INSTALLATION, OPEATION & MAINTENANCE INSTUCTIONS 1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424 E-mail: haws@hawsco.com website: www.hawsco.com Model Eye/Face Wash No. 2080063() NOTE TO INSTALLE: Please leave this information with the Maintenance Department. LIMITED WAANTY HAWS warrants that this specific product is guaranteed against defective material or poor workmanship for a period of one year from date of shipment. HAWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to Haws within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above. Buyer agrees that Haws has made no other warranties either expressed or implied in addition to those above stated, except that of title with respect to any of the products or equipment sold hereunder and that HAWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale. The emergency equipment manufactured by HAWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose for which they were intended. This product is intended to supplement first-aid treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this emergency equipment will prevent serious injury or the aggravation of existing or prior injuries. NO OTHE WAANTIES EXPESSED O IMPLIED AE AUTHOIZED, POVIDED O GIVEN BY HAWS. SHOULD YOU EXPEIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL PLEASE CALL: TECHNICAL SUPPOT: 1-800-766-5612 FO CUSTOME SEVICE: 1-888-640-4297 07/17 Model Page 1 of 5
LOCATION OF UNIT: The Model Eye/Face Wash should be installed in close proximity to potential accident areas. It should be clearly identified free from obstructions and easy to access. SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2-6 ATM) flowing line pressure. Where sediment or mineral content is a problem, an inlet filter is recommended. PLUMBING CONNECTIONS: Inlet supply is 1/2" O.D. slip joint. TOUBLESHOOTING POBLEM EPAI CHECKLIST 1. No flow. 1. Check the main shut-off valve. 2. Insufficient water flow. 2. a. Verify minimum 30 psi flowing supply line pressure. b. Probable clogging of flow control due to inadequate line flushing. Unscrew eye/face wash head and remove the four screws to disassemble head. Clean flow control and reassemble head. 3. Eye/face wash stream does not meet desired eye level. 3. a. Possible blocked flow control, see above solution. b. Possible non-leveled eye/face wash assembly. INSTALLATION INSTUCTIONS efer to installation drawing to clarify installation procedure. Note: Model Eye/Face Wash can be mounted on either right or left side of the sink. For left hand use, reconfigure as shown on installation drawing. STEP 1: STEP 2: STEP 3: STEP 4: emove the 3" O.D. flange from valve body. emove the protective backing from rubber washer. After making sure that bottom surface of the counter top or deck, around the drilled hole is clean and free of grease, slide valve through drilled hole from the bottom. Place sign over valve. STEP 5: einstall the 3" O.D. flange, ensure that the top surface of flange is flush with valve. Wrench tighten locknut against base of counter or deck. STEP 6: Install eye/face wash assembly to valve and after checking for proper alignment, tighten the setscrew on the cap. 2017 Haws Corporation All ights eserved HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 07/17 Model Page 2 of 5
THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS PATS BEAKDOWN ITEM DESCIPTION 1 E/F WASH AXION 2 VALVE ASSEMBLY 3 SWING AWAY SIGN 4 EYEWASH SIGN 5 TEST TAG EPAI KIT PAT NO. 0002953160-0005240025 SP175 SP170 VK7650 1 4 3 2 5 ECN NO. EVISED PE BY ECN: 5211 JP DAWN DATE CHKD EVISION STH /21/96 GC APPOVED DATE FV 08/09/17 SCALE: 1:1 DAWING TYPE: PATS BEAKDOWN SIZE: A SHEET 1 OF 1 WHEN ODEING PATS PLEASE SPECIFY MODEL NUMBE. C 2017 Haws Corporation - All ights eserved HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 0002080063 PAGE 3 of 5
THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS 3-5/8" 92mm 1-5/8" 41mm MAX. DECK THICKNESS SINK (EFEENCE) 6"(152mm) MIN. CLEAANCE LEFT HAND MOUNTING LOCATION LOCKNUT VALVE CAP SET SCEW " 254mm OFF CLEAANCE ADIUS SET SCEW SUPPLY SHANK 1-3/4" 45mm 3-1/4" 83mm FLANGE SIGN IGHT HAND MOUNTING LOCATION UBBE WASHE & D-NOTCH WASHE 4-7/8" 124mm 1/2" O.D. SUPPLY (BY OTHES) SUPPLY SHANK CAN BE POSITIONED IN ONE OF FOU DIECTIONS 90 APAT BY LOOSENING THE CAP SET SCEW AND OTATING VALVE NOTES: 1. 2. 3. 4. MIN. CLEAANCE TO SINK EDGE LEFT HAND APPLICATION MOVE SET SCEW INDENTATION IN SPOOL FO CAP SET SCEW THE ANSI Z358.1-2009 STANDAD SPECIFIES EYEWASH NOZZLE HEIGHTS TO BE 83.8cm (33 IN.) TO 114.3cm (45 IN.) ABOVE THE FLOO INSTALL SO THAT EYEWASH HEAD IS OVE SINK WHEN ACTIVATED. DILL ONE Ø1-3/8" [35mm] HOLE WHEE UNIT IS TO BE INSTALLED. ±1/2" [6.4mm]. THESE DIMENSIONS MAY VAY FLIP OVE Left Hand ight Hand SIGN PAGE 4 OF 5 SEAL BASE WITH SILICONE CAULK (BETWEEN BOTTOM OF SIGN AND COUNTETOP) 5" 127mm MIN. CLEAANCE ADIUS FO FACEWASH STEAMS OPPOSITE SIDE AND 15.2cm (6 IN.) MINIMUM FOM WALL O NEAEST OBSTUCTION. C 2017 ECN NO. EVISED PE BY: 2065 ECN: 5211 JP DAWN: DATE: CHK'D.: STH /96 GC APPOVED: DATE: FV 08/09/17 EVISION SCALE: 8:1 DAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 2 Haws Corporation - All ights eserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 0002080063.D
THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS SEAL BASE WITH SILICONE CAULK BE SUE TOP SUFACE OF FLANGE IS FLUSH WITH VALVE AS SHOWN BE SUE SIGN IS ON POPE SIDE BE SUE POTECTIVE BACKING IS EMOVED FOM UBBE WASHE D-NOTCH WASHE LOCKNUT C 2017 ECN NO. EVISED PE BY: ECN: 5211 JP DAWN: DATE: CHK'D.: STH /96 GC APPOVED: DATE: FV 08/09/17 EVISION SCALE: 1:1 DAWING TYPE: INSTALLATION SIZE: A SHEET 2 OF 2 Haws Corporation - All ights eserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 0002080063.D