Version: MS1 GSM Emergency Alarm User s Manual For a better understanding of this porduct,please read this user manual thoroughly before using it.
CONTENTS CONTENTS Ⅰ. Introduction Ⅱ. Product Appearance Ⅲ.Interface Description Ⅳ.Installation Notes Ⅴ.Host settings 1.Start up Status 2.Manual Recording 3.Remote Control Code 4.Zone Code 5.Host SOS Button 6.Call/Answer Alarm Status Operation Ⅵ. 1.Enter Settings 2.Restore Factory Settings 3.Modify Password 4.Language Settings 5.Alarm Phone Settings 6.Delete Alarm Call 7.SMS and Phone Settings 8.Delete SMS and Phone 9.Zone Programming 10.Zone SMS Program 11.Home Arm Settings 01 01 03 03 04 04 05 05 06 07 07 07 07 07 08 08 08 09 09 10 10 11 11 12.Siren Tone 13.SMS Reply Switch.Remote Control Delayed Protection Switch 15.Delay Arm, Delay Alarm, Alarm Response Time Settings 16. Host IMEI Code Query 17. Host Status Query 18. System arm 19. System disarm 20.Home arm 21.Monitor 22.Intercom 23. Set the built-in launch encoding 24. The Host Version Query 25. GSM Signal Query 26. Restore Factory Settings Ⅶ.technical parameter Ⅷ.Basic Configuration 12 12 13 13 15 15 15 15 18 19
Introduction Ⅰ. Introduction Support 30 wireless detectors, 1 Wired zone (normally closed), 1 SOS button on Panel, 8 remote controls. 4 LED indicate Main Panel Status. Preset 5 groups of alarm phone numbers, the Main Panel automatically dials phone to make alarm. Note: You can download "MS1"from Google play on Android phones, and download "MS1" from the "App Store" on Iphones to control the host. Preset 5 groups of SMS numbers for automatically sending alarm message. 10s manual alarm voice recording. 1 switch (normally open) output alarm. Built-in Chinese and English text messages, bilingually optional, automatically send messages when alarm. Away arm,home Arm, Delay Arm, 24 hours, Close functions optional. Wireless coding to add sensors efficiently. Make call to the Main Panel to remotely program the Main Panel. Built-in 500mA rechargeable lithium battery for backup when external power off. External power off /on message Alert. All settings can be done by SMS. Ⅱ. Product Appearance
Product Appearance Interface Description Ⅲ.Interface Description REC CODE GND Z1 COM NC DC/12V SIREN PORT WIRED PORT SIM SLOT LED1 LED2 LED3 LED4 LED5 POWER ZONE STATUS SIGNAL ALARM ALARM Alarm Indication:When there is an alarm light flashing rapidly. SIGNAL No GSM Signal, light on one second then off, when GSM network's normal--light on 0.5 second and off 3 seconds; if there is any wireless sensors sending signal-light on and blinks twice on the end. STATUS Status Indication: at the begin of entering settings status--light flashing rapidly, Host disarms--light On for a second and off for one second, Host Arms--stay on, Host arms at home--breathing light. Zone Sensors coding indication: Click the code key to access remote controller coding--light flash rapidly, click again to enter Sensors coding -light stay ON, remotely control--breathing light. POWER Power supply: external power on Light stays ON, no external power and the Panel running by battery--breathing light. Delay alarm-- breathing light, no disarm after alarm light on for 0.5 seconds, off 3 seconds to mention there is an alarm. Ⅳ.Installation Notes Note: Short press code key to turn on, long press to turn off. Hosts should be installed in the center of prevention sites to accommodate all wireless detectors for the best reception.note that the host should be installed as far as possible from large metal objects or appliances with highfrequency disturbances, and keep away from reinforced concrete walls and fire doors,etc.
