K-86 ERIE OT ATER ANITIZING MULTIPLE-TANK RACK CONVEYOR AREAER Meiko's K-86 rack conveyor warewasher combines stateof-the-art advanced features with economical and reliable operation. Powerful P wash and recirculating rinse pumps, combined with computer-positioned wash arms with varying spray angles and offset jets, ensure outstanding water coverage and consistent cleaning. ash and recirculating rinse arms are pre-assembled into easilyremoved manifolds, and feature slotted, concave nozzles (which minimize clogging) and captivated end caps (which can t be lost during cleaning). Other standard features include fully automatic operation, double-wall insulated construction, a unique external leveroperated drain system, low voltage control circuit, and standard vent cowls with double curtains to reduce splashout. As with all products synonymous with the name Meiko, engineering excellence, manufacturing quality and performance come to the forefront in the K-eries rack conveyors. Exclusive Features: ynchronized side-drive dual rack rail pawl-bar system ensures complete water coverage from every angle, even the bottom of the rack Large, insulated front are spring-loaded to open easily and TAY open, without latching Computer-positioned wash and recirculating rinse arms in easily-removed manifolds. Manifolds are stainless steel with a unique interlock system to eliminate high-wear O- rings Concave, slotted nozzles minimize clogging. Nozzles are computer-positioned at varying angles to maximize water coverage over all areas of the ware Powerful hp wash and recirculating rinse pumps are 50% more powerful than the industry standard for outstanding cleaning Large separation between recirculating rinse and final rinse (4 upper, 5 lower) avoids splashing of soiled water onto sanitized ware Front-sloping tanks for complete drainage and easier cleaning External, easily-operated lever drain system makes draining fast, safe and simple Options: Choice of two s (standard 8 or high hood 6 ) Internal booster heater (steam or electric heat) External booster heater (steam or electric heat) Master disconnect External vent fan control limit switch collars 90 loaders and power unloaders Flanged feet rain water tempering kit hock arrestor tandard Features: Capacity 77 racks per hour ater consumption, standard- machines (K-86E, K-86) - 07.8 U.. gallons per hour - 0.9 U.. gallons per rack ater consumption, high-hood machines (K-86ET, K-86T) - 0.0 U.. gallons per hour - 0.8 gallons per rack All 04-series stainless steel construction ouble-wall insulated construction on front, top and back to improve operator safety, conserve heating energy, and reduce noise and heat loss into the dishroom Large, easily-removed pan strainers with separate prewash scrap basket Fully automatic operation including auto-fill and auto-start. Prewash, wash, recirculating rinse and final rinse are activated only when a rack is in place to conserve water and detergent Powerful hp wash and recirculating rinse pumps. All pumps are vertically-mounted to be self-draining and easily removed for servicing Electromechanical controls for reliability and easy operation. Low-voltage 4VAC control circuit for operator safety Easily accessible detergent and rinse aid injection ports for fast and easy chemical dispenser installation ingle-point electrical, water and drain connections. Internal booster heater option adds an additional terminal block for simpler replacement of an existing external booster heater Low-level heater protection Models: K-86E: 8 vertical, electric heat K-86: 8 vertical, steam coil heat K-86ET: 6 vertical, electric heat K-86T: 6 vertical, steam coil heat on select models K-86 eries Updated 5-08 Meiko (65) 99-6600 (800) 55-MEIKO FAX (65) 99-660 www.meiko.us
