CHAPTER 14 MANDATORY REFERENCED STANDARDS TABLE 14-1

CHAPTER 14 MANDATORY REFERENCED STANDARDS AHAM DW-1-92 Household Electric Dishwashers Appliances AHAM DW-2PR-92 Plumbing Requirements for Household Dishwashers Appliances AHAM FWD-1-92 Food Waste Disposers Appliances AHAM FWD-2PR-89 Household Food Waste Disposer Units Appliances AHAM HLW-2 PR-86 92 Plumbing Requirements for Home Laundry Equipment Appliances ANSI A13.1-81 96 (R93) Scheme for the Identification of Piping Systems Piping ANSI A21.10-98 03 ANSI A21.11-2000 ANSI A21.51-96 02 ANSI A21.53-2000 TABLE 14-1 Standards for Materials, Equipment, and Connections Where more than one standard has been listed for the same material or method, the relevant portions of all such standards shall apply. Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1200 mm), for Water and Other Liquids (same as AWWA C110) Rubber-Gasket for Ductile-Iron Pressure Pipe and Fittings (same as AWWA C111) Ductile-Iron Pipe, Centrifugally Cast, for Water (same as AWWA C151) Ductile-Iron Compact Fittings, 3 in. through 24 in. (76 mm through 610 mm) and 54 in. through 64 in. (1400 mm through 1600 mm), for Water Service (same as AWWA C153) ANSI A40.3-93 Stainless Steel ASME B36.19-85(R94 ANSI A106.6-70 [D] Vitrified Clay Pipe (now CSA A60.1M-76[C1992]) Piping, Non-Metallic ANSI A117.1-2003 Accessible and Usable Buildings and Facilities Miscellaneous ANSI ASME A112.14.1-75 (R90) 2003 Backwater ANSI ASME A112.19.5-99 Trim for Water-Closet Bowls, Tanks, and Urinals Fixtures ANSI ASME A112.21.2M-83 Roof Drains DWV Components ANSI A118.10-93 99 Load, Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations Fixtures ANSI B2.1-90 Pipe Threads (Except Dryseal) (replaced by ASME B1.20.1-98) 241

Table 14-1 UNIFORM PLUMBING CODE ANSI ASME B16.40-85 (R94) Manually Operated Thermoplastic Gas Shutoff and in Gas Distribution Systems Fuel Gas ANSI/CSA LC 3-2000 Appliance Stands and Drain Pans Miscellaneous ANSI/ICC A117.1-98 Guidelines for Accessible and Usable Buildings and Facilities Miscellaneous ANSI Z 4.1-1995 Sanitation in Places of Employment (Table 4-1 Note 6) Miscellaneous ANSI Z21.10.1-98 01a Gas Water Heaters Volume I Storage Water Heaters CSA 4.1a02 with Input Ratings of 75,000 Btu per Hour or Less (22 kw) Appliances ANSI Z21.10.3-2001 Gas Water Heaters Volume III Storage, with Input Ratings Above 75,000 Btu per Hour, Circulating and Instantaneous Water Heaters Appliances ANSI Z21.12-90 Draft Hoods Appliances ANSI Z21.13-2000 02 Gas-Fired Low-Pressure Steam and Hot-Water Boilers Appliances CSA 4.9a02 ANSI Z21.15-97 Manually Operated Gas for Appliances, Appliance Connector,, and Hose End ANSI Z21.22-99 00 Relief and Automatic Gas Shutoff Devices for CSA 4.4-00 Hot-Water Supply Systems ANSI Z21.24-2001 Connectors for Gas Appliances Appliances ANSI Z21.41-98 Quick-Disconnect Devices for Use with Gas Fuel Appliances CSA 6.9-M98 ANSI Z21.47b-02 Gas-Fired Central Furnaces ANSI Z21.5.1a-03 Gas Clothes Dryers Type 1 Clothes Dryer ANSI Z21.5.2a-03 Gas Clothes Dryers, Type 2 Clothes Dryers ANSI Z21.56-98 01 Gas-Fired Pool Heaters Swimming Pools CSA 4.7-2001 and Spas ANSI Z21.69-97 02 Connectors for Movable Gas Appliances Appliances CSA 6.16-M97 02 ANSI Z21.70-81[D] Earthquake-Actuated Automatic Gas Shutoff Systems (withdrawn from ANSI June 1992) (replaced by ASCE 25) ANSI Z21.80-1997 03 Line Pressure Regulators Fuel Gas CSA 6.22-M97 ANSI Z21.81-1997 Cylinder Connection Devices Fuel Gas CSA 6.25-M97 ANSI Z21.86-2000 Vented Gas-Fired Space-Heating Appliances Appliances CSA 2.32-2000 ANSI Z34.1-93 Certification - Third Party Certification Programs for Products, Processes, and Services ANSI Z83.11-02 Gas Food Service Equipment ANSI Z124.1-95 Plastic Bathtub Units Fixtures ANSI Z124.2-95 Plastic Shower Units Fixtures ANSI Z124.3-95 Plastic Lavatories Fixtures ANSI Z124.4-96 Plastic Water Closet Bowls and Tanks Fixtures ANSI Z124.5-97 Plastic Toilet (Water Closet) Seats Fixtures 242

MANDATORY REFERENCED STANDARDS Table 14-1 ANSI Z124.6-97 Plastic Sinks Fixtures ANSI Z124.7-97 Prefabricated Plastic Spa Shells Fixtures ANSI Z124.8-90 Plastic Bathtub Liners Fixtures ANSI Z124.9-94 Plastic Urinal Fixtures (Note 1) Fixtures ANSI Z223.1-99 02 National Fuel Gas Code (same as NFPA 54) Fuel Gas ANSI Z358.1-98 Emergency Eyewash and Shower Equipment Miscellaneous ARI 1010-94 02 Drinking Fountains and Self-Contained, Mechanically Refrigerated Drinking Water Coolers Appliances ASCE 25-99 Earthquake Actuated Automatic Gas Shutoff Devices ASHRAE 90.1-2001 Energy Standard for Buildings Except Low-Rise Residential Buildings Miscellaneous ASME A112.1.2-96 91(R02) Air Gaps in Plumbing Systems Piping ASME A112.1.3-2000 Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances Fixtures ASME A112.3.1-93 Stainless Steel Drainage Systems for Sanitary, Storm, and Chemical Applications, Above and Below Ground (Note 1) ASME A112.3.4-2000 Macerating Toilet Systems and Related Components Fixtures ASME A112.4.1-93 (R98) Water Heater Relief Valve Drain Tubes Appliances (R02) ASME A112.4.2-03 Water Closet Personal Hygiene Devices Fixtures ASME A112.4.3-99 Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System Piping ASME A112.4.7-02 Point of Use and Branch Water Submetering Systems Miscellaneous ASME A112.6.1M-97 (R02) Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use Fixtures ASME A112.6.2-2000 01 Framing-Affixed Supports for Off-the-Floor Plumbing Fixtures Fixtures ASME A112.6.3-01 Floor and Trench Drains DWV Components ASME A112.6.7-01 Enameled and Epoxy Coated Cast Iron and PVC Plastic Sanitary Floor Sinks Fixtures ASME A112.14.3-2001 Grease Interceptors Fixtures ASME A112.14.4-2001 Grease Recovery Removal Devices Fixtures ASME A112.18.1M-2000 03 Plumbing Fixture Fittings ASME A112.18.2-02 Plumbing Fixture Waste Fittings Fittings ASME A112.18.3-96 02 Backflow Protection Devices and Systems in Plumbing Fixture Kitchen, Lavatory, and Shower Fittings with Attached Hose Outlets ASME A112.18.6-99 03 Flexible Water Connectors Piping ASME A112.18.7-99 Deck Mounted Bath/Shower Transfer with Integral Backflow Protection ASME A112.19.1M-94 Enameled Cast-Iron Plumbing Fixtures (R99) (Supplement 1-1998) Fixtures 243

