SMD Rework Station Thank you for purchasing the Hakko 50B SMD Rework Station. The Hakko 50B is designed to solder and desolder surface mounted devices with hot air. Please read this manual before operating the Hakko 50B. Keep this manual readily accessible for reference. TABLE OF CONTENTS PACKING LIST / SPECIFICATIONS... SAFETY INSTRUCTIONS... PART NAMES... PREPARATION: ASSEMBLY AND ELECTRICAL CONNECTION... OPERATION... 5 MAINTENANCE / INSPECTION... TEMPERATURE DISTRIBUTION CHART... OPTIONAL NOZZLES... PARTS LIST / HANDPIECE... STATION... WIRING DIAGRAM...
PACKING LIST Check the contents of the Hakko 50B package and confirm that all the items listed below are included: Hakko 50B station... Power cord... Handpiece holder... FP pick-up... FP pick-up wire... Instruction manual... * This product does not include a nozzle. A large selection of nozzles is available for the Hakko 50B. Select the nozzle or nozzles suitable for the work to be performed. Hakko 50B station FP pick-up with (S) wire Handpiece FP pick-up wire (L) Handpiece holder Power cord SPECIFICATIONS Name Power consumption Station Power Consumption Pump Capacity Control temperature External dimensions Weight Hakko 50B V 0W 0V 0W 0V W 0V W 0V 0W 0V 0W Handpiece 0 W (Stand-by power consumption 0V W, 0 0V W) Diaphragm pump /min (max) 0 C ( F) (Use AB) 5(l) 0(w) (h) mm..9(l).(w) 5.(h) in. kg. (. lb.) Power consumption Total length (w/o cord) Weight (w/o cord) V 50W 0V 0W 0V 0W 0V 0W 0V 0W 0V 0W 9(l) mm /.(l) in. 0 g / 0. lb. * This product is ESD-protected. * Specifications and design subject to change without notice.
SAFETY INSTRUCTIONS WARNING Warnings and cautions are placed at critical points in this manual to direct the operator's attention to significant items. They are defined as follows: WARNING: Failure to comply with a WARNING may result in serious injury or death. CAUTION: Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved. Two examples are given below. Be sure to comply with following WARNINGS and CAUTIONS for your safety. WARNING Be sure not to operate the unit with any combination of temperature and air flow settings that makes the thermal protector trip (the heater lamp turns off during use). This could damage the unit. After use, do not disconnect the plug during the automatic cool-down process. CAUTION When the power is ON, the temperature of the hot air and the nozzle ranges from to 50 C. ( to F.). To avoid injury to personnel or damage to items in the work area, observe the following: Do not direct the hot air toward personnel or touch the metal parts near the nozzle. Do not use the product near combustible gases or flammable materials. Advise those in the work area that the unit can reach very high temperatures and should be considered potentially dangerous. Turn the power OFF when no longer using the Hakko 50B or when leaving it unattended. Before replacing parts or storing the unit, allow the unit to cool and then turn the power OFF. To prevent accidents and failures, be sure to take the following precautions: Do not strike the handpiece against hard surfaces or otherwise subject it to physical shock. This will damage the quartz glass shield around the heating element, and could damage the heater as well. Be sure the unit is grounded. Always connect power to a grounded receptacle. Do not disassemble the pump. Do not modify the unit. Use only genuine Hakko replacement parts. Do not wet the unit or use the unit with wet hands. Remove power cord by holding the plug - not the wires. Make sure the work area is well ventilated. The Hakko 50B is not intended for use by children or infirm persons without supervision. Children should be supervised to ensure that they do not play with the Hakko 50B.
PART NAMES Station Handpiece holder mounting screw POWER Handpiece holder mounting screw lamp Heater lamp HEAT CONTROL 5 AIR CONTROL 5 Power switch control knob Temperature control knob Power receptacle Handpiece holder Fuse Handpiece HOT CAUTION Nozzle (not included) Accessories FP pick-up with (S) wire (Width of wire mm (0.55in.)) FP pick-up wire (L) (Width of wire 0mm (.in.))
