Models 840/841/842 PACKAGED TERMINAL AIR CONDITIONER AND HEAT PUMP UNITS

PACKAGED TERMINAL AIR CONDITIONER AND HEAT PUMP UNITS Models 840/841/842 Sizes 07-15 Cooling: 6,900-14,500 Btuh Heating: Heat Pump 6,000-13,400 Btuh Electric 6,400-17,000 Btuh 840/841/842 Unit Single-Package, Thru-the-Wall Units That Offer Easy Installation and Years of Dependable Performance quiet operation fixed wall sleeve, slide-out chassis attractive and durable finish chassis fits most competitive sleeves FEATURES/BENEFITS Single-package units for heating and cooling rooms in hotels, motels, offices, apartments, condominiums and residential additions. PERFORMANCE SATISFACTION The 84 Series Bryant packaged terminal air conditioner units offer a cooling and heating capacity range to satisfy virtually every application need. They are aerodynamically designed to provide quiet operation indoors and outdoors. Both occupants and neighbors are protected against any noise intrusion. Because they are built for efficient heating and cooling, multi-room building owners rely on the 84 Series unit for long-term savings in operating costs. The units require no bulky duct system, no separate equipment room, no water towers or additional cooling equipment, and no complex matchup of different system components. In addition, the units have less operating sensitivity to building orientation from such factors as sun, wind or shade. LOWER OPERATING COSTS The 84 Series heat pump models offer substantial operating savings over conventional electric resistance heaters. As electric heating energy costs have risen, heat pumps have continued to provide the user with an abundant supply of nature s own heat absorbed from the atmosphere. In cooling, the units offer exceptional EERs (Energy Efficiency Ratios) that exceed ASHRAE (American Society of Heating, Refrigeration and Air Conditioning Engineers) requirements. Each unit operates individually of other units in the building. Each tenant can choose the degree of comfort and operating economy desired. Another time and money saver is the slide-out chassis that permits units to be rapidly serviced, reducing downtime, and enabling a chassis to be replaced in minutes without disrupting other building occupants comfort. INITIAL INSTALLATION SAVINGS Installation consists of only 2 components. This minimizes handling time and possible installation problems. A weather-protected wall sleeve can be installed during building construction, with the main chassis and rear grille installed after building completion. No seasonal changeover is needed for cooling or heating periods. The units are completely self-contained comfort systems. INCREASED COMFORT The heat pump models have a 2-stage thermostat for quick temperature recovery while in the heat pump mode. This causes the heat pump to switch automatically from heat pump to electric heat when more heat is needed, then back to heat pump when heating requirement is satisfied. All models utilize a Bryant SureTemp thermostat to control room temperature closer to the desired comfort level. FACTORY OPTIONS The Bryant PTAC (packaged terminal air conditioner) unit can be ordered directly from the factory with low voltage controls for wall thermostat operation. When a thermostat is wired to the PTAC unit, the unit will operate according to the commands received from the wall thermostat. The thermostat must be ordered separately. The Bryant PTAC unit can also be ordered with the Corrosion Protection option directly from the factory. Corrosion Protection is required when the PTAC unit is installed in a coastal or corrosive environment. Form No. PDS 84.07.1

MODEL NUMBER NOMENCLATURE 84 0 D 12 3 CP Series Designation PTAC (Packaged Terminal Air Conditioner) Model 0 Cooling with Electric Heat 1 Heat Pump 2 Cooling Only Chassis Options Blank Standard CP Corrosion Protection RC Wall Thermostat Control (Not available on cooling only units) RP Wall Thermostat Control with Corrosion Protection (Not available on cooling only units) Voltage Code N 208/230-1-60 D 265-1-60 Cooling Capacity (nominal) 07 7,000 Btuh 09 9,000 Btuh 12 12,000 Btuh 15 15,000 Btuh Electric Heater Size (kw) 0 No Heaters (Cooling Only) 2 2.3 kw 3 3.4 kw 5 5.0 kw TABLE OF CONTENTS Page Features/Benefits.......................................... 1 Model Number Nomenclature................................. 2 Accessories............................................ 3-10 Base Unit Dimensions...................................... 11 Accessory Dimensions.................................. 12-14 Typical Wall Installation.................................. 15,16 Performance and Electrical Data.......................... 17,18 Typical Wiring Diagrams................................. 19-25 Guide Specifications.................................... 26,27 2

