OWNERS GUIDE TO INSTALLATION AND OPERATION END SUCTION CENTRIFUGAL PUMPS

OWNERS GUIDE TO INSTALLATION AND OPERATION END SUCTION CENTRIFUGAL PUMPS IL00 Figure - CJ0, EL0 Series IL0 Figure - CJ0, EL0 Series Drain Plug READ THESE INSTRUCTIONS CAREFULLY Read these installation instructions in detail before installing your pump. Be sure to check the following:. Be certain the motor is connected for the correct line voltage being used (check motor nameplate).. Be certain the pump is completely primed before starting. Otherwise damage may occur to the seal. Every pump is tested before leaving the factory, and its performance depends largely on the installation. GENERAL SAFETY INFORMATION. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).. Replace damaged or worn wiring cord immediately.. Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces or chemicals.. Protect the power cable from coming in contact with sharp objects. 5. Be careful when touching the exterior of an operating motor - it may be hot enough to be painful or cause injury. 6. Make certain that the power source conforms to the requirements of your equipment. 7. Always disconnect power source before performing any work on or near the motor or its connected load. If the power disconnect point is out-of-sight, lock it in the open position and tag it to prevent unexpected application of power. Failure to do so could result in fatal electrical shock.. Do not handle the pump with wet hands or when standing in water as fatal electrical shock could occur. Disconnect main power before handling unit for ANY REASON!. Unit must be securely and adequately electrically grounded. This can be accomplished by wiring the unit to a ground metal-clad raceway system or by using a separate ground wire connected to the bare metal of the motor frame or other suitable means. 0. Risk of electric shock. This pump has not been investigated for use in swimming pool areas.. This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. NOTE: Pumps with the CSA mark are tested to UL standard UL77 and certified to CSA standard C. No. 0. Copyright 0. All rights reserved. 0 D

Dimensions (In Inches) CJ0/EL0 Series Chart A HP A B C D E F G H J K / -5/ -/6 -/6 -/6 -/ -/ -/ -/ -7/ / -5/ -/6 -/6 -/6 -/ -/ -/ -/ -7/ / -5/ -/6 -/6 -/6 -/ -/ -/ -7/ -5/ -/6 -/6 -/6 -/ -/ -/ -/ -7/ -/ -5/ -/6 -/6 -/6 -/ -/ -/ 5-/ -7/ -5/ -/6 -/6 -/6 -/ -/ -/ 5-5/ -7/ -/ Discharge -/ Suction F K -/ Discharge F -/ Suction H E H E D D A C B J A C IL06-A B G J IL05 G Figure - CJ0/EL0 Single Stage Booster Pump Figure - CJ0B/EL0B Two and Three Stage Booster Pump CJ0/EL0 Series HP A B C D E F G H J / -5/ 7-/6 -/6 -/ 6-/ 7 -/ 7-7/ -5/ 7-/6 -/6 -/ 6-/ 7 -/ -/ -/ -5/ 7-/6 -/6 -/ 6-/ 7 -/ -5/ 7-/6 -/6 -/ 6-/ 7 -/ -/ * -5/ -7/6 -/6 -/ -/ 7 -/ -/ * -5/ -7/6 -/6 -/ -/ 7 -/ -/ (*) Three Stage Motor Data HP PH VOLTS HZ RPM MOTOR VOLTAGE (FACTORY) SERVICE FACTOR MOTOR AMPS Chart B Chart C LOCKED ROTOR AMPS SINGLE PHASE THREE PHASE SINGLE PHASE THREE PHASE CONNECT. 