CAUTION PREPARATION: ASSEMBLY AND ELECTRICAL CONNECTION Preparation: Assembly and Electrical Connection A. Station Assembly Attach the handpiece holder. Remove the handpiece holder mounting screw from the side of the station. Attach the handpiece holder to the station. (Figure ) (The handpiece holder can be installed on either the left or right side.) (Figure ) B. Handpiece Assembly Attach the nozzle. Loosen the nozzle mounting screw. Attach the nozzle as shown in the drawing. (Figure ) Tighten the nozzle mounting screw. (Figure ) Inside screw (Figure ) C. Electrical Connection and Power ON When installing an optional nozzle to the Hakko 50B, do not remove this inside screw.. Connect the power cord to the power receptacle on the back panel of the station. (Figure ). Place the handpiece on the holder. (Figure 5). Plug the power cord into a grounded wall socket. After connection, the automatic blowing function will start sending air through the pipe, but the heating element remains cool.. Turn the power switch ON. NOTE: The power switch may be turned on at any time while the automatic blowing function is operating. Once the power switch is turned on, the heating element will begin to warm up. CAUTION HOT (Figure ) This product is ESD-protected. Be sure to use a grounded wall socket. Top View CAUTION When not in use, place the handpiece on the holder. (Figure 5)
HEAT CONTROL OPERATION QFP Desoldering POWER. Adjust the air flow and temperature control knobs. Refer to the temperature distribution chart (page ) to adjust the air flow and temperature control knobs. Wait for the temperature to stabilize for a short period of time. 5 AIR CONTROL 5 control knob WARNING Temperature control knob If the thermal protector is tripped (the heater lamp turns off during use), reduce the temperature setting or increase the air flow. Be sure not to operate the unit with temperature and air flow settings that makes the thermal protector trip. This could damage the unit.. Place the FP pick-up under the IC lead. Slip the FP pick-up wire under the IC lead. (Refer to the photo shown.) If the width of the IC does not match the size of the FP pick-up, adjust the width of the pick-up by squeezing the wire. In case of PLCC or small components such as chip resistors, desolder by using tweezers, etc.. Heating Hold the handpiece so that the nozzle is located directly over, but not touching the IC, and allow the hot air to melt the solder. Be careful not to touch the leads of the IC with the nozzle.. Remove the IC. Once the solder has melted, remove the IC by lifting the FP pick-up. 5. Remove any remaining solder. After removing the IC, remove remaining solder with a soldering iron and wick or desoldering tool. 5
OPERATION QFP Soldering. Apply the solder paste. Apply the proper quality of solder paste and install the SMD on the PWB.. Preheat the SMD. Refer to the photo to preheat SMD.. Soldering Heat the lead frame evenly.. Cleaning When soldering is completed, clean the residual flux from the board with an appropriate cleaner. NOTE: Soldering with hot air has many advantages, such as the inherent ability to pre-heat the component being replaced. As with any soldering process, however, there is always the possibility of forming solder balls, bridges between leads, and inadequate solder joints. Always inspect the finished solder joints for structural and electrical integrity. Turn the power switch off. After the power switch is turned off, an automatic blowing function begins sending cool air through the pipe in order to cool the handpiece. Do not disconnect the plug during this cooling process. CAUTION During the cooling process, the amount of air is controlled by the setting of the air flow adjustment knbob. Hakko recommends setting the knob at when cooling for greatest efficiency.
MAINTENANCE / INSPECTION Broken heating element A. Open the handpiece. Remove the three screws holding the handpiece together. (Figure ). Move the tube away from the handpiece, as shown.. Open the handpiece. Disconnect the grounding wire sleeve () and pipe from the protruding portion of the handle. Remove the pipe. (Figure ) Connector () CAUTION Quartz glass and heat insulation are inside the pipe. Be careful not to drop or lose these items.. Disconnect the connector () and remove the heating element. Grounding wire sleeve () B. Measure the resistance value Connect an ohmmeter across the connector terminals (a). The correct values are approximately: -0Ω (-0V), 0-Ω (0-0V). If the resistance value is incorrect, replace the part. (Refer to the instructions included with the replacement part.) (a) CAUTION Handle the heating element with care. Never rub the heating element wire! Insert the handle's projection into the hole in the pipe. Replacing the fuse. Unplug the power cord from the power receptacle.. Remove the fuse holder.. Replace the fuse. 5A (-0V),.A (0-0V). Put the fuse holder back in place.
