Throughout standard remove references to the following and replace with the following:

Similar documents
First Revision No. 1-NFPA 30A-2015 [ Section No ] Supplemental Information. Submitter Information Verification. Committee Statement

Public Comment No. 7-NFPA 30A-2013 [ Section No ]


Public Input No. 52-NFPA [ Section No [Excluding any Sub-Sections] ]

Remove the "Exception" text to be consistent with direction provided in the MOS.

Public Input No. 1-NFPA 90B-2015 [ Chapter 2 ]

Resolution: FR-2-NFPA Statement: The new language requires the action completed by NFPA 557 be prepared by a person that is approved.

First Revision No. 2-NFPA [ Global Input ] Submitter Information Verification. Committee Statement. 1 of 11 1/18/2016 5:43 PM

Second Revision No. 5-NFPA [ Section No ] Supplemental Information. Submitter Information Verification. Committee Statement


12/21/2015 National Fire Protection Association Report

Public Input No. 3-NFPA [ Chapter 2 ]

Adobe Connect - Invitation to NFPA 385 Second Draft Web Conference

Public Input No. 1-NFPA 99B-2015 [ Section No. 2.3 ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document

Public Input No. 1-NFPA [ Global Input ] Statement of Problem and Substantiation for Public Input. Submitter Information Verification

Second Revision No. 3-NFPA [ Section No. 2.3 ]

First Revision No. 20-NFPA [ Section No ]

Public Input No. 1-NFPA [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document

TECHNICAL COMMITTEE ON SAFETY AT MOTORSPORTS VENUES. NFPA 610 First Draft Meeting. October 17-18, 2016

Public Comment No. 13-NFPA [ Section No ]

Public Comment No. 23-NFPA [ Section No ] Statement of Problem and Substantiation for Public Comment Related Item

MEMORANDUM. NFPA Technical Committee on Solvent Extraction Plants. NFPA 36 First Draft TC FINAL Ballot Results (F2016)

Public Input No. 88-NFPA [ New Section after ] Statement of Problem and Substantiation for Public Input

Public Input No. 1-NFPA [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document

Public Input No. 1-NFPA [ Global Input ] Additional Proposed Changes. Statement of Problem and Substantiation for Public Input

Public Input No. 48-NFPA [ Section No ] Additional Proposed Changes. Statement of Problem and Substantiation for Public Input

MEMORANDUM. According to the final ballot results, all ballot items received the necessary affirmative votes to pass ballot.

Committee on NFPA 30A

Second Revision No. 1-NFPA 90A-2016 [ Section No ] Submitter Information Verification. Committee Statement


Change all instances of "flame resistant (hypobaric)" to "Limited-Combustible (material)" in all instances in the document.

First Revision No. 2-NFPA 90B-2012 [ Section No. 1.3 ] Submitter Information Verification. Committee Statement and Meeting Notes

First Revision No. 1-NFPA [ Chapter 2 ]

Page 1 of 6 10/19/2016 9:49 AM. Public Input No. 4-NFPA [ Section No ] Statement of Problem and Substantiation for Public Input

Throughout standard remove references to the following and replace with the following:

MEMORANDUM. NFPA 51 First Draft Technical Committee FINAL Ballot Results (A2017 Cycle)

TECHNICAL COMMITTEE ON AUTOMOTIVE and MARINE SERVICE STATIONS

Standard Compared 2012 Changes of the International Building Code and National Fire Protection Association- 101

NFPA 37 Public Comment Responses Page 1 of 32

NFPA 101 SAF-RES PUBLIC COMMENTS


First Revision No. 49-NFPA 17A-2015 [ Detail ] Submitter Information Verification. Committee Statement 7/30/2015 1:35 PM

Second Revision No. 1 NFPA [ Chapter 2 ]

Public Comment No. 2-NFPA [ Section No ]

NFPA 30 FLC-FUN Public Inputs Page 1 of 26. Public Input No. 5-NFPA [ Section No. 2.3 ] 11/6/2015 7:41 AM



Public Comment No. 1-NFPA [ Section No ]

Committee on NFPA 51A

Committee Input No NFPA [ Global Input ] Submitter Information Verification. Committee Statement. 1 of /20/ :02 AM

Riverside County Fire Department Office of the Fire Marshal Market St., Ste. 150, Riverside, CA Ph. (951) Fax (951)


M E M O R A N D U M. According to the final ballot results, all ballot items received the necessary affirmative votes to pass ballot.

