LAVA DESIGN INFRARED HEATING A work of art that emits heat.

LAVA DESIGN INFRARED HEATING A work of art that emits heat. www.etherma.com

THE FUTURE OF HEATING IS ALL ELECTRIC.

OUR MODELS AT A GLANCE LAVA BASIC-DM For wall and ceiling mounting. Page 8 LAVA -LED Accessories LED lighting for LAVA BASIC-DM. Page 9 LAVA FRAME For flush mounting in the ceiling and wall. Page 10 LAVA DESK 120 Under the desk. Page 11 LAVA STEEL 2.0 The entry-level model. Page 12f. LAVA GLAS 2.0 Noble glass look. Page 12f. LAVA CERAMIC 2.0 Timeless appearance. Page 12f. LAVA DYL 2.0 Individual design. Page 14 LAVA -CRYSTAL Accessories Swarovski crystals as finishing. Page 15 LAVA BATH 2.0 Infrared heating with towel holder. Page 16 LAVA GLAS 2.0 - PLUS For the extra power. Page 17 3

24-26 C 19,5-20 C 22 C 22 C 19-19,5 C 30 C 19 C 18 C KONVEKTIONSWÄRME CONVECTION INFRAROTWÄRME INFRARED HEAT INFRARED WARMTH - HOW IT WORKS LAVA design infrared heating is based on the principle of solar radiation. The infrared heat emitted is absorbed by thermal mass (the ceiling, walls, floor, furniture and people) where it is stored and gradually released back into the room. This homogeneous heating of the room results in a pleasant cosy environment where you feel relaxed. As you are warmed directly by the infrared, the room air temperature can be reduced by up to 2-3 C with the same comfort - and each degree Celsius less saves around 6-7% of energy. As a positive side-effect, these warm walls provide better insulation and prevent condensation and in the worst cases mould. Walls that absorb infrared radiation are drier as they absorb less atmospheric moisture, resulting in a more comfortable environment with a constant humidity of 45% to 55% - an absolute benefit for comfort. Allergy sufferers also benefit from infrared heat. Standard heaters warm the air to create a feeling of warmth. The warmer air rises to the ceiling where it is cooled again and sinks back down to the ground, wasting valuable energy and prolonging the warm-up time. These convection currents carry dust particles and allergens and dry out the air even further. This is not the case with infrared heating as objects are heated directly and convection currents are virtually non-existent. 4

THE HEATING (R)EVOLUTION Lower heat requirements in well-insulated buildings, rapidly increasing gas and oil prices and the ongoing development of photovoltaic technology are making infrared heating systems a practical alternative. The precisely-timed electronic regulation for individual rooms offers a comfortable and energy-efficient heating method. With infrared heating systems, the heat is generated quickly at the touch of a button and is produced where it is needed, in the room itself, with no energy loss. Electric heating systems are more costeffective to buy and install and do not generate any maintenance costs. They enable innovative and independent heating systems to be combined with one s own power generation system, such as photovoltaic cells. This reduces dependence on oil and gas and offers protection against their future price increases. Historically electric heating has been considered as expensive to run, However, recent technological developments, precisely-ti- med regulation and optimised insulation of outer walls and windows mean that this is no longer the case. On the contrary, if you take into account the true life cost of a heating system (capital investment, installation, operating and on-going maintenance costs) over a 20-year period, LAVA infrared heating turns out to be one of the most convenient and cost-effective heating systems. Even the power suppliers have changed their thinking over the last few years and are now increasingly turning to renewable power. Numerous interesting offers from energy suppliers are enabling customers to help shape the direction of future energy policy. Those who opt for an electric heating system are no longer using up precious resources as it was often claimed. In fact, electric infrared heating is now recommended by some power suppliers as a cleaner, more environmentally-friendly and costefficient source of heating. 5