*Custom colors are also available. ACCESSORIES ACCESSORY PART NUMBER DESCRIPTION 42-SLEEVE-1PK Non-Insulated Plastic Wall Sleeve, 1 per pack 42-INSUL-1PK Insulated Plastic Wall Sleeve, 1 per pack 42-STEEL-1PK Insulated Metal Wall Sleeve, 1 per pack Wall Sleeves 42-EXT24-1PK Extended Metal Wall Sleeve for Deep Wall Applications (24-in. deep), 1 per pack 42-EXT26-1PK Extended Metal Wall Sleeve for Deep Wall Applications (26-in. deep), 1 per pack 42-EXT28-1PK Extended Metal Wall Sleeve for Deep Wall Applications (28-in. deep), 1 per pack FR-SLEEVE-EXT Friedrich wall sleeve extension to retrofit PTAC unit into Friedrich 11 1 / 2-in. deep (T Series) wall sleeve. 1 per pack GRILLE-ALU-STAMP Stamped Aluminum Exterior Grille, Clear Finish GRILLE-PLA-BROWN Plastic Architectural Rear Grille, Brown GRILLE-PLA-BEIGE Plastic Architectural Rear Grille, Beige GRILLE-ALU-CLEAR Aluminum Architectural Exterior Grille, Clear Finish GRILLE-ALU-WHITE Aluminum Architectural Exterior Grille, White GRILLE-ALU-BRONZ Aluminum Architectural Exterior Grille, Light Bronze GRILLE-ALU-MBRNZ Aluminum Architectural Exterior Grille, Medium Bronze Exterior Grilles* GRILLE-ALU-BROWN GRILLE-ALU-BEIGE Aluminum Architectural Exterior Grille, Brown (Dark Bronze) Aluminum Architectural Exterior Grille, Beige GRILLE-ALU-ALPIN Aluminum Architectural Exterior Grille, Alpine GRILLE-ALU-PEACH Aluminum Architectural Exterior Grille, Peach GRILLE-ALU-MELON Aluminum Architectural Exterior Grille, Melon GRILLE-ALU-LGREY Aluminum Architectural Exterior Grille, Light Grey GRILLE-ALU-SGREY Aluminum Architectural Exterior Grille, Slate Gray GRILLE-ALU-RDBRK Aluminum Architectural Exterior Grille, Red Brick GRILLE-ALU-BLUE Aluminum Architectural Exterior Grille, Blue GRILLE-ALU-GREEN Aluminum Architectural Exterior Grille, Green SUBBASE-NON-ELEC Non-electrical Subbase SUBBASE-230V-15A Electrical subbase with factory-installed 208/230 V, 15 amp receptacle SUBBASE-230V-20A Electrical subbase with factory-installed 208/230 V, 20 amp receptacle Subbase SUBBASE-230V-30A SUBBASE-265V-15A Electrical subbase with factory-installed 208/230 V, 30 amp receptacle Electrical subbase with factory-installed 265 V, 15 amp receptacle SUBBASE-265V-20A Electrical subbase with factory-installed 265 V, 20 amp receptacle SUBBASE-265V-30A Electrical subbase with factory-installed 265 V, 30 amp receptacle SUBBASE-HARDWIRE Electrical subbase with factory-installed hardwire kit (230/208 V and 265 V) SUBBASE-SWITCH Field-Installable Switch kit for an electrical subbase Subbase SUBBASE-FUSE-15A Field-Installed Fuse Kit (15 amp) for electrical subbase Field-Installed Kits SUBBASE-FUSE-20A Field-Installed Fuse Kit (20 amp) for electrical subbase SUBBASE-FUSE-30A Field-Installed Fuse Kit (30 amp) for electrical subbase Permanent power connection to the unit (includes 36 in. of flexible conduit and Molex connector for easy HARDWIRE-KIT-1PK Electrical Connections connect/disconnect, 230/208 V and 265 V). 1 per pack CONDUIT-INTF-4PK Interface kit for field-supplied conduit includes Molex connector for easy connect/disconnect. 4 per pack Condensate Drain Kit DRAIN-KIT-4PK Attaches to wall sleeve for controlled internal or external disposal of condensate. 4 per pack TSTATBBBAC01-B Builder's Model Electronic Thermostat w/digital display (Heat/Cool Models) Wall Thermostats TSTATBBBHP01-B Builder's Model Electronic Thermostat w/digital display (Heat Pump Models) TSTATBBPAC01-B 7-Day Programmable Electronic Thermostat (Heat/Cool Models) TSTATBBPHP01-B 7-Day Programmable Electronic Thermostat (Heat Pump Models) RC-FIELDKIT230HC Field-installed wall thermostat retrofit kit to convert a standard 230 V Heat/Cool unit to an RC unit. Wall thermostat sold separately (can be used to convert a cool only unit to RC). RC-FIELDKIT230HP Field-installed wall thermostat retrofit kit to convert a standard 230 V Heat Pump unit to an RC unit. Wall thermostat sold separately. RC-FIELDKIT265HC Field-installed wall thermostat retrofit kit to convert a standard 265 V Heat/Cool unit to an RC unit. Wall thermostat sold separately (can be used to convert a cool only unit to RC). Wall Thermostat Field-installed wall thermostat retrofit kit to convert a standard 265 V Heat Pump unit to a Interface Retrofit Kit RC-FIELDKIT265HP RC unit. Wall thermostat sold separately. Clear plastic locking thermostat cover prevents unauthorized access to thermostat. Cover for use with TSTAT-COVER-6X7 non-programmable and electro-mechanical thermostats. Outside dimensions: 6 1 / 2 in. x 7 1 / 2 in. x 21 5 / 16 inch. 1 per pack. Clear plastic locking thermostat cover prevents unauthorized access to thermostat. Cover for use with TSTAT-COVER-7X10 programmable thermostats. Outside dimensions: 7 1 / 4 in. x 9 3 / 4 in. x 3 3 / 8 inch. 1 per pack Replacement Filters 84-FILTER-10PK Replacement air filters in package of 10 Energy Management EM-KIT Allows unit to be turned on and off from a remote location (includes freeze guard protection) Locking Security Control Door 84-SECURITY-DOOR Key-locking security door to prevent access to heating and cooling controls Lateral Duct Kit 84-LATERAL-DUCT Ductwork to allow one unit to heat and cool two rooms (plenum plus extension duct and registers) Air/Curtain Deflector DEFLECTOR-1PK Lateral air deflector, with individually adjustable louvers, to enhance air circulation. 1 per pack 84-CURTDFL-1PK Curtain deflector prevents curtains from blowing into discharge airstream. 1 per pack 3

ACCESSORIES (cont) WALL SLEEVES It is recommended that a Bryant sleeve be used with a Bryant chassis. When installing any Bryant wall sleeve, note the following: If more than 4 in. of sleeve projects into the room or the wall is less than 2 in. thick, an accessory subbase must be used for support. For all applications with an accessory subbase, wall sleeve must extend 3 1 / 4 in. minimum into room and must be 3 1 / 4 in. minimum to 5 1 / 2 in. maximum above floor (including carpeting). All Bryant sleeves are self pitching and must be mounted level in all directions. (Do not use rails to level sleeve.) The sleeve should be caulked on all sides, including both inside and outside the building. Weather Last Wall Sleeve Part No.: 42-SLEEVE-1PK The accessory wall sleeve is made from a molded polymer that is designed for strength and durability. This material has excellent corrosion resistance and a flammability rating of UL94-5V. The polymer sleeve absorbs sound, provides better insulation than a metal sleeve, and offers years of protection against the elements. The rib configuration on the sleeve bottom allows easy chassis removal and aids in drainage. The sleeves are built with a pitch of 1 / 4 in. per foot. Wall sleeves must be installed level. Overflow slots are in place to divert excess water during severe weather. The sleeve surface is textured to prevent shine and hide scratches. Insulated Polymer Wall Sleeve Part No.: 42-INSUL-1PK Insulated polymer wall sleeves combine all of the above features with the addition of factory-installed insulation. The insulation helps to reduce heat loss, save energy and provides better sound absorption over the non-insulated sleeve. Insulated Metal Wall Sleeves Part No.: 42-STEEL-1PK Part No.: 42-EXT24-1PK Part No.: 42-EXT26-1PK Part No.: 42-EXT28-1PK Bryant s new metal wall sleeves are available in a variety of sizes for most applications and difficult installations. All metal wall sleeves come with factory-installed insulation, designed to minimize heat loss and reduce outdoor noise transmissions into the room. In addition, the metal wall sleeve provides a flammability rating higher than UL94-5V. 42 16 14 7/8 /24 /26 /28 METAL INSULATED WALL SLEEVE Friedrich Retrofit Wall Sleeve Adapter Part No.: FR-SLEEVE-EXT The Friedrich wall sleeve adapter is constructed of sheet metal and is designed to increase the depth of an existing Friedrich wall sleeve to accommodate Bryant s industry standard PTAC units. POLYMER WALL SLEEVE FRIEDRICH WALL SLEEVE ADAPTER KIT 4

ACCESSORIES (cont) OUTDOOR GRILLES Bryant recommends only the use of Bryant-supplied grilles for use on these units. However, the architectural designs of a building may dictate the use of special or oversized grilles and/ or louvers. Special louvers or any special architectural treatment of the building façade that may restrict free circulation of condenser airflow should be referred to your Bryant dealer for evaluation and approval. Aluminum Architectural Outdoor Grilles (Louvered) Part No.: GRILLE-ALU-CLEAR (anodized aluminum) Part No.: GRILLE-ALU-WHITE Part No.: GRILLE-ALU-BEIGE Part No.: GRILLE-ALU-ALPIN Part No.: GRILLE-ALU-BRONZ Part No.: GRILLE-ALU-MBRNZ Part No.: GRILLE-ALU-BROWN Part No.: GRILLE-ALU-LGREY Part No.: GRILLE-ALU-SGREY Part No.: GRILLE-ALU-PEACH Part No.: GRILLE-ALU-MELON Part No.: GRILLE-ALU-RDBRK Part No.: GRILLE-ALU-BLUE Part No.: GRILLE-ALU-GREEN This premium line of decorative outdoor grilles will enhance the appearance of any building. The grilles are made of strong, durable, extruded, anodized aluminum and are designed to be mounted easily from inside the room. These elegant grilles have baked enamel finishes available in several colors. For more information on custom colors and sizes, contact Reliable Products at 1-800-239-4621. Polymeric Architectural Outdoor Grilles (Louvered) Part No.: GRILLE-PLA-BROWN Part No.: GRILLE-PLA-BEIGE This value line of polymeric architectural outdoor grilles will blend attractively with most building exteriors. Mounted easily from inside the room, the one-piece, molded grille is designed for protection, enhanced appearance, and superior weatherresistance. The grille is made of durable polymer and has a colorfast, lightly-textured finish that blends well with most exterior finishes. ARCHITECTURAL GRILLE IN ALUMINUM OR POLYMERIC Standard Outdoor Aluminum Grille Part No.: GRILLE-ALU-STAMP This cost-effective, one-piece standard grille is made from durable anodized aluminum. The grille is lightweight, has a clear finish, and is easy to install from inside the room. STANDARD GRILLE 5