5V 0V 0V 60V 5V 0V 0V 60V / 5/0 60 50 5V.6. 6.0.0 K / 5/0 60 50 5V.0 6.5 6.0.0 K / 5/0 60 50 0V.0 7.0 5.0 6.0 K 5/0 60 50 0V.0.0 70.0.0 L -/ 5/0 60 50 0V.0 0.5.0.0 J 5/0 60 50 0V 5.0.5 6.0 5.0 H 0 60 50 0V.5 5.0 D / 0-0/60 60/50 50/50 0V.5.75.0.5 K 0-0/60 60/50 50/50 0V.5.5 6..5 K -/ 0-0/60 60/50 50/50 0V 5.7.5.5 6. K 0-0/60 60/50 50/50 0V 7..0.0.0 K 0-0/60 60 50 0V...0.0 D DISTANCE FROM MOTOR TO FUSE BOX METER, OR ELECTRICAL OUTLET Chart D MINIMUM COPPER WIRE SIZE CHART (GAUGE) SINGLE PHASE MOTORS THREE PHASE MOTORS / HP / HP / HP HP -/ HP HP HP / HP HP -/ HP HP HP 5V 0V 5V 0V 5V 0V 5V 0V 5V 0V 5V 0V 0V 0V 60V 0V 60V 0V 60V 0V 60V 0V 60V 0-50 0 0 0 0 50-00 0 0 00-50 0 0 6 6 0 50-00 0 * 0 * 0 0 00-00 0 6 0 * 0 * 0 0 0 Breaker Size (Amps) 5 5 0 5 0 5 0 5 0 0 0 0 0 5 5 5 5 5 5 5 5 5 5 (*) Not economical to run in 5 volt, use 0 volts KVA Copyright 0. All rights reserved.

Street Supply Line Strainer or Filter (Optional) Check Valve Gauge Typical Installations Gate/Ball Valve (Normally open) Check Valve Switch Tank Switch Gauge Main Power Box Fuse Box or Switch To size pressure tank properly, match the drawdown of the tank to the capacity of the pump. (*) For manual operation, omit the pressure tank and pressure switch. Wire motor direct to fuse box. Install a pressure relief valve on any installation where pump pressure can exceed the pressure tank s maximum working pressure or on systems where the discharge line can be shut off or obstructed. Extreme over pressure can result in personal injury or property damage. Figure 5 Drain Relief Valve IL0 To size pressure tank properly, match the drawdown of the tank to the capacity of the pump. (*) For manual operation, omit the pressure tank and pressure switch. Wire motor direct to fuse box. Install a pressure relief valve on any installation where pump pressure can exceed the pressure tank s maximum working pressure or on systems where the discharge line can be shut off or obstructed. Extreme over pressure can result in personal injury or property damage. Vacuum Gauge Foot Valve with Strainer Gauge Gate/Ball Valve (Normally open) Switch Tank Switch Gauge Main Power Box Fuse Box or Switch Figure 6 Drain Relief Valve IL0 Copyright 0. All rights reserved.

