Testing laboratory locations: 1. Testing Laboratory in Prague (0100) Prosecká 811/76a, 190 00 Praha 9 2. Testing Laboratory in České Budějovice (0200) 3. Testing Laboratory in Plzeň (0300) Zahradní 15, 326 00 Plzeň Slovany 4. Testing Laboratory in Teplice (0400) Tolstého 447, 415 03 Teplice 5. Testing Laboratory in Předměřice n. L. (0500) Průmyslová 283, 503 02 Předměřice nad Labem 6. Testing Laboratory in Brno (0600) Hněvkovského 77, 617 00 Brno The Laboratory is qualified to update standards identifying the test procedures. The Laboratory is qualified to carry out independent sampling. Tests: 1. Testing Laboratory in Prague 1.1 Acoustics 1.1.1 reserved 1.2 Concrete, admixtures and fibres for concrete 1.2.1* Slump test ČSN EN 12350-2 Fresh concrete 1.2.2* VeBe test ČSN EN 12 350-3 Fresh concrete 1.2.3* Flow table test ČSN EN 12 350-5 Fresh concrete 1.2.4* mass per unit volume ČSN EN 12350-6 Fresh concrete 1.2.5* air content ČSN EN 12 350-7 pressure methods Fresh concrete 1.2.6 concrete frost resistance ČSN 73 1322 1.2.7 cement concrete surface resistance to water and chemical de-icing ČSN 73 1326, A, C method agents 1.2.8* Testing of shapes and dimensions ČSN EN 12390-1 1.2.9* compressive strength of concrete, including the manufacture and treatment of test specimens ČSN EN 12390-2 ČSN EN 12390-3 ČSN EN 12504-1 1.2.10 compressive ČSN EN 12390-3 strength of test specimens Page 1 of 91
1.2.11 flexural strength of test specimens ČSN EN 12390-5 1.2.12 the indirect tensile strength of test ČSN EN 12390-6 specimens 1.2.13 density of hardened concrete ČSN EN 12390-7 1.2.14 depth of penetration of water under ČSN EN 12390-8 pressure 1.2.15 static modulus of elasticity in ČSN ISO 1920-10 compression 1.2.16* Test of compressive strength ČSN EN 12504-1 1.2.17* rebound by hardness drop ČSN EN 12504-2 tester 1.2.18* Test of compressive strength by hardness testing methods (Schmidt N. L.) ČSN 73 1373 1.2.19 setting time ČSN EN 480-2 Concrete and mortar additives 1.2.20 bleeding of Concrete and mortar ČSN EN 480-4 concrete additives 1.2.21 capillary Concrete and mortar ČSN EN 480-5 absorption additives 1.2.22 solids Concrete and mortar ČSN EN 480-8 content additives 1.2.23 air void Concrete and mortar characteristics in hardened ČSN EN 480-11 additives concrete 1.2.24 1.2.25 1.2.26 flexural tensile strength (limit of proportionality, residual strength) dry bulk density mechanical properties (compressive strength, flexural strength, concentric compressive strength) 1.3 Small concrete products ČSN EN 14651+A1 ČSN EN 678 ČSN EN 679 Metallic fibre-reinforced concrete Autoclaved concrete Aerated concrete 1.3.1* dimensions ČSN EN 1338 Annex C Page 2 of 91
1.3.2* dimensions ČSN EN 1339 Annex C 1.3.3* dimensions ČSN EN 1340 Annex C 1.3.4 total water absorption ČSN EN 1338 Annex E 1.3.5 total water absorption ČSN EN 1339 Annex E 1.3.6 total water absorption ČSN EN 1340 Annex E 1.3.7 the indirect tensile strength ČSN EN 1338 Annex F 1.3.8 flexural strength and fracture load ČSN EN 1339 Annex F 1.3.9 bending strength ČSN EN 1340 Annex F 1.3.10 abrasiveness Bohme ČSN EN 1338 Annex H 1.3.11 resistance to freezing/thawing ČSN EN 1338 Annex D 1.3.12 resistance to ČSN EN 1339 Annex D freezing/thawing 1.3.13 resistance to ČSN EN 1340 Annex D freezing/thawing 1.4 Concrete building components and structures 1.4.1* shapes and dimensions, appearance ČSN 73 0212-5 1.4.2* dimensions ČSN EN 991 1.4.3 1.4.4 1.4.5 1.4.6 1.4.7 1.4.8 Tests of strength and load bearing capacity Tests of strength and load bearing capacity shear load capacity mechanical durability and stability - by test impact strength mass of components Building components Lightweight and aerated concrete components ČSN EN 1916 only Annex C Concrete pipes ČSN EN 1917 except Annex C, D ČSN EN 1168+A3 Annex J ČSN EN 1520 ed. 2 Annex B ČSN 73 2035 ČSN 73 2045 Concrete manholes Hollow core slabs Reinforced components of lightweight concrete Building components Building components 1.5 Timber, timber components, timber based and fibre-cement products 1.5.1* Static loading tests ČSN EN 380 Timber structures Page 3 of 91
1.5.2 loadbearing capacity and stiffness ČSN EN 594 Timber structures 1.5.3 bearing capacity and deformation ČSN EN 595 Timber structures behaviour 1.5.4 Soft body impact test ČSN EN 596 Timber structures 1.5.5 physical and mechanical properties ČSN EN 408+A1 Structural and glued timber 1.5.6 Visual determination of Coniferous sawn timber for ČSN 73 2824-1 grading characteristics structural elements 1.5.7 Shear test ČSN EN 14080 Annex D Glued timber 1.5.8* Testing of dimensions and geometrical characteristics ČSN EN 12467 ed. 2 p. 7.2 Fibre-cement flat sheets 1.5.9* moisture content ČSN EN 13183-2 Structural timber 1.5.10 moisture content ČSN EN 322 Wood-based panels 1.5.11 hard body Cement-bonded ČSN EN 1128 impact resistance particleboards 1.5.12 Testing of joints of timber Fixtures for timber ČSN EN 1380 structures structures 1.5.13 Testing of joints of timber Fixtures for timber ČSN EN 1075 structures structures 1.5.14 Testing of joints of timber Fixtures for timber ČSN EN 1381 structures structures 1.5.15 Testing of joints of timber Fixtures for timber ČSN EN 1382 structures structures 1.5.16 Testing of joints of timber Fixtures for timber ČSN EN 1383 structures structures 1.5.17 Testing of joints of timber Fixtures for timber ČSN EN 26891 structures structures 1.6 Physical factors 1.6.1 reserved 1.7 Glass grids, geotextiles and geotextile-related products 1.7.1 tensile strength and elongation of mesh ČSN EN 13496 Glass fibre mesh 1.8 Games, toys and school supplies, playgrounds, matches and lighters 1.8.1 reserved 1.9 Materials, products and waterproofing systems 1.9.1 length, width and straightness ČSN EN 1848-1 Asphalt sheets Page 4 of 91