Second Revision No. 1-NFPA 17A-2016 [ Section No ] Submitter Information Verification. Committee Statement. 1 of 14 6/22/2016 3:15 PM

BUILDING/FIRE CODE REFERENCES 2006 EDITION

Committee Input No. 60-NFPA [ Sections , ]

Public Input No. 4-NFPA [ Section No ] Statement of Problem and Substantiation for Public Input. Submitter Information Verification

Public Input No. 1-NFPA [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document

Technical Committee on Record Protection (REA-AAA)


Second Revision No. 36-NFPA [ Detail ] Submitter Information Verification. Committee Statement 5/18/2015 1:01 PM

A NATIONAL SET OF HYDROGEN CODES AND STANDARDS FOR THE US

ARTICLE 25. FUEL GAS CODE

Above Ground Fuel Tank Requirements

First Revision No. 6-NFPA 90A-2012 [ Chapter NFPA ] Submitter Information Verification. Committee Statement and Meeting Notes

M E M O R A N D U M. NFPA Technical Committee on Alternative Approaches to Life Safety. SUBJECT: NFPA 101A ROP TC Letter Ballot (A2012 Cycle)

SAF-BCF SECOND REVISIONS WITH STATEMENTS

Public Input No. 16-NFPA [ Section No ] Additional Proposed Changes. Statement of Problem and Substantiation for Public Input

2018 IFC Update. Based on the 2018 International Fire Code, (IFC ) Goal. Objectives. Content

NFPA 30 FLC-SWC First Revisions Page 1 of 10 11/6/2015 9:21 AM. First Revision No. 208-NFPA [ Section No ]

FIF AAA (F2014) Second Draft Meeting Web/Teleconference Meeting Agenda March 18, :00 5:00 p.m. ET

National Fire Protection Association. 1 Batterymarch Park, Quincy, MA Phone: Fax:

NFPA 77 Public Inputs with Responses Page 1 of 15

1/8/ :02 AM. Public Input No. 2-NFPA [ Section No ] Statement of Problem and Substantiation for Public Input

Second Revision No. 1-NFPA [ Section No. 2.2 ] Submitter Information Verification. Committee Statement

First Revision No. 6-NFPA [ Section No. 2.2 ]

Hydrogen Refueling Code Gap Assessment

First Revision No. 82-NFPA [ Detail ] Submitter Information Verification Submitter Full Name: Organization:

Public Input No. 2-NFPA [Chapter F]

NFPA 30 FLC-SWC Public Comment Report

Technical Committee on Fluidized Bed Boilers

First Revision No. 15-NFPA [ Chapter 2 ]

Changes for the New Edition. Senior Engineer, NFPA NFPA

Public Input No. 4-NFPA [ Section No. 4.2 ] Statement of Problem and Substantiation for Public Input. Submitter Information Verification

6/9/ :58 PM. First Revision No. 1-NFPA [ Section No ] Submitter Information Verification. Committee Statement

WORKING DRAFT OF COMMITTEE MEETING OUTPUT

Subject: BSR Uniform Mechanical Code, 2015 Edition: Appeal on Proposal #333

Reference to the Smoke Damage Index (SDI) is needed as it is part of the test method.