MODEL NO. PHASE PHASE CJ0B07AB CJ0B07TAB CJ0B0AB EL0B0 CJ0B0TAB CJ0B5AB EL0B5 CJ0B5TAB CJ0B0AB EL0B0 CJ0B0TAB CJ0C0AB EL0C0 CJ0C0TAB CJ0C0AB EL0C0 CJ0C0TAB CJ0B07AB CJ0B07TAB CJ0B0AB CJ0B0TAB Pump Performance CJ0/EL0 SERIES CENTRIFUGAL PUMPS, LOW LEAD BRASS IMPELLERS HP STAGES LIFT FT. / CJ0B5AB CJ0B5TAB / CJ0B0AB CJ0B0TAB CJ0C0AB CJ0C0TAB CJ0C0AB CJ0C0TAB Discharge PSI 0 0 0 0 50 60 70 0 0 CAPACITY U.S. GPM 5 5 5 6 5 5 6 5 0 6 5 5 7 7 5 7 0 5 0 5 56 5 7 5 50 5 5 7 6 5 7 5 7 0 6 5 5 5 6 5 5 5 5 56 5 5 7 5 50 6 7 5 7 6 6 5 0 MAX. PSI CASE LIQUID TEMP. 5 60psig 00º F 6 60psig 00º F 6 60psig 00º F 70 60psig 00º F 60psig 00º F 5 60psig 00º F MODEL NO. PHASE PHASE CJ0P07 CJ0P07 / CJ0P0 EL0P0 CJ0P5 EL0P5 CJ0P0 EL0P0 CJ0D0 EL0D0 CJ0D0 EL0D0 CJ0P0 CJ0P5 / CJ0P0 CJ0D0 CJ0D0 CJ0/EL0 SERIES CENTRIFUGAL PUMPS, PLASTIC IMPELLERS HP STAGES LIFT FT. Discharge PSI 0 0 0 0 50 60 70 0 0 5 5 0 5 6 5 CAPACITY U.S. GPM 5 5 0 5 0 5 6 5 5 5 0 5 5 50 5 6 5 5 7 5 7 5 55 5 7 5 7 5 0 7 5 7 6 6 5 7 6 5 6 6 6 6 5 0 5 0 5 6 6 0 5 5 5 5 50 7 5 5 5 7 6 5 7 0 5 6 6 6 5 7 Do not exceed the maximum case pressure and maximum liquid temperature rating of the pump Performance shown for 60Hz models. 50 Hz models also available. Suction and Discharge Tappings -/ X -/ MAX. PSI CASE LIQUID TEMP. 60psig 60º F 60 60psig 60º F 6 60psig 60º F 67 60psig 60º F 0 60psig 60º F 5 60psig 60º F Copyright 0. All rights reserved.

MODEL NO. PHASE PHASE CJ00AB / CJ005AB EL005 CJ005TAB CJ007 EL007 CJ007T CJ00 EL00 CJ00T CJ05 EL05 CJ05T CJ00 EL00 CJ00T CJ007 CJ007T CJ00 CJ00T CJ05 CJ05T CJ00 CJ00T CJ0/EL0 SERIES CENTRIFUGAL PUMPS, LOW LEAD BRASS IMPELLERS HP STAGES LIFT FT. / / / Discharge PSI 0 5 0 5 0 5 0 5 50 CAPACITY U.S. GPM 5 5 6 6 5 5 50 7 7 5 5 0 5 0 5 5 7 6 5 6 5 66 5 0 5 57 5 5 76 6 6 50 6 6 5 7 65 5 5 66 57 5 5 0 70 5 5 5 75 6 7 5 7 7 66 5 5 0 0 6 6 75 6 5 0 0 67 5 5 0 5 7 5 MAX. PSI CASE LIQUID TEMP. 7 00psig 00º F 00psig 00º F 00psig 00º F 00psig 00º F 00psig 00º F 00psig 00º F MODEL NO. PHASE PHASE CJ0P0 EL0P0 CJ0P05 EL0P05 CJ0P07 EL0P07 CJ0P0 EL0P0 CJ0P5 EL0P5 CJ0/EL0 SERIES CENTRIFUGAL PUMPS, PLASTIC IMPELLERS HP STAGES LIFT FT. / CJ0P05 / CJ0P07 / CJ0P0 CJ0P5 / Discharge PSI 0 5 0 5 0 5 0 5 50 CAPACITY U.S. GPM 5 5 5 5 5 6 5 5 5 6 5 5 7 5 6 6 6 57 0 5 6 6 57 6 5 5 5 67 65 6 6 5 5 5 6 5 5 55 5 7 6 5 5 6 67 66 65 6 5 5 6 6 60 5 55 5 7 6 5 MAX. PSI CASE LIQUID TEMP. 6 00psig 60º F 00psig 60º F 00psig 60º F 0 00psig 60º F 00psig 60º F Do not exceed the maximum case pressure and maximum liquid temperature rating of the pump. Performance shown for 60Hz models. 50 Hz models also available. Models with suffix T denotes TEFC motor. All other models utilize ODP motors. Suction and Discharge Tappings -/ X -/ 5 Copyright 0. All rights reserved.