1.9.2 length, width and straightness ČSN EN 1848-2 Plastic and rubber sheets 1.9.3 thickness ČSN EN 1849-1 Asphalt sheets 1.9.4 mass per unit area ČSN EN 1849-1 Asphalt sheets 1.9.5 thickness ČSN EN 1849-2 Plastic and rubber belts 1.9.6 mass per Plastic and rubber belts and ČSN EN 1849-2 unit area sheets 1.9.7 visible defects ČSN EN 1850-1 Asphalt sheets 1.9.8 visible Plastic and rubber belts and ČSN EN 1850-2 defects sheets 1.9.9 flow resistance ČSN EN 1110 Asphalt sheets 1.9.10 tensile properties ČSN EN 12311-1 Asphalt sheets 1.9.11 tensile Plastic and rubber belts and ČSN EN 12311-2 properties sheets 1.9.12 change in volume due to water/swelling/ ZP No. 12-97 Bentonite-based materials 1.9.13* tensile Waterproofing of concrete ČSN EN 13596 adhesion strength bridge decks 1.9.14 Bitumen, plastic and rubber ČSN EN 1928 watertightness belts and sheets 1.9.15 Bituminous polymermodified cements ČSN EN 15820 watertightness 1.9.16 water Bitumen, plastic and rubber ČSN EN 1931 vapour permeability belts and sheets 1.9.17 water vapour transmission properties ČSN EN ISO 12572 Hygroscopic, nonhygroscopic building materials, sheathed products 1.9.18 dimensional ČSN EN 1107-1 Asphalt sheets 1.9.19 1.9.20 1.9.21 1.9.22 1.9.23 stability dimensional stability resistance to long term exposure to elevated temperature resistance to blistering geometrical properties water absorption ČSN EN 1107-2 ČSN EN 1296 ČSN EN 544 ed. 2 p. 6.4.5 ČSN EN 544 ed. 2 p. 6.3 ČSN EN 544 ed. 2 p. 6.4.3 Plastic and rubber belts, sheets Bitumen, plastic and rubber belts and sheets Bitumen shingles Bitumen shingles Bitumen shingles Page 5 of 91
1.9.24 1.9.25 1.9.26 1.9.27 1.9.28 1.9.29 1.9.30 1.9.31 1.9.32 1.9.33 1.9.34 1.9.35 1.9.36 mass per unit area of bitumen resistance to delamination resistance to wind load watertightness resistance to artificial ageing (fluorescence UV lamps) resistance to artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water resistance to dynamic indentation resistance to static indentation accelerated ageing by heat accelerated ageing by hot water the effects liquid chemicals, including water peel resistance of joints (fissility of sheets) resistance to tearing (nail shank) ČSN EN 544 ed. 2 p. 6.2 EOTA TR 004 EOTA TR 005 ČSN EN 14891 method A.7 EOTA TR 010 ČSN EN 1297 EOTA TR 006 EOTA TR 007 except 5.2.5 c) EOTA TR 011 EOTA TR 012 ČSN EN 1847 ČSN EN 12316-1 ČSN EN 12310-1 1.10 Household chemicals cleaning and washing agents 1.10.1 reserved 1.11 Chemical analyses of silicate and building products 1.11.1 reserved 1.12 Stone, aggregates, inactive concrete admixtures, soils 1.12.1 resistance to freezing and thawing ČSN EN 1367-1 Bitumen shingles Cast roof waterproofing assemblies Cast roof waterproofing assemblies Liquid-applied water impermeable products used under ceramic tiling Cast roof waterproofing assemblies, etc. Bitumen, plastic and rubber belts and sheets Cast roof waterproofing assemblies, etc. Cast roof waterproofing assemblies, etc. Cast roof waterproofing assemblies, etc. Cast roof waterproofing assemblies Plastic and rubber belts and sheets Asphalt sheets Asphalt sheets Page 6 of 91
1.12.2 1.12.3 1.12.4 1.12.5 1.12.6 1.12.7 1.12.8 particle size distribution Sieving analysis particle shape - Shape index percentage of crushed and broken surfaces in coarse aggregate particles resistance to fragmentation loose bulk density and voids the water content by drying in a ventilated oven particle density and water absorption ČSN EN 933-1 ČSN EN 933-4 ČSN EN 933-5 ČSN EN 1097-2 ČSN EN 1097-3 ČSN EN 1097-5 ČSN EN 1097-6 1.12.9 Magnesium sulfate test ČSN EN 1367-2 1.12.10 density and water absorption ČSN EN 14617-1 1.13 Anchoring elements, including rail fasteners 1.13.1 reserved 1.14 Metallic materials and parts in construction Artificial stone 1.14.1* Performance of tensile tests ČSN EN ISO 6892-1 Metallic products 1.14.2 Performance of tensile tests ČSN EN ISO 15630-1 p. 5 Metallic products 1.14.3 Performance of tensile tests 1.14.4 Performance of tensile tests ČSN EN ISO 17660-1 p. 14.2 ČSN EN ISO 17660-2 p. 14.2 Metallic products Metallic products 1.14.5 Bend test ČSN EN ISO 7438 p. 4.1. Metallic products 1.14.6 Bend test 1.14.7 Bend test 1.14.8* 1.14.9 shape and dimensional accuracy of wrought products angle accuracy ČSN EN ISO 17660-1 p. 14.4 ČSN EN ISO 17660-2 p. 14.4 ČSN EN ISO 15630-1 p. 10, 11 ČSN EN 14195 Metallic products Metallic products Metallic products Metallic products Page 7 of 91
1.14.10 Performance of fatigue tests ČSN EN ISO 15630-1 p. 8 Metallic products 1.14.11* the quality of metal coating microscopic test 1.14.12 Shear test 1.14.13 Shear test 1.14.14 Shear test ČSN EN ISO 1463 ČSN EN ISO 17660-1 p. 14.3 ČSN EN ISO 17660-2 p. 14.3 ČSN EN 10080 Annex B.3, method 1 Metallic products Metallic products Metallic products Truss beams of concrete reinforcing steel 1.14.15 Salt spray test ČSN EN ISO 9227 p. 5.2 Metallic products 1.14.16 dimensions and limit deviations of organic coats ČSN EN 10245-1 Metallic products 1.15 Chimneys, chimney sheaths and flues, refractory materials and products, ceramic raw materials 1.15.1 reserved 1.16 Light industry products 1.16.1 reserved 1.17 Mortars, mortar mixtures, renovation materials, screeds 1.17.1 Frost resistance test ČSN 72 2452 Masonry mortars 1.17.2 1.17.3 1.17.4 1.17.5 1.17.6 1.17.7 1.17.8 consistence of fresh mortar by flow table consistence of fresh mortar by plunger penetration density of fresh mortar air content of fresh mortar workable life and correction time of fresh mortar dry bulk density of hardened mortar compressive strength of mortar ČSN EN 1015-3 ČSN EN 1015-4 ČSN EN 1015-6 ČSN EN 1015-7 ČSN EN 1015-9 ČSN EN 1015-10 ČSN EN 1015-11 Fresh mortar Fresh mortar Fresh mortar Fresh mortar Fresh mortar Dry mortar Dry hardened mortar 1.17.9 Test of compressive strength ČSN EN 13892-2 Screed materials Page 8 of 91