2009 International Fire Code Errata. SECOND PRINTING (Posted April 6, 2010)

Public Comment No. 2-NFPA [ Section No ] Statement of Problem and Substantiation for Public Comment. Submitter Information Verification

FIRE SAFETY DURING CONSTRUCTION, ALTERATION AND DEMOLITION

Plant Processing and Extraction Facilities

Public Input No. 1-NFPA [ Global Input ] Additional Proposed Changes. Statement of Problem and Substantiation for Public Input

First Revision No. 36-NFPA [ Section No. 1.1 [Excluding any Sub-Sections] ]

ERRATA TO THE 2000 INTERNATIONAL FIRE CODE. Fourth Printing, January 2002 Updated March 29, 2002

Public Input No. 107-NFPA [ Section No ] Statement of Problem and Substantiation for Public Input. Submitter Information Verification

Public Input No. 23-NFPA [ Section No. 1.1 [Excluding any


M E M O R A N D U M. Diane Matthews, Administrator, Technical Projects. NFPA 101 First Draft Letter Ballot (A2014)

Transcription:

of 105 1/21/2016 7:49 AM Public Input No. 2-NFPA 30A-2015 [ Global Input ] Throughout standard remove references to the following and replace with the following: (1) ANSI/UL and replace with UL. (2) ANSI Z129.1 and replace with ANSI Z400.1/Z129.1. (3) API # and so on and replace API STD # or API RP #. Referenced recommended updates to correlate with PI-3 and P1-4. Related Public Inputs for This Document Related Input Public Input No. 3-NFPA 30A-2015 [Section No. 2.3] Public Input No. 4-NFPA 30A-2015 [Section No. D.1.2] Relationship Referenced current SDO addresses, standard numbers, names, and years. Referenced current SDO addresses, standard numbers, names, and years. Submitter Full Name: Aaron Adamczyk Organization: [ Not Specified ] Submittal Date: Fri Feb 06 23:51:05 EST 2015 Resolution: A document search may not recognize abbreviations. If a standard has been recognized by ANSI, the group who has created the standard generally wants the document recognized as such and would include ANSI in the designation. The reference should be the full title, not an abbreviation. The Manual of Style should be referenced to ensure compliance with the formatting for references. The ANSI Z129.1 reference is updated in the appropriate annex sections.

of 105 1/21/2016 7:49 AM Public Input No. 39-NFPA 30A-2015 [ Section No. 1.1.3 ] 1.1.3* This code shall not apply to those motor fuel dispensing facilities where only liquefied petroleum gas (LP-Gas), liquefied natural gas (LNG), or compressed natural gas (CNG), or hydrogen is dispensed as motor fuel. NFPA 2, Hydrogen Technologies Code, is not currently recognized in Chapter 1 Administration yet NFPA 2 contains two chapters on hydrogen fueling facilities (i.e. - Chapter 10 GH2 Vehicle Fueling Facilities; and Chapter 11 LH2 Fueling Facilities) as well as a chapter on repair garages servicing hydrogen-fueled vehicles (i.e. - Chapter 18 Repair Garages). These requirements are contained only in NFPA 2 and nowhere else. Previous text in NFPA 52 has been removed. The Standards Council has revised the Scope of NFPA 52 and removed fueling of hydrogen-fuel cell vehicles (FCV). Therefore, fueling requirements for hydrogen are contained in NFPA 2 and the exclusion of section NFPA 30A 1.1.3 should be extended to hydrogen fueling as well as CNG and LPG. Related Public Inputs for This Document Related Input Public Input No. 40-NFPA 30A-2015 [Section No. A.1.1.3] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 17:30:24 EDT 2015 Resolution: FR-1-NFPA 30A-2015 Statement: This change was made to be consistent with the committee scope. Annex: It is appropriate to add the reference to NFPA 2, as hydrogen fueling is also addressed in this code.

