when multiple faults are present. Added button to allow you to search for all times an alert has been logged.
Fixed issues with Faults on Tower Dryers based on Tower Dryer Model Choice. Fixed issue with Stabilization Time Calculation on Plenum 2 for Crossflow Dryers. Updated Strings File to 1.03 Added Calibration Offsets to the Data Log V1.19: (Required for All Dryers V1.15 to V1.18) Corrected issues with New Moisture Formulas/Calibration including Celsius Conversions Fixed Static Sampling on Portables not displaying when to sample. Repaired issue with 1 Fan Tower Fan Shutdown Delay Added Reduced Torque Starting Support for Towers V1.18: (Required for 1 Fan Tower Dryers V1.15 to V1.17) Corrected Tower Dryer PLC Issue where Single Fan Towers won t power main gas valve. (V1.15 V1.17) Lowered Discharge Moisture Setpoint minimum limit to 8% in order to allow for Canola. Added check for Stuck Screen on User Reset V1.17: Corrected PLC Bus Diagnostic not showing proper PLC Bus Structure (Cosmetic Only) Corrected issue with Network Repair Utility not properly naming the adapters. (Cosmetic Only) Corrected Analog Sensor not found Border. (Cosmetic Only) V1.16: Corrected PLC Software Compiling Issue only 1 Fan would start (V1.15) V1.15: NOTE: After updating to a Version greater than V1.15 you need to leave the Touch Panel on for at least 65 minutes. This will allow the database to fully rebuild. If you do not, it will do a Set Defaults procedure every time you power up the Touch Panel until it has had at least 65 minutes to run. Other than you having to change the settings to desired settings and recalibrate, it will not prevent you from running the dryer. Load Delay has been changed to delay the starting of the load auger and load auxiliaries, instead of just the load auxiliaries. It will now be the time delay between when the dryer calls for grain (paddle switches down) and when the load system starts. Strange I/O combination time for #94 has been extended to accommodate conveyor unload systems. Discharge Calibration procedure has been modified for portable dryers with static samplers. Fixed Bushel Counter in Automatic.
Discharge Minute Average/Sample Average has been added to portable dryers when static sampling is enabled. Also added to Remote App Display. Static Sampler error will not come up when static sampler not enabled. Added option to manually run setupnp script in Network Configuration. Change Meter Roll speed in remote access app added under grain details tab. Device ID generator modified for exceptions if your system is only generating a 7-character Device ID. Added OPC Server Maintenance feature in Maintenance Tools. (Auto Heal OPC server and install correct settings) Changed Communication Error flashing in header will direct you to communication error page (.pdf troubleshooting access) Added Kill Top Most feature to maintenance tools page. Will stop the TopMost app for 10 minutes to give better focus/control of applications running in the background. Added button in Maintenance Tools to reload the main script in the event of script error. Discharge Control Method fixed in continuous flow. Added Public IP popup Added script that automatically checks networking adapters for correct configuration during loading sequence. Added Network Diagnostic tool to help in remote access situations. Fixed Out of Wet Grain Timer for Grain Transfer and Added Separate Fill Timer for Grain Transfer Fixed Initial Fill Timer Fault Fixed Strange I/0 for Multi Fan Dryers Added Disable Moisture Sensor Analog Sensor Not Found Warning. Resets Automatically each time dryer is reset. Fixed/Updated Graphs to Improve Performance Added Network Repair Utility to diagnose and repair most common problems for Communication Error. Major changes to system to improve responsiveness. Added Grain Type Selection for: Corn, Soybeans, Canola, Hard Red Winter Wheat and updated the moisture calculation formulas for improved drying accuracy. Metering Roll Fault is now enabled on Mix Flow/Static Sampler Dryers. Combined Tower and Tower 10k PLC Programs. When updating PLC it no longer asks if it is a 10k Dryer. Updated Several PDF Files and added Portables Ladder Diagram Drawings.