Host settings Ⅴ.Host settings 1.Start up Status Firstly insert a SIM Card into the Host, and connect Adapter external Power, All LED will be on for 2s, and there will be a beep, the Host is on. When the Host is running by Back-up battery only without AC power, press the Code button until 1 long beep and 3 short beeps, release, the host is OFF. Quick press the code key again, then host is on again. ALARM Alarm Indication:When there is an alarm light flashing rapidly SIGNAL No GSM Signal,light on one second then off, when GSM network's normal--light on 0.5 second and off 3 seconds; if there is any wireless sensors sending signal-light on and blinks twice on the end. STATUS Status Indication: at the begining of entering settings status-- light flashing rapidly, Host disarms-- light On for a second and off for one second, Host Arms--stay on, Host arms at home--breathing light. Zone Sensors coding indication:click the code key to access remote controller coding -light flash rapidly, click again to enter Sensors coding -light stay ON, remotely control--breathing light. POWER Power supply: external power on Light stays ON, no external power and the Panel running by battery--breathing light. Delay alarm-- breathing light, no disarm after alarm light on for 0.5 seconds, off 3 seconds to mention there is an alarm. Note: When there is no external power, and the panel is under Disarm status, long-press code button until 4 beeps, POWER OFF. Click Code button again and the power will be ON. This function do not exit when there is external power connected. 2.Manual Recording In disarm mode, click the "RECORD" button on the side of the host, one beep sound indicates the recording begins; Please stay 30cm away from the host, use middle voice and standard Mandarin to record user information, during the process, press the "RECORD" button will immediately end the recording for playback, without pressing button 10 seconds later, the recording ends and automatically play recording. Operation Method: Click record button on the side of host. Note:Do not hold. 3.Remote Controller Coding In disarm mode, click the "CODE" button on the side of the host, host "beep" one sound, [Zone] light flashes rapidly; take a remote controller,and press any key of it to trigger the wireless signal,once the host received signal,sounds a long "beep", indicates remote controller coding successfully. If repeat on coding, it would appear two short "beep" sound, Status light flashes rapidly, in coding mode, it can continue to code more Remote Controllers. Operation Method: Click the the " CODE " key on the side of host. Note: Host up to code 8 remote controllers, the first remote control transmits wireless signals is "1 remote control",and so on, continuously on coding. Delete remote controllers: Host settings In remote control status,hold the" CODE " button on the back of host for 3s, the host sounds a long "beep", which indicates that all remote controllers coded have been deleted successfully. Operation Method: In remote controllers coding status, hold the" CODE " button on the back of host for 3s. 04 05
Note: Once remote controllers are deleted, you cannot take any remote controller to control the host. Exit Coding: In remote controllers coding status, click the "CODE" button twice, [Zone] light turns off, exits code status. 4.Zone Coding In disarm status, continue to press the "CODE" button in the back of host twice, the host beeps twice, while ZONE light on, take detectors need to code (one or more), trigger detector to send a wireless signal to the host. After received it, the host beeps once Indicating wireless detector coding successfully. It will beep twice when repeat coding. 30 detectors codes can be superimposed in a row. In code mode, it can continue to code. Host settings Delete zone coding: In zone coding mode, hold the "CODE"button on the back of host for 3 seconds, the speaker beeps once indicating all zone accessories have deleted successfully. Deleting zone is not valid when alarming, so please make sure before deleting. Operation Method: In zone coding status, hold the "CODE " button on the side of host for 3 seconds; Note:Once the wireless detector was removed, it can no longer trigger the host alarm. The front 5 probes of SOS host is 1-5 zone, back code 6-30 is 6th zone. Exit Coding: In remote control code status, click the "CODE " button twice, [Zone] light turns off, exit code status. 5.Host SOS Button: It is the 8th zone of host, touch to send SOS alarm, hold to disarm. 