INSPECTION AND STORAGE When unpacking the unit, inspect carefully for any damage that may have occurred during shipment. If the unit is received sometime before it can be used, it should be inspected, recrated and stored in a dry location. LOCATION IMPORTANT: In installations where property damage might result from an inoperative or leaking pump due to power outages, discharge line blockage or any other reason, a back-up system (s) and/or warning system (s) should be used.install a gate valve and union in the suction and discharge lines. For removal of the pump for service, close the gate valve and disconnect the union.. Locate pump as close to the fluid source as possible.. Place unit where the motor electrical components and piping are protected from the weather and extremes of heat, humidity and below freezing temperatures.. Mount unit in a dry location that is easily accessible for inspection and maintenance. If a dry location is not available, mount it on a foundation well above the wet floor.. Allow ample clearance around unit for free air circulation. 5. CJ0/EL0 Series pumps incorporate a discharge port on the pump casing that can be adjusted in 0 increments. If necessary, adjust the discharge port to accommodate the specific application. Pump performance will not be affected by the position of the discharge port. 6. This unit is not waterproof, and is not intended to be used in showers, saunas, or other potentially wet locations. The motor is designed to be used in a clean, dry location with access to an adequate supply of cooling air. Ambient temperature around the motor should not exceed 0 F (0 C). For outdoor installations, motor must be protected by a cover that does not block airflow to and around the motor. This unit is not weatherproof, nor is it able to be submersed in water, or any other liquid. SUCTION LIMITATIONS. Units are non self-priming. Normally after being primed the total suction lift of the pump is 5 feet. Suction lift varies depending upon elevation (altitude) and water temperature. See Practical Suction Lift chart.. Where liquids at or near their boiling points are being handled, the supply must be located above the suction, so that the available NPSH will be greater than that required by the unit. Practical Suction Lifts at Various Elevations and Water Temperatures in Degrees Fahrenheit Altitude 60º 0º 00º 0º 0º 60º 0º 00º Sea Level - - -0 - -5-0 - +5 000-0 - - -6 - -7 - + 000-7 -6-5 - -0 - + + 6000-5 - - - -7 - +6 +6 000 - - -0 - - + + 0000-0 - - -6 - + + This table gives the maximum permissible suction lift or the minimum head permitted on the suction side of a pump at various altitudes and liquid temperatures. A minus sign before a number indicates suction lift. A plus sign before a number indicates minimum head. These figures are to be used as a guide. PIPING. Use galvanized piping, rigid plastic or other suitable pipe that will not collapse under suction or rupture due to pressure.. The diameter of the suction and discharge pipe should be no smaller than the corresponding tappings of the pump (see Figure & ). If long runs are encountered larger pipe should be used. Smaller pipe will reduce the capacity of the pump.. All joints and connections should have Teflon tape or pipe sealing compound (male threads only) applied and drawn up tightly. The entire system must be air and water tight for efficient operation. PUMP INSTALLATION Refer to Figures 5, 6, and 7 for typical installations. Both the suction and discharge pipe should be supported at a point near the pump to avoid strains being placed on the pump.. If the pump is used as part of a permanent installation, secure to a rigid foundation with appropriate fasteners.. Locate the pump as close to the water as possible, keeping the suction pipe as short as conditions permit.. Avoid dips or pockets in offset piping or air will accumulate at high points which will make priming difficult.. The suction pipe should slope upward to the pump inlet. A horizontal suction line must have a gradual rise to the pump. Gauge Priming Plug Discharge Tee Suction Pipe Installed with Gradual Rise to Pump Inlet Rigid Foundation Level Pipe Support IL05 6 Figure 7 Copyright 0. All rights reserved.