Table 14-1 UNIFORM PLUMBING CODE ASME A112.19.2M-98 Vitreous China Plumbing Fixtures Fixtures ASME A112.19.3M-2000 01 Stainless Steel Plumbing Fixtures (Designed for Fixtures Residential Use) ASME A112.19.4M-94 Porcelain-Enameled Formed Steel Plumbing Fixtures (R99) (Supplement 1-1998) Fixtures ASME A112.19.5-99 Trim for Water-Closet Bowls, Tanks, and Urinals Fixtures ASME A112.19.6-95 Hydraulic Performance Requirements for Water Closets and Urinals Fixtures ASME A112.19.7M-95 Whirlpool Bathtub Appliances Fixtures ASME A112.19.8M-87 Suction Fittings for Use in Swimming Pools, Wading Swimming Pools (R96) Pools, Spas, Hot Tubs, and Whirlpool Bathtub Appliances and Spas ASME A112.19.9M-91 (R98) Non-Vitreous Ceramic Plumbing Fixtures Fixtures (R02) ASME A112.19.10-03 Dual Flush Devices for Water Closets Fixtures ASME A112.19.12-2000 Wall Mounted and Pedestal Mounted Adjustable and Pivoting Lavatory and Sink Carrier System Fixtures ASME A112.19.13-01 Electrohydraulic Water Closets ASME A112.19.14-01 Six-Liter Water Closets Equipped with a Dual Flushing Device Fixtures ASME A112.19.15-01 Bathub/WhirlpoolBathtubs with Pressure Sealed Doors Fixtures ASME A112.19.17-02 Manufactured Safety VacuumRelease System (SVRS) for Fixtures Residential and Commercial Swimming Pool, Spa, Hot Tub, and Wading Pool Suction Systems ASME A112.20.1-2004 Qualification of Installers of High Purity Systems Swimming Pools & Spas Certification ASME A112.20.2-2004 Qualification of Installers of Firestop Systems and Devices for Piping Systems Certification ASME A112.21.1M-91[D] Floor Drains (Note 1) (replaced by ASME A112.6.3) DWV Components ASME A112.21.3M-85 (R01) Hydrants for Utility and Maintenance Use (Note 1) ASME A112.26.1M-84[D] Water Hammer Arresters (cancelled) Piping ASME A112.36.2M-91 (R98) Cleanouts (Note 1) DWV Components (R02) ASME B1.20.1-83 (R92) (R01) Pipe Threads, General Purpose, Inch ASME B1.20.3-76 (R03) Dryseal Pipe Threads, Inch (R82/91/98) ASME B16.1-89 98 Cast-Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, 250, and 800 ASME B16.3-99 98 Malleable-Iron Threaded Fittings ASME B16.4-98 Gray Iron Threaded Fittings (Includes Revision Services) ASME B16.5-96 Pipe Flanges and Flanged Fittings ASME B16.12-98 Iron Threaded Drainage Fittings (Note 1) ASME B16.15-85 (R94) Cast Bronze Threaded Fittings, Classes 125 and 250 Piping, Copper Alloy 244

MANDATORY REFERENCED STANDARDS Table 14-1 ASME B16.18-84 01 Cast Copper Alloy Solder Joint Pressure Fittings (Note 1) Piping, Copper Alloy ASME B16.21-92 Nonmetallic Flat Gaskets for Pipe Flanges ASME B16.22-95 01 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings Alloy Piping, Copper Alloy ASME B16.23-92 02 Cast Copper Alloy Solder Joint Drainage Fittings DWV Alloy Piping, Copper Alloy ASME B16.24-2002 2001 Cast Copper Alloy Pipe Flanges and Flanged Fittings Alloy Piping, Copper Alloy ASME B16.26-88 Cast Copper Alloy Fittings for Flared Copper Tubes Alloy Piping, Copper Alloy ASME B16.29-2002 2001 ASME B16.32-92 [D] ASME B16.33-90 02 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings DWV Alloy (Note 1) Cast Copper Alloy Solder Joint Fittings for Solvent Drainage Systems Alloy (discontinued) Manually Operated Metallic Gas for Use in Gas Piping Systems up to 125 psig Piping, Copper Alloy Piping, Copper Alloy ASME B16.34-96 Flanged, Threaded, and Welding End ASME B16.38-85 (R94) ASME B16.39-98 Large Metallic for Gas Distribution (Manually Operated, NPS 2-1/2 to 12, 125 psig Maximum) Pipe Unions, Malleable Iron Threaded (Includes Revision Services) ASME B16.47-96 Large Diameter Steel Flanges ASME B16.50-2001 Wrought Copper and Copper Alloy Braze-Joint Pressure Fittings Piping, Copper Alloy ASME B36.10M-2000 01 Welded and Seamless Wrought Steel Pipe ASME Section IV Rules for Construction of Heating Boilers Miscellaneous ASME Section VIII Rules for Construction of Pressure Vessels Miscellaneous ASME Section IX Welding and Brazing Procedures, Welders, Brazers, and Welding and Brazing Operators Certification ASSE 1001-90 02 Pipe Applied Atmospheric-Type Vacuum Breakers Backflow Protection ASSE 1002-99 Anti-Siphon Fill (Ballcocks) for Gravity Water Closet Flush Tanks Backflow Protection ASSE 1003-2001 Water Pressure Reducing ASSE 1004-90 Backflow Prevention Requirements for Commercial Dishwashing Machines Backflow Protection ASSE 1005-99 Water Heater Drain ASSE 1006-89 86 Residential Use Dishwashers Appliances ASSE 1007-92 86 Home Laundry Equipment Appliances ASSE 1008-89 86 Household Food Waste Disposer Units Appliances ASSE 1009-90 Commercial Food Waste Grinder Units Appliances ASSE 1010-98 2004 Water Hammer Arresters Piping ASSE 1011-95 2004 Hose-Connection Vacuum Breakers Backflow Protection 245

