(1-800-492-8826)
FANGE HEATERS OVERVIEW WATTCO flange heaters are made using hairpin or bugle type tubular elements using incoloy sheathed elements that are welded or silver-brazed into a pipe or steel flange. Perfectly designed to be mounted in tanks and pressurized vessels, WATTCO flange heaters are used for heating liquid mediums or other specific types of liquids, and for heating gases (water, oil, heat transfer fluid, and corrosive solutions). EY FEATURES Standard heaters: ½ to 42 sizes. 0.260, 0.315, 0.375, 0.430 or 0.475, 0.625 diameter copper, steel, stainless steel. 150lb or 300lb forged steel flange Incoloy, Inconel, stainless steel, copper or titanium elements. Available explosion and/or moisture resistant terminal enclosures upon request. Available special sizes, wattages, and materials upon request. Heating units are custom-designed to meet your specifications. ENEFITS Easy to install Easy to maintain Perfect for higher kilowatt output applications Appropriate heater size provided for the application and fit Designed and built for safety FACTORS Please consider the following factors in order to select the proper flange heater: Flange size and pressures Heating element watt density ength of your tank Sheath material (corrosive or non corrosive) Temperature of the corrodent Degree of aeration of exposed corrodent Velocity of the corrodent The following sections will help you select the best WATTCO flange heater that will meet the requirements of your application. Please call us at 1.800.4WATTCO (1.800.492.8826) if you need any further assistance. SEECTING YOUR WATTCO FANGE HEATER GENERA RECOMMENDATIONS - FANGE HEATERS - 2 1/2 3 4 5 6 8 10 12 14 APPICATIONS Clean water, Freeze protection, Hot water storage, oiler and water heaters, Cooling towers, Solutions not corrosive to copper Hot water, Steam boilers, Mildly corrosive solutions (in rinse tanks, spray washers) Oils, Gases, Mildly corrosive liquids, Stagnant or heavy oils, High temperature, low flow gas heating Process water, Soap and detergent solutions, Soluble cutting oils, Demineralized or deionized water SHEATH MATERIA FANGE MATERIA HEATER TYPE Copper Steel FC Incoloy Steel FI Steel Steel FI Stainless Steel FI Mildly corrosive solutions Stainless Stainless FI Severe corrosive solutions, Demineralized water Incoloy Stainless FI ight oil, Medium oil Steel Steel FO Food equipment, Food equipment with cutout Incoloy Stainless FI Incoloy and Inconel are registered trademarks of Inco Alloys International 2 (1-800-492-8826)
FANGE HEATERS 2 1/2 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS G COD END H F DIA. E HOES ON A C.C. D DIA. es Available A HEATER DIMENSION IN INCHES FANGE FANGE RATING A C D E F G H Moisture resistant Explosion resistant 2 1/2 150 lb. 2 7/8 5 1/2 7 4 3/4 7/8 5 1/2 300 lb. 2 7/8 5 7/8 7 1/2 8 7/8 1 5 1/2 TAE 1 2 1/2-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 WATT DENSITY W/in. 2 WITHOUT WITH NET WT. S (approx.) COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 5 406 16 1 or 3 Phase 61.7 FC305X2016 FC305X2016T 16 10 635 25 " 64.9 FC310X2025 FC310X2025T 18 15 889 35 " 63.8 FC315X2035 FC315X2035T 18 20 1118 44 64.9 FC320X2044 FC320X2044T 20 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 5 406 16 1 or 3 Phase 61.7 FI305X2016 FI305X2016T 16 10 635 25 " 64.9 FI310X2025 FI310X2025T 18 15 864 34 " 66.1 FI315X2034 FI315X2034T 18 20 1118 44 64.9 FI320X2044 FI320X2044T 20 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 5 813 32 1 or 3 Phase 23.7 FO305X2032 FO305X2032T 16 10 1499 59 " 23.3 FO310X2059 FO310X2059T 18 12 1829 72 " 22.4 FO312X2072 FO312X2072T 20 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 2 813 32 1 or 3 Phase 9.5 FO302X2032 FO302X2032T 18 3 1219 48 " 8.8 FO303X2048 FO303X2048T 18 4 1448 57 " 9.7 FO304X2057 FO304X2057T 20 WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS (1-800-492-8826) 3
FANGE HEATERS 3 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available D DIA. G A COD END H Moisture resistant TAE 2 3-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY Explosion resistant F DIA. E HOES ON A C.C. WATT DENSITY W/in. 2 FANGE 3 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 3 1/2 6 7 1/2 4 3/4 15/16 5 1/2 300 lb. 3 1/2 6 5/8 8 1/4 8 7/8 1 1/8 5 1/2 WITHOUT WITH 5 406 16 1 or 3 Phase 61.7 FC305X2416 FC305X2416T 16 7 508 20 " 61.7 FC307X2420 FC307X2420T 16 10 635 25 " 64.9 FC310X2425 FC310X2425T 18 15 889 35 " 63.8 FC315X2435 FC315X2435T 18 20 1118 44 " 64.9 FC320X2444 FC320X2444T 20 30 889 35 " 63.8 FC630X2435 FC630X2435T 24 40 1118 44 " 64.9 FC640X2444 FC640X2444T 28 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 