5. On suction lift installations, a foot valve located in the water or a check valve located as close to the water as possible will reduce priming time of the pump and help maintain prime. A strainer must be used on the suction line to filter out dirt and debris. 6. A priming tee installed in the pump discharge port allows water to be poured into the pump case and suction piping, which is required for priming on suction lift installations. 7. Install a gate valve and union in the suction and discharge lines. For removal of the pump for service, close the gate valve and disconnect the union. Do not use a globe valve or other restricting type of valve at the discharge. This will seriously restrict the capacity of the pump.. Gauges - Properly sized vacuum or pressure gauges can be installed in both the suction and discharge pipe. The gauges will enable observation of the pump s performance as well as detecting cavitation, vapor binding or other unstable operation. Use only components that are rated higher than shut-off pressure of the system. Do not exceed the pump s maximum case pressure as listed in the following table. Models CJ0/EL0 CJ0/EL0 Maximum Case 00 PSI 60 PSI A pressure relief valve of adequate capacity must be installed on any installation where the pump pressure can exceed the pressure tank s maximum working pressure or on systems where the discharge line can be shut-off or obstructed. Not providing a relief valve can cause extreme over pressure which could result in personal injury and/or property damage. ELECTRICAL Hazardous voltage. Can shock, burn or cause death. Failure to follow warnings can cause fatal or severe shock hazard or equipment failure. Ground motor before connecting to electrical power supply. Connect the motor frame to equipment grounding conductor by using green screw. Do not connect green ground wire to any of the motor leads. line. Do not ground to a gas supply Turn off power to motor before working on electrical connections. Supply voltage must be within ±0% of nameplate voltage. If in doubt consult a licensed electrician. Use wire size specified in wiring Chart E. If possible, connect pump to a separate branch circuit with no other appliances on it. If wiring diagram on motor model plate differs from diagram shown in figures, & 0, follow diagram on motor. All wiring should be performed by a qualified electrician and in accordance with the national and local electric codes. WIRING. Motor voltages will vary depending upon the motor horsepower and phase. Refer to the motor nameplate and the Motor Data Chart (Chart C) for voltage and electrical data. Make certain that the power supply conforms to the electrical specifications of the motor supplied. Failure to do so may cause premature motor failure and will void the warranty.. To change voltage, remove the rear access cover, which is held in place with two () screws. For proper electrical connection, refer to the connection diagram located on the motor nameplate or figures,, 0, &. Replace rear access cover before starting or operating pump. Failure to do so can result in personal injury. MOTOR PROTECTION. All single phase motors have built in thermal protection for all voltages. The overload protects the motor against burnout from overload of low voltage, high voltage and other causes. The device is automatic and resets itself once the temperature has dropped to a safe point. Frequent tripping of the device indicates trouble in the motor or power lines and immediate attention is needed. Never examine, make wiring changes or touch the motor before disconnecting the main electrical supply switch. The thermal device may have opened the electrical circuit.. Three phase motors do not have a built in thermal protection. It is recommended that a properly sized magnetic or manual starter (both with properly sized heaters) be used with all three phase motors. Install starters following instructions of the starter manufacturer. See Figure for magnetic starter wiring diagram.. All motors (single and three phase) should be equipped with a correctly fused disconnect switch to provide protection. consult local or national electric codes for proper fuse protection based on motor data chart (see Charts C & D). 7 Copyright 0. All rights reserved.