AREAS OF APPLICATION FOR LAVA Infrared radiant heat is a fast, healthy and independent form of heating for the following areas of application: PRIMARY HEATING Ideal as a comprehensive solution for wellinsulated buildings, low energy homes and passive energy buildings. EXTRA HEATING Can be used in addition to existing heating systems. Suitable for renovations, extensions and loft conversions, particularly in bathrooms, relaxation areas, bedrooms, living rooms and conservatories. During the transition periods between the warm and cold months of the year, bathroom heating may only be required for one to two hours in the morning and evening. Switching on the entire heating system for this is both inefficient and expensive. LAVA design infrared heaters, by contrast, enable targeted and precisely-timed heating at only a fraction of the standard heating costs. LOCALISED EXTRA HEATING Ideal for when additional heat is required during a certain time, for example at individual work stations or massage and treatment tables. 6

THE BENEFITS OF THE LAVA DESIGN INFRARED HEATING HEALTHY Comfortable warmth with low-temperature-radiant heat with no electromagnetic field. EFFICIENT Heat is generated where it is needed, 100% loss-free. Pinpoint accuracy thanks to individual room controls. ECONOMICAL No maintenance costs, operating cost savings thanks to increased heat sensitivity. SUSATINABLE Clean power from renewables. Self-sufficiency if combined with own power generation. ELEGANT Exceptional design or simply in the background. Allows individal layout. SIMPLE Uncomplicated, rapid assembly - horizontal, vertical and overhead installation. QUICK Warmth at the push of a button, high radiation area, heat storage up to an hour. CHEAP Lower purchase, installation and maintenance costs than alternative heating systems. 7

LAVA BASIC-DM TECHNICAL DATA > Voltage: 230 V > Output: 350, 500, 750, 1000, 1500 W > Surface temperature: max. 120 C > Surface: Structured surfaces Steel housing, white RAL 9016 > Device/Installation depth: 22/52 mm > IP Rating: IP 21 > Connection cable: 1 m, 3 x 1.5 mm², no plug > Warranty: 5 years > Certification: TÜV The LAVA BASIC-DM is suitable for heating from the ceiling as well as from the wall, e.g. as an inconspicuous heater for living rooms, offices, bathrooms, schools, containers. The LAVA BASIC-DM is a 22 mm flat infrared heater that impresses with its uniform infrared heat and aesthetics. Mounted on the ceiling, in suspended ceilings or on the wall, the heaters are ideally suited for full area heating or zone heating. When installed in suspended ceilings, the heater is fully integrated into the ceiling. Ceiling mounting allows optimal use of the area and avoids any potential damage from bumping the panel. Available in white (RAL 9016) and 5 power outputs. BENEFITS OF THIS PRODUCT + + Suitable for ceiling and wall mounting + + 350, 750, 1500 W suitable for grid ceilings (625 x 625 mm) + + Ideal for the ceiling due to a lightweight construction + + High radiant heating effect + + Maximum radiation to the front due to the optimally insulated rear + + Maintenance free and magnetic field free 62 cm 62 cm 62 cm 62 cm 124,5 cm 124,5 cm 160 cm 124,5 cm 90 cm 62cm 350 W 500 W 750 W 1000 W 1500 W 8

TECHNICAL DATA Efficient LED lighting as an accessory. LAVA -LED > Colour temperature: 2700 K / 4000 K > Luminous flux: 3000 lm/lfm > Output: 24 W/m > Voltage: 24 V/DC > IP Rating: IP 20 > Beam angle: 120 > Service life: 60,000 h BENEFITS OF THIS PRODUCT + + Low consumption due to LED technology + + 2 light colours (warm white/daylight) + + Straightforward installation + + Maintenance-free + + Long service life due to the high temperature resistance + + Optional dimming module & hand transmitter LAVA -LED is an accessory for the LAVA BASIC-DM infrared heater which can be used to light rooms, workplaces, but can also serve as an effect lighting. Consisting of two white aluminium profiles and an opal Plexiglass cover for ideal light diffusion, the LAVA -LED is attached to the long sides of the infrared heater. The LAVA -LED is controlled independently of the infrared heater. With the optional dimming module, the LED light bars can be dimmed either by means of a wired wall switch or with a hand transmitter. 9