5 406 16 1 or 3 Phase 61.7 FI305X2416 FI305X2416T 16 7 483 19 " 66.4 FI307X2419 FI307X2419T 16 10 635 25 " 64.9 FI310X2425 FI310X2425T 18 15 864 34 " 66.1 FI315X2434 FI315X2434T 18 20 1118 44 " 64.9 FI320X2444 FI320X2444T 20 30 889 35 " 63.8 FI630X2435 FI630X2435T 25 40 1118 44 " 64.9 FI640X2444 FI640X2444T 30 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 5 813 32 1 or 3 Phase 23.7 FO305X2432 FO305X2432T 16 7 1118 44 " 22.7 FO307X2444 FO307X2444T 16 10 1499 59 " 23.3 FO310X2459 FO310X2459T 18 12 1829 72 " 22.4 FO312X2472 FO312X2472T 20 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 2 813 32 1 or 3 Phase 9.5 FO302X2432 FO302X2432T 18 3 1219 48 " 8.8 FO303X2448 FO303X2448T 18 4 1448 57 " 9.7 FO304X2457 FO304X2457T 20 NET WT. S (approx.) WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS 4 (1-800-492-8826)
FANGE HEATERS 4 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available G COD END H Moisture resistant Explosion resistant F DIA. E HOES ON A C.C. D DIA. A TAE 3 4-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY WATT DENSITY W/in. 2 FANGE 4 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 5 7 1/2 9 8 3/4 15/16 5 1/2 300 lb. 5 7 7/8 10 8 7/8 1 1/4 5 1/2 WITHOUT WITH 5 279 11 1 or 3 Phase 61.7 FC605X2811 FC605X2811T 16 7 330 13 " 61.7 FC607X2813 FC607X2813T 16 10 406 16 " 61.7 FC610X2816 FC610X2816T 18 15 533 21 " 61.7 FC615X2821 FC615X2821T 18 20 635 25 " 64.9 FC620X2825 FC620X2825T 20 25 559 22 64.3 FC925X2822 FC925X2822T 23 30 635 25 " 64.9 FC930X2825 FC930X2825T 24 40 787 31 " 65.8 FC940X2831 FC940X2831T 28 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 5 279 11 1 or 3 Phase 61.7 FI605X2811 FI605X2811T 16 7 330 13 " 61.7 FI607X2813 FI607X2813T 16 10 406 16 " 61.7 FI610X2816 FI610X2816T 18 15 533 21 " 61.7 FI615X2821 FI615X2821T 18 20 635 25 " 64.9 FI620X2825 FI620X2825T 20 25 559 22 64.3 FI925X2822 FI925X2822T 23 30 635 25 " 64.9 FI930X2825 FI930X2825T 25 40 787 31 " 65.8 FI940X2831 FI940X2831T 30 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 5 381 15 1 or 3 Phase 22.8 FO905X2815 FO905X2815T 16 7 483 19 " 22.1 FO907X2819 FO907X2819T 16 10 610 24 " 22.8 FO910X2824 FO910X2824T 18 12 686 27 " 23.5 FO912X2827 FO912X2827T 20 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 2 381 15 1 or 3 Phase 9.1 FO902X2815 FO902X2815T 18 3 457 18 " 10.3 FO903X2818 FO903X2818T 18 4 559 22 " 10.3 FO904X2822 FO904X2822T 20 NET WT. S (approx.) WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS (1-800-492-8826) 5
FANGE HEATERS 5 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available Moisture resistant Explosion resistant G COD END H F DIA. E HOES ON A C.C. D DIA. A TAE 4 5-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY WATT DENSITY W/in. 2 FANGE 5 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 5 8 1/2 10 8 7/8 15/16 6 3/4 300 lb. 5 9 1/4 11 8 7/8 1 3/8 6 WITHOUT WITH 10 406 16 1 or 3 Phase 66.7 FC610X3016 FC610X3016T 25 15 533 21 " 64.9 FC615X3021 FC615X3021T 27 20 635 25 " 67.6 FC620X3025 FC620X3025T 27 25 559 22 " 67.4 FC925X3022 FC925X3022T 32 30 635 25 " 67.6 FC930X3025 FC930X3025T 35 40 787 31 " 67.8 FC940X3031 FC940X3031T 37 50 965 38 " 65.8 FC950X3038 FC950X3038T 39 55 1041 41 " 66.0 FC955X3041 FC955X3041T 42 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 10 406 16 1 or 3 Phase 66.7 FI610X3016 FI610X3016T 25 15 533 21 " 64.9 FI615X3021 FI615X3021T 27 20 635 25 " 67.6 FI620X3025 FI620X3025T 27 25 559 22 " 67.4 FI925X3022 FI925X3022T 32 30 635 25 " 67.6 FI930X3025 FI930X3025T 35 40 787 31 " 67.8 FI940X3031 FI940X3031T 37 50 965 38 " 65.8 FI950X3038 FI950X3038T 39 55 1041 41 " 66.0 FI955X3041 FI955X3041T 43 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 5 381 15 1 or 3 Phase 24.9 FO905X3015 FO905X3015T 16 7 483 19 " 23.5 FO907X3019 FO907X3019T 16 10 610 24 " 23.8 FO910X3024 FO910X3024T 18 12 686 27 " 24.4 FO912X3027 FO912X3027T 20 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 2 381 15 1 or 3 Phase 10.0 FO902X3015 FO902X3015T 18 3 457 18 " 11.0 FO903X3018 FO903X3018T 18 4 559 22 " 10.8 FO904X3022 FO904X3022T 20 NET WT. S (approx.) WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS 6 (1-800-492-8826)