ACCESSORIES (cont) Outdoor Grille Selection IMPORTANT: If you wish to use a grille not made by Bryant for your Bryant unit(s), contact the PTAC Application Engineering Group at 1-877-875-3362. The following guidelines must be followed in the initial selection of any alternate exterior grille or louver: 1. The louver must have a minimum of 65% free area. Free area is the minimum area of the opening in an air inlet or outlet in which air can pass. Free Area (%) = X/Y. 2. The louver should be attached to the wall sleeve in a manner that will prevent recirculation of condenser discharge air into the inlet. In most applications, baffles, splitters, and/ or gasket will be required between the chassis tube end sheets and the louver to prevent air recirculation. The above criteria must be followed, since a louver that is restrictive or allows recirculation will result in a reduction of the unit s capacity and efficiency and will ultimately shorten the compressor life. Y X Y X LOUVER DIMENSIONAL REFERENCE Y X Y X Sample Calculations Free Area (%) = x x 100 y x = 1 y = 1.5 F.A. (%) = 1 x 100 = 66.7% 1.5 Hardwire Kit Part No.: HARDWIRE-KIT-1PK This accessory hardwire kit provides a permanent connection to the unit. Electrical hard wiring is required when NEC (National Electrical Code) or local codes restrict the use of power cord and plug connections. The hardwire kit mounts on the front right side of the unit and comes with 36 inches of flexible steel conduit and a Molex connector for easy connect/ disconnect. HARDWIRE KIT Conduit Interface Kit Part No.: CONDUIT-INTF-4PK The conduit interface accessory kit provides the wire connection to the unit to interface to field-supplied conduit. CONDUIT INTERFACE KIT 6

ACCESSORIES (cont) SUBBASE Part No.: SUBBASE-NON-ELEC Part No.: SUBBASE-230V-30A Part No.: SUBBASE-265V-30A Part No.: SUBBASE-230V-15A Part No.: SUBBASE-265V-15A Part No.: SUBBASE-HARDWIRE Part No.: SUBBASE-230V-20A Part No.: SUBBASE-265V-20A This decorative subbase supports the unit and is available in three basic models: non-electrical, electrical, and hardwired. A subbase is required for installations where the wall sleeve extends 4 or more inches into the room or the wall is less than 2 in. thick. The minimum clearance between the bottom of the sleeve and the floor is 3 1 / 4 in., and the maximum clearance is 5 1 / 2 inches. IMPORTANT: All standard cord-connected 265 V PTAC units will require a field-installed electrical subbase accessory per UL and NEC electrical codes. All subbase models are pre-assembled, mount to the wall sleeve, and come with adjustable legs and side skirting to provide a finished appearance. NON-ELECTRICAL SUBBASE ASSEMBLY Non-Electrical Subbase The easy to install, non-electrical subbase provides mechanical support and requires no wiring. Electrical Subbase The electrical subbase has a factory-installed electrical junction box containing a receptacle for corded packaged terminal air conditioner (PTAC) units. The electrical subbase series offers models from 230V-15 amp up to 265V-30 amp. Knockouts are provided for power source connections. Hardwired Subbase The hardwired electrical subbase has a factory-installed junction box containing 19 in. of flexible conduit (for a perfect fit to the PTAC unit) and all mating connections for easy assembly to PTAC units. Knockouts are provided for power source connections. ELECTRICAL SUBBASE ASSEMBLY HARDWIRED SUBBASE ASSEMBLY Subbase Fuse Kit Part No.: SUBBASE-FUSE-15A Part No.: SUBBASE-FUSE-20A Part No.: SUBBASE-FUSE-30A The fuse kit provides in-line overcurrent protection at the unit when required by NEC (National Electric Code) or local codes. IMPORTANT: The Fuse Kit can only be used with the electrical or hardwired subbase. SUBBASE FUSE KIT Subbase Power Disconnect Switch Part No.: SUBBASE-SWITCH The subbase power disconnect switch provides a recessed power disconnect for the PTAC unit when required by NEC or local codes. IMPORTANT: This accessory can only be used with the electrical or hardwired subbase. ON POWER DISCONNECT SWITCH ASSEMBLY 7

CLEAN FILTER ACCESSORIES (cont) THERMOSTATS Bryant s full line of wall thermostats are designed to enhance every PTAC application. Wall thermostats are simple and easy to use. Wall thermostats provide better temperature and humidity control as they can be placed in an optimal position in the room. Mode HOLD Off Heat Cool AUTO Fan On AUTO COOL HEAT PROGRAMING Digital Programmable Thermostat Part No.: TSTATBBPAC01-B (for heat/cool models) Part No.: TSTATBBPHP01-B (for heat pump models) This microcomputer-controlled, 7-day programmable wall thermostat has enhanced features that provide automatic control for both heat pumps and heating/cooling units. It is used only on wall thermostat control (RC,RP) models. PROGRAMMABLE THERMOSTAT Builder s Model Thermostat Part No.: TSTATBBBAC01-B (for heat/cool models) Part No.: TSTATBBBHP01-B (for heat pump models) This low-voltage, easy-to-use non-programmable thermostat provides maximum guest comfort. This thermostat can only be used on wall thermostat (RC,RP) models. HEAT COOL EMHT FAN SET MODE FAN BUILDER S MODEL THERMOSTAT Wall Thermostat Interface Retrofit Kit Part No.: RC-FIELDKIT230HC Part No.: RC-FIELDKIT230HP Part No.: RC-FIELDKIT265HC Part No.: RC-FIELDKIT265HP The Wall Thermostat Interface Retrofit Kit allows PTAC units with standard unit-mounted controls to be field converted for use with wall thermostat controls. WALL THERMOSTAT COMFORT WALL THERMOSTAT INTERFACE RETROFIT KIT Thermostat Locking Cover Part No.: TSTAT-COVER-6X7 Part No.: TSTAT-COVER-7X10 The thermostat locking cover prevents unauthorized access to the thermostat. THERMOSTAT LOCKING COVER 8