TEMPERATURE DISTRIBUTION CHART CAUTION These charts are for reference. If the thermal protector trips, reduce the temperature setting or increase the air flow. Test criteria: Measured at a point mm (0. in.) from the nozzle by recorder. AB Single Ø.5 (0.09) C 500 AB QFP 0 0 (0.9 0.9) AB QFP (0.55 0.55) 5 5 5 AB QFP.5.5 (0. 0.) AB QFP 0 (0.55 0.) A9B QFP (..) 5 5 5 A0 Single Ø. (0.) A SOP. 0 (0. 0.9) C 500 A SOP 5. (0. 0.5) C 500 5 5 5 A SOP.5 (0. 0.59) A SOP.5 (0. 0.) AB PLCC.5.5 (0. 0.) ( Pins) 5 5 5
TEMPERATURE DISTRIBUTION CHART AB PLCC 0 0 (0. 0.) (5 Pins) C 500 AB PLCC 5 5 (0.9 0.9) ( Pins) AB PLCC 0 0 (..) ( Pins) 5 5 5 A9B PLCC.5. (0.9 0.9) ( Pins) A0B PLCC.5.5 (0.5 0.5) ( Pins) AB PLCC.5 (0.5 0.55) ( Pins) 5 5 5 AB Bent Single.5 (0.0 0.) AB BQFP (0.9 0.9) AB TSOL.5 (0. 0.) 5 5 5 AB SOP (0. 0.) AB SOP.. (0. 0.5) A9B SOP (0.5.) 5 5 5 9
A0B SOP. (0. 0.) AB QFP 0 0 (0. 0.) AB QFP (0. 0.) 5 5 5 AB QFP 0 (..5) AB QFP 0 0 (.5.5) AB QFP (..) 5 5 5 A Dual Single Ø.5 5-0 (0.0 0.-0.9) 5 0
OPTIONAL NOZZLES NOTE: The size in Name/ Specification indicates the size of IC package. QFP SOP PLCC SOJ A B 0. (0.0) Air nozzle. (0.0) mm (inch) AB Single Ø.5 (0.09) AB QFP 0 0 (0.9 0.9) AB QFP (0.55 0.55) AB QFP.5.5 (0. 0.) AB QFP 0 (0.55 0.) Ø.5 (I.D.) (0.09) 0 (0.9) A0 Single Ø. (0.) A SOP. 0 (0. 0.9) A SOP 5. (0. 0.5) A SOP.5 (0. 0.59) 0 (0.9) (0.59) (0.) 9 (.) A SOP.5 (0. 0.) Ø. (I.D.) (0.). (0.9) AB PLCC 0 0 (0. 0.) (5 Pins) 5. (0.). (0.) 9 (0.5) 0 (0.9) (0.59) 9 (0.5) (0.59) A9B QFP (..) A:0. (0.) B:0. (0.) A:. (0.) B:. (0.) (0.59) 9 (0.5) A:9. (0.) B:9. (0.) A:. (0.) B:. (0.) (0.) 9 (.) A:9. (.) B:9. (.) AB PLCC.5.5 (0. 0.) ( Pins) AB PLCC 5 5 (0.9 0.9) ( Pins) AB PLCC 0 0 (..) ( Pins) (0.59) 9 (0.5) (0.9) 9 (.). (0.) A9B PLCC.5. (0.9 0.9) ( Pins).9 (0.) A: 9 (0.5) B: (0.55).9 (0.) AB TSOL.5 (0. 0.) (0.59) A:.5 (0.) B:.5 (0.) A0B PLCC.5.5 (0.5 0.5) ( Pins) 0 (0.9) AB SOP (0. 0.) 0 (0.9) A: (0.5) B: (0.5) 9 (0.5) AB PLCC.5 (0.5 0.55) ( Pins) 0 (0.9) A: (0.) B: (0.) A: (.0) (0.59) A: (0.59) B: (0.5) AB SOP.. (0. 0.5) B: (.0) (0.9) AB Bent Single.5 (0.0 0.) 5 A9B SOP (0.5.).5 (0.0) (I.D.) (0.) (I.D.) 9 (.) A: (.) B: (.) AB BQFP (0.9 0.9) (0.) A:. (0.95) B:. (0.95) (0.) A0B SOP. (0. 0.) 0 (0.9) (0.) 9 (0.5).5 (0.) AB QFP 0 0 (0. 0.). (0.) AB QFP (0. 0.).5 (0.5). (0.) (0.) (0.). (0.) 9 (.). (0.) AB QFP 0 (..5) AB QFP 0 0 AB QFP (.5.5) (..) 9 (.) 9 (.5) (.) (0.) A Dual Single ø.5 5-0 (0.0 0.-0.9) Adjustable Pitch A:0. (0.) B:0. (0.) (0.) A:. (0.) B:. (0.) 0 (0.9) 5 (0.) 9 (.5) A:. (.09) B:9. (.5) 9 (.5) A:0. (.5) B:0. (.5) (.) A:. (.) B:. (.) The pitch between the two nozzles is adjustable. 5 (0.) 0 (0.9) ø.5 (I.D.) (0.0) Screw
PARTS LIST / HANDPIECE NOTE: Spare or repair parts do not include mounting screws, if they are not listed on the description. Screws must be ordered separately. Self tapping screw Nominal size. 0 () Self tapping screw Nominal size () 5 Item No. 5 Part No. B5 A A A A B B B55 B B B5 Part Name Handle Heating element Heating element Heating element Heating element Silicone hose Pipe assembly Cord assembly Cord stopper Protective spring Clamp Description With screws V 0V 0V 0-0V With screws (0V only) With nylon strap (0V only)