6.Call/Answer Alarm Status Operation: After receiving the call, enter on the dial pad of phone: 1#:Arm 2#:Disarm 3#: Home Arm 4#:Monitor 5# : Intercom Ⅵ. All programming of the hosts are made by telephone (mobile phone) to call host SIM card number, or by mobile phone text message. 1.Enter Settings Make call to SIM Card in Host, the call will automatically get through and there will be 2 beeps, now input Password (Factory Default 123456) and press # button to confirm, there will be a long "beep ", Status LED on Host will rapidly flash, the Host enters setting status. Note: 1 If you enter the wrong password, two short "beep" prompt the error, typing three errors, the host automatically hang up. 2 In setting status, you can repeat a number of feature sets, if you stopped host operation for more than 60 seconds, the host will automatically exit Setup. 3 In remote programming status, hangs the phone directly to exit the setting status. The following instruction distance text message settings and telephone remote settings is universal. The following SMS instructions are in the factory password (123456), after changed the password, subject to the user's passwords. 2.Factory Reset If you forget setting like Password, or the Host is not working normally, it 06 07
is suggested to make Factory Reset. Under Disarm Status, long press Recording Button for 3s until 1 beep, all Indicator LED will be on. 3.Modify Password In settings mode, firstly press [10] key on your telephone keypad, then press the [*] key, enter the six-digit password, at last press the [#] key to confirm; host "beep" once indicates password changed successfully. Setting method: [10][*] [XXXXXX] [#] XXXXXX represents the six-digit new password For example: Modify the password to 123123; Operation Method: 123456#10*123123# 4.Language Settings In settings mode, firstly press [10] key on your telephone keypad, then press the [*] key, input [0]-[1],at last enter [#] to confirm; the host "beep" once indicates successful language settings, "0" means Chinese, "1" for English. Setting Method:[11][*] [X] [#] X is for language selection For example: Change the language to Chinese, a specific operation; SMS operations: 123456#11*0# 5.Alarm Phone Settings In settings status, enter code [20] key on the phone keypad, and then enter the [*] key, then enter "01"-"03" key, and enter the [*] key. Then enter the phone (telephone) number and press [#] button to confirm, the host "beep" once indicates phone number set successfully. Setting Method:[20][*][Y][*] [ZZ ZZ] [#] Y represents: 1st to 3rd set of telephone codes for police. ZZ... ZZ represents: Setting phone (cell phone) number. For example: Set 13811111111 as the first group alarm phone number. Operation Method: [20][*][01][*] [13811111111] [#] SMS operation: 123456#20*01*13811111111# 6.Delete Alarm Call In settings status, enter code [20] [*] key on the phone keypad, then type [01]-[03] [*] key, at last, [#] key to confirm, the host "beep" once indicates phone number deleted successfully. Setting Method:[20][*][X][*] [#] X represents: 1st to 3rd set of telephone codes for police. For example:delete the third group of telephone number from the host. Operation Method:[20][*][03][*] [#] SMS Operation: 123456#20*03*# 7.SMS and Phone Settings When Alarm System send messages to alert, there're totally 3 groups of number that be sent with alarm messages(such as: fifth zone, balconies alarm). In Settings Status, enter code [21] [*] key in the telephone keypad,, then type [01]-[03] [*] key, then enter the user's phone number and enter [#] key to confirm. The host of "beep" once indicates SMS numbers set successfully. Setting Method:[21][*][Y][*] [ZZ ZZ] [#] Y represents: 1st to 3rd set of telephone codes for police. 08
For example:set 13822222222 as the first group of phone and SMS. Operation Method: [21][*][01][*] [13822222222] [#] SMS Operation: 123456#21*1*13822222222# 8.Delete SMS and Phone In Setting status, enter code [21] [*] key on the phone keypad, then type [01]-[03] [*], [#] key, the host "beep" once, while [RF] light flashes, phone number deleted successfully. Setting Method: [21][*][X][*] [#] X represents : 1st to 3rd set of SMS codes For Example: Delete 3rd SMS number from the host. Operation Method :[21][*][03] [*] [#] SMS Operation: 123456#21*03*# 9.Zone Programming (only supports SMS settings) When users need to change the properties of zone alarm, for example: alarm without siren and so on, can be realized by zone programming. Enter the address number [60*] key by SMS, enter [1~7*] zone number, then enter [1~4*] zone type, and then select [0/1*] siren whether sound, then enter your custom message, add [#] confirmation (if you do not enter a custom message then, zone 1 alarm is default message. Setting Method: [60][*] [A][*] [B][*] [C][*] [D] [#] A Zone No.:"1~6" corresponding to wireless zone 1 to 6, note 6 zone for 6-30 detectors. "7" corresponds to 1 Wired zone. "8"corresponds to host SOS button,can be set with or without a siren,cannot set the zone type. B Zone Type: [1] General Zone, [2] Zone delay for 40 seconds, [3]24 hour Zone, [4] Close Zone. C Alarm Mode: [0] for the silent alarm [1] for the audible alarm. The default is audible. 