1.17.10 flexural strength of mortar ČSN EN 1015-11 Dry hardened mortar 1.17.11 Test of flexural strength ČSN EN 13892-2 Screed materials 1.17.12* adhesion ČSN EN 1015-12 Dry hardened mortar 1.17.13 adhesion of cementitious adhesives ČSN EN 1348 Mortars and adhesives 1.17.14* adhesion ČSN EN 13892-8 Screed materials 1.17.15 1.17.16 water absorption coefficient due to capillary action of hardened mortar water vapour permeability of surface finish of building structures ČSN EN 1015-18 ČSN EN 1015-19 Mortars Mortars 1.17.17 slip ČSN EN 1308 Mortars and adhesives 1.17.18 shear adhesion strength of dispersion adhesives ČSN EN 1324 Mortars and adhesives 1.17.19 open time ČSN EN 1346 Mortars and adhesives 1.17.20 1.17.21 shear adhesion strength of reaction resin adhesives abrasion resistance (Böhme) ČSN EN 12003 ČSN EN 13892-3 1.17.22 wear resistance by BCA method ČSN EN 13892-4 1.17.23 surface hardness ČSN EN 13892-6 1.17.24 dimensional ČSN EN 13872 variations 1.17.25 resistance of renovation plasters to salt WTA 2-9-04/D p. 6.3.10 bleeding, ČSN EN 445 p. 4.3, 4.4, 4.5, 1.17.26* volume changes, fluidity and 4.6 compressive strength 1.17.27 linear shrinkage ČSN EN 12617-1 Mortars and adhesives Screed materials Screed materials Screed materials Screed materials Renovation plasters Injection mortars Renovation materials Page 9 of 91
1.17.28 1.17.29 1.17.30 1.17.31 1.17.32 1.17.33* 1.17.34 thermal compatibility Freeze-thaw cycling with de-icing salt immersion shrinkage and expansion compressive strength of repair mortar resistance to capillary absorption resistance to carbonation depth carbonation depth abrasion resistance ČSN EN 13687-1 ČSN EN 12617-4 p. 6 ČSN EN 12190 ČSN EN 13057 ČSN EN 13295 ČSN EN 14630 ČSN EN ISO 5470-1 Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials 1.17.35 Pull-out test ČSN EN 1881 Renovation materials 1.17.36 1.17.37 1.17.38 1.17.39 Measurement of bond strength by pull-off modulus of elasticity in compression carbon dioxide permeability method A resistance to severe chemical attack method without pressure ČSN EN 1542 ČSN EN 13412 ČSN EN 1062-6 p. 8.1 ČSN EN 13529 1.18 Tanks, reservoirs, septic tanks, water treatment plants 1.18.1 reserved 1.19 Water, aqueous extracts, waste, sludge 1.19.1 reserved 1.20 Draining elements 1.20.1 Load test ČSN EN 1433 p. 9.1 1.20.2 1.20.3 dimensions and shape resistance to frost and chemical de-icing agents ČSN EN 1433 p. 9.3 ČSN EN 1433 Annex C Renovation materials Renovation materials Renovation materials Renovation materials Drainage channels for vehicular and pedestrian areas Drainage channels for vehicular and pedestrian areas Drainage channels for vehicular and pedestrian areas Page 10 of 91
1.20.4 1.20.5 dimensions, shape physicomechanical characteristics ČSN EN 124 except p. 8.4.7 ČSN EN 1433 1.21 Doors and windows, roof lights, hardware 1.21.1 air permeability of windows and doors ČSN EN 1026 1.21.2 Air permeability test of gates ČSN EN 12427 Gates 1.21.3 1.21.4 1.21.5 1.21.6 1.21.7 1.21.8 1.21.9 1.21.10 1.21.11 1.21.12 1.21.13 Watertightness test of ČSN EN 1027 windows and doors Test of window and door ČSN EN 12211 resistance to wind load Test of gate resistance to ČSN EN 12444 wind load the strength of welded corners of PVC-U ČSN EN 514 profiles for the manufacture of windows and doors thermal transmittance of windows and doors - by test - by calculation thermal transmittance of window and door frames - by test - by calculation thermal transmittance of roof lights - by test - by calculation gate resistance to water ČSN EN 12489 penetration window ČSN EN 12046-1 operating force door ČSN EN 12046-2 operating force the resistance to soft and heavy ČSN EN 949 body impact for doors ČSN EN ISO 12567-1 ČSN EN ISO 10077-1 p. 5 ČSN EN 12412-2 ČSN EN ISO 10077-2 p. 4, Annex C ČSN EN ISO 12567-2 ČSN EN 1873 Annex D Gully tops and manhole tops Drainage channels for vehicular and pedestrian areas Windows, doors Windows, doors Windows, doors Gates PVC-U profiles Windows, doors Window and door frames Roof lights, roof windows Gates Windows Doors Doors Page 11 of 91
1.21.14 1.21.15 1.21.16 1.21.17 1.21.18 1.21.19 the resistance to soft and heavy body impact for windows the resistance of doors to static torsion the resistance of windows to static torsion resistance of doors to racking resistance of windows to racking resistance of door leaves to hard body impact ČSN EN 13049 ČSN EN 948 ČSN EN 14609 ČSN EN 947 ČSN EN 14608 ČSN EN 950 Windows Doors Windows Doors Windows Door leaves 1.22 Gasolines, diesel oil, biofuels, oils, combustible and other liquids, lubricants 1.22.1 reserved 1.23 Plastics and composites 1.23.1 1.23.2 1.23.3 1.23.4 1.23.5 1.23.6 1.23.7 1.23.8 1.23.9 1.23.10 resistance to artificial ageing fluorescence UV lamps water absorption of plastics tensile properties tensile properties tensile properties compressive properties flexural properties the effects of immersion in liquid chemicals (including water) linear dimensions mass per unit volume ČSN EN ISO 4892-3 ČSN EN ISO 62 ČSN EN ISO 527-1 ČSN EN ISO 527-2 ČSN EN ISO 527-3 ČSN EN ISO 604 ČSN EN ISO 178 Plastics, rubbers, bitumen Plastics Plastics Plastics Plastics ČSN EN ISO 175, p. 5.4, 5.6 Plastics ČSN EN ISO 1923 ČSN EN ISO 845 Thermoplastics, thermosets and thermotropic polymers on the basis of liquid crystals Thermoplastics and thermosets Cellular plastics and rubber Cellular plastics and rubbers Page 12 of 91
1.23.11 1.23.12 1.23.13 1.23.14 1.23.15 1.23.16 thickness, width and length mass per unit area flexural properties resistance to compression the resistance to impact of main profiles by falling mass Shore hardness ČSN EN ISO 12017, p. 6.2, 6.3 ČSN EN ISO 12017 ČSN EN ISO 12017 ČSN EN ISO 3386-1 ČSN EN 477 ČSN EN ISO 868 Plastics (e.g. PMMA) Plastics (e.g. PMMA) Plastics (e.g. PMMA) Flexible cellular polymers (low density) Unplasticised polyvinyl chloride (PVC-U) profiles Plastics 1.24 Construction cements, fly ash, slags, stabilization of soils, bitumens 1.24.1 1.24.2 1.24.3 normal density and setting time of cement volume stability of cement the strength of cement ČSN EN 196-3+A1 p. 1-6 ČSN EN 196-3+A1 p. 1-4, 7 ČSN EN 196-1 1.25 Products and systems for prestressing of structures 1.25.1 reserved Cement, masonry cement Cement, masonry cement Cement, masonry cement 1.26 Gypsum and gypsum products, rock gypsum, anhydride, MgO based panels 1.26.1 1.26.2 flexural strength compressive strength ČSN EN 13279-2 ČSN EN 13279-2 1.26.3 adhesion ČSN EN 13963 ed. 2 1.26.4 adhesion ČSN EN 13963 1.26.5 setting time ČSN EN 13963 Gypsum binders and gypsum plasters Gypsum binders and gypsum plasters Jointing materials for gypsum boards Jointing materials for gypsum plasterboards Jointing materials for gypsum plasterboards 1.26.6 setting time ČSN EN 13963 ed. 2 Jointing materials 1.26.7 total water absorption ČSN EN 520+A1 p. 5.9.2 1.26.8 width ČSN EN 13950 Plasterboards Gypsum board thermal/acoustic insulation composite panels Page 13 of 91