FANGE HEATERS 6 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available Moisture resistant Explosion resistant D DIA. G COD END H A TAE 5 6-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. (1-800-492-8826) VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY F DIA. E HOES ON A C.C. WATT DENSITY W/in. 2 WITHOUT WITH 30 533 21 1 or 3 Phase 64.9 FC1230X1021 FC1230X1021T 52 40 635 25 " 67.6 FC1240X1025 FC1240X1025T 52 45 711 28 " 65.3 FC1245X1028 FC1245X1028T 52 50 762 30 " 66.3 FC1250X1030 FC1250X1030T 52 60 737 29 " 66.5 FC1560X1029 FC1560X1029T 62 70 838 33 " 65.8 FC1570X1033 FC1570X1033T 66 80 914 36 " 67.5 FC1580X1036 FC1580X1036T 70 90 1016 40 " 66.8 FC1590X1040 FC1590X1040T 70 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 30 533 21 1 or 3 Phase 64.9 FI1230X1021 FI1230X1021T 52 35 584 23 " 66.4 FI1235X1023 FI1235X1023T 52 40 635 25 " 67.6 FI1240X1025 FI1240X1025T 52 45 711 28 " 65.3 FI1245X1028 FI1245X1028T 52 50 762 30 " 66.3 FI1250X1030 FI1250X1030T 52 60 737 29 " 66.5 FI1560X1029 FI1560X1029T 62 70 838 33 " 65.8 FI1570X1033 FI1570X1033T 66 80 914 36 " 67.5 FI1580X1036 FI1580X1036T 70 90 1016 40 " 66.8 FI1590X1040 FI1590X1040T 70 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 15 559 22 1 or 3 Phase 24.3 FO1515X1022 FO1515X1022T 51 20 686 27 " 24.4 FO1520X1027 FO1520X1027T 55 25 813 32 " 24.4 FO1525X1032 FO1525X1032T 65 30 965 38 " 23.7 FO1530X1038 FO1530X1038T 67 35 1092 43 " 23.8 FO1535X1043 FO1535X1043T 68 40 1219 48 " 23.9 FO1540X1048 FO1540X1048T 70 45 1346 53 " 24.0 FO1545X1053 FO1545X1053T 74 60 1753 69 " 23.8 FO1560X1069 FO1560X1069T 83 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 10 787 31 1 or 3 Phase 10.2 FO1510X1031 FO1510X1031T 52 15 1143 45 " 9.7 FO1515X1045 FO1515X1045T 65 20 1448 57 " 9.8 FO1520X1057 FO1520X1057T 78 NET WT. S (approx.) WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. FANGE CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS 6 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 5 9 1/2 11 8 7/8 1 6 3/4 300 lb. 5 10 5/8 12 1/2 12 7/8 1 7/16 6 7
FANGE HEATERS 8 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available G COD END H Moisture resistant Explosion resistant F DIA. E HOES ON A C.C. D DIA. A TAE 6 8-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY WATT DENSITY W/in. 2 FANGE 8 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 5 11 3/4 13 1/2 8 7/8 1 1/8 6 3/4 300 lb. 5 13 15 12 1 1 5/8 6 WITHOUT WITH NET WT. S (approx.) 50 584 23 1 or 3 Phase 63.3 FC1850X1223 FC1850X1223T 79 70 737 29 " 64.7 FC1870X1229 FC1870X1229T 82 90 889 35 " 65.5 FC1890X1235 FC1890X1235T 84 110 1041 41 " 66.0 FC18110X1241 FC18110X1241T 86 120 1118 44 " 66.2 FC18120X1244 FC18120X1244T 92 140 914 36 " 65.6 FC27140X1236 FC27140X1236T 95 180 1118 44 " 66.2 FC27180X1244 FC27180X1244T 125 210 1270 50 " 66.6 FC27210X1250 FC27210X1250T 125 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 50 584 23 1 or 3 Phase 63.3 FI1850X1223 FI1850X1223T 79 70 737 29 " 64.7 FI1870X1229 FI1870X1229T 83 90 889 35 " 65.5 FI1890X1235 FI1890X1235T 88 110 1041 41 " 66.0 FI18110X1241 FI18110X1241T 92 120 1118 44 " 66.2 FI18120X1244 FI18120X1244T 95 140 914 36 " 65.6 FI27140X1236 FI27140X1236T 110 160 1016 40 " 66.0 FI27160X1240 FI27160X1240T 114 180 1118 44 " 66.2 FI27180X1244 FI27180X1244T 118 210 1270 50 " 66.6 FI27210X1250 FI27210X1250T 126 250 1473 58 " 66.9 FI27250X1258 FI27250X1258T 130 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 40 762 30 1 or 3 Phase 23.6 FO2740X1230 FO2740X1230T 100 45 813 32 " 24.4 FO2745X1232 FO2745X1232T 100 50 889 35 " 24.3 FO2750X1235 FO2750X1235T 120 55 965 38 " 24.1 FO2755X1238 FO2755X1238T 140 60 1041 41 " 24.0 FO2760X1241 FO2760X1241T 140 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 20 813 32 1 or 3 Phase 10.9 FO2720X1232 FO2720X1232T 125 40 1448 57 " 10.9 FO2740X1257 FO2740X1257T 125 60 2083 82 " 10.9 FO2760X1282 FO2760X1282T 125 WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS 8 (1-800-492-8826)
FANGE HEATERS 10 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available Moisture resistant Explosion resistant D DIA. G A COD END H TAE 7 10-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY F DIA. E HOES ON A C.C. WATT DENSITY W/in. 2 FANGE 10 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 8 14 1/4 16 12 1 1 3/16 10 300 lb. 8 15 1/4 17 1/2 16 1 1/8 1 7/8 9 1/4 WITHOUT WITH NET WT. S (approx.) 100 660 26 1 or 3 Phase 64.3 FC36100X1426 --------------------------- 79 140 813 32 " 65.4 FC36140X1432 --------------------------- 82 160 889 35 " 65.8 FC36160X1435 --------------------------- 84 200 1067 42 " 64.3 FC36200X1442 --------------------------- 92 240 991 39 " 63.8 FC48240X1435 --------------------------- 95 280 1092 43 " 65.4 FC48280X1443 --------------------------- 110 300 1168 46 " 64.3 FC48300X1446 --------------------------- 125 320 1219 48 " 64.9 FC48320X1448 --------------------------- 125 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 100 660 26 1 or 3 Phase 64.3 FI36100X1426 --------------------------- 79 140 813 32 " 65.4 FI36140X1432 --------------------------- 83 160 889 35 " 65.8 FI36160X1435 --------------------------- 88 200 1067 42 " 64.3 FI36200X1442 --------------------------- 95 240 991 39 " 63.8 FI48240X1439 --------------------------- 110 300 1168 46 " 64.3 FI48300X1446 --------------------------- 118 320 1219 48 " 64.9 FI48320X1448 --------------------------- 126 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 100 1118 44 1 or 3 Phase 22.7 FO48100X1444 --------------------------- 84 120 1245 49 " 23.7 FO48120X1449 --------------------------- 88 140 1473 58 " 22.5 FO48140X1458 --------------------------- 92 160 1575 62 " 23.7 FO48160X1462 --------------------------- 92 180 1753 69 " 23.5 FO48180X1469 --------------------------- 92 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 70 1600 63 1 or 3 Phase 10.2 FO4870X1463 --------------------------- 90 80 1702 67 " 10.8 FO4880X1467 --------------------------- 100 100 2083 82 " 10.7 FO48100X1482 --------------------------- 100 WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS (1-800-492-8826) 9
FANGE HEATERS 12 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available Moisture resistant Explosion resistant G COD END H F DIA. E HOES ON A C.C. D DIA. A TAE 8 12-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY WATT DENSITY W/in. 2 FANGE 12 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 8 17 19 12 1 1 1/4 9 3/4 300 lb. 8 17 3/4 20 1/2 16 1 1/4 2 9 WITHOUT WITH NET WT. S (approx.) 150 711 28 1 or 3 Phase 63.4 FC48150X1628 --------------------------- 100 175 787 31 " 63.5 FC48175X1631 --------------------------- 100 200 838 33 " 66.3 FC48200X1633 --------------------------- 100 250 1016 40 " 63.7 FC48250X1640 --------------------------- 100 300 1168 46 " 63.8 FC48300X1646 --------------------------- 120 400 1219 48 " 64.5 FC60400X1648 --------------------------- 120 450 1346 53 " 64.2 FC60450X1653 --------------------------- 120 500 1448 57 " 65.3 FC60500X1657 --------------------------- 125 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 150 711 28 1 or 3 Phase 63.4 FI48150X1628 --------------------------- 100 175 787 31 " 63.5 FI48175X1631 --------------------------- 100 200 838 33 " 66.3 FI48200X1633 --------------------------- 100 250 1016 40 " 63.7 FI48250X1640 --------------------------- 100 300 1168 46 " 63.8 FI48300X1646 --------------------------- 120 400 1219 48 64.5 FI60400X1648 --------------------------- 120 500 1448 57 " 65.3 FI60500X1657 --------------------------- 125 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 150 1245 49 1 or 3 Phase 23.6 FO60150X1649 --------------------------- 125 200 1575 62 " 23.6 FO60200X1662 --------------------------- 125 250 1905 75 " 23.6 FO60250X1675 --------------------------- 125 300 2184 86 " 24.3 FO60300X1686 --------------------------- 125 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 100 1727 68 1 or 3 Phase 10.6 FO60100X1668 --------------------------- 125 150 2337 92 " 11.3 FO60150X1692 --------------------------- 125 WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS 10 (1-800-492-8826)
FANGE HEATERS 14 FANGE HEATERS Refer to PAGE 2 for the GENERA RECOMMENDATIONS es Available Moisture resistant Explosion resistant D DIA. G A COD END H TAE 9 14-3 Cold Section - 150 lb. Steel Flange IOWATTS IMMERSION ENGTH mm in. VOTAGES 208, 240 COPPER SHEATH - 65 WPSI (Approx.) - HIGH DENSITY F DIA. E HOES ON A C.C. WATT DENSITY W/in. 2 FANGE 14 FANGE RATING HEATER DIMENSION IN INCHES A C D E F G H 150 lb. 8 18 3/4 21 12 1 1/8 1 3/8 9 3/4 300 lb. 8 20 1/4 23 20 1 1/4 2 1/8 9 WITHOUT WITH NET WT. S (approx.) 250 864 34 1 or 3 Phase 63.6 FC60250X1834 --------------------------- 130 300 965 38 " 65.5 FC60300X1838 --------------------------- 150 350 1092 43 " 64.9 FC60350X1843 --------------------------- 150 400 1219 48 " 64.5 FC60400X1848 --------------------------- 150 500 1118 44 " 64.3 FC84500X1844 --------------------------- 170 600 1295 51 " 64.1 FC84600X1851 --------------------------- 170 650 1397 55 " 63.3 FC84650X1855 --------------------------- 170 700 1473 58 " 63.9 FC84700X1858 --------------------------- 170 INCOOY SHEATH - 65 WPSI (Approx.) - HIGH DENSITY 250 864 34 1 or 3 Phase 63.6 FI60250X1834 --------------------------- 130 300 965 38 " 65.5 FI60300X1838 --------------------------- 150 350 1092 43 " 64.9 FI60350X1843 --------------------------- 150 400 1219 48 " 64.5 FI60400X1848 --------------------------- 150 500 1118 44 " 64.3 FI84500X1844 --------------------------- 170 600 1295 51 " 64.1 FI84600X1851 --------------------------- 170 700 1473 58 " 63.9 FI84700X1858 --------------------------- 170 STEE SHEATH - 23 WPSI (Approx.) - MEDIUM DENSITY 150 889 35 1 or 3 Phase 26.2 FO84150X1835 --------------------------- 