ACCESSORIES (cont) Condensate Drain Kit Part No.: DRAIN-KIT-4PK This universal drain kit may be used internally or externally to route condensate to a drainage system. It can be field-installed on any Bryant wall sleeve. Although the units are designed to dissipate all the condensate generated during normal cooling, there may be times when abnormal conditions cause more condensate than the unit can dissipate. If condensate that drips from the wall sleeve is objectionable, this internal/external drain kit should be installed. The drain kit may be attached to the exterior right or left side of the wall sleeve for external draining or may be mounted to the room side of the wall sleeve for internal draining. IMPORTANT: For internal drains installed in the plastic wall sleeve, the drain must be installed on the flat area of the sleeve. It cannot be installed in the wafer area. DRAIN KIT Lateral Duct Kit Part No.: 84-LATERAL-DUCT (Adapter Plenum and Extension) The accessory lateral duct kit allows one unit to heat or cool two rooms. The kit provides substantial savings for apartments, hotel suites, and office suites by eliminating the need for separate units for every room. The amount of air that can be diverted to an adjoining room is adjustable from 20 to 30 percent. The lateral duct kit consists of two main components, the plenum and the extension duct. The kit mounts to the wall sleeve and allows either right or left side ducting. Consider the following when designing a ducted application. The maximum extension of the duct length is 4 feet. The duct run must be straight and horizontal; no bends or turns. The minimum recommended clearance between the unit and the adjoining room wall is 6 inches. You must provide for return air from the adjoining room. Bryant 840/841/842 units are not qualified for use with any other ducting scheme. See page 13 for more information. NOTES: 1. Lateral Duct Kit includes wall register for duct extension. 2. The sleeve should extend a minimum of 3-in. into the room to install mounting brackets. 3. The Lateral Duct Kit is not compatible with previous PTAC models. LATERAL DUCT KIT 9

ACCESSORIES (cont) Lateral Air Deflector Part No.: DEFLECTOR-1PK Bryant s exclusive lateral air deflector allows discharge air to be directed right or left in a room. This field-installed accessory is equipped with independently adjustable louvers to enhance air circulation. Lateral air deflectors are recommended for units mounted in a corner or off-center in a room. NOTE: The lateral air deflector is not compatible with previous PTAC models. ACCESSORY AIR DEFLECTOR Curtain Deflector Part No.: 84-CURTDFL-1PK The curtain deflector is used to prevent curtains from being blown into the discharge air. Security Door Kit Part No.: 84-SECURITY-DOOR This key-locking security door kit prevents unauthorized access to the unit s heating and cooling controls and prevents tampering with units in public locations and institutions. This fieldinstalled accessory includes two matching keys and fits all Bryant 840/841/842 models. Keys are common to all Security Door kits. CURTAIN DEFLECTOR KIT SECURITY DOOR KIT Replacement Filters Part No.: 84-FILTER-10PK The Bryant 840/841/842 model replacement air filters come in packages of 10. The filters save energy by preventing the evaporator coils from being plugged with dirt and lint. These economical and sturdy filters are interchangeable and may be washed, vacuumed, and reused. Energy Management Kit Part No.: EM-KIT This field-installed accessory kit allows individual units to be turned on and off from a remote location. The kit incorporates Bryant s Freeze Guard protection that prevents rooms from freezing during extreme or extended cold periods. Under these conditions, the Freeze Guard automatically disables front desk control and allows the unit to maintain a temperature of at least 50 F in the room. When the room reaches 65 F, the Freeze Guard feature returns the unit control to the front desk. This kit interfaces to most energy management systems. When installed in locations other than the front desk, the kit can control unit operation by receiving signals from field-supplied devices such as motion sensors or heat sensing detectors. Control devices connected to the Energy Management Kit must have normally open sets of contacts (when the switch is open, the unit operates). A 24-volt transformer must be field supplied and connected to the Energy Management Kit. EASILY REPLACEABLE FILTERS ENERGY MANAGEMENT KIT 10

BASE UNIT DIMENSIONS NOTES: 1. Dimensions in parenthesis are in millimeters. 2. Minimum opening sizes apply to all wall openings. 3. Proper building practices must be used when constructing a wall opening to support a PTAC wall sleeve and chassis. If practices are unknown consult your local architect or building contractor. 4. Installed wall sleeve must be level from side to side and front to back (do not use rails to level sleeve). 5. If wall sleeve extends into the room more than 4-in., an accessory subbase or field fabricated front support should be used to prevent wall sleeve from tipping forward. 6. For all applications with an accessory subbase, wall sleeve must extend into room 3 1 / 4-in. (83 mm) minimum and 3 1 / 4-in. (83 mm) minimum from floor. 7. For all applications with an accessory lateral duct, sleeve must extend into the room 3-in. (76.2 mm) minimum. In applications where the sleeve will not extend a minimum 3-in., the lateral duct mounting brackets must be mounted on the wall sleeve prior to wall sleeve installation. 8. Remote control models, RC and RP units, use low voltage connections (24 volt AC). 9. 265 volt cord connected units must plug into a 265 volt electrical subbase per UL requirement (or hardwire can be used). 10. The 265 volt electrical cord is approximately 15-in. long from where it exits the front panel. 11

ACCESSORY DIMENSIONS MAIN STUD JACK STUDS HEADER- 4 x 4 OR (2) 2 x 4 ON EDGE 16 1/4 STANDARD POLYMER NON-INSULATED WALL SLEEVE STANDARD POLYMER INSULATED WALL SLEEVE STANDARD METAL INSULATED WALL SLEEVE JACK STUD 42 1/8 42 CRIPPLE 16 FLOOR SUB-FLOOR 24 /26 /28 FRAMING AND MINIMUM WALL SLEEVE OPENING EXTENDED METAL INSULATED WALL SLEEVE NOTES (ALL SLEEVES): 1. Never install fasteners through bottom of sleeve. 2. Never use rails to level sleeve. Wall Sleeve Mounting (All Models) 12

ACCESSORY DIMENSIONS (cont) NOTE: For all applications with an accessory lateral duct, sleeve must extend into the room a minimum of 3-inches. In applications where the sleeve will not extend a minimum of 3-in., the lateral duct mounting brackets will need to be mounted on the sleeve prior to installation to the wall. Lateral Duct 13

ACCESSORY DIMENSIONS (cont) 0-3 1/4 MIN. (83) 0-5 1/2 MAX. (140) 0-0 7/8 (22) OUTSIDE WALL SUBBASE ACCESS COVERS SEE NOTES 19 1/2 SIDE 1 9/16 17 (3) 1 1/8 DIA. KNOCKOUTS (3) 7/8 DIA. KNOCKOUTS SUBBASE LEVELING BOLTS ACCESSORY DRAIN (EXTERNAL OR INTERNAL) VIEW A ACCESSORY SUBBASE ELECTRICAL CONNECTIONS NOTES: 1. Accessory subbase is required for applications where: Wall sleeve extends 4 or more inches into the room. Wall thickness is less than 2 inches. All 265 v cord connected applications. 2. For all applications with an accessory subbase: Wall sleeve must extend 4 in. minimum into the room and 3 1 / 4 in. minimum above the floor. Subbase height is adjustable from 3 1 / 4 in. minimum to 5 1 / 2 in. maximum above floor (including carpeting). Refer to wall sleeve installation instructions. Subbase 14

TYPICAL WALL INSTALLATION NOTES: 1. Sleeve may be flush mounted to floor, but front panel may have to be notched to accommodate service cord. 2. If more than 4 in. of sleeve projects into room, an accessory subbase must be used for support. 3. For walls 2 in. thick or less, an accessory subbase must be used for support. 4. Caulk around sleeve on both indoor and outdoor sides. Typical Wall Sleeve Installation Typical Curtain Wall Installation (All Models) 15