10.Zone SMS Program (only supports SMS settings) When users need to change zone alarm SMS, for example: Enter the address number [62*] key by SMS, first enter [1~8*] zone number, then enter custom SMS, add [#] to confirm(if you do not enter a custom message or the default message is "1 zone alarm"). A Zone No.:"1~6" corresponds to wireless zone 1 to 6, note 6 zone for 6-30 detectors. "7" corresponds to 1 Wired zone. "8" corresponds to host SOS button. B Zone SMS:Supports up to Chinese characters or 32-bit 8 letters/numbers input. For Example:Set 1 zone to alarm SMS: Balcony alarm SMS Operation: 123456#62*1*Balcony alarm# 11.Home Arm Settings When you want to make part of the detector work, another part of the detector does not work, you can use [home protection] feature to implement, but at home zone needs to be set. In Settings status,enter code [61] key on the phone's keypad,then enter the [*] key, select zone code [1~7] key, and then enter the [*] key and select the zone [Home Arm ], whether alarm [0/1] key, at last press the [#] key to confirm.the speaker "beep" once indicates set successfully. Settings Operation: [61][*] [X][*] [A] [#] X represents:[1~6] corresponds to wireless zone 1 to 6. [7]corresponds to 1 wired zone.
A represents: [0] is for Home arm without alarming, [1] is for Home arm with alarm ing. Factory default is [0] For Example: Set Zone 1 for home arm with alarm ing. Operation Method :[61][*] [1][*] [1] [#] SMS Operation: 123456#61*1*1# For Example: Set Zone 2 for home arm without alarm ing. Operation Method :[61][*] [2][*] [0] [#] SMS Operation: 123456#61*2*0# 12.Siren Tone In settings status, enter code [75] key on the phone keypad,then enter the [*] key, and then select the host arm/disarm operation. Turn off/on external siren by [0/1] key, press the [#] key to confirm. Speaker "beep" once indicates set successfully. Setting Method : [75][*] [A] [#] A is for: [0] close arm/disarm siren tone, [1]open arm/disarm siren tone; factory default [1] open. For example: Open arm/disarm siren tone Operation Method:[75][*] [1] [#] SMS Operation :123456#75*1# 13.SMS Reply Switch In settings mode, enter code [75] key on the phone keypad,then enter the [*] key, and then select the host arm/disarm operation. Turn off/on external siren by [0/1] key, press the [#] key to confirm. Speaker "beep" once indicates set successfully. Factory default [1] open. Setting Method : [52][*] [A] [#] A represents: [0] represents SMS reply closed,[1] represents SMS reply open; Factory default is [1] open. For Example: Turn off SMS reply. Operation Method: [52][*] [0] [#] SMS Operation:123456#52*0#.Remote Control Delayed Arm Switch (for all remote control) In settings status, enter code [53] key on phone's keypad,then enter the [*] key, and then select the arm key to turn off/on time delay function by pressing[0/1] key, then press the [#] key to confirm. Speaker"beep" once indicates set successfully. Setting Method:[53][*] [A] [#] A is for: [0] delay closing, [1] delay opening; the factory default is [0] off. For Example: open delay function of remote control. Operation Method:[53][*] [1] [#] SMS Operation:123456#53*1# 15.Delay Arm, Delay Alarm, Alarm Response Time Settings In settings status, enter address code [54] key on phone keyboard, then enter [*] key, then select away arm delay time and enter two bit digital "AA" key, enter [*] key again. Then select alarm delay time and enter two digital "BB", enter [*] key again.select alarm response time and enter two digital "CC",press [#] key to confirm. Speaker "beep" once indicates set successfully. Setting Method: [54][*] [AA][*] [BB][*] [CC] [#] AA represents: Delay arm time, range 00-99 s, playing default to 10 s BB represents: Delay alarm time, range 00-99 s, playing default to 40 s CC represents: Alarm response time, range 00-99 s, playing default to 3 minutes.