Table 14-1 UNIFORM PLUMBING CODE ASSE 1012-2002 Backflow Prevention with Intermediate Atmospheric Vent Backflow Protection ASSE 1013-99 Reduced Pressure Principle Backflow Preventers and Reduced Backflow Protection Pressure Fire Protection Principle Backflow Preventers ASSE 1014-90 89 Hand-Held Showers Fixtures ASSE 1015-99 Double-Check Backflow Prevention Assembly Assemblies Backflow Protection and Double Check Fire Protection Backflow Prevention Assemblies ASSE 1016-96 ASSE 1017-98 03 Individual, Thermostatic Pressure Balancing and Combination Pressure Balancing and Thermostatic Control for Individual Fixtures Fittings Temperature Actuated Mixing for Hot Water Distribution Systems ASSE 1018-2001 Trap Seal Primer, Water Supply Fed ASSE 1019-97 Vacuum Breaker Wall Hydrant, Freeze-Resistant Automatic Draining Type Backflow Protection ASSE 1020-98 Pressure Vacuum Breaker Assembly Backflow Protection ASSE 1021-2001 Drains Air Gaps for Domestic Dishwasher Applications Backflow Protection ASSE 1022-03 Backflow Prevention for Beverage Dispensing Equipment Backflow Protection ASSE 1023-79 Hot Water Dispensers, Household Storage Type, Electrical Appliances ASSE 1024-98 Dual Check Valve Backflow Preventers Backflow Prevention ASSE 1025-78 Diverters for Plumbing Faucets with Hose Spray, Anti-Siphon Type, Residential Applications ASSE 1028-81[D] Automatic Flow Controllers (discontinued) ASSE 1032-80 Dual Check Valve Type Backflow Preventers for Carbonated Beverage Dispensers Post Mix Types ASSE 1034-81[D] Fixed Flow Restrictors (discontinued) Piping Backflow Protection ASSE 1035-95 02 Laboratory Faucet Backflow Preventer Backflow Protection ASSE 1037-90 Pressurized Flushing Devices (Flushometers) for Plumbing Fixtures Backflow Protection ASSE 1044-02 Trap Seal Primer Devices-Drainage Types and Electronic DWV Components Design Types ASSE 1047-99 Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies Backflow Protection ASSE 1048-99 Double Check Detector Fire Protection Backflow Backflow Protection Prevention Assemblies ASSE 1050-2002 Air Admittance for Plumbing Drainage Systems- Stack Type Devices ASSE 1051-02 Performance Requirements for Individual and Branch Type Air Admittance for Sanitary Drainage Systems ASSE 1052-94 Hose Connection Backflow Preventers Backflow Protection 246

MANDATORY REFERENCED STANDARDS Table 14-1 ASSE 1055-97 Chemical Dispensing Systems Backflow Protection ASSE 1056-2001 Spill Resistant Vacuum Breakers Backflow Protection ASSE 1057-01 Freeze Resistant Sanitary Yard Hydrants with Backflow Backflow Proctection Protection ASSE 1060-96 Outdoor Enclosures for Backflow Prevention Assemblies Backflow Proctection ASSE 1062-97 Temperature Actuated Flow Reduction (TAFR) for Individual Fixture Fittings ASSE 1066-97 Individual Pressure Balancing In-Line for Individual Fixture Fittings (Note 9) ASSE 1069 Automatic Temperature Control Mixing ASSE 1070-2004 Water Temperature Limiting Devices ASSE 1072 Floor Drain Trap Seal Protection Device ASSE Series 5000-98 2004 ASSE 6000-98 2004 Professional Qualification Standard for Backflow Prevention Assembly Testers, Repairers, and Surveyors Professional Qualification Standard for Medical Gas Systems Installers, Inspectors, and Verifiers, Maintenance Personnel and Instructors Backflow Protection Certification ASTM A 47-99 Ferritic Malleable Iron Castings ASTM A 48-03 Gray Iron Castings ASTM A 53-2001 02 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded, and Seamless ASTM A 74-98 04 Cast-Iron Soil Pipe and Fittings (Note 1) ASTM A 126-95(R01) Gray Iron Castings for, Flanges, and Pipe Fittings ASTM A 197M-2000 Cupola Malleable Iron (Metric) ASTM A 312-2001a 03 Seamless and Welded Austenitic Stainless Steel Pipes ASTM A 377-99 03 Ductile-Iron Pressure Pipe ASTM A 518-99 03 Corrosion-Resistant High-Silicon Iron Castings (Metric) ASTM A 536-84(R-99 e1 ) Ductile Iron Castings ASTM A 653M-2001a 03 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process ASTM A 733-2001 03 Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples ASTM A 861-2001a 02 High-Silicon Iron Pipe and Fittings (Note 1) ASTM A 888-98 e1 04 Hubless Cast-Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications ASTM B 29-92(R97) 03 Refined Lead ASTM B 32-96 00 Solder Metal (Note 4) ASTM B 42-98 02 e1 Seamless Copper Pipe, Standard Sizes Piping, Copper Alloy 247

Table 14-1 UNIFORM PLUMBING CODE ASTM B 43-98 e1 Seamless Red Brass Pipe, Standard Sizes Piping, Copper Alloy ASTM B 75-99 02 Seamless Copper Tube Piping, Copper Alloy ASTM B 88-99 e1 03 Seamless Copper Water Tube Piping, Copper Alloy ASTM B 135-2000 02 Seamless Brass Tube (Metric) Piping, Copper Alloy ASTM B 152-2000 Copper Sheet, Strip, Plate, and Rolled Bar Miscellaneous ASTM B 251-97 ASTM B 280-99 e1 03 General Requirements for Wrought Seamless Copper Copper-Alloy Tube Seamless Copper Tube for Air Conditioning and Refrigeration Field Service Piping, Copper Alloy Piping, Copper Alloy ASTM B 302-2000 02 Threadless Copper Pipe, Standard Sizes Piping, Copper Alloy ASTM B 306-99 02 Copper Drainage Tube (DWV) Piping, Copper Alloy ASTM B 370-98 03 Copper Sheet and Strip for Building Construction Miscellaneous ASTM B 447-2000 02 Welded Copper Tube Piping, Copper Alloy ASTM B 584-2000 Copper Alloy Sand Casting for General Applications (Note 5) Piping, Copper Alloy ASTM B 587-97 e1 (R03) Welded Brass Tube Piping, Copper Alloy ASTM B 641-93[D] Seamless and Welded Copper Distribution Tube (Type D) Piping, Copper Alloy (discontinued) ASTM B 642-88[D] Welded Copper Alloy UNS C21000 Water Tube (discontinued 1994) Piping, Copper Alloy ASTM B 687-99 Brass, Copper, and Chromium-Plated Pipe Nipples Piping, Copper Alloy ASTM B 716-93[D] Welded Copper Water Tube (discontinued 1994) Piping, Copper Alloy ASTM B 813-2000 e1 Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube ASTM B 819-2000 Seamless Copper Tube for Medical Gas Systems Piping, Copper Alloy ASTM B 828-2000 02 Making Capillary by Soldering of Copper and Copper Alloy Tube and Fittings ASTM C 14-99 03 Concrete Sewer, Storm Drain, and Culvert Pipe Piping, Non-Metallic ASTM C 296-2000 Asbestos-Cement Pressure Pipe Piping, Non-Metallic ASTM C 412-99 03 Concrete Drain Tile Piping, Non-Metallic ASTM C 425-2002 Compression for Vitrified Clay Pipe and Fittings ASTM C 428-97(R02) Asbestos-Cement Nonpressure Sewer Pipe (Notes 6 and 7) Piping, Non-Metallic ASTM C 443-2001 02 for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets ASTM C 478-97 03 Precast Reinforced Concrete Manhole Sections Miscellaneous ASTM C 564-97 04 Rubber Gaskets for Cast-Iron Soil Pipe and Fittings (Note 1) 248