TYPICAL WALL INSTALLATION (cont) WARNING: Blocking indoor or outdoor discharge air could cause premature failure of unit. 15 MINIMUM DISTANCE FROM FRONT PANEL TO OBJECTS IN ROOM 36" MINIMUM DISTANCE FROM SLEEVE TO BUILDING WALLS, SHRUBS, WALKWAY, etc. Indoor and Outdoor Discharge Air Circulation 16

PERFORMANCE AND ELECTRICAL DATA UNIT 840 HEAT/COOL CATALOG NUMBERS COOLING BTU MOISTURE REMOVAL (pt/hr) EER ELECTRIC HEAT (Btuh) EVAP FAN (CFM) VENT AIRFLOW (CFM) SHIPPING WEIGHT (lbs) 840-N-07-2 7,000/ 6,900 1.5 11.3/11.3 7,800/ 6,400 260/250 125 230/208 2.7/2.9 10.4/ 9.5 619/ 611 2393/1985 15 24 0.78 1 840-N-07-3 7,000/ 6,900 1.5 11.3/11.3 11,600/ 9,700 260/250 125 230/208 2.7/2.9 15.2/14.1 619/ 611 3493/2935 20 24 0.78 2 840-N-09-2 9,000/ 8,900 2.4 11.0/11.0 7,800 /6,400 260/250 125 230/208 3.7/3.8 10.4/ 9.5 818/ 809 2393/1985 15 24 0.73 1 840-N-09-3 9,000/ 8,900 2.4 11.0/11.0 11,600/ 9,700 260/250 125 230/208 3.7/3.8 15.2/14.1 818/ 809 3493/2935 20 24 0.73 2 840-N-12-2 12,000/11,900 3.4 10.1/10.1 7,800/ 6,400 350/320 140 230/208 5.2/5.6 10.8/ 9.9 1188/1178 2470/2047 15 34 0.71 1 840-N-12-3 12,000/11,900 3.4 10.1/10.1 11,600/ 9,700 350/320 140 230/208 5.2/5.6 15.6/14.5 1188/1178 3570/2997 20 34 0.71 2 840-N-12-5 12,000/11,900 3.4 10.1/10.1 17,000/13,600 350/320 140 230/208 5.2/5.6 22.5/20.0 1188/1178 5170/4147 30 34 0.71 3 840-N-15-2 14,500/14,000 5.2 9.4/ 9.5 7,800/ 6,400 350/320 150 230/208 6.8/7.6 10.9/10.0 1543/1473 2517/2117 15 35 0.65 1 840-N-15-3 14,500/14,000 5.2 9.4/ 9.5 11,600/ 9,700 350/320 150 230/208 6.8/7.6 15.7/14.6 1543/1473 3617/3067 20 35 0.65 2 840-N-15-5 840-D-07-2 14,500/14,000 7,000 5.2 1.5 9.4/ 9.5 11.3 17,000/13,600 7,800 350/320 260 50 150 125 230/208 265 6.8/7.6 2.4 22.6/20.1 9.2 1543/1473 619 5217/4217 2396 30 15 35 26 0.65 0.78 3 4 840-D-07-3 7,000 1.5 11.3 11,600 260 125 265 2.4 13.3 619 3496 20 26 0.78 5 840-D-09-2 9,000 2.4 11.0 7,800 260 125 265 3.1 9.2 818 2396 15 24 0.73 4 840-D-09-3 9,000 2.4 11.0 11,600 260 125 265 3.1 13.3 818 3496 20 24 0.73 5 840-D-12-2 12,000 3.4 10.1 7,800 340 140 265 4.6 9.4 1188 2470 15 34 0.71 4 840-D-12-3 12,000 3.4 10.1 11,600 340 140 265 4.6 13.5 1188 3570 20 34 0.71 5 840-D-15-5 12,000 3.4 10.1 17,000 340 140 265 4.6 19.6 1188 5170 25 34 0.71 6 840-D-15-2 14,500 5.2 9.4 7,800 340 150 265 6.0 9.7 1543 2517 15 36 0.65 4 840-D-15-3 14,500 5.2 9.4 11,600 340 150 265 6.0 13.8 1543 3617 20 36 0.65 5 840-D-15-5 14,500 5.2 9.4 17,000 340 150 265 6.0 19.9 1543 5217 25 36 0.65 6 1-PH 60 Hz VOLTAGE Cooling CURRENT AMPS Elec. Ht. Cooling POWER WATTS Elec. Ht. BRANCH CIRCUIT FUSE AMPS R-22 CHARGE (oz) SENSIBLE HEAT RATIO RECEPTACLE TYPE UNIT 841 HEAT PUMP CATALOG NUMBERS COOLING BTU MOISTURE REMOVAL (pt/hr) EER REVERSE CYCLE COP ELECTRIC HEAT (Btuh) EVAP FAN (CFM) VENT AIRFLOW (CFM) 841-N-07-2 7,000/ 6,900 1.5 11.3/11.3 6,100/ 6,000 3.1/3.1 7,800/ 6,400 260/250 125 230/208 2.7/2.9 10.4/ 9.5 619/ 611 2393/1985 15 24 0.78 1 841-N-07-3 7,000/ 6,900 1.5 11.3/11.3 6,100/ 6,000 3.1/3.1 11,600/ 9,700 260/250 125 230/208 2.7/2.9 15.2/14.1 619/ 611 3493/2935 20 24 0.78 2 841-N-09-2 9,000/ 8,900 2.4 11.0/11.0 7,900/ 7,800 3.1/3.1 7,800/ 6,400 260/250 125 230/208 3.7/3.8 10.4/ 9.5 818/ 809 2393/1985 15 24 0.73 1 841-N-09-3 9,000/ 8,900 2.4 11.0/11.0 7,900/ 7,800 3.1/3.1 11,600/ 9,700 260/250 125 230/208 3.7/3.8 15.2/14.1 818/ 809 3493/2935 20 24 0.73 2 841-N-12-2 12,000/11,900 3.4 10.1/10.1 10,800/10,700 3.0/3.0 7,800/ 6,400 350/320 140 230/208 4.7/5.2 10.8/ 9.9 1188/1178 2470/2047 15 34 0.71 1 841-N-12-3 12,000/11,900 3.4 10.1/10.1 10,800/10,700 3.0/3.0 11,600/ 9,700 350/320 140 230/208 4.7/5.2 15.6/14.5 1188/1178 3570/2997 20 34 0.71 2 841-N-12-5 12,000/11,900 3.4 10.1/10.1 10,800/10,700 3.0/3.0 17,000/13,600 350/320 140 230/208 4.7/5.2 22.5/20.0 1188/1178 5170/4147 30 34 0.71 3 841-N-15-2 14,500/14,000 5.2 9.4/ 9.5 13,400/13,200 2.9/2.9 7,800/ 6,400 350/320 150 230/208 6.8/7.6 10.9/10.0 1543/1473 2517/2117 15 35 0.65 1 841-N-15-3 14,500/14,000 5.2 9.4/ 9.5 13,400/13,200 2.9/2.9 11,600/ 9,700 350/320 150 230/208 6.8/7.6 15.7/14.6 1543/1473 3617/3067 20 35 0.65 2 841-N-15-5 841-D-07-2 14,500/14,000 7,000 5.2 1.5 9.4/ 9.5 11.3 13,400/13,200 6,100 2.9/2.9 3.1 17,000/13,600 7,800 350/320 260 50 150 125 230/208 265 6.8/7.6 2.4 22.6/20.1 9.2 1543/1473 619 5217/4217 2396 30 15 35 26 0.65 0.78 3 4 841-D-07-3 7,000 1.5 11.3 6,100 3.1 11,600 260 125 265 2.4 13.3 619 3496 20 26 0.78 5 841-D-09-2 9,000 2.4 11.0 7,700 3.1 7,800 260 125 265 3.1 9.2 818 2396 15 24 0.73 4 841-D-09-3 9,000 2.4 11.0 7,700 3.1 11,600 260 125 265 3.1 13.3 818 3496 20 24 0.73 5 841-D-12-2 12,000 3.4 10.1 10,800 3.0 7,800 340 140 265 4.5 9.4 1188 2470 15 34 0.71 4 841-D-12-3 12,000 3.4 10.1 10,800 3.0 11,600 340 140 265 4.5 13.5 1188 3570 20 34 0.71 5 841-D-12-5 12,000 3.4 10.1 10,800 3.0 17,000 340 140 265 4.5 19.6 1188 5170 25 34 0.71 6 841-D-15-2* 14,500 5.2 9.4 13,400 2.9 7,800 340 150 265 6.0 9.7 1543 2517 15 36 0.65 4 841-D-15-3* 14,500 5.2 9.4 13,400 2.9 11,600 340 150 265 6.0 13.8 1543 3617 20 36 0.65 5 841-D-15-5* 14,500 5.2 9.4 13,400 2.9 17,000 340 150 265 6.0 19.9 1543 5217 25 36 0.65 6 SHIPPING WEIGHT (lbs) 1-PH 60 Hz VOLTAGE Cooling CURRENT AMPS Elec. Ht. Cooling POWER WATTS Elec. Ht. BRANCH CIRCUIT FUSE AMPS R-22 CHARGE (oz) SENSIBLE HEAT RATIO RECEPTACLE TYPE LEGEND COP Coefficient of Performance EER Energy Efficiency Ratio *Ratings are preliminary. See below for receptacle type. RECEPTACLE 15 Amps 250 Volts 20 Amps 250 Volts 30 Amps 250 Volts 15 Amps 265 Volts 20 Amps 265 Volts 25/30 Amps 265 Volts 17