K-86 ERIE, LEFT-TO-RIGT OPERATION, ITOUT INTERNAL BOOTER EATER (0mm) orizontal ' 8-/" (50mm) (78mm) open 4 ' 0" (44mm) 4-/ (mm) rain 9-/ 0-/ 6-/" (4mm) (67mm) (65mm) ash section rain Electrical connection 5 -/" (90mm) 7-/" (89mm) 8" (0mm) 0 (559mm) 7 8-/ (50mm) 5-/" 5" (40mm) (7mm) irection -to-table 7' " (84mm) collar centerline 7 0 (88mm) 8 6 (59mm) -/8" (586mm) 8-/8" (05mm) 4-/8" (0mm) " (5mm) / (0mm) ' -/ (74mm) ' ' 8-/" ' 6-/ (5mm) (768mm) ' -/" (95mm) Variable imensions All dimensions from floor are +/- /" due to adjustable feet. 4 5 tandard : ' 6" (457mm) Tall hood option: ' (660mm) ash section tandard : 4' 9-7/8" (47mm) Tall hood option: 5' 5-7/8" (67mm) open tandard : 6' 7-7/8" (00mm) Tall hood option: 7' -7/8" (45mm) tandard : 5' 9-/8" (756mm) Tall hood option: 6' 5-/8" (45mm) Electrical connection AFF tandard : 5' (66mm) Tall hood option: 6' (89mm) K-86 ERIE, RIGT-TO-LEFT OPERATION, ITOUT INTERNAL BOOTER EATER (0mm) orizontal ' 8-/" (50mm) (78mm) open 4 4-/ (mm) rain 0-/ 9-/ (67mm) (4mm) 6-/" (65mm) (44mm) ' 0" ash section rain Electrical connection 5 ' 6-/ (768mm) ' -/ (74mm) ' -/" (95mm) 8-/8" (05mm) 4-/8" (0mm) / " (5mm) (0mm) ' ' 8-/" (5mm) 5-/8" (05mm) 5-/" (40mm) irection 5" (7mm) 7 8-/ (50mm) 0 (559mm) -/" (90mm) Variable imensions All dimensions from floor are +/- /" due to adjustable feet. tandard : ' 6" (457mm) Tall hood option: ' (660mm) ash section tandard : 4' 9-7/8" (47mm) Tall hood option: 5' 5-7/8" (67mm) open tandard : 6' 7-7/8" (00mm) Tall hood option: 7' -7/8" (45mm) 4 tandard : 5' 9-/8" (756mm) -to-table 7' " (84mm) 8" (0mm) Tall hood option: 6' 5-/8" (45mm) collar centerline 7 0 (88mm) 8 6 (59mm) 5 Electrical connection AFF tandard : 5' (66mm) Tall hood option: 6' (89mm) K-86 eries Updated 5-08 Meiko (65) 99-6600 (800) 55-MEIKO FAX (65) 99-660 www.meiko.us 7-/" (89mm)
K-86 ERIE, LEFT-TO-RIGT OPERATION, IT INTERNAL BOOTER EATER (0mm) orizontal ' 8-/" (50mm) (78mm) 5 9-/8 (756mm) 4 9-7/8 (47mm) 6 7-7/8 (00mm) 6 (457mm) 5 (576mm) ' 0" (44mm) 4-/ (mm) rain 0-/ 6-/" (67mm) (65mm) rain 5 4 (66mm) -/" (90mm) 7-/" (89mm) 0 (559mm) 7 8-/ (50mm) irection (0mm) -/8" (84mm) 5" (7mm) 8-/8" (05mm) 4-/8" (0mm) (0mm) / (0mm) ' -/ (74mm) ' ' 8-/" ' 6-/ (5mm) (768mm) ' -/" (95mm) 8" (0mm) -to-table 7' " (84mm) collar centerline 7 0 (88mm) 8 6 (59mm) K-86 ERIE, RIGT-TO-LEFT OPERATION, IT INTERNAL BOOTER EATER (0mm) orizontal ' 8-/" (50mm) (78mm) 5 9-/8 (756mm) 4 9-7/8 (47mm) 6 7-7/8 (00mm) 6 (457mm) 5 (576mm) 4-/ (mm) rain 0-/ (67mm) 6-/" (65mm) (44mm) ' 0" rain 5 4 (66mm) 8-/8" (05mm) 4-/8" (0mm) (0mm) / (0mm) ' -/ (74mm) ' ' 6-/ ' 8-/" (768mm) (5mm) ' -/" (95mm) -/8 (84mm) -/ (667mm) 5" (7mm) 7 8-/ (50mm) irection 0 (559mm) -/" (90mm) 7-/" (89mm) -to-table 7' " (84mm) collar centerline 7 0 (88mm) 8 6 (59mm) 8" (0mm) K-86 eries Updated 5-08 Meiko (65) 99-6600 (800) 55-MEIKO FAX (65) 99-660 www.meiko.us
K-86 ERIE UTILITY CONNECTION rain -5/6 (75mm) O vertical, gravity-fed drain outlet (PE piping). Recommend placement directly above 4 floor drain. Additional piping to drain (if so required) to be supplied by customer. Connection is (44mm) AFF. If using optional NPT adapter, connection is 8-/ (4mm) AFF. Refer to etail View: rain for suggested connection. ingle electrical connection - machines without internal booster heater ingle terminal block inside control box (4-wire with ground - no neutral). ual electrical connections - machines with internal electric booster heater Two terminal blocks inside control box (4-wire with ground - no neutral). - Machine electrical supply - Booster heater electrical supply Electrical supply (or supplies) should be routed into control box through strain relief(s) on rear of control box. Incoming leads must be appropriately sized for electrical supply. Individual disconnect with lockout/tagout strongly (provided by customer). Connection for standard- machines is 5 4 (66mm) AFF. Connection for tall hood