For Example: Settings Method: Delay arm time of remote control is 10s,Delay alarm time is 40s, siren response time is 3 minutes. [54][*] [10][*] [40][*] [03] [#] Settings by SMS : 123456#54*10*40*03# 16. IMEI Query (Only supports SMS settings) SMS Operation: 123456#65# Cellphone Will receive the following 15 digit IMEI code. IMEI:XXXXXXXXXXXXXXX 17. Host Status Query (only supports SMS settings) SMS operations: 123456#63# Cellphone Will receives the following host status System arm System disarm 18. System arm In alarm or setting status, enter "1#" on the phone's keypad. SMS command: 123456#1#= 19. System disarm In alarm or setting status, enter "2#" on the phone's keypad. SMS command: 123456#2# In alarm or setting status, enter "5#" on the phone's keypad. 23. Set the built-in launch code In setting status, enter [70] on the phone's keypad, then enter [*], then enter [X], then enter the address code AAAA(0~9), and then enter [#] to confirm. Beep once, set successfully. Setting Method: [ 70 ] [*] [ X ] [*] [ AAAA ] [#] X represents: 1 means turn on, 0 means turn off. AAAA represents: launch address code. Operation Method: [ 70 ] [*] [ 1 ] [*] [ 8888 ] [#] SMS Operation: 123456#75*1*8888# 24. The Host Version Query (Only supports SMS settings) SMS operation: 123456#66# Mobile phone will receive the following:cn-txx-v0001 25. GSM Signal Query (Only supports SMS settings) SMS operations: 123456#67# Mobile phone will receive the following:gsm Signal:25 26. Restore Factory Settings When the system is unstable, or forget the previous setting parameters, advise the user to restore factory settings, then set the host again. In disarm status, long press the " RECORD " button, then with a long 20.Home arm In alarm or setting status, enter "3#" on the phone's keypad. SMS command: 123456#3# 21.Monitor In alarm or setting status, enter "4#" on the phone's keypad. 22.Intercom Restore Factory Settings In disarm status, long press the record button S3 until hear long "beep" and all indicators on. In disarm status, Restore factory long press the settings,all settings record are cleared. button S3 until hear long "beep" and all indicators on.