GRAYREDTANYELLOWGRAYREDTANFigure - Wiring Diagram for Single Phase /- HP ELLOWIL00YBLACKREDWHITEGRA5 VOLT SINGLE PHASE 0 VOLT SINGLE PHASE Phase Phase L WHITEA B L L WHITEA B L IL0 LOW VOLTAGE 6 5 7 HIGH VOLTAGE 6 5 7 HIGH VOLTAGE BROWN (0) VIOLET () BLACK () YELLOW () BLUE () BROWN (0) VIOLET () YELLOW () BLACK () BLUE () LOW VOLTAGE 0 VOLT SINGLE PHASE Figure - Wiring Diagram for Franklin Electric TEFC Phase and Phase motors Phase GRAYYFigure A - Wiring Diagram for Three Phase HP GROUND (WHEN REQ) LOW VOLTAGE T6 T5 T T T T7 HIGH VOLTAGE T6 T5 T IL60 T6 T T7 T5 T T T T T T T T T7 T T T YELLOWL L LOW VOLTAGE 0V -ø HIGH VOLTAGE 60 V IL 5 6 5 6 Figure - Wiring Diagram for Marathon TEFC Phase motors 7 7 IL0770 L LOW VOLTAGE 6 5 Phase L L L L L Figure - Wiring Diagram for Three Phase HIGH VOLTAGE 6 5 #0 or Heavier Copper Ground Wire, Connect to 0 Ft. Ground Rod or Well Casing Switch V L L L M W Fused Disconnect Switch Lightning Arrestors 7 T T X T 7 T Motor T IL Figure 0 - Wiring Diagram for Baldor TEFC Phase motors Copyright 0. All rights reserved. Ground IL00 Figure - Magnetic Starter Wiring Diagram Three Phase

PRIMING. Before starting any centrifugal pump, it is absolutely necessary that both the casing and suction pipe be completely filled with liquid. This priming can be accomplished by any of the following methods:. When the liquid supply level is above the center line of the pump, it is primed by opening the suction and discharge valves. The inflowing liquid will displace the air and fill the suction line, pump casing, and discharge line up to the level of supply.. Where the pump is operating with suction lift and the suction line is equipped with a foot valve, remove the priming plug from the discharge tee (see Figures 5-) and fill the pump body and suction pipe completely with water. No additional water will be needed for subsequent start-ups unless the pump body is drained.. After the pump is turned on it will require -5 minutes before all air is evacuated from the suction line and water begins to flow. If there is no water after 5 minutes, turn the pump off and check the following: 5. Any air leaks on the suction line must be eliminated. 6. Suction pipe inlet should be a minimum of 5 feet below the water level. 7. Total suction lift cannot be greater than 5 feet.. Any restrictions in the discharge pipe, such as a closed valve must be eliminated. NOTE: Unit must be full of liquid before operating. Never run dry, or against a closed discharge. Dry running or running unit against a closed discharge will cause damage to the shaft seal. Do not pump dirty water or abrasive liquids, otherwise the same may occur as if running dry. MOTOR ROTATION. Single phase models are one () rotation only (counterclockwise when facing the pump suction tapping) and cannot be reversed.. Proper rotation of pump impeller is critical for three phase pumps. Pump motor should turn counterclockwise (CCW) when facing pump suction tapping. Momentarily bump (apply power for less than a second) the motor to check for proper rotation. To change rotation on three phase units, interchange any two () incoming line (power) leads. Figure - Correct Motor Rotation MAINTENANCE Lubrication IL06 The pumps and motors require no lubrication. The ball bearings of the motor have been greased at the factory. Under normal operating conditions they should require no further greasing. Winterizing your Pump Cracked pump housings caused by freezing are not covered by warranty. To protect your pump from freezing, for best results remove the pump and store in a warm environment. If pump cannot be removed from your system, remove both drain plugs, one on the suction flange and one at the bottom rear of the pump (see fig in the instructions.) Allow the water to completely drain from the pump. Re-install both drain plugs and fill pump with RV type antifreeze. Antifreeze also acts as a rust inhibitor. It will help keep rust build up to a minimum and seals lubricated inside the pump while it is not in use. ROTARY SEAL ASSEMBLY REPLACEMENT Disassembly When disassembling the pump, care should be taken not to damage the gaskets. If torn or damaged, replace with new gasket (see parts list).. Remove the four () pump through bolts that connect the mounting ring to the pump body. Remove the pump body, taking care not to damage the gasket or o-ring.. Remove the impellers. CJ0/EL0 Models are single stage units, having one impeller. Using a /6 open end wrench, hold the motor shaft flat and unthread the impeller by turning it counterclockwise. The motor shaft flat area is located in the middle of the mounting ring.. CJ0/EL0 models are multi stage units, having two or more impellers and one or more intermediate stages. Using an /6 open end wrench on the motor shaft extension flat, remove the first impeller by turning or counterclockwise. Remove the intermediate stage (stages) taking care not to damage the gasket (gaskets) and unthread the remaining impellers. Copyright 0. All rights reserved.