MANDATORY REFERENCED STANDARDS Table 14-1 ASTM C 700-2002 Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated Piping, Non-Metallic ASTM C 1053-2000 ASTM C 1173-97 02 ASTM C 1277-97 03 ASTM C 1440-99 e1 03 ASTM C 1460-2000 04 ASTM C 1461-2000 02 ASTM C 1540-02 Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications (Note 1) Flexible Transition Couplings for Underground Piping Systems Shielded Couplings Joining Hubless Cast-Iron Soil Pipe and Fittings Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV); Sewer; Sanitary; and Storm Plumbing Systems for Above and Below Ground Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings Piping, Non-Metallic ASTM D 396-2001 02a Specification for Fuel Oil Miscellaneous ASTM D 1527-99 Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Sch. 40 and 80 ASTM D 1785-99 03 Poly(Vinyl Chloride) (PVC) Plastic Pipe, Sch. 40, 80, and 120 ASTM D 1869-95(R00) Rubber O-rings for Asbestos-Cement Pipe ASTM D 2104-2001 03 Polyethylene (PE) Plastic Pipe, Sch. 40 ASTM D 2146-82[D] ASTM D 2235-2001 ASTM D 2239-2001 03 Polypropylene Plastic Molding and Extrusion Materials (replaced by ASTM D 4101) Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings Polyethylene (PE) Plastic Pipe, (SDR-PR) Based on Controlled Inside Diameter ASTM D 2241-2000 Poly(Vinyl Chloride)(PVC) Pressure-Rated Pipe (SDR Series) ASTM D 2282-99 Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR) ASTM D 2321-2000 ASTM D 2447-2001 03 ASTM D 2464-99 ASTM D 2465-73[D] Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications Polyethylene (PE) Plastic Pipe, Sch. 40 and 80 (Based on Controlled Outside Diameter) Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Sch. 80 (Note 1) Threaded Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 80 (discontinued 1986) 249

Table 14-1 UNIFORM PLUMBING CODE ASTM D 2466-2001 02 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Sch. 40 (Note 1) ASTM D 2467-2001 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Sch, 80 (Note 1) ASTM D 2468-96a ASTM D 2469-76[D] Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings (Sch. 40) Socket-Type Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 80 (discontinued 1986) ASTM D 2513-2001a 03b Thermoplastic Gas Pressure Pipe Tubing and Fittings (Note 1) ASTM D 2517-2000 Reinforced Epoxy Resin Gas Pressure Pipe and Fittings ASTM D 2564-96a 02 Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems ASTM D 2609-2000 02 Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe (Note 1) ASTM D 2657-97 03 ASTM D 2661-2001 02 ASTM D 2665-2001 02a e1 Practice for Heating Fusion Joining of Polyolefin Pipe Fittings (Note 1) Acrylonitrile-Butadiene-Styrene (ABS) Sch.40 Plastic Drain, Waste, and Vent Pipe and Fittings (Note 1) Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings ASTM D 2672-96a (R03) for IPS PVC Pipe Using Solvent Cement ASTM D 2680-2001 Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping ASTM D 2729-96a 03 Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings (Note 1) ASTM D 2737-2001 03 Polyethylene (PE) Plastic Tubing ASTM D 2740-89 e1 [D] Poly(Vinyl Chloride) (PVC) Plastic Tubing (discontinued 1991) ASTM D 2751-96a ASTM D 2846-99 Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Note 1) Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems ASTM D 2855-96 (R02) ASTM D 2996-2001 ASTM D 3033-85[D] Making Solvent-Cemented with Poly(Vinyl Chloride) (PVC) Pipe and Fittings Filament-Wound Fiberglass (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Type PSP Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings (discontinued 1989) ASTM D 3034-2001 00 Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings ASTM D 3035-2001 03a Polyethylene(PE) Plastic Pipe (DR-PR) (Based on Controlled Outside Diameter) 250

MANDATORY REFERENCED STANDARDS Table 14-1 ASTM D 3036-73[D] Poly(Vinyl Chloride) (PVC) Plastic Line Couplings (discontinued 1986) ASTM D 3122-95 (R02) ASTM D 3138-95 02 Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings Solvent Cements for Transition, Acrylonitrile-Butadiene- Styrene (ABS) and Poly(Vinyl Chloride (PVC) Non-Pressure Piping Components ASTM D 3139-98 for Plastic Pressure Pipes Using Flexible Elastomeric Seals ASTM D 3140-90[D] Flaring Polyolefin Pipe and Tubing (discontinued) ASTM D 3212-96a (R03) ASTM D 3298-81[D] ASTM D 3311-94 02 ASTM D 3965-99 ASTM D 4068-2001 for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals Perforated Styrene-Rubber (SR) Plastic Drain Pipe (discontinued 1989) Drain, Waste, and Vent (DWV) Plastic Fittings Patterns (Note 1) Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane Fixtures ASTM D 4101-2002 03b Propylene Plastic Injection and Extrusion Materials Miscellaneous ASTM D 4551-96 (R01) ASTM D 6104-97 (R03) Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane Determining the Performance of Oil/Water Separators Subjected to Surface Run-Off Fixtures Fixtures ASTM E 84-2001 03b Surface Burning Characteristics of Building Materials Miscellaneous ASTM E 119-2000a Fire Tests of Building Construction and Materials Miscellaneous ASTM E 814-2000 02 Fire Tests of Through-Penetration Fire Stops Miscellaneous ASTM F 402-98 93 (R99) Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings ASTM F 405-98 97 Corrugated polyethylene (PE) Tubing and Fittings ASTM F 409-99a 02 ASTM F 437-99 ASTM F 438-2001 02 e1 ASTM F 439-2001 02 e1 Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings (Note 1) Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Sch. 80 Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Sch. 40 Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Sch. 80 251

Table 14-1 UNIFORM PLUMBING CODE ASTM F 441-99 02 Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Sch. 40 and 80 ASTM F 442-99 ASTM F 443-77 e1 [D] ASTM F 480-2000 02 ASTM F 493-97 ASTM F 628-2001 ASTM F 656-96a 02 Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) Bell-End Chlorinated Poly(Vinyl Chloride) (CPVC) Pipe, Schedule 40 (discontinued 1987) Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR) Schedule 40 and Schedule 80 Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings Acrylonitrile-Butadiene-Styrene (ABS) Sch. 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core, (Note 1) Primers for Use in Solvent Cement of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings ASTM F 667-97 Large Diameter Corrugated Polyethylene Tubing and Fittings ASTM F 714-2001 03 Polyethylene (PE) Plastic Pipe (SDR-PR) (Based on Outside Diameter) ASTM F 789-95a Type PS-46 and Type PS-115 Poly(Vinyl Chloride) (PVC) Plastic Gravity Flow Sewer Pipe and Fittings (Note 1) ASTM F 794-2001 03 Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter ASTM F 810-2001 Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields ASTM F 876-2001 e1 03a Crosslinked Polyethylene (PEX) Tubing ASTM F 877-2001 e1 02a Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems ASTM F 891-2000 e1 Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core ASTM F 894-98a Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe ASTM F 949-2001a 03 ASTM F 1216-98 03 ASTM F 1281-2001a 03 Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe with a Smooth Interior and Fittings Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-Al-PEX) Pressure Pipe ASTM F 1282-2001a 03 Polyethylene/Aluminum/Polyethylene (PE-Al-PE) Composite Pressure Pipe ASTM F 1335-04 Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service 252