PERFORMANCE AND ELECTRICAL DATA (cont) UNIT 842 COOL ONLY CATALOG NUMBERS COOLING BTU MOISTURE REMOVAL (pt/hr) EVAP FAN (CFM) VENT AIRFLOW (CFM) SHIPPING WEIGHT (lbs) EER Cooling Cooling 842-N-07-0 7,000/ 6,900 1.5 11.3/11.3 260/250 125 230/208 2.7/2.9 619/ 611 15 24 0.78 1 842-N-07-0 7,000/ 6,900 1.5 11.3/11.3 260/250 125 230/208 2.7/2.9 619/ 611 20 24 0.78 2 842-N-09-0 9,000/ 8,900 2.4 11.0/11.0 260/250 125 230/208 3.7/3.8 818/ 809 15 24 0.73 1 842-N-09-0 9,000/ 8,900 2.4 11.0/11.0 260/250 125 230/208 3.7/3.8 818/ 809 20 24 0.73 2 842-N-12-0 12,000/11,900 3.4 10.1/10.1 350/320 140 230/208 5.2/5.6 1188/1178 15 34 0.71 1 842-N-12-0 12,000/11,900 3.4 10.1/10.1 350/320 140 230/208 5.2/5.6 1188/1178 20 34 0.71 2 842-N-12-0 12,000/11,900 3.4 10.1/10.1 350/320 140 230/208 5.2/5.6 1188/1178 30 34 0.71 3 842-N-15-0 14,500/14,000 5.2 9.4/ 9.5 350/320 150 230/208 6.8/7.6 1543/1473 15 35 0.65 1 842-N-15-0 14,500/14,000 5.2 9.4/ 9.5 350/320 150 230/208 6.8/7.6 1543/1473 20 35 0.65 2 842-N-15-0 14,500/14,000 5.2 9.4/ 9.5 350/320 150 230/208 6.8/7.6 1543/1473 30 35 0.65 3 50 842-D-07-0 7,000 1.5 11.3 260 125 265 2.4 619 15 26 0.78 4 842-D-07-0 7,000 1.5 11.3 260 125 265 2.4 619 20 26 0.78 5 842-D-09-0 9,000 2.4 11.0 260 125 265 3.1 818 15 24 0.73 4 842-D-09-0 9,000 2.4 11.0 260 125 265 3.1 818 20 24 0.73 5 842-D-12-0 12,000 3.4 10.1 340 140 265 4.6 1188 15 34 0.71 4 842-D-12-0 12,000 3.4 10.1 340 140 265 4.6 1188 20 34 0.71 5 842-D-12-0 12,000 3.4 10.1 340 140 265 4.6 1188 25 34 0.71 6 842-D-15-0 14,500 5.2 9.4 340 150 265 6.0 1543 15 36 0.65 4 842-D-15-0 14,500 5.2 9.4 340 150 265 6.0 1543 20 36 0.65 5 842-D-15-0 14,500 5.2 9.4 340 150 265 6.0 1543 25 36 0.65 6 1-PH 60 Hz VOLTAGE CURRENT AMPS POWER WATTS BRANCH CIRCUIT FUSE AMPS R-22 CHARGE (oz) SENSIBLE HEAT RATIO RECEPTACLE TYPE* LEGEND EER Energy Efficiency Ratio *See below for receptacle type. RECEPTACLE 15 Amps 250 Volts 20 Amps 250 Volts 30 Amps 250 Volts 15 Amps 265 Volts 20 Amps 265 Volts 25/30 Amps 265 Volts 18

TYPICAL WIRING DIAGRAMS COMPONENT LEGEND Component Connection (Marked) Component Connection (Unmarked) Accessory or Optional Wiring To Indicate Common Potential Only Not To Represent Wire CAP Capacitor COMP Compressor FM Fan Motor FCS Fan Cycle Switch HTR Heater IT Indoor Thermostat OFT Outdoor Frost Thermostat OL Overload PLS Primary Limit Switch RVS Reversing Valve Solenoid SLS Secondary Limit Switch ST Start Thermistor SW Switch NOTES: 1. Recommended for use on grounded power supply only. 2. Compressor and fan motor thermally protected. 3. Use copper conductors only. 4. All wiring must conform with N.E.C. and local codes. 5. Dashed lines indicate components when used. 6. OFT determines whether to bring on compressor heat or electric heat. Typical Wiring Schematic for 841 Standard Heat Pump Units 19