of 105 1/21/2016 7:49 AM Public Input No. 5-NFPA 30A-2015 [ Section No. 1.1.3 ] 1.1.3* This code shall not apply to those motor fuel dispensing facilities where only liquefied petroleum gas (LP-Gas), liquefied natural gas (LNG), or compressed natural gas (CNG), or hydrogen is dispensed as motor fuel. NFPA Standard Council has moved all hydrogen requirements from NFPA52 to NFPA2, including those for Motor Fueling Dispensing and Repair Garages. The 2011 version of the NFPA2 code had specific information on Dispensing, but not for Repair Garages (reserved). The 2016 version of NFPA2 will have specific requirements for Repair Garages and will be published prior to NFPA30A. Therefore, in order to prevent conflicting requirements, hydrogen should be excluded from NFPA30A, as is LPG, LNG, and CNG. Related Public Inputs for This Document Related Input Public Input No. 23-NFPA 30A-2015 [Section No. 12.2.3] Public Input No. 76-NFPA 30A-2015 [Section No. A.1.1.3] Relationship Submitter Full Name: Spencer Quong Organization: Quong & Associates Inc. Affilliation: Toyota Submittal Date: Wed Mar 18 13:22:57 EDT 2015 Resolution: FR-1-NFPA 30A-2015 Statement: This change was made to be consistent with the committee scope. Annex: It is appropriate to add the reference to NFPA 2, as hydrogen fueling is also addressed in this code.

of 105 1/21/2016 7:49 AM Public Input No. 41-NFPA 30A-2015 [ Section No. 2.2 ] 2.2 NFPA Publications. National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169-7471. NFPA 2, Hydrogen Technoloigies Code, 2016 edition. NFPA 10, Standard for Portable Fire Extinguishers, 2013 edition. NFPA 13, Standard for the Installation of Sprinkler Systems, 2013 edition. NFPA 14, Standard for the Installation of Standpipe and Hose Systems, 2013 edition. NFPA 30, Flammable and Combustible Liquids Code, 2015 edition. NFPA 31, Standard for the Installation of Oil-Burning Equipment, 2011 edition. NFPA 33, Standard for Spray Application Using Flammable or Combustible Materials, 2011 edition. NFPA 51, Standard for the Design and Installation of Oxygen Fuel Gas Systems for Welding, Cutting, and Allied Processes, 2013 edition. NFPA 51B, Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, 2014 edition. NFPA 52, Vehicular Gaseous Fuel Systems Code, 2013 edition. NFPA 54, National Fuel Gas Code, 2015 edition. NFPA 55, Compressed Gases and Cryogenic Fluids Code, 2013 edition. NFPA 58, Liquefied Petroleum Gas Code, 2014 edition. NFPA 70, National Electrical Code, 2014 edition. NFPA 72, National Fire Alarm and Signaling Code, 2013 edition. NFPA 80, Standard for Fire Doors and Other Opening Protectives, 2013 edition. NFPA 82, Standard on Incinerators and Waste and Linen Handling Systems and Equipment, 2014 edition. NFPA 85, Boiler and Combustion Systems Hazards Code, 2011 edition. NFPA 86, Standard for Ovens and Furnaces, 2015 edition. NFPA 90A, Standard for the Installation of Air-Conditioning and Ventilating Systems, 2015 edition. NFPA 91, Standard for Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Noncombustible Particulate Solids, 2010 edition. NFPA 101, Life Safety Code, 2015 edition. NFPA 211, Standard for Chimneys, Fireplaces, Vents, and Solid Fuel Burning Appliances, 2013 edition. NFPA 220, Standard on Types of Building Construction, 2015 edition. NFPA 253, Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source, 2011 edition. NFPA 326, Standard for the Safeguarding of Tanks and Containers for Entry, Cleaning, or Repair, 2010 edition. NFPA 385, Standard for Tank Vehicles for Flammable and Combustible Liquids, 2012 edition. Adds NFPA 2 2016 edition to list of references. NFPA 2, Hydrogen Technologies Code, is not currently referenced in Section 2.2 NFPA Publications. Terra seems to have added additional underlines but this is the only proposed change.