MANDATORY REFERENCED STANDARDS Table 14-1 ASTM F 1476-01 Gasketed Mechanical Couplings for Use in Piping Applications ASTM F 1673-95 02 ASTM F 1743-96(R03) Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP) ASTM F 1807-99 03 Metal Insert Fittings with Copper Crimp Ring for SDR 9 Crosslinked Polyethylene (PEX) Tubing ASTM F 1866-98 ASTM F 1924-2001 e1 ASTM F 1948-99a ASTM F 1960-2000 e1 03 ASTM F 1961-99 ASTM F 1970-2001 ASTM F 1973-99 e1 02 ASTM F 1974-2000 e1 02 ASTM F 2080-2001 2002 Poly(Vinyl Chloride) (PVC) Drainage and DWV Fabricated Fittings, Schedule 40 Plastic Mechanical Fitting for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-Linked Polyethylene (PEX) Tubing Metal Cold Flare Compression Fittings with Disc Springs for Crosslinked Polyethylene (PEX) Tubing Special Engineered Fittings or Appurtenances for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly(Vinyl Chloride) (CPVC) Systems Factory Assembled Anodeless Riser and Transition Fitting in Polyethylene (PE) Fuel Gas Distribution Systems Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe Cold-Expansion Fittings With Metal Compression Sleeves for Cross-Linked Polyethylene (PEX) Pipe ASTM F 2098-01 Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX)Tubing to Metal Insert Fittings ASTM F2159-03 Plastic Insert Fittings Utilizing a Copper Ring for SDR 9 Cross-Linked Polyethylene (PEX) Tubing ASTM F 2165-02 Flexible pre-insulated Piping ASTM F 2262-03 Cross-LinkedPolyethylene/Aluminum/Cross-Linked Polyethylene TubingOD Controlled SDR 9 AWS A5.8-92 Filler Metals for Brazing and Braze Welding AWS B2.2-91 Brazing Procedure and Performance Qualification Certification AWWA C110-98 03 Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1200 mm), for Water and Other Liquids (same as ANSI A21.10-98) 253

Table 14-1 UNIFORM PLUMBING CODE AWWA C111-2000 AWWA C151-96 02 AWWA C153-2000 AWWA C203-91a 02 AWWA C213-2001 AWWA C215-99 AWWA C400-93 03 Rubber-Gasket for Ductile-Iron Pressure Pipe and Fittings (same as ANSI A21.11-00) Ductile-Iron Pipe, Centrifugally Cast, for Water (same as ANSI A21.51-91) Ductile-Iron Compact Fittings, 3 in. through 24 in. (76 mm through 610 mm) and 54 in. through 64 in. (1400 mm through 1600 mm), for Water Service (same as ANSI A21.53-00) Coal-Tar Protective Coatings and Linings for Steel Water Pipelines Enameled and Tape Hot Applied Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines Piping Asbestos-Cement Distribution Pipe, 4 in. through 16 in. (100 mm through 400 mm) for Water Distribution Systems Piping, Non-Metallic AWWA C500-93 02 Gate for Water and Sewerage Systems AWWA C504-2000 Rubber-Seated Butterfly AWWA C507-99 Ball, 6 in. through 48 in. (150 mm through 1200 mm) AWWA C510-97 Double Check Valve Backflow-Prevention Assembly Backflow Protection AWWA C511-97 Reduced-Pressure Principle Backflow-Prevention Assemblies Backflow Protection AWWA C606-97 Grooved- and Shouldered-Type AWWA C900-97 AWWA C901-97 02 AWWA C902-96 88 AWWA C907-91 Poly(vinyl Chloride) (PVC) Pressure Pipe, 4 in. through 12 in., for Water Distribution Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13 mm) through 3 in. (76 mm), for Water Service Polybutylene (PB) Pipe, Tubing, and Fittings, 1/2 in. Through 3 in., for Water Poly Chloride (PVC) Pressure Fittings for Water - 4in. Through 8 in. (100mm through 200mm) CISPI 301-2000 04 CISPI HSN-85[D] CISPI 310-97 04 Hubless Cast-Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications (Note 1) Neoprene Rubber Gaskets for Hub and Spigot Cast- Iron Soil Pipe and Fittings (discontinued) Couplings for Use in Connection with Hubless Cast-Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications CSA 3-92 U.S. Requirements for Excess Flow CSA A 257-03 Concrete Pipe and Manhole Sections Piping CSA B45-02 Plumbing Fixtures Fixtures 254

MANDATORY REFERENCED STANDARDS Table 14-1 CSA B45.1-02 Ceramic Plumbing Fixtures Fixtures CSA B45.2-02 Enameled Cast-Iron Plumbing Fixtures Fixtures CSA B 45.3-02 Porcelain-Enameled Steel Plumbing Fixtures Fixtures CSA B 45.4-02 Stainless Steel Plumbing Fixtures Fixtures CSA B 45.5-02 Plastic Plumbing Fixtures Fixtures CSA B 45.9-02 Macerating Systems and Related Components DWV Components CSA B45.10-01 Hydromessage Bathtubs Fixtures CSA B 64.1.1-01 Vacuum Breaker, Atmospheric Type (AVB) Backflow Protection CSA B 64.1.2-01 Vacuum Breaker, Pressure Type (PVB) Backflow Protection CSA B 64.2-01 Vacuum Breaker, Hose Connection Type (HCVB) Backflow Protection CSA B 64.2.1.1-01 Vacuum Breakers, Hose Connection Dual Check Type (HCDVB) Backflow Protection CSA B64.2.2-01 Vacuum Breakers, Hose Connection Type with Automatic Backflow Protection Drainage Feature (HCVB) CSA B 64.4-01 Backflow Preventers, Reduced Pressure Principle Type (RP) Backflow Protection CSA B 64.4.1-01 Backflow Preventers, Reduced Pressured Principle Type Backflow Protection for Fire System (RPF) CSA B64.5-01 Backflow Preventers, Double Check ValveType (DVCA) Backflow Protection CSA B64.5.1-01 Backflow Preventers, Double Check Valve Type for Fire Backflow Protection Systems (DVCAF) CSA B 64.7-01 Vacuum Preventers, Laboratory Faucet Type (LFVB) Backflow Protection CSA B 125-01 Plumbing Fittings CSA B 137.1-02 Polyethylene Pipe, Tubing, and Fittings for Cold Water Pressure Services CSA B137.5-02 Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications CSA B137.9-02 Polyethylene/Aluminum/Polyethylene Composite Pressure-Pipe Systems CSA B 137.10-02 Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Fittings Composite Pressure-Pipe Systems CSA B 181.3-02 Polyolefin Laboratory Drainage Systems CSA B 182.1-02 Plastic Drain and Sewer Pipe and Pipe Fittings CSA B 182.2-02 PVC Sewer Pipe and Fittings (PMS Type) CSA B 242-80(R98) Groove and Shoulder Type Mechanical Pipe Couplings Fittings CSA B 272-93 Prefabricated Self-Sealing Roof Vent Flashing Fittings CSA B 356-00 Water Pressure Reducing for Domestic Water Supply Systems CSA F 379.1-88 Solar Domestic Hot Water Systems (Liquid to Liquid Heat Trans CSA G401-01 Corrugated Steel Pipe Products Fittings FS A-A-51145C Flux, Soldering, Non-Electronic, Paste, and Liquid FS K65.59-71 Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings FS M265-811 Acrylonitrile-Butadiene-Styrene (ABS) Sch. 40 Plastic Drain, Waste, and Vent Pipe and Fittings FS O-F-499D-85 Flux Brazing 255