170 200 1143 45 " 25.0 FO84200X1845 --------------------------- 170 250 1321 52 " 26.1 FO84250X1852 --------------------------- 170 300 1575 62 " 25.3 FO84300X1862 --------------------------- 170 STEE SHEATH - 10 WPSI (Approx.) - OW DENSITY 100 1219 48 1 or 3 Phase 11.5 FO84100X1848 --------------------------- 140 150 1727 68 " 11.3 FO84150X1868 --------------------------- 180 WHEN ORDERING, PEASE SPECIFY: Quantity, catalogue number, voltage, phase, wattage, material to be heated, flowing or static mediums, types of controls to be applied, type of metal or alloy of the container, any extra features. CUSTOMERS MUST AWAYS ADVISE IF FANGE IMMERSION HEATERS ARE FOR STEAM PRESSURED APPICATIONS (1-800-492-8826) 11
FANGE HEATERS EXTRA FEATURES DESCRIPTION VOTAGE WATTCO flange heaters are custom-built and supplied with voltages up to 600V. WATTAGE ENGTH EXTRA HEAVY WA SHEATH Custom made heaters can be supplied with any requested wattage. WATTCO flange heaters are supplied with immersed lengths of a maximum of 180. When the immersed length exceeds 50, it is recommended to install an internal vessel support. Heavy wall sheath (0.049 or 0.065 thickness) is provided in: Incoloy Inconel Steel Stainless steel FANGE S AND RATINGS Refer to the Welding flanges section on page 13 and 14 PASSIVATION WEDED EEMENTS UIT-IN WE UIT-IN HIGH IMITS AND S UIT-IN THERMOCOUPES VENTED OR STITED HOUSINGS SPECIA TERMINA HOUSINGS Available Incoloy and stainless steel sheathed heaters are supplied with chemically passivated sheaths. Note: Chemically passivated sheaths are highly corrosion resistant in most applications. Passivation process is carried out through electropolishing. WATTCO stainless steel flange heaters can come with passivated wetted surfaces (Teflon on top of the sheath). WATTCO standard flange heaters are made of elements that are silver-brazed, Tig or welded to the flange. Heaters are supplied with welded elements for the following sheath material: Incoloy Stainless steel Steel Copper uilt-in thermostat wells can be installed upon request. When ordering, please provide length and internal diameter. For process temperature control, built-in high limits and thermostats can be installed upon request. Standard built-in thermostats: One-pole device of a maximum of 240V up to 30 amps. Thermocouples can be mounted to provide sheath limit protection or temperature control. Configured temperature control and power controls are available to meet the requirements of any application. Vented or stilted housings prevent the connection wire from overheating in many high temperature applications. Special terminal housings for all types of flange heaters can be made: Moisture resistant Explosion resistant When requesting an explosion-proof housing, please provide: Class Division or zone Group Temperature code for unsafe locations (Refer to Figures 1-4) MOISTURE RESISTANT FG. FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. NO. NO WITH 2 1/2" 1 4 3/4" 4 1/4" 8 1/2" 4 1/4" 3" 1 4 3/4" 4 1/4" 8 1/2" 4 1/4" 4" 1 5 1/8" 6" 8 1/2" 6" 5" 2 7" 9 1/4" 6" 2 7" 10 1/8" 8" 2 9" 12 1/8" 10" 2 9" 14 3/4" 12" 2 9" 16 3/4" 14" 2 9" 18 3/4" For S.I. conversion to metric multiply by 25.4 EXPOSION RESISTANT FG. FIG. NO. NO WITH 2 1/2" 3 5 3/4" 4" 9 1/4" 4" 3" 3 5 3/4" 4" 9 1/4" 4" 4" 3 6 1/8" 5 5/8" 9 1/4" 5 5/8" 5" 4 7 1/2" 7 1/2" 6" 4 7 1/2" 9" 8" 4 8 1/8" 11" 10" 4 10 1/8" 13 1/2" 12" 4 10 1/8" 15 1/2" 14" 4 10 1/8" 17 1/2" 12 (1-800-492-8826)
FANGE HEATERS WEDING FANGES / FORGED STEE ASTM A 105 CASS 150 FANGES CASS 150 FANGES Carbon steel to ASTM A 105. SA 105 flanges can be supplied upon request. Material of NPS 26 and up complies with ASTM A181 grades 1 and 2. Flanges are: furnished, faced, drilled, spot faced or back faced. Thread lengths: - ANSI for Pipe Threads - ANSI 2.1 (additional depth or height of facing is required to thread length) Note: Contact us at 1.800.492.8826 for pressure-temperature ratings CONSTRUCTION DIMENSIONS All dimensions are in inches and comply with ANSI 16.5 when applicable. NPS 22: interpolated. NPS 26 to NPS 42: same flange drilling dimensions as class 125 cast iron flanges. olt holes: 1/8 inch larger than bolt diameter. Flanges are indicated with shown dimensions. Dimensions shown match ANSI 36.10 inside diameter of a standard wall pipe. Thickness of two nuts is included in length of alloy steel stud bolts. Thickness of lap not included in length shown. For lapped to lapped dimension, additional thickness of both laps are required. For lapped to 1/16 inch raised face, additional thickness of one lap is required. For lapped to any other facing, combining facing and one lap