Modify Password 123456#10*888888# 10*888888# Setting the Language Modify alarm phone number Delete alarm phone number Modify SMS Number 123456#20*01*# 20*01*# Delete the phone number. 01 for the first group, totally 3 groups. 123456#21*01* 13811111111# 21*01* 13811111111# Modify the SMS number. 01 for the first group, totally 3 groups Delete SMS Number 123456#21*01*# 21*01*# Delete the SMS number. 01 for the first group, totally 3 groups Zone Setting Programming 123456#11*(0-1)# 11*(0-1)# 123456#20*01* 13811111111# 123456#60*1*3*1 # 20*01* 13811111111# NO Modify Programming setting code 0 is for the Chinese, 1 for English Modify the phone number. 01 for the first group, totally 3 groups. Zone number (1-6- wireless zone 7 wired zone.8 is a button ( Note: zone 8 is not affected by zone properties ), ( Zone type: [1] Instant zone, [2] delay for 40 seconds, [3] 24 hour Zone, [4] Closed zone. ), Having siren or not ( [0] for alarm silently, [1] for alarm acoustically ), the front 5 probes is for 1-5 zone, 6-30 is for the 6th zone. Zone SMS programming Home Arm Zone Settings Siren alarming tone SMS Reply Switch Remote Control Delay Arm Switch Delay Arm Time Settings IMIE code Query 123456#62*1*SOS 123456#61*1*1# 61*1*1#Home Home arm with alarm arm with alarm 123456#61*1*0# 61*1*0#Home arm Home arm without alarm without alarm 123456#75*1# Siren on 123456#75*0# Siren off 123456#52*0# Reply on 123456#52*1# Reply off (Default) 123456#53*1# Delay Arm on 123456#53*0# Delay Arm off (Default) 123456#54*10*40*03# Delay 10 seconds ; Not delay 40 seconds ; the alarm response time : 03 minutes 123456#65#Query the GSM module IMIE Code NO 75*1# Siren on 75*0# Siren off 52*0# Reply on 52*1# Reply off 53*1# Delay Arm on 53*0# Delay Arm off(default) Delay 10 seconds ;Not delay 40 seconds ; the alarm response time : 03 minutes NO 62 for instruction. Zone numbers ( 1-6 Wireless zone, 7 Wired zone, 8 is a button) Zone SMS Content: Chinese characters ( 8 digits ), English characters ( 32 digits ). The front 5 probes for 1-5 zone, 6-30 is the 6th zone. Whether home arm zone setting is valid. Turn on or off the siren when alarming Whether reply the SMS Complete Set or not when sending SMS to set arm/disarm by Remote Control On Set arm delay time Delay alarm time Alarm response time Return to module IMEI Code
technical parameter Basic Configuration Host Current Status Query Intercom Built-in transmission encoding settings The built-in relay control Version Number Query GSM Signal Query 123456#70*1*8888# transmission codes on 123456#70*0*8888# transmission codes off 123456#81# Relay closed 123456#80# Relay disconnected by default 123456#66# 123456#67# Ⅶ.technical parameter Host 3# 4# 5# 70*1*8888# transmission codes on 70*0*8888# ransmission codes off 81#Relay closed 80#Relay disconnected by default Monitor alarm spot Alarm Spot Intercom Relay closed when alarm, SMS, telephone can be operated Current Version Number Query Power supply: AC=110-240V ±10% DC=12V (Built-in rechargeable Ni-MH battery) Stand by current: <20mA 123456#63# NO Return to the current status of host Host Arm 123456#1# 1# Host arm operation Host disarm 123456#2# Home Arm 123456#3# Dial the phone NO to monitor when alarming NO 2# NO NO Host disarm operation Host home arm operation internal transmission on and encoding settings on Check GSM Signal: 33 levels: 0-33 The lower the number, the worse the signal. Alarm current: <400mA Wireless receiving frequency: 433MHz ± 0.5MHz GSM Signal System: 850/900/1800/1900MHz/optional 4-frequency Wireless receiver sensitivity: 5mV/m Anti-jamming intensity: 1V/m (frequency range 20-1000 MHZ) External Alarm Siren Volume: 110db Working environment: Temperature 0 ~+40 Relative humidity 90% no fog Configurable wireless devices: 8 pieces Remote Controls, 30 pieces Sensors Ⅷ.Basic Configuration 1.1 main panel 2.2 remote controls 3.1 Wireless Door Sensor 4.1 Wireless PIR Sensor 5.1 Siren 6.1 DC12V/500mA power adapter 7.1 Rechargeable backup battery 8.1 User manual (including warranty card )
The following sensors are optional: Optional sensors/detectors are packed separately. You can choose according to your specific requirrments.