Table 14-1 UNIFORM PLUMBING CODE FS O-F-506C-72[D] Flux, Soldering (discontinued) FS OO-L-201 f-70 Shower Pans Sheet Lead, Grade B (4 lb. min.) Miscellaneous FS QQ-R-571C-69[D] Copper and Nickel Alloys (Rods) (discontinued) Miscellaneous FS TT-S-1732-71[D] Seal Compound Pipe Joint and Thread (discontinued) FS WW-P 325B-76 Lead Pipe and Bends Piping FS WW-P-541-E-90 Plumbing Fixtures, General Specification Fixtures Gen. 1980 FS WW-U-516A-74(b) Copper Alloy (Bronze) Unions Piping, Copper Alloy FS WW-V-54d[D] Valve, Gate, Bronze (125, 150, and 200 lb., Screwed Flange, Solder-End, for Land Use) (discontinued) FS WW-V-58b, Gate, Cast Iron (125 and 250 lb), Screwed and Flanged (for Land Use) IAPMO PS 1-2000a 03c Prefabricated Septic Tanks DWV Components IAPMO PS 2-2000a [D] Cast Brass and Tubing P-Traps (replaced by ASME A112.18.2) Piping, Copper Alloy IAPMO PS 4-2000e1 03a Drains for Prefabricated and Precast Showers Fixtures IAPMO PS 7-84 [D] Tubing Trap Wall Adapters (discontinued) DWV Components IAPMO PS 9-84 [D] Diversion Tees and Twin Waste Elbows (discontinued) DWV Components IAPMO PS 14-99 02 Flexible Metallic Water Connectors Piping IAPMO PS 16-2000 03a e1 Subdrains for Built-Up Shower Pans Fixtures IAPMO PS 23-89 Dishwasher Drain Air Gaps Backflow Protection IAPMO PS 25-84 03 Fittings for Joining Polyethylene Pipe for Water Service and Yard Piping IAPMO PS 31-95 Backflow Prevention Assemblies Backflow Protection IAPMO PS 33-00a Flexible PVC Hose for Pools, Hot Tubs, Spas and Jetted Bathtub IAPMO PS 34-96 03 Polyethylene Encasement Sleeve for Potable Water Pipe and Tubing Piping IAPMO PS 36-90 Lead-Free Sealing Compounds for Threaded IAPMO PS 37-90 Black Plastic PVC or PE Pressure-Sensitive Corrosion Preventive Tape Piping IAPMO PS 38-99 ABS and PVC Backwater DWV Components 256

MANDATORY REFERENCED STANDARDS Table 14-1 IAPMO PS 40-2001 Anodeless Transition Riser for Use with PVC Gas Yard Piping Fuel Gas IAPMO PS 41-99 03 Copper and Other Metallic Roof/Deck/Balcony Drains DWV Components IAPMO PS 42-96 Pipe Alignment and Secondary Support Systems Piping IAPMO PS 43-91 Cushioned Bathtubs and Whirlpool Bathtub Appliances Fixtures IAPMO PS 45-91 [D] Bathtub Three-Way Diverter with Backflow Protection (replaced by ASME A112.18.7) IAPMO PS 47-2002 e1 Plastic Roof Drains DWV Components IAPMO PS 48-2000 [D] Material Safety Data Verification for Plumbing Products Miscellaneous (replaced by NSF 61) IAPMO PS 49-92 02 Backflow Prevention Requirements for Fixture Fittings with Hose Connected Singular Moveable Outlets IAPMO PS 50-92 Dual Flush Devices For Water Closets Fixtures IAPMO PS 51-98 Plastic and Metallic Expansion Backflow Protection IAPMO PS 52-99e1 Sumps and Sewage Ejector Tanks DWV Components IAPMO PS 53-92 Grooved Mechanical Pipe Couplings and Grooved End Fittings IAPMO PS 54-2001a 03a Metallic and Plastic Utility Boxes Miscellaneous IAPMO PS 55-92 Bathwaste Strainer Drains Fixtures IAPMO PS 57-92 02 PVC Hydraulically Actuated Diaphragm Type Water Control IAPMO PS 58-92 [D] Supports for Off-the-Floor Plumbing Fixtures With or Without Concealed Tanks (replaced by ASME A112.6.2) Fixtures IAPMO PS 59-92 Septic Effluent and Waste Water Diverter DWV Components IAPMO PS 60-96 Sewage Holding Tank Containing Sewage Ejector Pump for Direct-Mounted Water Closet IAPMO PS 61-92 Fabricated Stainless Steel Security Water Closets Fixtures IAPMO PS 62-93[D] Enameled Cast-Iron Sanitary Floor Sinks (replaced Fixtures by ASME A112.6.7) DWV Components IAPMO PS 63-99a 02 Plastic Leaching Chambers DWV Components IAPMO PS 64-98 Pipe Flashings Piping IAPMO PS 65-2000 02 Air Gap Units for Water Conditioning Equipment Installation Backflow Protection IAPMO PS 66-2000 Dielectric Waterway Fittings Piping IAPMO PS 67-93 Early-Closure Replacement Flappers or Early-Closure Replacement Flapper With Mechanical Assemblies Fixtures IAPMO PS 69-2001 03a Plastic Bathwaste and Overflow Assemblies IAPMO PS 70-2001 [D] Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors Fixtures IAPMO PS 71-2000[D] 02 Electronic-Controlled Showers (superseded Fixtures by ASME A112.19.15) IAPMO PS 72-2000 03 with Atmospheric Vacuum Breakers 257