will result in the separation of the flanges. R O WEDING NEC - FIG. 1 Y 1/16 Q Y Q R 1/16 O THREADED - FIG. 2 TAE 1 Class 150 Flanges NOMINA PIPE OUTSIDE DIAM. OF FANGE O THICNESS OF FANGE Q (min.) DIAM. OF RAISED FACE R DIAM. OF HU AT ASE X NO. OF OT HOES DIAM. OF OTS DIAM. OF OT CIRCE ENGTH OF OTS STUD MACHINE 1/2 3 1/2 7/16 1 3/8 1 3/16 4 1/2 2 3/8 2 1/4 3/4 1 7/8 5/8 5/8 3/4 3 7/8 1/2 1 11/16 1 1/2 4 1/2 2 3/4 2 1/4 2 2 1/16 5/8 5/8 1 4 1/4 9/16 2 1 15/16 4 1/2 3 1/8 2 1/2 3 2 2 3/16 11/16 11/16 1 1/4 4 5/8 5/8 2 1/2 2 5/16 4 1/2 3 1/2 2 1/2 3 2 1/4 2 1/4 13/16 13/16 1 1/2 5 11/16 2 7/8 2 9/16 4 1/2 3 7/8 2 3/4 3 1/4 2 1/4 2 7/16 7/8 7/8 2 6 3/4 3 5/8 3 7/16 4 5/8 4 3/4 3 3 1/2 2 3/4 2 1/2 1 1 2 1/2 7 7/8 4 1/8 3 9/16 4 5/8 5 1/2 3 1/4 3 3/4 3 2 3/4 1 1/8 1 1/8 3 7 1/2 15/16 5 4 1/4 4 5/8 6 3 1/2 4 3 2 3/4 1 3/16 1 3/16 3 1/2 8 1/2 15/16 5 1/2 4 13/16 8 5/8 7 3 1/2 4 3 2 13/16 1 1/4 1 1/4 4 9 15/16 6 3/16 5 5/16 8 5/8 7 1/2 3 1/2 4 3 3 1 5/16 1 5/16 5 10 15/16 7 5/16 6 7/16 8 3/4 8 1/2 3 3/4 4 1/4 3 1/4 3 1/2 1 7/16 1 7/16 6 11 1 8 1/2 7 9/16 8 3/4 9 1/2 3 3/4 4 1/4 3 1/4 3 1/2 1 9/16 1 9/16 8 13 1/2 1 1/8 10 5/8 9 11/16 8 3/4 11 3/4 4 4 1/2 3 1/2 4 1 3/4 1 3/4 10 16 1 3/16 12 3/4 12 12 7/8 14 1/4 4 1/2 5 3 3/4 4 1 15/16 1 15/16 12 19 1 1/4 15 14 3/8 12 7/8 17 4 1/2 5 4 4 1/2 2 3/16 2 3/16 14 21 1 3/8 16 1/4 15 3/4 12 1 18 3/4 5 5 1/2 4 1/4 5 2 1/4 3 1/8 16 23 1/2 1 7/16 18 1/2 18 16 1 21 1/4 5 1/4 5 3/4 4 1/2 5 2 1/2 3 7/16 18 25 1 9/16 21 19 7/8 16 1 1/8 22 3/4 5 3/4 6 1/4 4 3/4 5 1/2 2 11/16 3 13/16 20 27 1/2 1 11/16 23 22 20 1 1/8 25 6 6 1/2 5 1/4 5 11/16 2 7/8 4 1/16 22 29 1/2 1 13/16 25 1/4 24 20 1 1/4 27 1/4 6 1/2 7 5 1/2 5 7/8 3 1/8 4 1/4 24 32 1 7/8 27 1/4 26 1/8 20 1 1/4 29 1/2 6 3/4 7 1/4 5 3/4 6 3 1/4 4 3/8 26 34 1/4 2 29 1/4 28 1/2 24 1 1/4 31 3/4 7 6 5 3 3/8 28 36 1/2 2 1/16 31 1/4 30 3/4 28 1 1/4 34 7 6 5 1/16 3 7/16 30 38 3/4 2 1/8 33 3/4 32 3/4 28 1 1/4 36 7 1/4 6 1/4 5 1/8 3 1/2 32 41 3/4 2 1/4 35 3/4 35 28 1 1/2 38 1/2 8 6 3/4 5 1/4 3 5/8 34 43 3/4 2 5/16 37 3/4 37 32 1 1/2 40 1/2 8 7 5 5/16 3 11/16 36 46 2 3/8 40 1/4 39 1/4 32 1 1/2 42 3/4 8 1/4 7 5 3/8 3 3/4 42 53 2 5/8 47 46 36 1 1/2 49 1/2 8 3/4 7 1/2 5 3/8 4 1/16 RAISED FACE RING JOINT 1/16 RAISED FACE WEDING NEC Y ENGTH THRU HU SIP-ON, TH RD SOCET Y AP JOINT Y (1-800-492-8826) 13
FANGE HEATERS WEDING FANGES / FORGED STEE ASTM A 105 CASS 300 FANGES CASS 300 FANGES Carbon steel to ASTM A 105. SA 105 flanges can be supplied upon request. Material of NPS 26 and up complies with ASTM A181 grades 1 and 2. Flanges are: furnished, faced, drilled, spot faced or back faced. Thread lengths: - ANSI for Pipe Threads. - ANSI 2.1 (additional depth or height of facing is required to thread length). Note: Contact us at 1.800.492.8826 for pressure-temperature ratings CONSTRUCTION DIMENSIONS All dimensions are in inches and comply with ANSI 16.5 when applicable. NPS 22: interpolated. NPS 26 to NPS 42: same flange drilling dimensions as class 125 cast iron flanges. olt holes: 1/8 inch larger than bolt diameter. Flanges are indicated with shown dimensions. Dimensions shown match ANSI 36.10 inside diameter of a standard wall pipe. Thickness of two nuts is included in length of alloy steel stud bolts. Thickness of lap not included in length shown. For lapped to lapped dimension, additional thickness of both laps are required. For lapped to 1/16 inch raised face, additional thickness of one lap is required. For lapped to any other facing, combining facing and one lap will result in the separation of the flanges. R O WEDING NEC - FIG. 3 Y 1/16 Q Y Q R 1/16 O THREADED - FIG. 4 TAE 2 Class 300 Flanges NOMINA PIPE OUTSIDE DIAM. OF FANGE O THICNESS OF FANGE Q (min.) DIAM. OF RAISED FACE R DIAM. OF HU AT ASE X NO. OF OT HOES DIAM. OF OTS DIAM. OF OT CIRCE ENGTH OF OTS STUD MACHINE 1/2 3 3/4 9/16 1 3/8 1 1/2 4 1/2 2 5/8 2 1/2 3 2 2 1/16 7/8 7/8 3/4 4 5/8 5/8 1 11/16 1 7/8 4 5/8 3 1/4 2 3/4 3 1/4 2 1/2 2 1/4 1 1 1 4 7/8 11/16 2 2 1/8 4 5/8 3 1/2 3 3 1/2 2 1/2 2 7/16 1 1/16 1 1/16 1 1/4 5 1/4 3/4 2 1/2 2 1/2 4 5/8 3 7/8 3 3 1/2 2 3/4 2 9/16 1 1/16 1 1/16 1 1/2 6 1/8 13/16 2 7/8 2 3/4 4 3/4 4 1/2 3 1/2 4 3 2 11/16 1 3/16 1 3/16 2 6 1/2 7/8 3 5/8 3 5/16 8 5/8 5 3 1/4 4 3 2 3/4 1 5/16 1 5/16 2 1/2 7 1/2 1 4 1/8 3 15/16 8 3/4 5 7/8 3 3/4 4 1/2 3 1/4 3 1 1/2 1 1/2 3 8 1/4 1 1/8 5 4 5/8 8 3/4 6 5/8 4 4 3/4 3 1/2 3 1/8 1 11/16 1 11/16 3 1/2 9 1 3/16 5 1/2 5 1/4 8 3/4 7 1/4 4 1/4 5 3 3/4 3 3/16 1 3/4 1 3/4 4 10 1 1/4 6 3/16 5 3/4 8 3/4 7 7/8 4 1/4 5 3 3/4 3 3/8 1 7/8 1 7/8 5 11 1 3/8 7 5/16 7 8 3/4 9 1/4 4 1/2 5 1/4 4 3 7/8 2 2 6 12 1/2 1 7/16 8 1/2 8 1/8 12 3/4 10 5/8 4 3/4 5 1/2 4 1/4 3 7/8 2 1/16 2 1/16 8 15 1 5/8 10 5/8 10 1/4 12 7/8 