TYPICAL WIRING DIAGRAMS (cont) TYPICAL THERMOSTAT INTERFACE T STAT OUTPUT: RC CONTROLER OUTPUT: UNIT OPERATION: G 24 VAC G 0 VAC FR LINE VAC FR 0 VAC FAN Y 24 VAC O 0 VAC HR1 & HR2 LINE VAC RVR LINE VAC HEATING W 24 VAC HR1 & HR2 LINE VAC HEATING Y 24 VAC O 24 VAC CR LINE VAC RVR 0 VAC COOLING R 24 VAC R 24 VAC OUTPUT POWER TO WALL C COMMON C COMMON THERMOSTAT 1. If W is ON, then FR is forced ON (regardless of G ) & CR is forced OFF. 2. If Y is ON, then FR is forced ON (regardless of G ). 3. If IFT (indoor coil) is < 35 F, then CR is forced OFF until IFT is > 39 F. COMPONENT LEGEND Component Connection (Marked) FM Fan Motor ST Start Thermistor Component Connection (Unmarked) HTR Heater TRANS Transformer Terminal Board Connection IFT Indoor Frost Thermostat PCBD Printed Circuit Board Field Splice OFT Outdoor Frost Thermostat HR1 Heater Relay Field Control Wiring OL Overload HR2 Heater Relay Accessory or Optional Wiring PLS Primary Limit Switch CR Compressor Relay To Indicate Common Potential Only Not To Represent Wire RVS Reversing Valve Solenoid FR Fan Relay CAP Capacitor SLS Secondary Limit Switch RVR Reversing Valve Relay COMP Compressor SSS Speed Selector Switch NOTES: 1. Recommended for use on grounded power supply only. 2. Compressor and fan motor thermally protected. 3. Use copper conductors only. 4. All wiring must conform with N.E.C. and local codes. 5. Dashed lines indicate components when used. 6. Field control wire suitable for N.E.C. class 2 control circuit, at 24 volts. 7. OFT determines whether to bring on compressor heat or electric heat. Typical Wiring Schematic for 841 Wall Thermostat Control Heat Pump Units 20

TYPICAL WIRING DIAGRAMS (cont) Typical Wiring Schematic for 840 Standard Heat/Cool Units 21

TYPICAL WIRING DIAGRAMS (cont) Typical Wiring Schematic for 840 Wall Thermostat Control Heat/Cool Units 22

TYPICAL WIRING DIAGRAMS (cont) Typical Wiring Schematic for 842 Standard Cooling Only Units 23

TYPICAL WIRING DIAGRAMS (cont) FRONT DESK SWITCH PANEL ROOM 100 ROOM 101 ROOM N FIELD-SUPPLIED 24-V TRANSFORMER (SEE NOTE 1) B W B W B W PTAC #1 PTAC #2 PTAC #N LEGEND AWG American Wire Gage B Black PTAC Packaged Terminal Air Conditioner W White NOTES: 1. To size transformer, use the following equation: Quantity of PTAC units x 12 va = Transformer Size (va) Example: 110 PTAC Units x 12 va = 1320 va Transformer 2. Following are recommended wire sizes: AWG WIRE SIZE NO. MAXIMUM LENGTH (ft) 24 400 22 600 20 900 18 1500 16 2000 Energy Management Kit 24

Mode Off Heat Cool AUTO Fan On AUTO HOLD CLEAN FILTER COOL HEAT PROGRAMING TYPICAL WIRING DIAGRAMS (cont) MASTER PTAC R Y W R Y W T STAT G G O O C C UNIT 1 R Y W G O C UNIT 2 R Y W G O C CAUTION: All units must be connected to same ground source. To accomplish this, be sure to connect all units back to the same breaker box. UNIT 3 R Y W G O C NOTES: 1. Do not daisy chain R (24 VAC). 2. Maximum of 4 PTAC units can be connected to one single wall thermostat. Multiple PTAC Units Connected to a Single Wall Thermostat 25

PACKAGED TERMINAL COOLING UNIT WITH HEAT PUMP OR ELECTRIC HEATING HVAC GUIDE SPECIFICATIONS SIZE RANGE: COOLING:6,900 TO 14,500 BTUH HEATING: 6,000 TO 13,400 BTUH (HEAT PUMP) 6,400 TO 17,000 BTUH (ELECTRIC HEAT) BRYANT MODEL NUMBERS: 840 COOLING UNIT WITH ELECTRIC HEAT 841 HEAT PUMP UNIT WITH ELECTRIC HEAT 842 COOLING ONLY UNIT PART 1 General 1.01 SYSTEM DESCRIPTION Single piece, thru-the-wall electrically controlled unit using hermetic rotary compressor for cooling and heat pump or electric resistance heat, as shown on the contract drawings. 1.02 QUALITY ASSURANCE Unit shall be rated in accordance with ARI Standard 310/ 380-93 and certified by UL and UL, Canada. 1.03 DELIVERY, STORAGE, AND HANDLING Unit shall be stored and handled per manufacturer's recommendations. PART 2 Products 2.01 EQUIPMENT A. General: Factory-assembled, single-piece, heating and cooling unit. Contained within the unit enclosure shall be compressor, coils, fans and fan motor, heating means, controls, all wiring and piping, and a full refrigerant charge (R-22). B. Front Panel (supplied with unit): Front panel shall be of plastic material with filters integrated and louvers in front surface. C. Filters: Supply air filters shall be two, front-access, interchangeable, washable, permanent type that filter the supply air. Outdoor air filter shall be a one-piece, washable type filter. D. Anti-Theft Control Knobs: Control knobs shall be captured by the front panel to prevent theft. E. Bi-Directional Discharge Grille: Discharge grille shall be easily adjustable and bidirectional. In one direction, the air will discharge 40 degrees from horizontal. In the other direction, the air will discharge 80 degrees from horizontal. F. Fans and Motor: 1. Evaporator (indoor) fan shall be a single-inlet, corrosion-resistant, reverse curve blower, discharging air upwards. Fan shall be dynamically balanced. 2. Condenser (outdoor) fan shall be a propeller type with corrosion-resistant plastic finish, discharging air out the rear of the unit. Fan shall be dynamically balanced with an integrated slinger ring. 3. Fan motor shall be totally enclosed, permanently lubricated, and multiple speed. GUIDE SPECIFICATIONS G. Condenser Shroud: The condenser shroud shall be 2 pieces and secured by captured screws for easy access to service and maintain components in the condenser section. H. Snow Baffle: A snow baffle shall be included to prevent snow from melting on the fan motor and freezing to the fan shaft. I. Compressor: The compressor shall be fully hermetic with internal and external vibration isolation. J. Factory-Installed Electric Heater: Electric heater shall be standard in heat/cool and heat pump units. K. Coils: The coils shall have aluminum plate fins mechanically bonded to seamless copper tubes internally enhanced (grooved) with all joints brazed. L. Refrigerant Components: All piping, compressor, and expansion devices shall be included. M. Controls and Safeties: 1. All standard models shall be equipped with electromechanical controls and no electronics for low cost serviceability. 2. Controls shall consist of rotary selector switch which provides OFF/FAN/HEAT/COOL operation, an adjustable thermostat with upper and lower limits, VENT OPEN/CLOSE, and FAN CYCLE switches. Additional controls for heat pumps include outdoor coil defrost thermistor. 3. Safeties shall consist of automatic reset overtemperature and overcurrent protection for compressor, inherent, inherent automatic reset overtemperature protection for fan motor; two overtemperature protectors for heater. 4. Standard controls for unit operation shall be a mechanical rotary-type switch, easily accessible and covered by a hinged door. 5. Wall thermostat units (RC models) shall come from the factory wall thermostat ready, with no fieldinstalled kits required and including a blank out plate for the control knobs. 6. A continuous/fan cycle selector switch shall allow continuous fan operation for highest comfort or cycle operation (fan only runs with the compressor or electric heater) for maximum energy savings. 7. Temperature limiting shall limit the movement of the thermostat control knob to prevent extreme settings. 8. Emergency heat switch for heat pump units shall disable the compressor in heating mode and only allow electric heating. N. Two-Stage Condensate Removal System: A two-stage condensate removal system shall be used. The first stage shall be a slinger ring integrated into the outdoor fan to disperse condensate onto the condensate coil to be evaporated. The second stage shall be a vortex hole to atomize condensate into the air stream and disperse it onto the condensate coil for evaporation. 26