Table 14-1 UNIFORM PLUMBING CODE IAPMO PS 73-93 Dental Vacuum Pumps Miscellaneous IAPMO PS 76-95 Ballcock or Flushometer Valve Tailpiece Trap Primers and Trap Primer Receptors/Adapters DWV Components IAPMO PS 77-99[D] Electrohydraulic Water Closets (replaced Fixtures by ASME A112.19.13) IAPMO PS 78-2001 Dual Flush for Electrohydraulic and Gravity Water Closet 6 Liter (1.6 Gallon) Fixtures IAPMO PS 79-95 Multiport Electronic Trap Primer DWV Components IAPMO PS 80-95e1 03b Grease Interceptors and Clarifiers DWV Components IAPMO PS 81-2000 Precast Concrete Seepage Pit Liners and Covers DWV Components IAPMO PS 82-95 Fiberglass (Glass Fiber Reinforced Thermosetting Resin) Fittings IAPMO PS 83-95[D] Epoxy-Coated Cast-Iron Sanitary Floor Sinks (replaced Fixtures by ASME A112.6.7) IAPMO PS 84-95[D] PVC Plastic Sanitary Floor Sinks (replaced by ASME A112.6.7) Fixtures IAPMO PS 85-95 Tools for Mechanically Formed Tee Connections in Copper Tubing Piping IAPMO PS 86-95 Rainwater Diverter Valve for Non-Roofed Area Slabs DWV Components IAPMO PS 87-95 Diverter and Shutoff for Pool/Spas IAPMO PS 88-95 02 Pre-Pressurized Potable Water Tanks Miscellaneous IAPMO PS 89-95 Soaking and Hydrotherapy (Whirlpool) Bathtubs with Hydraulic Seatlift Fixtures IAPMO PS 90-95 03 Elastomeric Test Caps/Cleanout Caps DWV Components IAPMO PS 91-95 Plastic Stabilizers for Use with Plastic Closet Bends IAPMO PS 92-95 Heat Exchangers Miscellaneous IAPMO PS 93-2000 Water Closet Seats with Spray Fixtures IAPMO PS 94-2001a P-Trap, Supply Stop, and Riser Insulated Protector Miscellaneous IAPMO PS 95-2001 Drain, Waste, and Vent Hangers and Plastic Pipe Support Hooks Piping IAPMO PS 96-96 02 Passive Direct Solar Water Heaters Miscellaneous IAPMO PS 97-2001 Mechanical Cast-Iron Closet Flanges IAPMO PS 98-96 Prefabricated Fiberglass Church Baptistries Fixtures IAPMO PS 99-96 04 Terrazzo Plumbing Fixtures Fixtures IAPMO PS 100-96 Porous Filter Protector for Subdrain Weep Holes DWV Components IAPMO PS 101-97 Suction Relief IAPMO PS 102-97 Short Pattern Fixture Trap DWV Components 258

MANDATORY REFERENCED STANDARDS Table 14-1 IAPMO PS 103-97 Water Heater Stands With or Without Pans Appliances IAPMO PS 104-97 Pressure Relief Connection for Dispensing Equipment IAPMO PS 105-97 Polyethylene Distribution Boxes DWV Components IAPMO PS 106-98 Prefabricated, Tileable Shower Receptors Fixtures IAPMO PS 107-98 Aramid-Reinforced Rubber Hose for Use in Non-Potable Water Radiant Heating and Snow Melting IAPMO PS 108-98 Restaurant Fire Suppression Systems Appliances IAPMO PS 110-99 PVC Cold Water Compression Fittings Fittings IAPMO PS 111-99 PVC Cold Water Gripper Fittings Fittings IAPMO PS 112-99 PVC Plastic for Cold Water Distribution Systems Outside a Building and CPVC Plastic for Hot and Cold Water Distribution Systems IAPMO PS 113-99e1 Hydraulically Powered Household Food Waster Grinders Appliances IAPMO PS 114-99e1 IAPMO PS 115-99 02 Remote, Floor Box Industrial Water Supply, Air Supply, Drainage Demand or Automatic Activated Hot Water Pumping Systems Miscellaneous Miscellaneous IAPMO PS 116-99 Hot Water Circulating Devices Which Do Not Use a Pump Miscellaneous IAMPO PS 117-2001 04 Press Type Copper and Copper Alloy Fittings for Installation on Copper Tubing Fittings IAPMO PS 118-2000 FOG (Fats, Oils, Greases) Disposal Systems DWV Components IAMPO PS 119-2000 Water Energized Sump Pump Miscellaneous IAS 1-91 U.S. Requirements for Indirect Water Heaters for Use with External Heat Source IAS LC 1-99 Fuel Gas Piping Systems Using Corrugated Stainless Steel CSA 6.26-M99 Tubing (CSST) Fuel Gas Fuel Gas ISO Guide 65-1996 LADWP General Requirements for Bodies Operating Product Certification Systems Ultra Low Flush Toilets - Requirements Certification MIL-F-1183 H-83[D] Fittings, Pipe, Cast Bronze, Silver-Brazing (discontinued) Piping, Copper Alloy MIL-F-18180C1 Flanges and Flanged Fittings, Pipe, Steel (150, 300, 400, 600, 900, 1500, and 2500 pounds) MIL-P-17552F Pumps, Centrifugal, Water, Horizontal, General Service; and Pumps, Centrifugal Water, Horizontal, Boiler-Feed; Electric Motor or Steam Driven Pumps MIL-P-21251E Pumping Units, Sewage, Duplex, Automatic, Wet Pit Type Pumps (Superseded by FS A-A-50555) MIL-P-22561-82[D] Glass (standard cancelled per Department of Defense) Miscellaneous MIL-P-52407 Pump, Centrifugal: Electric-Motor-Driven, Shallow (A)-1976[D] Well (for Water) (discontinued) Pumps 259

Table 14-1 UNIFORM PLUMBING CODE MIL-P-62156 Submersible, Axial Flow, Electric-Motor- (1)-1983[D] Driven (discontinued) Pumps MIL-P-B-81[D] Sewage Pumps (discontinued) Pumps SSPMA-85 MIL-V-29193-80[D] Pressurized Flushing Devices (discontinued) Fixtures MSS SP-25-98 Standard Marking System for, Fittings, Flanges, and Unions Piping MSS SP-42-99 Class 150 Corrosion-Resistant Gate-Globe, Angle, and Check with Flanged and Butt Weld Ends MSS SP-44-96 Steel Pipeline Flanges MSS SP-58-93 02 Pipe Hangers and Supports Materials, Design, and Manufacture Piping MSS SP-67-95 02 Butterfly MSS SP-69-02 Pipe Hangars and Supports - Selection and Application Piping MSS SP-70-98 Cast-Iron Gate, Flanged and Threaded Ends MSS SP-71-97 Cast-Iron Swing Check, Flanged and Threaded Ends MSS SP-72-99 MSS SP-73-91 03 Ball with Flanged or Butt-Welding Ends for General Service Brazing for Wrought and Cast Copper Alloy Solder Joint Pressure Fittings MSS SP-78-98 Cast-Iron Plug, Flanged and Threaded Ends MSS SP-80-97 03 Bronze Gate-Globe, Angle, and Check MSS SP-83-2001 Class 300 Steel Pipe Unions Socket-Welding and Threaded MSS SP-84 [D] MSS SP-89-98 MSS SP-104-03 MSS SP-106-03 MSS SP-109-97 MSS SP-123-1998 NFPA 13R-99 02 Steel Socket-Welding Ends and Threaded Ends (discontinued) Pipe Hangars and Supports - Fabrication and Installation Practices Wrought Copper Solder Joint Pressure Fittings Cast Copper Alloy Flanges and Flanged Fittings, C.ass125, 150, and 300. Welded Fabricated Copper Solder Joint Pressure Fittings Non-Ferrous Threaded and Solder-Joint unions for use with copper water tube Installation of Sprinkler Systems in Residential Occupancies up to and Including Four Stories in Height Piping, Copper Alloy Miscellaneous NFPA 13D-99 02 Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes Miscellaneous NFPA 31-2001 2006 Installation of Oil-Burning Equipment Miscellaneous NFPA 54-2002 2005 National Fuel Gas Code (same as ANSI Z223.1) Fuel Gas NFPA 58-2001 2004 Storage and Handling of Liquefied Petroleum Gases Fuel Gas NFPA 85-2001 2004 Boiler and Combustion Systems Hazards Code Appliances NFPA 99-2002 Health Care Facilities Piping 260