LAVA FRAME TECHNICAL DATA > Voltage: 230 V > Output: 350, 500, 750, 1000 W > Surface temperature: max. 120 C > Surface: Structured surfaces > Frame: Steel housing, white RAL 9016 > Device depth: 22 mm > Installation depth: 75 mm > IP Rating: IP 21 > Connection cable: 1 m, 3 x 1.5 mm², no plug > Warranty: 5 years LAVA FRAME is a built-in infrared heater that can be flush-mounted in the ceiling or wall due to the installation frame, thus creating a harmonious room appearance. LAVA FRAME is ideally suited for installation in dry construction and concrete. This means that the LAVA infrared heater blends into the architecture of the room and becomes virtually invisible. Suitable as full area heating system or just as a zone heating solution to address cold-spots. This not only saves the heating costs, but also ensures a pleasant, healthy indoor climate. BENEFITS OF THIS PRODUCT + + Suitable for wall and ceiling installation + + Mounting frame with Easy-Click + + Flush-mounted installation + + Simple installation + + Large infrared emitting surface + + High radiant heating effect + + Maintenance free and magnetic field free 62 cm 62 cm 62 cm 62cm 62 cm 90 cm 124,5 cm 160 cm 350 W 500 W 750 W 1000 W Dimensions without frame 10

TECHNICAL DATA LAVA DESK 120 > Voltage: 230 V > Output: 120 W > Surface temperature: max. 70 C > Surface: Smooth surface > Frame: Steel housing, white RAL 9016 > Device/Installation depth: 15 mm > IP Rating: IP 21 > Connection cable: 2 m incl. on/off switch, with plug > Certification: EC compliant BENEFITS OF THIS PRODUCT + + Undertable & wall mounting + + Infrared radiant heat + + Maintenance-free + + Without magnetic field LAVA DESK provides perfect warmth at your desk - be it in the workplace, in the kids bedroom, or for a warm spot for your four-legged friend. Simple installation with only 4 screws allows the provision of trouble-free infrared heating beneath the dining table or on walls, and gives targeted warmth. With a height of only 15 mm, the unit is all but invisible under the table, and takes up very little space. 70 cm 28 cm 120 W 11

LAVA 2.0 DESIGN INFRARED HEATING Get Plug & Play ready with 2.0. The LAVA 2.0 design infrared heaters are particularly efficient and energy-saving. The 6 mm thick ESG toughened safety glass or the 6 mm special ceramic as well as 2 temperature limiters in all panels guarantee safety in use at all times, the EMIMAX technology turns the surfaces into a very good radiation emitter. In conjunction with the even heat distribution on the surface, the optimally insulated rear guarantees a high radiation efficiency and thus the maximum infrared heat radiation into the room - the heat works exactly where it is needed. The frameless construction creates the modern design. Three surfaces (STEEL / GLASS / CERAMIC) and up to 6 power outputs are available. The practical Plug & Play box on the rear of all LAVA 2.0 models makes it easy to attach the desired controller. Controls include manual (on the device), wireless and hard-wired options. BENEFITS OF THIS PRODUCT + + Highest radiation efficiency due to maximum forward radiation EMIMAX technology homogeneous surface temperature large surface optimally insulated rear (max. 40 C) + + Frameless Infinity design + + Plug & Play connection system for easy individual control + + Highest safety against breakage and overheating + + No service or maintenance required + + Without magnetic field TECHNICAL DATA > Voltage: 230 V > Output: 250 1000 W > Surface temperature: max. 95 C > Surface: Steel sheet or ESG safety glass 6 mm or 6 mm special ceramic > Device/Installation depth: 26/57 mm (Steel) or 30/61 mm (Glass & Ceramic) > IP Rating: IP X4 > IEC Protection Class: I > Connection cable: 1m, with plug > Installation: horizontally or vertically > Warranty: 5 years > Certification: TÜV 12

LAVA 2.0 in three different surfaces: LAVA STEEL 2.0 LAVA GLAS 2.0 LAVA CERAMIC 2.0 White Mirror White green Pure white Black and red available on request. Calacatta Dimensions STEEL Dimensions GLAS 50 cm Dimensions CERAMIC 50 cm 50 cm 90 cm 130 cm 160 cm 50 cm 90 cm 130 cm 130 cm 160 cm 160 cm 50 cm 90 cm 130 cm 160 cm 250 W 500 W 750 W 1000 W 250 W 500 W 600 W 750 W 800 W 1000 W 250 W 500 W 750 W 1000 W 13