machines is 6 (89mm) AFF. Refer to utility chart on Page 5 for electrical load information. Vent connection - machines with optional vent cowl collars Refer to etail View: Vent for suggested connection. The waste air connection must be corrosion-resistant and frost-free. In particular, provisions must be made to prevent air temperatures of F/0 C or colder from reaching the machine at any time. A provision for draining moisture from the waste air pipe is strongly. Load end - 00 CFM Unload end - 50 CFM Total - 550 CFM ot water connection - machines without internal booster heater / NPT female pipe connection is 9-/ (4mm) AFF. Temperature 80 F (8 C) Pressure 5-5 PI Initial fill 58. U.. gals. (0. liters) Consumption: Refer to utility chart on Page 5 Recommended hardness -6 grains/u.. gal. ater connection - machines with internal booster heater only / NPT female pipe connection is 9-/ (4mm) AFF. Temperature: Machines with 40 F booster: 40 F (60 C) Machines with 70 F booster: 0 F (4 C) Pressure 5-5 PI Initial fill 58. U.. gals. (0. liters) Consumption: Refer to utility chart on Page 5 Recommended hardness -6 grains/u.. gal. team connection - steam-heated machines / NPT male pipe connection is 0-/ (67mm) AFF. Pressure 0-0 PI. Consult factory if steam pressure is below 0 PI. If pressure is above 0 PI, use of a regulator is REQUIRE (supplied by customer). Consumption: Refer to utility chart on Page 5 Condensate return connection - steam-heated machines / NPT male pipe connection is 0-/ (67mm) AFF. Condensate line MUT be pressure-free. ETAIL VIE: VENT Machines equipped with optional vent cowl collars may be installed underneath a ventilation hood, or may use pant leg ventilation ducts (to be supplied by the customer). To determine the dimensions of the duct, first determine how they will be installed: uct sleeved outside collar Inside dimensions of duct: 4 x 6 (0 x 406mm). uct sleeved inside collar Outside dimensions of duct: -/4 x 5-/4 (95 x 400mm). The duct must not interfere with the adjustable baffle, as shown. Adjustable baffle uct sleeved outside collar () 4 x 6 (0x406mm) inside dimensions " (50mm) max. uct sleeved inside collar (if required) -/4 x 5-/4 (95x400mm) outside dimensions / (mm) max. ETAIL VIE: RAIN The machine is equipped with a -5/6" (75mm) O vertical, gravity-fed drain. If possible, the machine drain can simply be positioned directly above a floor drain. If a floor drain is not in the correct location, or if local codes require a trap, a " indirect drain line may be attached using the supplied boot, clamp, and " NPT male adapter. Choose a piping material that: Complies with any applicable local and national codes Is rated for use with water temperatures up to 80 F/8 C Is rated for - p to accommodate detergents and rinse aid in the drain water 9-5/8 (44mm) 8-/ (4mm) Optional NPT adapter ETAIL VIE: TABLING Check that the table lip overlaps BOT the inner and outer s. Use silicone sealer between the table lip and the machine to prevent leakage. top AFF Outer (with support lip) Feeding and discharge tables to be supplied by others Outside view Inner 0-/" (5mm) max. opening for table lip Outer (with support lip) Inside view turndown flange maximum / (9mm) Inner K-86 eries Updated 5-08 Meiko (65) 99-6600 (800) 55-MEIKO FAX (65) 99-660 www.meiko.us