PARTS LIST / STATION NOTE: Spare or repair parts do not include mounting screws, if they are not listed on the description. Screws must be ordered separately. Truss screw (Zn black) M 5 () Item No. 5 9 0 Part No. B59 B B B B0 B B B B B B50 B B5 B55 B5 B5 B5 B5 B0 B0 B5 B9 B B B B B5 B B Part Name Cover Handpiece holder Sound-proof tank Air pump Air pump Air pump Silicone tube Fuse Fuse Power receptacle Chassis Radiation sheet P.W.B. P.W.B. P.W.B. P.W.B. Switch Air nozzle Knob Rubber foot Exhaust nozzle Tube connector Power cord, core & American plug Power cord, core, no plug Power cord, core, BS plug Power cord, core European plug Power cord, core European plug Power cord, core, BS plug Power cord, core, Australian plug Power cord, core, Chinese plug assembly Description V, with high nut, nylon tape, double-side tape 0-0V, with high nut, nylon band, double-side tape 0-0V, with high nut, nylon band, double-side tape 5 0l (mm.) 0. 0. 5.l (in.) V-5A 50V-.A V, with potentiometer, triac 0-0V, with potentiometer, triac 0-0V, with potentiometer, triac 0V, with potentiometer, triac With cord stopper With screw Set of If you need exhaust nozzle, contact your Hakko representative. With silicone tube India Korea Eur. U.K. Pan head screw with washer (w/ spring washer) M () 0 Pan head screw (Zn black) M 0 () Pan head screw with washer (w/ spring, plain washer) M 9 Pan head screw with washer (w/ spring washer) M 0 () Pan head screw with washer (w/ spring washer) M () External tooth lock washer (nominal size ) () 5 Plain washer polycarbonate (nominal size 5) () Truss screw (M ) ()
WIRING DIAGRAM Pump Heating element Power switch Power receptacle P.W.B./ Heat control Triac OVERSEAS AFFILIATES U.S.A. AMERICAN HAKKO PRODUCTS, INC. 50 ANZA DR. SANTA CLARITA, CA 95, U.S.A. TEL: () 9-0090 FAX: () 9-009 Toll Free (00)-HAKKO 5 5 http://www.hakkousa.com HONG KONG HAKKO DEVELOPMENT CO., LTD. ROOM 0, EASTERN HARBOUR CENTRE, HOI CHAK STREET, QUARRY BAY, HONG KONG. TEL: -55 FAX: 590-0 http://www.hakko.com.hk/ CHINA HAKKO DEVELOPMENT CO., LTD. ROOM -, FLOOR, INTERNATIONAL BANK TOWER 9 DONGFENG ROAD WEST, GUANGZHOU 500, CHINA. TEL: (00)-0, -0 FAX: (00)-0 TAIWAN HAKKO DEVELOPMENT CO., LTD. 5F, NO.-, HSING TE RD.,SANCHUNG, TAIPEI HSIEN, TAIWAN. TEL: (0)5-5 FAX: (0)5-5 HEAD OFFICE -5, SHIOKUSA -CHOME, NANIWA-KU, OSAKA, 55-00 JAPAN TEL:+--5-5 FAX:+--5- http://www.hakko.com SINGAPORE HAKKO PRODUCTS PTE., LTD., GENTING LINK #0-0, PERFECT INDUSTRIAL BUILDING, SINGAPORE 95 TEL: - FAX: -00 MALAYSIA HAKKO PRODUCTS SDN BHD MALAYSIA HEAD OFFICE NO.,JALAN PEMBERITA U/9,SEKSYEN U, TEMASYA INDUSTRIAL PARK,00 GLENMARIE, SHAH ALAM,SELANGOR DARUL EHSAN,WEST MALAYSIA. TEL: (0)59-5 FAX: (0)59-5 PENANG BRANCH 9,LORONG IKS JURU, TAMAN PERINDUSTRIAN RINGAN JURU, SEBERANG PERAI TENGAH, PENANG,MALAYSIA. TEL: (0)50-0 FAX: (0)50-0999 JOHORE BAHRU BRANCH 5A,JALAN SRI BAHAGIA 5,TAMAN SRI BAHAGIA, 00 JALAN TAMPOI,JOHOR BAHRU,MALAYSIA. TEL: (0)- FAX: (0)-55 PHILIPPINES HAKKO PHILS TRADING CO., INC. NO. WINDSOR TOWER CONDOMINIUM, LEGASPI ST., LEGASPI VILLAGE MAKATI, METRO MANILA, PHILIPPINES TEL: (0)-0, -99 FAX: (0)0-9 INDONESIA P.T. HAKKO PRODUCTSTAMA INDONESIA COMP BUMI INDAH BLOK IV NO. 0 NAGOYA BATAM, INDONESIA. TEL: ()5-59 FAX: ()5- P.T. HAKKO PRODUCTSTAMA INDONESIA KEBON JERUK PLAZA, BLOK D NO., JALAN RAYA PERJUANGAN, JAKARTA BARAT, JAKARTA 0, INDONESIA. TEL: ()5-0 FAX: ()5-0 Aug. 000 MA000JB0000