of 105 1/21/2016 7:49 AM Requirements for hydrogen refueling, hydrogen generation, hydrogen fuel cells, hydrogen-fueled vehicles in parking / repair garages, etc. are contained only in NFPA 2 and nowhere else. Previous text in NFPA 52 has been removed. The Standards Council has revised the Scope of NFPA 52 and removed fueling of hydrogen-fuel cell vehicles. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 18:01:48 EDT 2015 Resolution: FR-23-NFPA 30A-2015 Statement: Added reference to NFPA 2 since it is no longer excluded in Chapter 12.

of 105 1/21/2016 7:49 AM Public Input No. 8-NFPA 30A-2015 [ Section No. 2.2 ] 2.2 NFPA Publications. National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169-7471. NFPA 2, Hydrogen Technologies Code, 2016 edition NFPA 10, Standard for Portable Fire Extinguishers, 2013 edition. NFPA 13, Standard for the Installation of Sprinkler Systems, 2013 edition. NFPA 14, Standard for the Installation of Standpipe and Hose Systems, 2013 edition. NFPA 30, Flammable and Combustible Liquids Code, 2015 edition. NFPA 31, Standard for the Installation of Oil-Burning Equipment, 2011 edition. NFPA 33, Standard for Spray Application Using Flammable or Combustible Materials, 2011 edition. NFPA 51, Standard for the Design and Installation of Oxygen Fuel Gas Systems for Welding, Cutting, and Allied Processes, 2013 edition. NFPA 51B, Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, 2014 edition. NFPA 52, Vehicular Gaseous Fuel Systems Code, 2013 edition. NFPA 54, National Fuel Gas Code, 2015 edition. NFPA 55, Compressed Gases and Cryogenic Fluids Code, 2013 edition. NFPA 58, Liquefied Petroleum Gas Code, 2014 edition. NFPA 70, National Electrical Code, 2014 edition. NFPA 72, National Fire Alarm and Signaling Code, 2013 edition. NFPA 80, Standard for Fire Doors and Other Opening Protectives, 2013 edition. NFPA 82, Standard on Incinerators and Waste and Linen Handling Systems and Equipment, 2014 edition. NFPA 85, Boiler and Combustion Systems Hazards Code, 2011 edition. NFPA 86, Standard for Ovens and Furnaces, 2015 edition. NFPA 90A, Standard for the Installation of Air-Conditioning and Ventilating Systems, 2015 edition. NFPA 91, Standard for Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Noncombustible Particulate Solids, 2010 edition. NFPA 101, Life Safety Code, 2015 edition. NFPA 211, Standard for Chimneys, Fireplaces, Vents, and Solid Fuel Burning Appliances, 2013 edition. NFPA 220, Standard on Types of Building Construction, 2015 edition. NFPA 253, Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source, 2011 edition. NFPA 326, Standard for the Safeguarding of Tanks and Containers for Entry, Cleaning, or Repair, 2010 edition. NFPA 385, Standard for Tank Vehicles for Flammable and Combustible Liquids, 2012 edition. The reference to NFPA2 is missing. In addition, the NFPA Standard Council has moved all hydrogen requirements from NFPA52 to NFPA2, including those for Motor Fueling Dispensing and Repair Garages. The 2011 version of the NFPA2 had specific information on Dispensing, but not for Repair Garages (reserved). The 2016 version of NFPA2 will have specific requirements for Repair Garages and will be published prior to NFPA30A.

of 105 1/21/2016 7:49 AM Submitter Full Name: Spencer Quong Organization: Quong & Associates Inc. Affilliation: Toyota Submittal Date: Wed Mar 18 13:53:16 EDT 2015 Resolution: FR-23-NFPA 30A-2015 Statement: Added reference to NFPA 2 since it is no longer excluded in Chapter 12.