1.26.9 thickness ČSN EN 13950 1.26.10 adhesion ČSN EN 13950 1.26.11 width ČSN EN 13950 ed. 2 1.26.12 thickness ČSN EN 13950 ed. 2 1.26.13 adhesion ČSN EN 13950 ed. 2 1.27 Construction and sanitary ceramics 1.27.1 reserved 1.28 Machinery, building and bridge bearings, elevators 1.28.1 reserved Gypsum board thermal/acoustic insulation composite panels Gypsum board thermal/acoustic insulation composite panels Gypsum thermal/acoustic insulation composite panels Gypsum thermal/acoustic insulation composite panels Gypsum thermal/acoustic insulation composite panels 1.29 Cements, adhesives, jointing materials, paints and coatings, surface finishes 1.29.1* adhesion ČSN 73 2577 Surface finish 1.29.2* watertightness ČSN 73 2578 Surface finish 1.29.3 resistance to ČSN 73 2579 frost Surface finish water 1.29.4 vapour transmission properties ČSN 73 2580 Surface finish 1.29.5 resistance to ČSN 73 2581 rapid temperature changes Surface finish 1.29.6 resistance to ČSN 73 2582 abrasion Surface finish 1.29.7 resistance to ČSN EN ISO 2812-1 liquids Surface finish 1.29.8 resistance to ČSN EN ISO 2812-4 liquids Surface finish 1.29.9 Pull-off test for adhesion ČSN EN ISO 4624 Surface finish 1.29.10 water vapour transmission rate ČSN EN ISO 7783 Surface finish 1.29.11 water permeability ČSN EN 1062-1 p. 5.6 Surface finish 1.29.12 water permeability ČSN EN 1062-3 Surface finish 1.29.13 Drop weight test ČSN EN ISO 6272-1 Surface finish Page 14 of 91
1.29.14* Cross-cut test ČSN EN ISO 2409 Surface finish 1.29.15* thickness ČSN EN ISO 2808 Surface finish 1.29.16 resistance to ČSN EN ISO 6270-1 humidity Surface finish 1.29.17 Assessment of degree of blistering ČSN EN ISO 4628-2 Surface finish 1.29.18 Assessment of degree of rusting ČSN EN ISO 4628-3 Surface finish 1.29.19 Assessment of degree of cracking ČSN EN ISO 4628-4 Surface finish 1.29.20 Assessment of degree of flaking ČSN EN ISO 4628-5 Surface finish 1.29.21 Assessment of degree of delamination and corrosion ČSN EN ISO 4628-8 Surface finish around a scribe 1.29.22 abrasion resistance - TABER- ZP No. 14-98 Surface finish ABRASER 1.29.23 abrasion resistance - TABER- ISO 7784-1 Surface finish ABRASER 1.29.24 abrasion resistance - TABER- ISO 7784-2 Surface finish ABRASER 1.29.25 colour ČSN EN ISO 3668 Surface finish specular 1.29.26* gloss ČSN EN ISO 2813 Surface finish resistance to 1.29.27 artificial ageing UV lamps ČSN EN 927-6 Surface finish and water 1.29.28 nonvolatile-matter content ČSN EN ISO 3251 Surface finish 1.29.29 elastic recovery ČSN EN ISO 7389 Sealants 1.29.30 resistance to ČSN EN ISO 7390 flow Sealants 1.29.31 adhesion and cohesion ČSN EN ISO 9046 Sealants 1.29.32 volume changes ČSN EN ISO 10563 Sealants 1.29.33 adhesion and cohesion at maintained extension after immersion in water ČSN EN ISO 10590 Sealants Page 15 of 91
1.29.34 adhesion and cohesion properties after ČSN EN ISO 10591 Sealants immersion in water 1.29.35 tensile properties ČSN EN ISO 8339 p. 8.2 Sealants 1.29.36 tensile properties at maintained extension ČSN EN ISO 8340 Sealants 1.29.37 resistance to ČSN EN ISO 11432 compression Sealants 1.29.38 chemical resistance ČSN EN 12808-1 Grouts for tiles 1.29.39 flexural and compressive strength ČSN EN 12808-3 Grouts for tiles 1.29.40 shrinkage ČSN EN 12808-4 Grouts for tiles 1.29.41 water absorption ČSN EN 12808-5 Grouts for tiles 1.29.42 ageing resistance exposure to offshore and related environments ČSN ISO 20340 Annex A Surface finish 1.30 Thermal insulation materials and products, thermal tests 1.30.1 1.30.2 1.30.3* tensile strength parallel to faces setting of blown insulation length and width ČSN EN 1608 ČSN EN 15101-1 Annex B, method B.2 ČSN EN 822 1.30.4* thickness ČSN EN 823 1.30.5 Pressure test ČSN EN 826 1.30.6 1.30.7 1.30.8 1.30.9 shear strength in axial direction shear strength in axial direction tensile strength perpendicular to faces dimensional stability under specified temperature and humidity conditions ČSN EN 253+A1 p. 5.4.1 ČSN EN 15632-4 p. 6.2 ČSN EN 1607 ČSN EN 1604 Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Page 16 of 91
1.30.10 1.30.11 1.30.12 1.30.13 1.30.14 dimensional stability at constant laboratory conditions water absorption by partial immersion long term water absorption by immersion elongation at break the content of pores and air voids ČSN EN 1603 ČSN EN 1609 ČSN EN 12087 ČSN EN 253+A1 p. 5.2.2 ČSN EN 253+A1 p. 5.3.2 1.30.15 Measurement of diameter ČSN EN 253+A1 p. 4.2.2 1.30.16 Measurement of diameter ČSN EN 253+A1 p. 4.3.2.1 1.30.17 1.30.18 1.30.19 Measurement of wall thickness Measurement of wall thickness water vapour transmission rate ČSN EN 253+A1 p. 4.2.3 ČSN EN 253+A1 p. 4.3.2.2 ČSN EN 12086 1.30.20 Bend test ČSN EN 12089 1.30.21 1.30.22 1.30.23 1.30.24 1.30.25 mass per unit volume steady-state thermal transmission properties - by test - by calculation impact resistance setting of blown insulation metal corrosion resistance ČSN EN 1602 ČSN EN ISO 8990 ČSN EN ISO 6946 p. 5, 7 ČSN EN 253+A1 p. 5.4.6 ISO/CD 18393 1.31 Road equipment, road signs, lighting poles 1.31.1 Impact test (verification of secondary safety risk of falling debris) ČSN EN 15101-1 Annex E ČSN EN 1794-2 Annex B Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Building materials Thermal insulation materials and products Thermal insulation materials and products Thermal insulating materials Elements of noise barriers Page 17 of 91