DESIGN IT YOURSELF NOW. LAVA GLAS 2.0 DESIGN YOUR LAVA TECHNICAL DATA > Voltage: 230 V > Output: 180 700 W > Surface temperature: max. 70 C > Surface: 6 mm ESG Safety glass > Device/Installation depth: 30/61 mm > IP Rating: IP X4 > IEC Protection Class: I > Connection cable: 1 m, with plug > Warranty: 5 years BENEFITS OF THIS PRODUCT LAVA DYL offers the possibility to individually design your LAVA GLAS 2.0 infrared heating. We print your desired theme - whether a holiday photo or company logo, so that the infrared heating fits perfectly into your environment. The LAVA DYL can be mounted vertically and horizontally on the wall. All LAVA DYL are supplied with a power cord and an ON/OFF switch, are suitable for wall mounting and are Plug & Play ready. + + Your LAVA entirely the way you imagine it (e.g. logo, photo). + + Plug & Play connection system for easy individual control + + Service and maintenance free + + Without magnetic field ETHERMA HINT: Go to www.etherma.com for tips on how to design your image file to ensure perfect printing results. Should you have any questions, please contact: marketing@etherma.com. 50 cm 90 cm 160 cm 130 cm 180 W 350 W 500 W 700 W 14

Precious SWAROVSKI crystals for your LAVA. LAVA -CRYSTAL Exclusive and unique - an absolute design highlight. Refine your LAVA GLAS 2.0 infrared heating with sparkling SWAROVSKI EL- EMENTS and make it a real eye-catcher. Three brilliant designs bring any room to shine and set accents to the interior design. Crystal 01 Crystal 02 Crystal 03 ETHERMA HINT: As design highlight on all LAVA GLAS 2.0 additionally available and to be ordered separately. 15

LAVA BATH 2.0 TECHNICAL DATA > Voltage: 230 V > Output: 350 700 W > Surface temperature: max. 70 C > Surface: Steel sheet or ESG safety glass 6 mm > Device/Installation depth: Steel sheet 26/57 mm or glass 30/61 mm > IP Rating: IP X4 > Connection cable: 1 m, with plug > Warranty: 5 years BENEFITS OF THIS PRODUCT The LAVA BATH 2.0 is the perfect heat source for your bathroom. The infrared radiant heat is generated by a special heating element with no magnetic field - once switched on, the surface is heated to a constant 70 C giving snug warmth within the shortest time and with the towel rail, it also provides cosy warm towels. + + High radiant heating effect + + Frameless Infinity design + + Plug & Play connection system for easy individual control + + Various thermostat options as accessories + + One towel holder LAVA Halti included and one more is available as accessory. + + Easy installation - vertical wall mounting only + + Maintenance free and magnetic field free 50 cm 50 cm Various thermostats are optionally available. In addition, another LAVA Halti towel rail can be attached to the device. 90 cm 130 cm 130 cm 160 cm 160 cm 350 W 400 W 500 W 600 W 700 W 16

TECHNICAL DATA LAVA GLAS 2.0 - PLUS > Voltage: 230 V > Output: 1000 1500 W > Surface temperature: max. 95 C > Surface: 6 mm safety glass, white > Device/Installation depth: 90 mm > IP Rating: IP 24 > IEC Protection Class: I > Connection cable: 1m, with plug > Installation: Horizontal > Warranty: 5 years BENEFITS OF THIS PRODUCT + + Powerful + + Saves space + + Large infrared emitting surface + + Maintenance free and magnetic field free + + Plug & Play connection system for easy individual control + + Only for horizontal installation on walls + + Straightforward installation The LAVA GLAS 2.0 - PLUS is a designed radiant heating system with the plus on performance. This powerful heating device saves space and yet still produces comfortable infrared radiant heat with additional space heating. The heating unit can be mounted horizontally on the wall and is suitable for large rooms as well as anywhere where extra heat is required. The LAVA GLAS 2.0 - PLUS stands out due to its elegant design and fast heat delivery. Its Plug & Play control system allow the simple, fast connection of an integrated control, a radio receiver or a wired room thermostat. The LAVA GLAS 2.0 - PLUS stores heat for up to 1h. 105 cm 150 cm 1000 W 1500 W 17