K-86 eries Technical pecifications Operating Capacities (NF Rated) Racks per hour... 77 ishes per hour... 695 Glasses per hour... 997 Conveyor pecifications Conveyor belt speed... 7 8 (.m)/min. orizontal... 8-/ (50mm) (K-86E, K-86)... 6 (457mm) (K-86ET, K-86T)... (660mm) Venting pecifications Load end... 00 CFM (6m /h) Unload end... 50 CFM (588m /h) Total... 550 CFM (94m /h) hipping Information K-86E, K-86: Machine weight... 849 lbs. (85kg) hipping weight... 948 lbs. (40kg) Crating (Lxx)... 9 x x 6 (.8 x 0.9 x.9m) 70. cu. ft. (4.8m ) K-86ET, K-86T: Machine weight... 949 lbs. (4kg) hipping weight... 048lbs. (476kg) Crating (Lxx)... 9 x x 6 (.8 x 0.9 x.m) 88.5 cu. ft. (5.m ) ater pecifications Minimum water temperatures: Prewash tank... 0-40 F (4-60 C) ash tank... 50 F (66 C) Recirculating rinse tank... 60 F (7 C) Final rinse... 80 F (8 C) Minimum incoming water temperature: Machines without internal booster... 80 F (8 C) Machines with internal booster... 0 or 40 F (4 or 60 C) Initial fill... 58. U.. gals. (0. liters) Prewash tank capacity... 7. U.. gals. (65. liters) ash tank capacity... 0.5 U.. gals. (77.6 liters) Recirculating rinse tank capacity... 0.5 U.. gals. (77.6 liters) Incoming water line size... /4 NPT Recommended water hardness... -6 grains/u.. gal. Consumption at 00% capacity: K-86E, K-86.... 07.8 U.. gals. (408.0 liters)/hr. 0.9 U.. gals. (.47 liters)/rack K-86ET, K-86T.... 0.0 U.. gals. (870.6 liters)/hr. 0.8 U.. gals. (.4 liters)/rack Final rinse flow pressure... 5-5 PI (.0-.7 bars) Flow rate (K-86E, K-86)....80 U.. gals.(6.80 liters)/min. Flow rate (K-86ET, K-86ET)....8 U.. gals.(4.5 liters)/min. Electrical pecifications Machine supply Peak Minimum Maximum connection current supply circuit breaker/ draw ampacity disconnect K-86E (standard electric tank heat) 08V/60 z/ Ph 88. A 0 A 5 A 0V/60 z/ Ph 80. A 0 A 00 A 460V/60 z/ Ph 9.7 A 55 A 50 A K-86ET (tall hood, electric tank heat) 08V/60 z/ Ph 88. A 0 A 5 A 0V/60 z/ Ph 80. A 0 A 00 A 460V/60 z/ Ph 9.7 A 55 A 50 A K-86, K-86T (standard and tall hood, steam coil tank heat) 08V/60 z/ Ph.5 A 40 A 0 A 0V/60 z/ Ph.6 A 40 A 0 A 460V/60 z/ Ph 9.6 A 5 A 5 A Internal booster heater Rating, Rating, Peak Minimum Maximum supply connection machine machine current supply circuit breaker/ startup operation draw ampacity disconnect 40 F rise electric booster (40 F/60 C water supply temperature) 08V/60 z/ Ph 4.4 k 9.6 k 40.0 A 55 A 50 A 0V/60 z/ Ph 4.4 k 9.6 k 6. A 55 A 50 A 460V/60 z/ Ph 4.4 k 9.6 k 8. A 0 A 5 A 70 F rise electric booster (0 F/4 C water supply temperature) 08V/60 z/ Ph 8.8 k.6 k 79.9 A 0 A 00 A 0V/60 z/ Ph 8.8 k.6 k 7. A 0 A 00 A 460V/60 z/ Ph 8.8 k.6 k 6. A 55 A 50 A Electric tank heat: ash tank 08V/60z/Ph 0V/60z/Ph 460V/60z/Ph K-86E 5.0 k 4.6 k 5.0 k K-86ET 5.0 k 4.6 k 5.0 k Recirc. rinse tank 08V/60z/Ph 0V/60z/Ph 460V/60z/Ph K-86E 9.0 k 8.8 k 9.0 k K-86ET 9.0 k 8.8 k 9.0 k Prewash pump motor... 0.75 hp ash pump motor....0 hp Recirculating rinse pump motor....0 hp Conveyor motor... 0.5 hp team pecifications (K-86, K-86T) team line connection... /4 NPT Condensate return connection... /4 NPT team pressure... 0-0 psi (0.7-.0 bars) Consumption: K-86... 60 lbs./hr. K-86T... 60 lbs./hr. Internal team Booster eater: 40 F rise steam booster (40 F/60 C water supply temperature)... 50 lbs./hr. 70 F rise steam booster (0 F/4 C water supply temperature)... 00 lbs./hr. External Booster eater Recommendations (for machines without optional internal booster heater) Booster ratings are based on peak capacity of 07.8 U.. gals/hr. and a flow rate of.80 U.. gals./min. for models K-86E and K-86; peak capacity of 0.0 U.. gals./hr. and a flow rate of.8 U.. gals./min. for models K-86ET and K-86T. Recommended boosters are one size larger than required to help compensate for any local conditions that may prevent full performance. ater supply Required Recommended temperature temperature rise booster rating K-86E, K-86 0 F/4 C 70 F/9 C 7 k 40 F/60 C 40 F/ C 5 k K-86ET, K-86T 0 F/4 C 70 F/9 C 45 k 40 F/60 C 40 F/ C 7 k K-86 eries Updated 5-08 Meiko (65) 99-6600 (800) 55-MEIKO FAX (65) 99-660 www.meiko.us