of 105 1/21/2016 7:49 AM Public Input No. 3-NFPA 30A-2015 [ Section No. 2.3 ] 2.3 Other Publications. 2.3.1 API Publications. American Petroleum Institute, 1220 L Street, N.W., Washington, DC 20005-4070. API 607 API STD 607, Fire Test for Soft-Seated For Quarter-Turn Valvees And Valves Equipped With Nonmetallic Seats, 5th 6th edition, June 2005 2010. 2.3.2 ASTM Publications. ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. ASTM D 5 D5, Standard Test Method of Test for Penetration of Bituminous Materials, 2006 2013. ASTM D 56 D56, Standard Test Method for Flash Point by Tag Closed Cup Tester, 2005, Reappoved 2010. ASTM D 93 D93, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester, 2013 e1. ASTM D 323 D323, Standard Method of Test for Vapor Pressure of Petroleum Products (Reid Method), 2008, Reapproved 2014. ASTM D 3278 D3278, Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus, 1996, Reapproved 2011. ASTM D 3828 D3828, Standard Test Methods for Flash Point of Liquids by Small Scale Closed Cup Tester, 2012. ASTM D 4359 D4359, Standard Test for Determining Whether a Material in a Liquid or a Solid, 2006 1990, Reapproved 2012. 2.3.3 UL Publications. Underwriters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062-2096. UL 87, Standard for Power-Operated Dispensing Devices for Petroleum Products, 2001, Revised 2008. ANSI/ UL 842, Standard for Valves for Flammable Fluids, 2007, Revised 2011 201 4. ANSI/ UL 2080, Standard for Fire Resistant Tanks for Flammable and Combustible Liquids, 2000. ANSI/ UL 2085, Standard for Protected Aboveground Tanks for Flammable and Combustible Liquids, 1997, Revised 2010. UL 2245, Standard for Below-Grade Vaults for Flammable Liquid Storage Tanks, 2006. ANSI/ UL 2586, Standard for Hose Nozzle Valves, 2011, Revised 2012 201 4. 2.3.4 Other Publications. Merriam-Webster s Collegiate Dictionary, 11th edition, Merriam-Webster, Inc., Springfield, MA, 2003. Referenced current SDO standard names, and years. Related Public Inputs for This Document Related Input Public Input No. 2-NFPA 30A-2015 [Global Input] Public Input No. 4-NFPA 30A-2015 [Section No. D.1.2] Relationship

of 105 1/21/2016 7:49 AM Submitter Full Name: Aaron Adamczyk Organization: [ Not Specified ] Submittal Date: Fri Feb 06 23:53:13 EST 2015 Resolution: FR-24-NFPA 30A-2015 Statement: Updated to current reference editions.

0 of 105 1/21/2016 7:49 AM Public Input No. 58-NFPA 30A-2015 [ Section No. 2.3.1 ] 2.3.1 API Publications. American Petroleum Institute, 1220 L Street, N.W., Washington, DC 20005-4070. API Std 607, Fire Test for Soft-Seated Quarter-Turn Valves, 5th edition, June 2005. and Valves Equipped with Non-Metallic Seats, 6th edition, 2010 API RP 1626, Storing and Handling of Ethanol and Gasoline-Ethanol Blends at Distribution Terminals and Filling Stations, 2nd Edition 2010 included Errata 1 (2011) and Addendum (2012) API RP 1646, Safe Work Practices for Petroleum/Convenience Facilities Downstream Segment. 1st Edition, 2006 updates and correct referenced standard. Adds two new referenced RPs proposed for addition in this code. Submitter Full Name: RICHARD KRAUS Organization: APIPETROLEUM SAFETY CONSULTAN Submittal Date: Thu Jul 02 15:20:30 EDT 2015 Resolution: The committee agreed that these references are more appropriately referenced in the annex. See FR 16.