. Remove the mechanical seal assembly. The rotary portion of the seal assembly (carbon ring, Buna-N gasket and spring) will easily slide off the end of the shaft. The ceramic portion can be pried out of the rubber seating using two () screwdrivers (see Figure 5). Reassembly The precision lapped faces of the mechanical seal are easily damaged. Handle the replacement seal carefully. Short seal life will result if seal faces (ceramic & carbon) are nicked, scratched or dirty.. Clean the seal cavity of the mounting ring and the motor shaft thoroughly.. Apply liquid soap (one drop only) to the outside of the Buna-N gasket that houses the ceramic seal seat. With thumb pressure, press the ceramic seat, polished face up, squarely into the seal cavity (see Figure 6).. If seal does not seat squarely, remove and reclean the seal cavity. Place a cardboard washer over the polished seal face and carefully press into place using a piece of pipe or tubing (see Figure 7). Discard cardboard washer.. Apply liquid soap (one drop only) to the inside diameter of the rubber drive ring. Slip rubber drive ring (carbon face down) and the spring over the shaft. 5. Reassemble the pump by following the reverse order of the disassembly instructions. MOTOR REPLACEMENT. Nema J motors can be replaced in the field with any standard Nema J jet pump motor by referring to the following instructions and the attached parts list.. Follow steps as outlined under Rotary Seal Replacement to remove the pump body, diffuser, impeller and rotary seal.. Remove bolts that connect the motor to the mounting ring and pull motor away.. Replace motor with standard Nema J jet pump motor by positioning motor against the mounting frame and assembling with four () / x / cap screws. The mounting base is connected at the bottom of the mounting frame with two () / x / cap screws. 5. Follow steps of Rotary Seal Assembly to reassemble the remainder of the pump. BECAUSE DAMAGE TO THE SHAFT SEAL IS MOST LIKELY TO OCCUR IN DISASSEMBLY, A NEW SEAL WILL BE NECESSARY. Cardboard Washer Protects Seal Face Seal Seal Cavity IL055 Figure 5 - Remove Mechanical Seal Figure 6 - Press in Seal Figure 7- If Necessary, Press with Cardboard and Pipe 0 Copyright 0. All rights reserved.

Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Little or no. Pump not primed. Prime unit discharge. Total head too high. Shorten suction lift and/or discharge head. Suction head higher than pump. Lower pump inlet designed for. Impeller clogged. Clean 5. Incorrect rotation 5. Refer to wiring information 6. Leak in suction line 6. Repair or replace 7. Inadequate foot valve 7. Make needed adjustments. Impeller damaged. Replace. Foot valve or suction line not. Submerge lower in water submerged deep enough in water 0. Insufficient inlet pressure or suction head 0. Increase inlet pressure by adding more fluid to fluid source. Wrong size piping. Make needed adjustments. Casing gasket leaking. Replace gasket. Suction or discharge line. Open valves closed Loss of suction. Air leak in suction line. Repair. Suction head too high. Lower pump inlet. Insufficient inlet pressure or suction head. Increase inlet pressure by adding more fluid to fluid source. Clogged foot valve or strainer. Clean or replace Pump vibrates. Mounting plate or foundation. Reinforce and/or makes excessive noise not rigid enough. Foreign material in pump. Clean. Damaged impeller. Replace. Cavitation present. Check suction line for proper size and be certain valve is open. Remove excessive loops in suction line 5. Worn motor bearings 5. Replace 6. Bent impeller shaft 6. Replace Pump will not start. Improperly wired. Refer to wiring diagram or run. Blown fuse or open circuit. Replace fuse or close circuit breaker breaker. Loose or broken wiring. Tighten connections and replace broken wiring. Impeller clogged. Clean 5. Motor shorted out 5. Replace Pumps leaks at shaft. Worn mechanical seal. Replace. Bent impeller shaft. Replace Copyright 0. All rights reserved.