Equipment pecification: K-86 Rack Conveyor arewasher - Item No. Item will be a K-86 multiple-tank, rack conveyor dishmachine, consisting of a prewash zone with a /4 hp pump motor, a wash zone with a hp pump motor, a recirculating rinse zone with a hp pump motor, and a final rinse zone. Total length of the tank section (not including vent cowls) will be 7 (85mm). Unit will utilize a 80ºF/8 C minimum fresh water sanitizing rinse. Unit will have a capacity of 77 racks per hour at an NF-rated belt speed of 7 8 (.m) per minute. tandard- units will consume an NF-rated 07.8 U.. gals./408.0l per hour (0.9 U.. gals./.47l per rack). Tall-hood units will consume an NF-rated 0.0 U.. gals./870.6l per hour (0.8 U.. gals./.4l per rack). The dishmachine will be NF, UL and CUL listed. Electrical characteristics: 08V/60 z/ Ph 0V/60 z/ Ph 460V/60 z/ Ph ash tank temperature will be maintained at a minimum of 50 F/66 C. Recirculating rinse tank temperature will be maintained at a minimum of 60 F/7 C. Tank heating will be accomplished by: Thermostatically-controlled electric heating elements (K-86E, K-86ET) Thermostatically-controlled stainless steel steam coils (K-86, K-86T) irection of conveyor travel will be: Right-to-Left Left-to-Right Unit will have the following standard features: ouble-wall, insulated construction on top, front, and rear. Two upper prewash arms and one lower prewash arm. Four upper wash arms with 5 (8mm) wash area and four lower wash arms with 4 (56mm) wash area. Four upper recirculating rinse arms with 5 (8mm) wash area and four lower recirculating rinse arms with 4 (56mm) wash area. ash arm spray pattern ensures effective coverage with varying angles and offset spray jets. lotted, concave wash nozzles and captivated end caps for easier cleaning. Minimum separation between recirculating rinse and final rinse of 4 (56mm) upper and 5 (8mm) lower. Exclusive synchronized rack rail pawl bar system for smooth rack movement. ide drive system provides easy cleaning access and eliminates wash pattern obstruction. Front-sloping tanks for complete tank drainage, accessibility, and cleanability. Fully automatic operation including auto-fill and auto-start. eparate compartment actuator switches to ensure prewash, wash, recirculating rinse and final rinse are energized only when a rack is in place. External, easily operable, lever-operated drain system. Low level heater protection. Prewash, wash and recirculating rinse pump motors are self-draining, internal and vertically installed for easy access and serviceablity. Pump housing and impeller constructed of stainless steel. Totally electromechanical controls with a 4 VAC control circuit. ingle point electrical connection. Easily removable wash arm and recirculating rinse arm block manifold systems, prewash arms and final rinse arms. Large front access can be opened with one hand and remain open without latches, aiding machine accessibility and cleanability. Large, removable stainless pan strainers with separate prewash scrap basket. Built-in pressure regulator. ingle point drain connection. Unit will have the following optional features (check all that apply): Tall hood option to increase vertical from 6 (457mm) to (660mm) Internal booster heater (steam or electric per machine spec). Electrically-heated internal booster heater adds electrical terminal block to machine ( total). ized for a minimum 40 F ( C) rise and 40 F (60 C) ized for a minimum 70 F (9 C) rise and 0 F (4 C) External booster heater ized for a minimum 40 F ( C) rise and 40 F (60 C) ized for a minimum 70 F (9 C) rise and 0 F (4 C) team heated Electrically heated Master disconnect External vent fan control limit switch Inline (whisker switch) style End stop style with adjustable damper 4 x 6 x 7 (0x406x78mm) At both ends At load end only At unload end only 90 side loader (unhooded), long 90 side loader (hooded), long 90 power loader, 4-/4 long 90 power unloader, 4-/4 long Flanged feet for permanent installation rain water tempering kit hock arrestor K-86 eries Updated 5-08 Meiko (65) 99-6600 (800) 55-MEIKO FAX (65) 99-660 www.meiko.us