1.31.2 Testing of stone impact resistance 1.32 Thermal insulation systems 1.32.1 1.32.2 1.32.3 1.32.4 1.32.5 1.32.6 1.32.7 1.32.8 adhesion to the substrate resistance to frost tensile strength and elongation of mesh water absorption impact resistance density of fresh mortar mass per unit area of reinforcement mesh dry bulk density of hardened mortar ČSN EN 1794-1 Annex C ETAG 004 p. 5.1.4.1, 5.1.7.1 ETAG 004 p. 5.1.3.2.2 ETAG 004 p. 5.6.7.1 ETAG 004 p. 5.1.3.1 ETAG 004 p. 5.1.3.3. ETAG 004 p. C.1.2.2 ETAG 004 p. C.3.1 ETAG 004 p. C.1.3 Elements of noise barriers Adhesive and screed materials for ETICS Mortars ETICS meshes ETICS ETICS Fresh mortar ETICS Mesh ETICS Base layer ETICS 1.32.9 grain size ETAG 004 p. C.1.1.4 Pastes, powders ETICS 1.33 Loading tests of bridges, building structure and floors 1.33.1* Loading tests of bridges ČSN 73 6209 Bridges 1.33.2* Loading tests of bridges STN 73 6209 Bridges 1.33.3* Load tests ČSN 73 2030 Annex A, B, C 1.34 Masonry, hardware, partition walls, ceilings, floors 1.34.1 impact resistance ISO 7892 Bearing structures and their parts Ventilated facades, partition walls, hand rails 1.35, permanent formwork, ceiling elements, burnt and concrete roofing 1.35.1 water permeability ČSN EN 539-1 Clay roofing tiles 1.35.2 dimensions ČSN EN 772-16 1.35.3 1.35.4 mechanical properties of masonry materials and burnt roofing mechanical properties of masonry materials and burnt roofing ČSN 72 2605 ČSN EN 538 Brick products Clay roofing tiles Page 18 of 91
1.35.5 1.35.6 1.35.7 1.35.8 1.35.9 1.35.10 1.35.11 1.35.12 1.35.13 1.35.14 1.35.15 1.35.16 1.35.17 1.35.18 fracture load of ceiling materials resistance to frost frost resistance of calcium silicate masonry units Testing of dimensional tolerances and mass percentage area of voids in concrete blocks (by paper indentation) net volume and percentage of voids and material in calcium silicate masonry units by filling the voids with sand geometrical characteristics moisture content of calcium silicate masonry units and aerated concrete units water absorption of clay masonry damp proof course units by boiling in water water absorption of concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units water absorption of clay and calcium silicate masonry units by cold water absorption net volume and percentage of voids by hydrostatic weighing mass per unit volume transversal fracture load ČSN 72 2642, p. 13 ČSN 72 2601 Annex A ČSN EN 772-18 ČSN EN 491 p. 5.2-5.5 ČSN EN 772-2 ČSN EN 772-9 ČSN EN 1024 ČSN EN 772-10 ČSN EN 772-7 ČSN EN 772-11 ČSN EN 772-21 ČSN EN 772-3 ČSN EN 772-13 ČSN EN 1344 Annex D Brick products Brick products Concrete roofing tiles Clay roofing tiles Clay pavers Page 19 of 91
1.35.19 moisture movement ČSN EN 772-14 1.35.20 strength ČSN EN 15435 Annex A, B Precast concrete products 1.35.21 1.35.22 1.35.23 1.35.24 1.35.25 1.35.26 1.35.27 1.35.28 Measurement of surface dimensions and characteristics Measurement of surface dimensions and characteristics resistance to concentric load flexural strength flexural strength compressive strength in longitudinal direction compressive strength in longitudinal direction the indirect strength ČSN EN 15037-2+A1 p. 5.1 ČSN EN 15037-3+A1 p. 5.1 ČSN EN 15037-3+A1 p. 5.2.1 ČSN EN 15037-2+A1 p. 5.2.2 ČSN EN 15037-3+A1 p. 5.2.2 ČSN EN 15037-2+A1 p. 5.2.3 ČSN EN 15037-3+A1 p. 5.2.3 ČSN EN 15037-2+A1 p. 5.2.4 Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems 1.35.29 the indirect ČSN EN 15037-3+A1 Beam-and-block floor strength p. 5.2.4 systems 1.35.30 compressive ČSN EN 772-1 strength 1.35.31 water permeability ČSN EN 491 p. 5.7 Concrete roofing tiles 1.35.32 fracture load ČSN EN 491 p. 5.6 Concrete roofing tiles 1.35.33 Frost resistance test ČSN EN 491 p. 5.8 Concrete roofing tiles 1) 1.35.34 resistance to concentric load ČSN EN 15037-2+A1 p. 5.2.1 Beam-and-block floor systems Asterisk at the ordinal identifies the tests, which the Laboratory is qualified to carry out outside the permanent laboratory premises. Page 20 of 91
Explanations: ETAG - Guideline for European Technical Approval C.D.A. WTA ZP STN - Chemical De-Icing Agents - Wissenschaftliche technische Arbeitsgemeinschaft für Bauwesenverhalten und Denkmalpflege - Internal Testing Procedure - Slovak Technical Standard Sampling: Sampling procedure name Sampling procedure identification Sampled object 1.V.1 Fresh concrete sampling ČSN EN 12 350-1 Fresh concrete sampling 1.V.2 sampling ČSN EN 12504-1 p. 2-6 samples 1.V.3 Sampling ČSN EN 13416 Bitumen, plastic and rubber sheets for roof waterproofing 1.V.4 Aggregate sampling ČSN EN 932-1 1.V.5 1.V.6 Sampling and preparation of testing mortars Sampling of cement and fly ash ČSN EN 1015-2 ČSN EN 196-7 Mortars Cement and fly ash sampling Page 21 of 91
2. Testing Laboratory in České Budějovice 2.1 Acoustics 2.1.1 reserved 2.2 Concrete, admixtures and fibres for concrete 2.2.1* Slump test ČSN EN 12350-2 Fresh concrete 2.2.2* Flow table test ČSN EN 12 350-5 Fresh concrete 2.2.3* 2.2.4* 2.2.5 2.2.6 2.2.8 2.2.9 2.2.10* 2.2.11* 2.2.12 2.2.13 2.2.14 2.2.15 2.2.16 mass per unit volume air content pressure methods compressive strength of concrete tensile strength of concrete concrete frost resistance cement concrete surface resistance to water and chemical deicing agents Testing of shapes and dimensions compressive strength of concrete, including the manufacture and treatment of test specimens compressive strength of test specimens flexural strength of test specimens the indirect tensile strength of test specimens density of hardened concrete depth of penetration of water under pressure ČSN EN 12350-6 ČSN EN 12350-7 ČSN 73 1317 ČSN 73 1318 ČSN 73 1322 ČSN 73 1326, A, C method ČSN EN 12390-1 ČSN EN 12390-2 ČSN EN 12390-3 ČSN EN 12504-1 ČSN EN 12390-3 ČSN EN 12390-5 ČSN EN 12390-6 ČSN EN 12390-7 ČSN EN 12390-8 Fresh concrete Fresh concrete Page 22 of 91