O. Fresh Air Vent: The fresh air vent shall be operated by a concealed manual control and shall have a magnet on the door to ensure closure. When the vent is open, the unit shall supply 50 cfm of fresh air. P. Operating Characteristics: Unit shall be capable of starting and running at 115 F ambient outdoor temperature per maximum load criteria of ARI Standard 310/380. Q. Electrical Requirements: All units are provided with power cords. The 265-Volt unit requires a field-installed electrical subbase accessory. 230/208-Volt: Shall be prewired with plug to use with appropriate wall receptacle as specified on unit nameplate. 265-Volt: Shall be either cord-connected or hardwired into field-installed electrical subbase. R. Corrosion Protection (CP, RP): Corrosion protection shall be available for coastal and corrosive environments to protect against harsh conditions. The minimum requirements shall be: 1. All outdoor-exposed sheet metal parts shall be coated with a polyester powder coat paint. 2. Compressor and outdoor fan motor finish shall be capable of withstanding 500 hours of salt spray testing per ASTM B-117. 3. Compressor mounting screws shall be Sermagard coated. 4. Outdoor coil fin stock shall be coated and able to withstand 1000 hours of salt spray testing per ASTM B-117. 5. Outdoor coil tube sheets shall be made of 316L stainless steel. S. Special Features: 1. Insulated Polymer Wall Sleeve (UL94-5V rated): Polymer wall sleeve shall provide mounting for unit chassis. 2. Deep Wall Metal Wall Sleeve (up to 28-in.): The deep wall metal wall sleeve shall be a one piece extended wall sleeve with deep wall baffles integrated. GUIDE SPECIFICATIONS (cont) 3. Architectural Grille (polymer or aluminum): Architectural grilles shall provide protection to outside of unit and are provided in a range of colors. Polymer grilles are used for long durable life or painted aluminum grilles are used for a superior color match to the building. 4. Subbase: The subbase shall be pre-assembled from the factory and come with factory options electrical (receptacle and hardwire) or non-electrical. The subbase shall be UL listed and shall provide unit support when the wall sleeve is not adequately supported by the wall. 5. Hardwire Kit: The hardwire kit shall provide a permanent connection to the unit. The hardwire kit provides 36-in. of flexible conduit and a Molex connector for easy connection to the unit. 6. Condensate Drain Kit (left, right, or internal): Condensate drain kit shall install on the wall sleeve and provide a means to remove the condensate through a drainage hose. 7. Lateral Duct Kit: The lateral duct kit shall allow one unit to heat or cool two rooms. The duct shall be 18 gage metal with up to 30% airflow into an adjacent room. 8. Energy Management Interface Kit: The energy management interface kit allows individual units to be turned off or on from a remote location. 9. Lateral Air Deflector: The lateral air deflector shall allow the discharge air to be directed right or left in the room. 10. Security Door Kit: The security door kit shall prevent unauthorized access to the unit s heating and cooling controls. Common keys shall be provided. 11. Wall Thermostats: Thermostat shall be digital, 24-v thermostats and shall provide remote control operation when wired to the unit. 27

84 Series Packaged Terminal Air Conditioner Warranty FULL ONE-YEAR WARRANTY During the first year after purchase, CAC/BDP will, through its authorized independent servicing dealers or service stations*, and free of charge to the user or subsequent users, repair or replace any parts which are defective in material or workmanship. The replacement part can be a new or remanufactured part as provided at CAC/BDP s sole option. FULL EXTENDED FOUR-YEAR WARRANTY ON SEALED REFRIGERATION SYSTEM ONLY During the second through fifth years after date of original purchase, CAC/BDP will, through its authorized servicing dealers and service stations* and free of charge to the end user or subsequent users, repair or replace the compressor, condenser, evaporator or connecting tubing if defective in material or workmanship. This includes system refrigeration charge. The replacement part can be new or a remanufactured part as provided at CAC/BDP s sole option. LIMITED EXTENDED FOUR-YEAR WARRANTY ON NON-SEALED REFRIGER- ATION SYSTEM ONLY During the second through fifth years after date of original purchase, CAC/BDP will, through its authorized servicing dealers and service stations and free of charge to the end user or subsequent users, repair or replace any non-sealed system part (motor, solenoid, thermistor, thermostat, relays, switch, capacitor, overload, drain valve, bulb heater, fan, stator) if defective in material or workmanship. The replacement part can be new or a remanufactured part at CAC/BDP s sole option. THIS LIMITED WARRANTY DOES NOT INCLUDE LABOR, user is responsible for labor, including cost of diagnosis of problem, removal and transportation of the air conditioner to and from the service center, and reinstallation charges necessary to accomplish repair. LIMITATION OF WARRANTIES ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH EACH LIMITED WARRANTY IS GIVEN AND APPLIES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER. ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY. CAC/BDP WILL NOT BE RESPONSIBLE FOR: 1. CLEANING REQUIRED PRIOR TO WARRANTY REPAIR. 2. Standard maintenance, cleaning or damage resulting from failure to perform normal maintenance as outlined in the owner s manual. 3. Instruction on methods of control and use of air conditioning unit after initial installation. 4. Damage or repairs needed as a consequence of faulty installation or application. This is the responsibility of the installer. 5. Failure to start due to voltage conditions, blown fuses, open circuit breakers or any other damages due to the inadequacy or interruption of electrical services. 6. Damage or repairs needed as a consequence of any misapplication, abuse, unauthorized alteration, improper servicing or operation. 7. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environment, or other conditions beyond the control of CAC/BDP. EXCEPTION TO CORROSIVE ENVIRONMENT IN ABOVE PARAGRAPH Packaged terminal units (84 Series) built with corrosion protection are exempt from the exclusion Corrosive Environment. The unit model number is identified on the nameplate with a CP suffix. 8. Reimbursement for replacement parts or repair services which are not supplied or designated by CAC/BDP and which are specifically covered under this warranty. 9. CAC/BDP products installed outside the continental U.S.A., Alaska, Hawaii and Canada. 10. Shipping damage or damage as a result of transporting the unit. This is the responsibility of the selling dealer or the authorized Room Air Conditioner service station. 11. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COM- MERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. 12. Warranty coverage of accessory items (wall thermostats, wall sleeves, etc.). NOTE: Service and Maintenance items excluded in this warranty may be covered by a separate service agreement through the seller at time of purchase. *Authorized independent dealers or service stations are registered with CAC/BDP Air Conditioning through its distributor organization. Please call toll-free 1-877-875-3362 for a local dealer. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Catalog No. 530-122 (Rev. 3/02) SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE UNIT MUST BE INSTALLED IN ACCORDANCE WITH INSTALLATION INSTRUCTIONS Copyright 2002 Bryant Heating & Cooling Systems Printed in U.S.A. 7/02 Catalog No. 5284-000