Features Two different models for sampling fixed volumes of 3 cc or 8 cc per sample cycle Can handle line pressures from vacuum up to 200 psi (13.8 bar) in most applications Rugged 316 stainless steel construction Batch or composite sampling ATEX compliant ISOLOK SERIES SAA Automatic Sampler Automatic Sampler for Liquids and Slurries Description The ISOLOK SAA provides accurate samples of liquids and slurries such as waste acid, resin bead slurry, bauxite mud and raw municipal sludge. The ISOLOK SAA operates when compressed air forces the plunger into the process line to capture a fixed volume of material. Compressed air then acts on the opposite side of the piston to retract the plunger to a position which allows the sample to drop by gravity into a container. ISOLOK series SAA Sampler Options Port closures Line adapters Several types of containers Sampler enclosures (with or without heater) Sample heating or refrigeration The operator is isolated from the process at all times by the sampler's seal design, and the sample captured in the container is "locked out" from external influences. Metal parts are made of 316 stainless steel; other alloys are available. Process contact seals are filled-teflon for chemical applications or wear-resistant elastomers for abrasive slurries. Modular components allow selection of various bodies and plungers to meet the process application. Optional materials of construction and seal choices www.sentry-equip.com 19.1.6 Rev. 7 02/14
sampling process Plunger extended; process isolated Plunger retracted; sample isolated and locked ISOLOK SAA TECHNICAL DATA Sample Volume per Cycle 3 cc or 8 cc Maximum Particle Size 3 mm (3 cc) or 7 mm (8 cc) Basic Electrical Requirements (with Sentry controller) 115 VAC, single phase, 50/60 Hz Line Mounting Options MNPS thread, tri-clamp, instrument hub, ANSI flange Compressed Air Requirements 2 SCFM @ 90 psi (.05 m³/min @ 6.2 bar) Materials of Construction Plunger Seals Cylinder Seals Net Weight, not including controller or accessories SPECIFICATIONS Kalrez is a registered trademark of E. I. Du Pont de Nemours and Company. Halar is a registered trademark of Ausimont, U.S.A. Inc. 316 stainless steel; other materials available TFE, polyurethane, EPDM rubber, Kalrez or custom European Authorized Rep: OBELIS Bd. General Wahis 53-1030 Brussels Belgium Halar, TFE, or custom 8 10 lb (3.5 4.5 kg) II 2GD TX It is solely the responsibility of the end-user, through its own analysis and testing, to select products and materials suitable for their specific application requirements, ensure they are properly installed, safely applied, properly maintained, and limit their use to their intended purpose. Improper selection, installation, or use may result in personal injury or property damage. SENTRY EQUIPMENT CORP 966 Blue Ribbon Circle North Oconomowoc, WI 53066 USA Tel: 262-567-7256 Fax: 262-567-4523 E-mail: sales@sentry-equip.com Website: www.sentry-equip.com For further information, contact: SENTRY EQUIPMENT (SG) PTE. LTD. (Co. Regn./GST: 201412829H) 701, Sims Drive, #08-01, LHK Building, Singapore 387383. Tel: +65 6458 9920 website: www.sentry.com.sg e-mail: sales@sentry.com.sg Sentry Equipment Corp 2006 19.1.6 Rev. 7 02/14
Features Two different models for sampling fixed volumes of 10 cc or 25 cc per sample cycle Can handle line pressures from vacuum up to 300 psi (20.7 bar) in most applications Rugged 316 stainless steel construction Batch or composite sampling ATEX compliant ISOLOK SERIES SAB Automatic Sampler Automatic Large Capacity Sampler for Liquids and Slurries Description The ISOLOK SAB provides accurate samples of liquids and slurries such as waste acid, resin bead slurry, bauxite mud and raw municipal sludge. The ISOLOK SAB operates when compressed air forces the plunger into the process line to capture a fixed volume of material. Compressed air then acts on the opposite side of the piston to retract the plunger to a position which allows the sample to drop by gravity into a container. ISOLOK series SAB Sampler Options Port closures Line adapters Several types of containers Sampler enclosures (with orwithout heater) Sample heating or refrigeration The operator is isolated from the process at all times by the sampler's seal design, and the sample captured in the container is "locked out" from external influences. Metal parts are made of 316 stainless steel; other alloys are available. Process contact seals are filled- Teflon for chemical applications or wear-resistant elastomers for abrasive slurries. Modular components allow selection of various bodies and plungers to meet the process application. Optional materials of construction and seal choices www.sentry-equip.com 19.1.7 Rev. 5 02/14