MANDATORY REFERENCED STANDARDS Table 14-1 NFPA 99C-2002 2005 Gas and Vacuum Systems Piping NFPA 211-2000 03 Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances Miscellaneous NSF 3-2001 03 Commercial Spray-Type Dishwashing and Glasswashing Machines Appliances NSF 12-93 03e Automatic Ice Making Equipment Appliances NSF 14-2002 03 Plastic Piping Components and Related Materials NSF 18-96a Manual Food and Beverage Dispensing Equipment Appliances NSF 24-96 88 Plumbing System Components for Manufactured Homes and Recreational Vehicles Miscellaneous NSF 29-93 02 Chemical Feeders for Commercial Dishwashers Appliances NSF 40-2000 Residential Wastewater Treatment Systems DWV Components NSF 41-99 Non-Liquid Saturated Treatment Systems DWV Components NSF 42-2002e Drinking Water Treatment Units Aesthetic Effects Appliances NSF 44-2002 Addendum 1.0-02 Residential Cation Exchange Water Softeners Appliances NSF 46-2000 02 Evaluation of Components and Devices Used in Wastewater Treatment Systems DWV Components NSF 53-2002 Drinking Water Treatment Units Health Effects Appliances NSF 58-2002 Addendum 2.0-02 Reverse-Osmosis Drinking Water Treatment Systems Appliances NSF 61-2001 03e Drinking Water System Components Health Effects Miscellaneous NSF 62-99 Addendum 1.0-02 Water Distillation Systems Appliances NSPI 1-1991 03 Public Swimming Pools Swimming Pools and Spas OG 100-95 Operating Guidelines for Certifying Solar Collectors OG 300-01 Operating Guidelines and Minimum Standards for Certifying Solar Water Systems PDI G-101-85 98 Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data DWV Components PDI-WH 201-92 Water Hammer Arresters Piping SAE J 512-97 Automotive Tube Fittings Fittings SAE J1670-93 Type F Clamps for Plumbing Applications SAMA LF6a Medical Care Facility Brassware Miscellaneous UL 80-96 Steel Inside Tanks for Oil-Burner Fuel Miscellaneous UL 103-95 01 UL 125-97 Factory-Built Chimneys for Residential Type and Building Heating Appliances for Anhydrous Ammonia and LPG (Other than Safety Relief) Miscellaneous UL 132-97 Safety Relief for Anhydrous Ammonia and LPG UL 144-99 LPG Regulators UL 174-96 Household Electric Storage Tank Water Heaters Appliances UL 197-03 Commercial Electric Cooking Appliances 261

Table 14-1 UNIFORM PLUMBING CODE UL 252-03 Compressed Gas Regulations UL 296-03 Oil Burners Appliances UL 343-97 Pumps for Oil-Burning Appliances Pumps UL 352-97 Constant-Level Oil UL 378-93 Draft Equipment Miscellaneous UL 399-93 Drinking-Water Coolers Appliances UL 430-94 Waste Disposers Appliances UL 441-96 Gas Vents Miscellaneous UL 443-95 Steel Auxiliary Tanks for Oil-Burner Fuel Miscellaneous UL 499-97 Electrical Heating Appliances Appliances UL 563-95 Ice Makers Appliances UL 569-95 Pigtails and Flexible Hose Connectors for LP-Gas Fuel Gas UL 723-96 03 Standard Test for Surface Burning Characteristics of Building Materials Miscellaneous UL 726-95 Oil-Fired Boiler Assemblies Appliances UL 732-95 Oil-Fired Storage Tank Water Heaters Appliances UL 749-97 Household Dishwashers Appliances UL 778-96 02 Motor-Operated Water Pumps Pumps UL 834-95 Heating, Water Supply, and Power Boilers Electric Appliances UL 921-96 Commercial Electric Dishwashers Appliances UL 959-01 Factory Built, Medium Heat Appliance Chimneys Miscellaneous UL 1206-03 Electric Commercial Clothes Washing Equipment Appliances UL 1453-95 WQA S-300-91 Electric Booster and Commercial Storage Tank Water Heaters Point-of-Use Low Pressure Reverse Osmosis Drinking Water Systems Appliances Appliances 3-GP-28 Fuel Oil, Canadian Government Specification Board Miscellaneous Notes: 1 Although this standard is referenced in Table 14-1, some of the pipe, tubing, fittings, valves, or fixtures included in the standard are not acceptable for use under the provisions of the Uniform Plumbing Code. 4 See Section 316.1.3 for restriction. 5 Alloy C85200 for cleanout plugs. 6 Limited to domestic sewage. 7 Type II only. 9 ASSE 1066 is not intended to limit the maximum outlet temperature at point of use. 10 See Section 315.0 for trenching, excavation, and backfilling requirements when installing building drains and sewers. Engineers may wish to consult ASTM D 2321 when preparing plans and specifications for sewer mains or specific projects. 262

MANDATORY REFERENCED STANDARDS Table 14-1 Index TABLE 14-1 INDEX Standards for Materials, Equipment,, and Connections Page numbers will be added before publishing Standard Number page Appliances AHAM DW-1-92... AHAM DW-2PR-92... AHAM FWD-1-92... AHAM FWD-2-PR-89... AHAM HLW-2 PR-86 92... ANSI Z21.10.1-98 01a... ANSI Z21.10.3-2001... ANSI Z21.12-90... ANSI Z21.13-2000 02... ANSI Z21.24-2001... ANSI Z21.69-97 02 CSA 6.16-M9702... ANSI Z21.86-2000 CSA 2.32-2000... ARI 1010-94 02... ASME A112.4.1-93(R98) (R02)... ASSE 1006-89 86... ASSE 1007-92 86... ASSE 1008-89 86... ASSE 1009-90... ASSE 1023-79... IAPMO PS 103-97... IAPMO PS 108-98... IAPMO PS 113-99 e1... NFPA 85-2001 2004... NSF 3-2001 03... NSF 12-93 03e... NSF 18-96a... NSF 29-93 02... NSF 42-2002 Addendum 1.0-02... NSF 44-2002... NSF 53-2002... NSF 58-2002 Addendum 2.0-02... NSF 62-99 Addendum 1.0-02... UL 174-96... UL 296-03... UL 399-93... UL 430-94... UL 499-97... UL 563-95... UL 726-95... UL 732-95... UL 749-97... UL 834-95... UL 921-96... UL 1206-03... UL 1453-95... WQA S-300-91... Backflow Protection ASSE 1001-90 02... ASSE 1002-99... ASSE 1004-90... ASSE 1011-95 2004... ASSE 1012-2002... ASSE 1013-99... ASSE 1015-99... ASSE 1019-97... ASSE 1020-98... ASSE 1021-2001... ASSE 1022-03... ASSE 1024-98... ASSE 1032-80... ASSE 1035-95 02... ASSE 1037-90... ASSE 1047-99... ASSE 1048-99... ASSE 1052-94... ASSE 1055-97... ASSE 1056-200... ASSE 1057-2001... ASSE 1060-1996... ASSE Series 5000-98 2004... AWWA C510-97... AWWA C511-97... CSA B64.1.1-01... CSA B 64.1.2-01... CSA B64.2-01... CSA B 64.2.1.1-01... CSA B 64.2.2-01... CSA B 64.4-01... CSA B 64.4.1-01... CSA B 64.5-01... CSA B 64.5.1-01... CSA B 64.7-01... CSA B 125-01... 263