2.2.17 2.2.18 2.2.19 2.2.20 2.2.22* 2.2.23* 2.2.24* 2.2.25* 2.2.26 2.2.27 2.2.28 2.2.29 2.2.37* 2.2.38* 2.2.39* 2.2.40* static modulus of elasticity in compression moisture content, absorption power and capillarity watertightness concrete frost resistance by accelerated tests Test of compressive strength rebound by hardness drop tester Test of compressive strength by hardness testing methods (Schmidt N. L.) Testing of concrete by hardness testing methods (Schmidt N. L.) setting time bleeding of concrete capillary absorption solids content layer adhesion and tensile strength of surface layers and impermeability Measurement of pavement surface macrotexture depth using a volumetric patch technique Measurement and assessment of irregularity of pavement courses Testing of impermeability of layers by measuring their electric resistance ČSN ISO 1920-10 ČSN 73 1316 ČSN 73 1321 ČSN 73 1325 ČSN EN 12504-1 ČSN EN 12504-2 ČSN 73 1373 ČSN 73 2011 ČSN EN 480-2 ČSN EN 480-4 ČSN EN 480-5 ČSN EN 480-8 ČSN 73 6242 Annex B ČSN EN 13036-1 ČSN 73 6175 p. 8 ČSN 73 6242 Annex D Concrete and mortar additives Concrete and mortar additives Concrete and mortar additives Concrete and mortar additives Bridges surfaces Bridges surfaces Bridges surfaces Bridges surfaces Page 23 of 91
2.2.42 static modulus of elasticity in compression 2.3 Small concrete products 2.3.1* 2.3.2* 2.3.3* 2.3.4 2.3.5 2.3.6 2.3.7 2.3.8 2.3.9 dimensions dimensions dimensions total water absorption total water absorption total water absorption the indirect tensile strength flexural strength and fracture load bending strength ČSN ISO 6784 ČSN EN 1338 Annex C ČSN EN 1339 Annex C ČSN EN 1340 Annex C ČSN EN 1338 Annex E ČSN EN 1339 Annex E ČSN EN 1340 Annex E ČSN EN 1338 Annex F ČSN EN 1339 Annex F ČSN EN 1340 Annex F 2.4 Concrete building components and structures 2.4.1* 2.4.2 2.4.4* 2.4.5 2.4.6 dimensions, shapes, top layer of reinforcement, crack width water absorption dimensions, shapes, top layer of reinforcement, crack width Tests of strength and load bearing capacity Tests of strength and load bearing capacity ČSN EN 13369 Annex J ČSN EN 13369 Annex G ČSN EN 15037-1 Annex H ČSN EN 1916 Annex C, D ČSN EN 1917 only Annex A, B, C 2.4.7* Static loading test ČSN EN 15037-1 Annex H 2.4.9 watertightness ČSN EN 1917 Annex C Concrete components Concrete components Concrete girders for ceiling structures Concrete pipes Concrete manholes Concrete girders for ceiling structures Concrete manholes Page 24 of 91
2.5 Timber, timber components, timber based and fibre-cement products 2.5.1* Static loading tests ČSN EN 380 Timber structures 2.6 Physical factors 2.6.1* air permeability of buildings ČSN EN 13829 2.7 Glass grids, geotextiles and geotextile-related products 2.7.1 tensile strength and elongation of mesh ČSN EN 13496 Buildings Glass fibre mesh 2.8 Games, toys and school supplies, playgrounds, matches and lighters 2.8.1 reserved 2.9 Materials, products and waterproofing systems 2.9.1 watertightness ČSN EN 14891 method A.7 2.9.2 Water absorption test ČSN 50 3602 p. 46-48 2.9.3 2.9.4 mass per unit area the crackbridging ČSN 50 3602 p. 10 and 11 ČSN EN 14891 method A.8 2.9.5 adhesion ČSN EN 14891 method A.6 2.10 Household chemicals cleaning and washing agents 2.10.1 reserved 2.11 Chemical analyses of silicate and building products 2.11.1 reserved 2.12 Stone, aggregates, inactive concrete admixtures, soils 2.12.1 2.12.2 2.12.3 resistance to freezing and thawing various aggregate particles Tests of aggregate fines Loss by drying ČSN EN 1367-1 ČSN 72 1180 ČSN 72 1187 Liquid-applied water impermeable products used under ceramic tiling Covering and insulation materials in rolls Covering and insulation materials in rolls Liquid-applied water impermeable products used under ceramic tiling Liquid-applied water impermeable products used under ceramic tiling Page 25 of 91
2.12.4 2.12.5 2.12.6 2.12.7 2.12.8 2.12.9 2.12.11 2.12.12 2.12.13 2.12.14 2.12.15 2.12.16 2.12.17 particle size distribution Sieving analysis particle shape - Flakiness index particle shape - Shape index percentage of crushed and broken surfaces in coarse aggregate particles Assessment of fines Sand equivalent test Assessment of fines Methylene blue test Classification test for the constituents of coarse recycled aggregate resistance to wear resistance to fragmentation loose bulk density and voids the water content by drying in a ventilated oven particle density and water absorption particle density and water absorption ČSN EN 933-1 ČSN EN 933-3 ČSN EN 933-4 ČSN EN 933-5 ČSN EN 933-8 ČSN EN 933-9+A1 ČSN EN 933-11 ČSN EN 1097-1 ČSN EN 1097-2 ČSN EN 1097-3 ČSN EN 1097-5 ČSN EN 1097-6 ČSN EN 1097-7 2.12.18 Magnesium sulfate test ČSN EN 1367-2 2.12.19 2.12.20 2.12.21 Tests for thermal and weathering properties of aggregates boiling test drying shrinkage Testing of chemical properties of aggregates ČSN EN 1367-3 ČSN EN 1367-4 ČSN EN 1744-1+A1 p. 15.1 Page 26 of 91
2.12.22 2.12.23 2.12.24 2.12.25 2.12.26 2.12.28 dense aggregate durability by accelerated test with sodium sulphate resistance of aggregates to freezing by freeze test resistance to fragmentation ČSN 72 1176 method A ČSN 72 1176 method B ČSN EN 13450 Annex C resistance ČSN EN 13450 Annex F to freezing and thawing resistance of aggregates to magnesium ČSN EN 13450 Annex G sulphate resistance ČSN EN 13055-1 Annex A to fragmentation resistance 2.12.29 to freezing and thawing 2.12.31* compaction of soils and backfills density 2.12.32* with cutting ring 2.12.33* compactability Proctor compaction ČSN EN 13055-1 Annex C ČSN 72 1006 ČSN 72 1010 method A ČSN EN 13286-2 2.13 Anchoring elements, including rail fasteners 2.13.1 reserved 2.14 Metallic materials and parts in construction Lightweight aggregates Lightweight aggregates Soils and backfills Soils and backfills Soils and backfills 2.14.1* Performance of tensile tests ČSN EN ISO 6892-1 Metallic products 2.14.2 Bend test ČSN EN ISO 7438 Metallic products 2.14.3 Bend test ČSN EN ISO 5173 Metallic products 2.15 2.15.1 reserved Chimneys, chimney sheaths and flues, refractory materials and products, ceramic raw materials 2.16 Light industry products 2.16.1 reserved Page 27 of 91