13 5 1/4 6 4 3/4 4 3/8 2 7/16 2 7/16 10 17 1/2 1 7/8 12 3/4 12 5/8 16 1 15 1/4 6 6 3/4 5 1/4 4 5/8 2 5/8 3 3/4 12 20 1/2 2 15 14 3/4 16 1 1/8 17 3/4 6 1/2 7 1/4 5 3/4 5 1/8 2 7/8 4 14 23 2 1/8 16 1/4 16 3/4 20 1 1/8 20 1/4 6 3/4 7 1/2 6 5 5/8 3 4 3/8 16 25 1/2 2 1/4 18 1/2 19 20 1 1/4 22 1/2 7 1/4 8 6 1/2 5 3/4 3 1/4 4 3/4 18 28 2 3/8 21 21 24 1 1/4 24 3/4 7 1/2 8 1/4 6 3/4 6 1/4 3 1/2 5 1/8 20 30 1/2 2 1/2 23 23 1/8 24 1 1/4 27 8 8 3/4 7 6 3/8 3 3/4 5 1/2 22 33 2 5/8 25 1/4 25 1/4 24 1 1/2 29 1/4 8 3/4 9 3/4 7 1/2 6 1/2 4 5 3/4 24 36 2 3/4 27 1/4 27 5/8 24 1 1/2 32 9 10 7 3/4 6 5/8 4 3/16 6 26 38 1/4 3 1/8 29 1/2 28 3/8 28 1 5/8 34 1/2 10 11 8 3/4 7 1/4 7 1/4 28 40 3/4 3 3/8 31 1/2 30 1/2 28 1 5/8 37 10 1/2 11 1/2 9 1/4 7 3/4 7 3/4 30 43 3 5/8 33 3/4 32 9/16 28 1 3/4 39 1/4 11 1/4 12 1/4 10 8 1/4 8 1/4 32 45 1/4 3 7/8 36 34 11/16 28 1 7/8 41 1/2 12 13 1/4 10 1/2 8 3/4 8 3/4 34 47 1/2 4 38 36 7/8 28 1 7/8 43 1/2 12 1/4 13 1/2 10 3/4 9 1/8 9 1/8 36 50 4 1/8 40 1/4 39 32 2 46 12 3/4 14 11 1/4 9 1/2 9 1/2 1/16 RAISED FACE RING JOINT 1/16 RAISED FACE WEDING NEC Y ENGTH THRU HU SIP-ON, TH RD SOCET Y AP JOINT Y 14 (1-800-492-8826)
OIER FANGES OVERVIEW WATTCO square or round flange heaters are the perfect energy efficient solution for heating liquids in open tanks and low-pressure vessels. Suitable for constrained areas, square and round flanges are made of compact elements that are easily installed by tightening a series of bolts. Changing the assembly is simple: Disconnect the power Unbolt the flange Replace it with another heater ENEFITS Energy efficient road variety of sizes for different applications Compact Superior seal between flanges Moisture and contaminant resistant Easy to install Easy to maintain Designed and built for safety EY FEATURES Replacement oiler Flange Heaters TYPE F Square flange Round flange SEECTING REPACEMENT OIER FANGE HEATERS WITH SQUARE FANGES WATTCO FANGE HEATER WITH SQUARE FANGES This section will help you select the most suitable WATTCO replacement boiler flange heater with square flanges that meets the requirements of your application. Please call us at 1.800.4WATTCO (1.800.492.8826) for further assistance. CAUTION ow water levels in the boiler or excessive scale build-up on the heating elements cause most boiler heater failures and both have to be taken into account should several heaters fail simultaneously. It is recommended to contact a water treatment specialist in your area to examine or clean your system before installing any replacement parts. 2 1/2 SQUARE FANGE WHEN ORDERING, PEASE SPECIFY: quantity catalogue number flange size and material voltage/wattage phase steam* or water boiler replacement description of the heater if no catalogue or part number matched your unit APPICATIONS Please consider the following factors in order to select the proper flange heater: Water oiler equipment Open storage tanks containing: Degreasing solvents Fuel oils Heat-transfer fluids Caustic solutions 2 1/2 SQUARE STEE FANGE (CUSTOM-DESIGNED) The following types of heater configurations are available upon request: WHEN ORDERING, PEASE SPECIFY: type 1, 2 or 3 dimension voltage / wattage phase any additional drawings if available For other custom units, please specify: application flange size, dimensions, and material sheath material and diameter number of elements quantity options bolt pattern, if not standard no-heat section below the flange immersed length See figures below. Available replacements: 3 5/8 x 9 5/8 FANGE 5 1/2 SQUARE FANGE 4 1/2 SQUARE FANGE 6 3/4 SQUARE FANGE 1 1/2 1 1/2 1 5/8 * WARNING: When placing an order, please specify if you are requesting a replacement unit/part for a steam application. Special recommendations will be given. (1-800-492-8826) 15
OIER FANGES SEECTING REPACEMENT OIER HEATERS WITH ROUND FANGES WATTCO FANGE HEATER WITH ROUND FANGES This section will help you select the most suitable WATTCO replacement boiler flange heater with round flanges that meets the requirements of your application. Please call us at 1.800.4WATTCO (1.800.492.8826) for further assistance. CAUTION ow water levels in the boiler or excessive scale build-up on the heating elements cause most boiler heater failures and both have to be taken into account should several heaters fail simultaneously. It is recommended to contact a water treatment specialist in your area to examine or clean your system before installing any replacement parts. TAE 1 6 - SPECIA FANGE - OIERS W STD. VOTAGES CAT. NO. WT. - S (G) 15 208, 240, 416, FI9116415X10 31 (14) 15 " FI9116815X10 31 (14) 30 " FI9117130X10 40 (18) 30 " FI9118130X10 40 (18) 30 " FI9118230X10 40 (18) 36 " FI9118236X10 40 (18) 37.5 " FI9118237X10 40 (18) 45 " FI9118245X10 44 (20) 45 " FI9118345X10 44 (20) 45 " FI9118445X10 44 (20) 60 " FI9118560X10 48 (22) 60 " FI9118660X10 48 (22) 60 " FI9118760X10 48 (22) 72 " FI9118772X10 53 (24) 75 " FI9118775X10 53 (24) 75 " FI9118875X10 53 (24) 75 " FI9118975X10 53 (24) 90 " FI9118990X10 59 (27) 90 " FI9119090X10 59 (27) 90 " FI9119190X10 59 (27) 108 " FI9120108X10 66 (30) 112.5 " FI9120112X10 66 (30) 125 " FI9120125X10 70 (32) 135 " FI9120135X10 70 (32) 145 " FI9120145X10 70 (32) 150 " FI9120150X10 70 (32) 187.5 " FI9120187X10 79 (36) 225 " FI9120225X10 79 (36) TAE 2 6-150. FANGE - OIERS W STD. VOTAGES CAT. NO. WT. - S (G) 15 208, 240, 416, FI9216415X10 35 (16) 30 " FI9216830X10 44 (20) 30 " FI9217130X10 44 (20) 38 " FI9218138X10 44 (20) 45 " FI9218245X10 48 (22) 45 " FI9218245X10 48 (22) 60 " FI9218260X10 53 (24) 75 " FI9218275X10 57 (26) 75 " FI9218375X10 57 (26) 90 " FI9218490X10 66 (30) 90 " FI9218590X10 66 (30) 100 " FI9218100X10 73 (33) 135 " FI9218135X10 73 (33) WHEN ORDERING, PEASE SPECIFY: quantity catalogue number flange size and material voltage/wattage phase steam* or water boiler replacement description of the heater if no catalogue or part number matched your unit drawings * WARNING: When placing an order, please specify if you are requesting a replacement unit/part for a steam application. Special recommendations will be given. 16 (1-800-492-8826)
OIER FANGES SEECTING REPACEMENT OIER HEATERS WITH ROUND FANGES WATTCO FANGE HEATER WITH ROUND FANGES This section will help you select the most suitable WATTCO replacement boiler flange heater with round flanges that meets the requirements of your application. Please call us at 1.800.4WATTCO (1.800.492.8826) for further assistance. CAUTION ow water levels in the boiler or excessive scale build-up on the heating elements cause most boiler heater failures and both have to be taken into account should several heaters fail simultaneously. It is recommended to contact a water treatment specialist in your area to examine or clean your system before installing any replacement parts. TAE 3 6-300. FANGE - OIERS W STD. VOTAGES CAT. NO. WT. WHEN ORDERING, PEASE SPECIFY: quantity, catalogue number, flange size and material, voltage/wattage, phase, steam* or water boiler replacement, description of the heater if no catalogue or part number matched your unit. - S (G) 116.7 208, 240, 416, FI9236116X10 60 (30) 150 " FI9236150X10 70 (32) 175.1 " FI9236175X10 75 (34) TAE 4 8-150. FANGE - OIERS W STD. VOTAGES CAT. NO. WT. - S (G) 36 208, 240, 416, FI9236036X12 79 (36) (38) 45 " FI9236045X12 84 (40) 72 " FI9236072X12 88 (42) 90 " FI9236090X12 92 (42) 108 " FI9236108X12 92 (45) 135 " FI9236135X12 99 (45) 144 " FI9236144X12 99 (48) 180 " FI9236180X12 106 (48) 180 " FI9237180X12 106 (51) 216 " FI9236216X12 112 (54) 225 " FI9236225X12 119 (63) 270 " FI9236270X12 139 (63) 270 " FI9236270X12 139 (33) CUSTOM HEATERS WITH ROUND FANGES WHEN ORDERING A CUSTOM ROUND FANGE OIER REPACEMENT, PEASE SPECIFY: type A,, C, D dimensions, voltage/wattage, phase, number of elements, number of circuits FOR OTHER CUSTOM UNITS, PEASE SPECIFY: application flange size, dimensions, and material sheath material and diameter quantity options bolt pattern, if not standard no-heat section below the flange immersed length 5 6 TYPE A 3/4 DIA. - 4 HOES EQUI-SPACED ON A 4 3/4 DIA. OT CIRCE TYPE 3/4 DIA. - 4 HOES EQUI-SPACED ON A 6 DIA. OT CIRCE C 9/32 DIA. - 8 HOES EQUI-SPACED ON A 4 1/2 DIA. OT CIRCE TYPE C 3/8 DIA. - 6 HOES EQUI-SPACED ON A 4 3/4 DIA. OT CIRCE TYPE D 6 7 1/2 * WARNING: When placing an order, please specify if you are requesting a replacement unit/part for a steam application. Special recommendations will be given. (1-800-492-8826) 17
FANGE HEATERS TERMINA HOUSINGS 3 inch ANSI flanged heater NEMA 1 3 inch ANSI flanged heater NEMA 4 3 inch ANSI flanged heater NEMA 7 4 inch ANSI flanged heater NEMA 1 4 inch ANSI flanged heater NEMA 4 4 inch ANSI flanged NEMA 7 5 inch ANSI flanged heater NEMA 1 5 inch ANSI flanged heater NEMA 4 5 inch ANSI flanged NEMA 7 * WARNING: When placing an order, please specify if you are requesting a replacement unit/part for a steam application. Special recommendations will be given. 18 (1-800-492-8826)
FANGE HEATERS TERMINA HOUSINGS 6 inch ANSI flanged heater NEMA 1 6 inch ANSI flanged heater NEMA 4 6 inch ANSI flanged NEMA 7 8 inch ANSI flanged heater NEMA 1 8 inch ANSI flanged heater NEMA 4 8 inch ANSI flanged NEMA 7 * WARNING: When placing an order, please specify if you are requesting a replacement unit/part for a steam application. Special recommendations will be given. (1-800-492-8826) 19