sampling process Plunger extended; process isolated Plunger retracted; sample isolated and locked ISOLOK SAB TECHNICAL DATA SPECIFICATIONS Sample Volume per Cycle Maximum Particle Size Basic Electrical Requirements (with Sentry controller) Line Mounting Options Compressed Air Requirements Materials of Construction Plunger Seals Cylinder Seals Net Weight, not including controller or accessories Kalrez is a registered trademark of E. I. Du Pont de Nemours and Company. Halar is a registered trademark of Ausimont, U.S.A. Inc. Model SAB-25: 25 cc; Model SAB-10: 10 cc 0.375" (9 mm) 115 VAC, single phase, 50/60 Hz MNPS thread, tri-clamp, instrument hub, ANSI flange 60 psig (4.14 barg) minimum 316 stainless steel; other materials available TFE, polyurethane, EPDM rubber, Kalrez or custom European Authorized Rep: OBELIS Bd. General Wahis 53-1030 Brussels Belgium Halar, TFE, or custom 28 32 lb (12.7 14.5 kg) II 2GD TX It is solely the responsibility of the end-user, through its own analysis and testing, to select products and materials suitable for their specific application requirements, ensure they are properly installed, safely applied, properly maintained, and limit their use to their intended purpose. Improper selection, installation, or use may result in personal injury or property damage. SENTRY EQUIPMENT CORP 966 Blue Ribbon Circle North Oconomowoc, WI 53066 USA Tel: 262-567-7256 Fax: 262-567-4523 E-mail: sales@sentry-equip.com Website: www.sentry-equip.com For further information, contact: SENTRY EQUIPMENT (SG) PTE. LTD. (Co. Regn./GST: 201412829H) 701, Sims Drive, #08-01, LHK Building, Singapore 387383. Tel: +65 6458 9920 website: www.sentry.com.sg e-mail: sales@sentry.com.sg Sentry Equipment Corp 2006 19.1.7 Rev. 5 02/14
Features Fixed-volume samplers available in three sizes: 50 cc, 120 cc, or 200 cc per sample cycle Can handle line pressures from vacuum up to 300 psi (21 bar) in most applications Rugged stainless steel construction Batch or composite sampling ATEX compliant Options Port closures Line adapters Several types of containers ISOLOK SERIES SAG Automatic Sampler Automatic Extra-Large Capacity Samplers for Liquids and Slurries Sampler enclosures (with or without heater) Sample heating or refrigeration Optional materials of construction and seal choices Description The ISOLOK SAG has the capacity to collect large quantity samples with just a few cycles over a short time period. It provides accurate samples of liquids and slurries such as radioactive waste, waste acid, resin bead slurry, bauxite mud and raw municipal sludge. The ISOLOK SAG operates when compressed air forces the plunger into the process line to capture a fixed volume of material. Compressed air then acts on the opposite side of the piston to retract the plunger to a position which allows the sample to drop into a container. The operator is isolated from the process at all times by the sampler's seal design, and the sample captured in the container is "locked out" from external influences. Metal parts are made of 316 stainless steel; other alloys are available. Process contact seals are filled-teflon for chemical applications or wear-resistant elastomers for abrasive slurries. Modular components allow selection of various bodies and plungers to meet the process application. ISOLOK series SAG Sampler www.sentry-equip.com 19.1.16 Rev. 5 02/14
sampling process plunger extended; process isolated plunger retracted; sample isolated and locked ISOLOK SAG TECHNICAL DATA 16 11 16" (42.4 cm) 9" (22.9 cm) 3 9 16" (9 cm) 1/8 ¼ NPT NPT Purge Port/Vent 1/8 NPT Line Adapter Head Drain Body Vent Sample Discharge Port 2 3/8" (6 cm) 4 ¼" (10.8 cm) Momentary Plunger Extension SPECIFICATIONS Sampe Volume / Cycle 50 cc 120 cc 200 cc Maximum Particle Size ¼" (6.3 mm) 5/8" (15.9 mm) 7/8" (22.2 mm) Line Mounting Options MNPS thread, tri-clamp, instrument hub, ANSI flange Compressed Air Requirements 2 SCFM @ 90 psi (.05 m³/min @ 6.2 bar) Materials of Construction 316 stainless steel; other materials available Plunger Seals TFE, polyurethane, EPDM, Kalrez or custom Cylinder Seals Halar, TFE, or custom Net Weight, not including controller or accessories 35 39 lb (15.8 17.7 kg) Kalrez and Teflon are registered trademarks of E. I. Du Pont de Nemours and Company. Halar is a registered trademark of Ausimont, U.S.A. Inc. European Authorized Rep: OBELIS Bd. General Wahis 53-1030 Brussels Belgium II 2GD TX It is solely the responsibility of the end-user, through its own analysis and testing, to select products and materials suitable for their specific application requirements, ensure they are properly installed, safely applied, properly maintained, and limit their use to their intended purpose. Improper selection, installation, or use may result in personal injury or property damage. SENTRY EQUIPMENT CORP 966 Blue Ribbon Circle North Oconomowoc, WI 53066 USA Tel: 262-567-7256 Fax: 262-567-4523 E-mail: sales@sentry-equip.com Website: www.sentry-equip.com For further information, contact: SENTRY EQUIPMENT (SG) PTE. LTD. (Co. Regn./GST: 201412829H) 701, Sims Drive, #08-01, LHK Building, Singapore 387383. Tel: +65 6458 9920 website: www.sentry.com.sg e-mail: sales@sentry.com.sg Sentry Equipment Corp 2009 19.1.16 Rev. 5 02/14