2.17 Mortars, mortar mixtures, renovation materials, screeds 2.17.1 Frost resistance test ČSN 72 2452 Masonry mortars 2.17.2 2.17.3 2.17.4 2.17.5 2.17.6 2.17.7 particle size distribution (by sieve analysis) consistence of fresh mortar by flow table consistence of fresh mortar (by plunger penetration) density of fresh mortar air content of fresh mortar workable life and correction time of fresh mortar ČSN EN 1015-1 ČSN EN 1015-3 ČSN EN 1015-4 ČSN EN 1015-6 ČSN EN 1015-7 ČSN EN 1015-9 Dry mixtures Fresh mortar Fresh mortar Fresh mortar Fresh mortar Fresh mortar 2.17.8 dry bulk density of hardened mortar ČSN EN 1015-10 Dry mortar 2.17.9 2.17.10 2.17.11 compressive strength of mortar Test of compressive strength flexural strength of mortar ČSN EN 1015-11 ČSN EN 13892-2 ČSN EN 1015-11 Dry hardened mortar Screed materials Dry hardened mortar 2.17.12 Test of flexural strength ČSN EN 13892-2 Screed materials 2.17.13* adhesion ČSN EN 1015-12 Dry hardened mortar 2.17.14 adhesion of cementitious adhesives ČSN EN 1348 Mortars and adhesives 2.17.15* adhesion ČSN EN 13892-8 Screed materials 2.17.16 water absorption coefficient due to capillary action of hardened mortar ČSN EN 1015-18 Mortars Page 28 of 91
2.17.17 2.17.18 water vapour permeability of surface finish of building structures the compatibility of one-coat rendering mortars with substrates ČSN EN 1015-19 ČSN EN 1015-21 Mortars Mortars 2.17.19 slip ČSN EN 1308 Mortars and adhesives 2.17.20 shear adhesion strength of dispersion adhesives ČSN EN 1324 Mortars and adhesives 2.17.21 open time ČSN EN 1346 Mortars and adhesives 2.17.22 2.17.23 2.17.24 2.17.25 2.17.26 2.17.27 2.17.28 transverse deformation for cementitious adhesives and grouts shear adhesion strength of reaction resin adhesives dimensional variations water retention capability water vapour diffusion resistance factor capillary water absorption water penetration depth ČSN EN 12002 ČSN EN 12003 ČSN EN 13872 WTA 2-9-04/D p. 6.2.4 WTA 2-9-04/D p. 6.3.2 WTA 2-9-04/D p. 6.3.6 WTA 2-9-04/D p. 6.3.7 Mortars and adhesives Mortars and adhesives Screed materials Renovation plasters Renovation plasters Renovation plasters Renovation plasters 2.17.29 porosity WTA 2-9-04/D p. 6.3.9 Renovation plasters 2.17.30 2.17.31 2.17.32 resistance of renovation plasters to salt linear shrinkage thermal compatibility Freeze-thaw cycling with de-icing salt immersion WTA 2-9-04/D p. 6.3.10 ČSN EN 12617-1 ČSN EN 13687-1 Renovation plasters Renovation materials Renovation materials Page 29 of 91
2.17.33 2.17.34 2.17.35 2.17.36 2.17.37 2.17.38 2.17.39 Freeze-thaw cycling without de-icing salt immersion shrinkage and expansion compressive strength of repair mortar resistance to capillary absorption Measurement of bond strength by pull-off coefficient of thermal expansion setting time ČSN EN 13687-3 ČSN EN 12617-4 p. 6, 7 ČSN EN 12190 ČSN EN 13057 ČSN EN 1542 ČSN EN 1770 p. 4 ČSN EN 13294 2.18 Tanks, reservoirs, septic tanks, water treatment plants Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials 2.18.1* Water tightness test ČSN 75 0905 Tanks 2.19 Water, aqueous extracts, waste, sludge 2.19.1 reserved 2.20 Draining elements 2.20.1 reserved 2.21 Doors and windows, roof lights, hardware 2.21.1 reserved 2.22 Gasolines, diesel oil, biofuels, oils, combustible and other liquids, lubricants 2.22.1 reserved 2.23 Plastics and composites 2.23.1 2.23.2 2.23.3 2.23.4 water absorption of plastics tensile properties tensile properties the effects of immersion in liquid chemicals (including water) ČSN EN ISO 62 ČSN EN ISO 527-2 ČSN EN ISO 527-3 ČSN EN ISO 175 Plastics Plastics Plastics Plastics Page 30 of 91
2.24 Construction cements, fly ash, slags, stabilization of soils, bitumens 2.24.1 2.24.2 2.24.3 2.24.4 normal density and setting time of cement volume stability of cement the strength of cement bulk density ČSN EN 196-3+A1 p. 5, 6 ČSN EN 196-3+A1 p. 5, 7 ČSN EN 196-1 ČSN EN 459-2 p. 5.8 2.25 Products and systems for prestressing of structures 2.25.1 reserved Cement, masonry cement Cement, masonry cement Cement, masonry cement Lime 2.26 Gypsum and gypsum products, rock gypsum, anhydride, MgO based panels 2.26.1 2.26.2 flexural strength compressive strength ČSN EN 13279-2 p. 4.5.4 ČSN EN 13279-2 p. 4.5.5 2.26.3 adhesion ČSN EN 13279-2 p. 4.6 2.26.4 2.26.5 consistence and workable life compressive strength and flexural strength 2.26.6 ph 2.26.7 2.26.8 setting time shrinkage and expansion 2.27 Construction and sanitary ceramics 2.27.1 reserved ČSN EN 13454-2+A1 p. 5.2 ČSN EN 13454-2+A1 p. 4.4, 5.3 ČSN EN 13454-2+A1 p. 4.2, 5.1 ČSN EN 13454-2+A1 p. 4.3 ČSN EN 13454-2+A1 p. 4.5, 5.4 2.28 Machinery, building and bridge bearings, elevators 2.28.1 reserved Gypsum binders and gypsum plasters Gypsum binders and gypsum plasters Gypsum binders and gypsum plasters Binders, composite binders Binders, composite binders and factory made mixtures for floor screeds Binders, composite binders and factory made mixtures for floor screeds Binders, composite binders and factory made mixtures for floor screeds Binders, composite binders 2.29 Cements, adhesives, jointing materials, paints and coatings, surface finishes 2.29.1* adhesion ČSN 73 2577 Surface finish Page 31 of 91
2.29.2* 2.29.3 2.29.4 2.29.5 2.29.6 2.29.7 watertightness resistance to frost water vapour transmission properties resistance to rapid temperature changes resistance to liquids resistance to liquids ČSN 73 2578 ČSN 73 2579 ČSN 73 2580 ČSN 73 2581 ČSN EN ISO 2812-1 ČSN EN ISO 2812-2 Surface finish Surface finish Surface finish Surface finish Surface finish Surface finish 2.29.8 Pull-off test for adhesion ČSN EN ISO 4624 Surface finish 2.29.9 2.29.10 water vapour transmission rate water permeability ČSN EN ISO 7783 ČSN EN 1062-3 Surface finish Surface finish 2.29.11 Drop weight test ČSN EN ISO 6272-1 Surface finish 2.29.12 shear strength ČSN EN 1465 Adhesives 2.29.13 Shear test ČSN EN 1373 Adhesives 2.29.14 2.29.15 2.29.16 2.29.17 2.29.18 2.29.19 2.29.20 dimensional variations dimensional changes after ageing elastic recovery resistance to flow adhesion and cohesion volume changes adhesion and cohesion at maintained extension after immersion in water ČSN EN 1841 ČSN EN 1903 ČSN EN ISO 7389 ČSN EN ISO 7390 ČSN EN ISO 9046 ČSN EN ISO 10563 ČSN EN ISO 10590 Adhesives Adhesives Sealants Sealants Sealants Sealants Sealants Page 32 of 91