VERSION 1 RADIO CONTROL BASIC CONTROL LAVA -F: SIMPLER WITH RADIO Radio-controlled thermostats avoid complex elevation and plaster work for cable routing and allow easy installation of heaters. The LAVA -F radio receiver can be quickly fitted to all LAVA 2.0 using the connection system. The receiver is controlled by the ET-14A radio thermostat (sold separately) which can control up to 16 LAVA -F radio receivers. The ET-14A has a programmable week program, frost protection function, manual mode and ON/OFF function. LAVA : PLUG & PLAY BASIC MODULE All LAVA infrared heaters are supplied without control system, but with a plug lead and ON/OFF switch. They are, therefore, ideal for new construction and anywhere where wired room thermostats are used. The Plug & Play connection system (IP65) allows direct connection to a wired room thermostat, easy integration with a radio receiver LAVA -F or direct control of the device with the LAVA -R thermostat or Timer LAVA -T. VERSION 2 WIRED WIRED ROOM THERMOSTATS Ideal for new buildings and renovation, for example when old night storage heaters, which were controlled by thermostat, are replaced. etouch eco etwist etouch basic LAVA 2.0 PLUG & PLAY CONTROL SYSTEM The control you always wanted. Modern, precise control is the key to saving the operating costs and avoiding the waste of the valuable energy. The various types of the LAVA design infrared heaters in combination with an appropriate thermostat provides the ideal solution for every individual need. Due to the new Plug & Play connection system, you can tailor your LAVA design infrared heaters to your individual needs at any time. For instance, you can upgrade the standard model at a later stage with a thermostat or a radio receiver. 18

VERSION 3 ON THE DEVICE LAVA -R: THE INTEGRATED THERMOSTAT All LAVA 2.0 infrared heaters can be fitted with a thermostat which has been developed specifically for infrared heaters. The thermostat controls the room temperature and optimises the surface temperature of the LAVA. Furthermore, the surface temperature in children s rooms and bathrooms, for example, can be limited to 60 C with a switch. The adjustable temperature range is from 5 to 35 C. The LAVA -R thermostat can be easily fitted to all LAVA 2.0 units using the connection system. In combination with the enexho home automation system (more information on page 90), you can also conveniently control your LAVA design infrared heater using a smartphone, tablet or PC when you are out and about. Plug & Play box LAVA -T THE CONVENIENT TIMER All LAVA 2.0 infrared heaters can be fitted with a timer which is specially developed for the temporary operation. By pressing the timer the device heats for 2 hours with maximum power and then switches off automatically. The timer can be switched off early at any time by pressing the button again. The LAVA -T can be easily fitted to all LAVA 2.0 units using the connection system. On the device Type P&P-Box LAVA -R Wired LAVA -T Radio control ET-14A LAVA -F ET-111A (thermostat) (receiver) (receiver) etouch eco etwist etouch basic LAVA BASIC-DM LAVA FRAME LAVA DESK 120 LAVA STEEL 2.0 V LAVA GLAS 2.0 V LAVA CERAMIC 2.0 V LAVA DYL 2.0 V LAVA BATH 2.0 V LAVA GLAS 2.0-PLUS V V: Pre-installed : Accessories 19

THE PERFECT COMPLEMENT. The combination of underfloor and infrared heating makes every house a cosy warm home. ETHERMA has the right heating mat for every type of flooring, whether tile, laminate or parquet. The netted heating mats can be custom-made to ensure an easy and fast installation in architecturally challenging spaces. All statements without guarantee. Changes, errors and misprints reserved. ETHERMA Elektrowärme GmbH Landesstraße 16 A-5302 Henndorf T +43 (0) 6214 / 76 77 F +43 (0) 6214 / 76 66 office@etherma.com www.etherma.com ARC THERMAL PRODUCTS UK Distributor Buckinghamshire, HP5 3QW T +44 (0) 1923 889481 sales@arc-ers.co.uk arcthermalproducts.co.uk