FORM NO. FW00 066 SUPERSEDES 06 CENTRIFUGAL PUMP REPAIR PARTS CJ0/EL0 SERIES (For Pricing Refer To Repair Parts Price List) 5A 5B 7 5 6 0 IL07 ITEM SINGLE PHASE BRASS IMPELLER THREE PHASE BRASS IMPELLER SINGLE PHASE PLASTIC IMPELLER THREE PHASE PLASTIC IMPELLER DESCRIPTION Motor, Nema J - PH Motor, Nema J - PH Motor Access Cover Screws, Access Cover HP / / / -/ STAGE MODEL NO. PART NO. 00R 00 CJ00 CJ0P0 EL0P0 J0 CJ005 EL005 CJ007 EL007 CJ00 EL00 CJ05 EL05 CJ00 EL00 CJ005 CJ007 CJ00 CJ05 CJ00 CJ0P05 EL0P05 CJ0P07 EL0P07 CJ0P0 EL0P0 CJ0P5 EL0P5 CJ0P0 CJ0P05 CJ0P07 CJ0P0 CJ0P5 CJ0P0 J05 J05 J07 J07 QTY. J0 J0 J5 J5 J0 J0 5 5A 5B 6 Slinger Washer Mounting Ring Hex Hd. Cap Screws / x / Seal, Rotary w/spring Impeller - Brass Impeller - Plastic Clearance Ring Ring, Square Cut 605 07 * 00 5 00 6 600 705 00 0 70 5 0 706 07 0 7 7 Body Assembly - Brass Impeller Body Assembly - Plastic Impeller Suction Clearance Ring-Brass Pipe Plugs, / NPT 0 * 770 76A 770 76A 770 770 770 770 0 Hex Hd. Cap Screws / x Base * 555 (*) Standard hardware item () Not shown ( ) For pumps with paper gasket, replace with part number 77 ( ) Kit Includes: Access Cover, Screws & Wiring Diagrams Copyright 0. All rights reserved.

FORM NO. FW000 066 SUPERSEDES 0 CENTRIFUGAL PUMP REPAIR PARTS CJ0, EL0 SERIES (For Pricing Refer To Repair Parts Price List) 5 6 7 6 0 Square Cut Ring Detail of Intermediate Stage Assembly IL05 ITEM SINGLE PHASE - BRASS IMPELLER HP / -/ STAGE CJ0B07 CJ0B0 EL0B0 CJ0B5 EL0B5 CJ0B0 EL0B0 CJ0C0 EL0C0 CJ0C0 EL0C0 THREE PHASE - BRASS IMPELLER MODEL CJ0B07 CJ0B0 CJ0B5 CJ0B0 CJ0C0 CJ0C0 NO. SINGLE PHASE - PLASTIC IMPELLER CJ0P07 CJ0P0 EL0P0 CJ0P5 EL0P5 CJ0P0 EL0P0 CJ0D0 EL0D0 CJ0D0 EL0D0 THREE PHASE - PLASTIC IMPELLER CJ0P07 CJ0P0 CJ0P5 CJ0P0 CJ0D0 CJ0D0 DESCRIPTION PART NO. QTY Motor, Nema J - PH Motor, Nema J - PH Motor Cover w/screws Screws, Cover 00R 00 J07 J07 J0 J0 J5 J5 J0 J0 J0 J0 J60 05 5 6 6 7 Slinger Washer Shaft Mounting Ring Hex Hd. Cap Screws / x / Seal, Rotary w/spring Impeller, Brass Impeller, Thermoplastic Spacer, Shaft Gasket Intermediate Stage Assy-Brass** Intermediate Stage Assy-Plastic** Suction Clearance Ring Hub Clearance Ring Square Cut Ring Interm. Stg. 605 50 * 00 0 06 B 005 057 000 57A 50 5 57A 5 7 57A 600 0 57A 60 7 66A 6 *** 66A 65 0 0 0 Suction Flange Assembly-Brass Suction Flange Assembly-Plastic Suction Clearance Ring Suction Bearing 57A 00 057 0005 Pump thru Bolts (Grade 5) / x -/ Pump thru Bolts (Grade 5) / x 5 Base w/ Bolts / x -/ /" NPT Plug * 0005 * -- -- -- -- -- -- (*) Standard hardware item ( ) For quantity required See number of stages () Not shown (**) Includes two castings, square cut ring, suction and hub clearance ring - See Detail Drawing (***) Includes seal ring and impeller ( ) Kit Includes: Access Cover, Screws & Wiring Diagrams Copyright 0. All rights reserved.