2.29.21 2.29.22 2.29.23 2.29.24 adhesion and cohesion properties after immersion in water tensile properties tensile properties at maintained extension flexural and compressive strength ČSN EN ISO 10591 ČSN EN ISO 8339 ČSN EN ISO 8340 ČSN EN 12808-3 Sealants Sealants Sealants Grouts for tiles 2.29.25 shrinkage ČSN EN 12808-4 Grouts for tiles 2.29.26 water absorption ČSN EN 12808-5 Grouts for tiles 2.29.27 Peel test ČSN EN 1372 Adhesives 2.30 Thermal insulation materials and products, thermal tests 2.30.1* length and width ČSN EN 822 2.30.2* thickness ČSN EN 823 2.30.3* squareness ČSN EN 824 2.30.4* flatness ČSN EN 825 2.30.5 Pressure test ČSN EN 826 2.30.6 2.30.7 2.30.8 2.30.9 2.30.10 tensile strength perpendicular to faces dimensional stability under specified temperature and humidity conditions dimensional stability at constant laboratory conditions water absorption by partial immersion long term water absorption by immersion ČSN EN 1607 ČSN EN 1604 ČSN EN 1603 ČSN EN 1609 ČSN EN 12087 method 1A, 2A Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Page 33 of 91
2.30.11 water vapour transmission rate ČSN EN 12086 2.30.12 Bend test ČSN EN 12089 2.30.13 2.30.15 2.30.16 2.30.17 2.30.18 2.30.19 2.30.20 2.30.21 2.30.22 2.30.23 2.30.24 mass per unit volume thermal resistance by means of guarded hot plate and heat flow meter methods steadystate thermal transmission properties steady state thermal resistance and related quantities Guarded hot plate apparatus steady state thermal resistance and related quantities Guarded hot plate apparatus steady state thermal resistance and related quantities Guarded hot plate apparatus steady state thermal resistance and related quantities Guarded hot plate apparatus behaviour under point load shear behaviour pressure forming setting of blown insulation ČSN EN 1602 ČSN EN 12667 ČSN EN ISO 8990 ISO 8302 ČSN 72 7012-1 ČSN 72 7012-2 ČSN 72 7012-3 ČSN EN 12430 ČSN EN 12090 ČSN EN 1606 ČSN EN 14064-1 2.31 Road equipment, road signs, lighting poles Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Building materials Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products Thermal insulation materials and products 2.31.1 reserved 2.32 Thermal insulation systems 2.32.1 adhesion to the substrate ETAG 004 p. 5.1.4.1, 5.1.7.1 Adhesive and screed materials for ETICS Page 34 of 91
2.32.2 2.32.3 2.32.4 2.32.5 2.32.6 2.32.7 2.32.8 resistance to frost tensile strength and elongation of mesh Tensile test perpendicular to the faces - in wet conditions ETICS render strip tensile test water absorption impact resistance resistance to elongation ETAG 004 p. 5.1.3.2.2 ETAG 004 p. 5.6.7.1 ETAG 004 p. 5.2.4.1.2 ETAG 004 p. 5.5.4.1 ETAG 004 p. 5.1.3.1 ETAG 004 p. 5.1.3.3.1, 5.1.3.3.2 ETAG 004 p. 5.1.4.3.1. Mortars ETICS meshes ETICS insulant Screed material for ETICS ETICS ETICS ETICS 2.32.9 Static foam block test ETAG 004 p. 5.1.4.3.2. ETICS 2.32.10 mass per unit volume ETAG 004 p. C.1.1.1 Adhesive and screed materials, plasters and liquids ETICS 2.32.11 dry matter ETAG 004 p. C.1.1.2 Plasters and liquids ETICS 2.32.12 2.32.13 2.32.14 2.32.15 ash content water retention capability density of fresh mortar shrinkage of base coat ETAG 004 p. C.1.1.3 ETAG 004 p. C.1.2.1 ETAG 004 p. C.1.2.2 ETAG 004 p. C.1.3.1.2 Pastes and liquids ETICS Fresh mortar ETICS Fresh mortar ETICS Base coat ETICS 2.32.16 Products with a thickness up to 5 mm: static modulus of elasticity, tensile strength and elongation at break ETAG 004 p. C.1.3.2 Base coat ETICS 2.32.17 2.32.18 2.32.19 mass per unit area of reinforcement mesh ash content of reinforcement mesh mesh size and of filaments ETAG 004 p. C.3.1 ETAG 004 p. C.3.2 ETAG 004 p. C.3.3 Mesh ETICS Mesh ETICS Mesh ETICS Page 35 of 91
2.32.20 dry bulk density of hardened mortar ETAG 004 p. C.1.3 Base coat ETICS 2.32.21 grain size ETAG 004 p. C.1.1.4 Pastes, powders ETICS 2.32.22 2.32.23 2.32.24 2.32.25 Bracket resistance to vertical load (dead weight) Bracket resistance to horizontal load (wind suction) hygrothermal behaviour Test methods for foam adhesives for ETICS ETAG 034-2 Annex E ETAG 034-2 Annex E ETAG 004 p. 5.1.3.2.1 EOTA TR 46 2.33 Loading tests of bridges, building structure and floors Ventilated facades Ventilated facades ETICS Foam adhesives 2.33.1* Loading tests of bridges ČSN 73 6209 Bridges 2.33.2* Loading tests of building structures ČSN 73 2030 2.34 Masonry, hardware, partition walls, ceilings, floors 2.34.1 reserved 2.34.1 2.34.2* 2.34.3* initial shear strength of masonry flexural resistance and shear resistance of lintels dimensions and bow of lintels ČSN EN 1052-3 ČSN EN 846-9 ČSN EN 846-11 Bearing structures and their parts Masonry Ancillary components for masonry Ancillary components for masonry 2.35, permanent formwork, ceiling elements, burnt and concrete roofing 2.35.1 2.35.2 2.35.3 2.35.4 dimensions mechanical properties of masonry materials and burnt roofing resistance to frost Testing of dimensional tolerances and mass ČSN EN 772-16 ČSN 72 2605 ČSN 72 2601 ČSN EN 491 p. 5.2, 5.5 Brick products Brick products Concrete roofing tiles Page 36 of 91
2.35.5 2.35.6 2.35.7 2.35.8 2.35.9 2.35.10 percentage area of voids in concrete blocks (by paper indentation) water absorption of clay masonry damp proof course units by boiling in water water absorption of concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units net volume and percentage of voids by hydrostatic weighing mass per unit volume moisture movement ČSN EN 772-2 ČSN EN 772-7 ČSN EN 772-11 ČSN EN 772-3 ČSN EN 772-13 ČSN EN 772-14 2.35.11 strength ČSN EN 15435 Precast concrete products 2.35.12 2.35.13 2.35.14 2.35.15* 2.35.16 2.35.17 2.35.18 2.35.19 mass, density and water absorption susceptibility to efflorescence flatness of faces appearance and dimensions presence of lime nodules compressive strength water permeability fracture load ČSN 72 2603 ČSN 72 2608 ČSN EN 772-20 ČSN 72 2602 ČSN 72 2607 ČSN EN 772-1 ČSN EN 491 p. 5.7 ČSN EN 491 p. 5.6 Brick products Brick products Brick products Brick products Concrete roofing tiles Concrete roofing tiles Page 37 of 91