V1.14: Pin Assignment change for 1 Fan Dryers with Incoming moisture Sensor (additional green card) Signal D5 Changes from 1.1 to 2.1. Adjust Roll Speed limits from continuous flow page fixed Adjust roll speed limits in manual control changes current manual roll speed if outside limits New popup keypad added for numerical values Tower Discharge Method Pop-up Added Confirmation screen added for switching into manual control from automatic Bushel Counter Ratio was not retained during shutdown fixed. Desktop Application for remote viewing added to project directory (requires Java). Remote Access Subscription Keys activated for smart phone and pc remote access. Ask your Sukup dealer for a remote access key (requires dealer activation). No restart required during software update. Software simply reloads itself Tower Dryers: Fan Shutdown Delay timer now always shuts off heater system during fan shutdown delay. Auto Update Feature. If the QuadraTouch Pro system is connected to the internet, it will periodically check for software upgrades, and download new versions automatically when available. Added Public IP display to Auto Update Page Added Discharge Moisture Alarm in Tools Menu. (Optional Fault Shutdown) Added Static Sampling to Portable Dryers. Configure in System Tools. (Optional Fault Shutdown) Added Networking Configuration Page to Maintenance tools. User adjustable Grain Transfer Out of Wet Grain Timeout added Added Recent Data Log to Graphs page. Graphs Containing the Actual Input Moisture have been switched from real-time to 1-min avg values. User Fault Text is now user selectable/editable in System Tools Menu. Pop-up reminder added to clean dryer and check sensors. Analog Signal Problem Reminder added to the header. Also prevents accessing automatic from manual mode. Screen will pop up only once. It will then stay Red in the header until the problem is fixed. Touch the Analog Sensor Missing message to pull up the Analog Sensor Missing screen.
Lock-Out Screen Added to System Tools Menu. QuadraTouch Pro is now configured for plug and play remote access. A Text Messaging notification Feature is also available for those who purchase remote access subscription keys. Purchase your remote access key through your Sukup Dealer. Mix Flow Dryer support added. Static Sampling for Portable Dryers added. Video Troubleshooting and support for Tower Dryers added. Updated.pdf content V1.13: Added EMOV position graphs Added Column Temp Graphs Tower Diagnostic page: #35 Customer Unload Interlock indication fixed Added Load Delay Visual timer to Tower Dryer Running Screen. Added Tower Static Sampling Error Pop-up Screen. Changed Default Value for Moisture Gain to 60. Changed Default Flame Timer for Towers to 300 sec. Pressure Transducer Values fixed for Auxiliary Device. Autobatch Time/Temp discharge fixed. Warm Up option added to Restart with Stabilization mode Provided Pop-up window for discharge method selection in continuous flow operation Program Updates after V1.13 will automatically reboot the PLC and HMI after program download. Added Manual scripted file transfer in APPS directory (for manual software transfer, refer to web instructions). Fixed Tower Fan Start Delay Timer 4 Fixed Tower Load Interlock #34. Also displays pop up when applicable. Grain Transfer added apply speed change button Added Fan/Model selection to system information page Added Update Instructions to QuadraTouch Update page Added Restart OPC server to Maintenance Page.
Strange I/O Combination shows trigger condition (why it had a strange I/O combo) and if the condition is still present. Changed Communications Timeout to 30 seconds from 20 seconds. Simplified input moisture calibration (if applicable). V1.12: Only necessary for Tower Dryers, no modifications made for 1-6 fan dryers Tower Modifications Calibration procedures for discharge and incoming moisture changed for static sampling. User auxiliary load and unload timers fixed Tower Diagnostics added / refined MST actuator and prox switch lights fixed. Added Maintenance tools button to communication error page Added 1 minute discharge average to running screen. Added Control Sample Average to running screen. This is the value used for MST control. Added.pdf for LME69 and SQM 50 Actuator V1.11: Improved program performance Remote client app support -Requires onsite internet access, free app download, and purchased license key T7101 Added Prox Switch Override button to admin tools page Complete wiring diagrams can be accessed on fault monitoring page Plenum > 275 degrees fault has been added to individual plenum fault menus Tower air switch strange I/O combo extended to 5 minutes Changed EMOV low fire position values for Tower Dryers Added 15 sec EMOV delay Added Column Temp Override Pins #246 and #243 were programmed backwards. No wiring changes are necessary Added.PDF content for Tower Dryers Added end of season maintenance notes for Tower Dryers Expanded Plenum Temperature Range for Tower Dryers Input MST control Enable / Disable button added to the Admin Tools page
Tower Diagnostics Page Link fixed