1 of 105 1/21/2016 7:49 AM Public Input No. 80-NFPA 30A-2015 [ Section No. 2.3.3 ] 2.3.3 UL Publications. Underwriters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062-2096. ANSI/ UL 79, Standard for Power-Operated Pumps for Petroleum Dispensing Products, 2014 ANSI/UL 79A Standard for Power-Operated Pumps for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), 2015 UL 87, Standard for Power-Operated Dispensing Devices for Petroleum Products, 2001, Revised 2008. ANSI/UL 87A, Standard for Power-Operated Dispensing Devices for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0-E85), 2015 ANSI/UL 330, Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids, 2013 UL 330A Outline of Investigation for Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Gasoline and Gasoline/Ethanol Blends With Nominal Ethanol Concentrations Up To 85 Percent (E0 - E85), 2012 ANSI/UL 567, Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-Gas, 2014 ANSI/UL 567A Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85), 2015 ANSI/UL 842, Standard for Valves for Flammable Fluids, 2007, Revised 2011. ANSI/UL 842A Standard for Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85), 2015 ANSI/UL 2080, Standard for Fire Resistant Tanks for Flammable and Combustible Liquids, 2000. ANSI/UL 2085, Standard for Protected Aboveground Tanks for Flammable and Combustible Liquids, 1997, Revised 2010. UL 2245, Standard for Below-Grade Vaults for Flammable Liquid Storage Tanks, 2006. ANSI/UL 2586, Standard for Hose Nozzle Valves, 2011, Revised 2012. ANSI/UL 2586A Standard for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85), 2015 These standards have been added as reference standards in the body of the code, many of them were previously included in the annex. Corresponding code changes propose reference to these standards in the body of the code. This change will now allow them to be enforced rather than suggested to be followed. Submitter Full Name: HOWARD HOPPER Organization: UL LLC Submittal Date: Mon Jul 06 16:28:47 EDT 2015

2 of 105 1/21/2016 7:49 AM Resolution: The committee agreed that these references are more appropriately referenced in the annex. See FR 16.

3 of 105 1/21/2016 7:49 AM Public Input No. 42-NFPA 30A-2015 [ Section No. 2.4 ] 2.4 References for Extracts in Mandatory Sections. NFPA 2, Hydrogen Technologies Code, 2016 edition. NFPA 30, Flammable and Combustible Liquids Code, 2015 edition. Adds NFPA 2 2016 to the list in section 2.4. No other changes proposed despite what Terra may be showing. NFPA 2, Hydrogen Technologies Code, is not currently referenced in Section 2.4 References for Extracts in Mandatory Sections. Requirements for hydrogen refueling, hydrogen generation, hydrogen fuel cells, hydrogen-fueled vehicles in parking / repair garages, etc. are contained only in NFPA 2 and nowhere else. Previous text in NFPA 52 has been removed. The Standards Council has revised the Scope of NFPA 52 and removed fueling of hydrogen-fuel cell vehicles (FCV). NFPA 30A contains section that are mandatory per NFPA 2. NFPA 2 is a mandatory reference. Related Public Inputs for This Document Related Input Public Input No. 38-NFPA 30A-2015 [Section No. 7.4.2] Relationship The text proosed in 7.4.2 as well in other sections makes NFPA 2 a mandatory reference. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 18:07:24 EDT 2015 Resolution: CI-25-NFPA 30A-2015 Statement: Extracts from NFPA 2 have not yet been added to the code. This is being addressed by a task group and may be added at the second draft stage.

4 of 105 1/21/2016 7:49 AM Public Input No. 63-NFPA 30A-2015 [ Section No. 2.4 ] 2.4 References for Extracts in Mandatory Sections. NFPA 2, Hydrogen Technologies Code, 2016 edition. NFPA 30, Flammable and Combustible Liquids Code, 2015 edition. NFPA Standard Council has moved all hydrogen requirements from NFPA52 to NFPA2, including those for Motor Fueling Dispensing and Repair Garages. The 2011 version of the NFPA2 had specific information on Dispensing, but not for Repair Garages (reserved). The 2016 version of NFPA2 will have specific requirements for Repair Garages and will be published prior to NFPA30A. PI 22 makes a mandatory reference to NFPA2. Related Public Inputs for This Document Related Input Public Input No. 22-NFPA 30A-2015 [Section No. 7.4.2] Relationship PI 22 provides a mandatory reference to NFPA2 Submitter Full Name: SPENCER QUONG Organization: QUONG & ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 13:36:55 EDT 2015 Resolution: CI-25-NFPA 30A-2015 Statement: Extracts from NFPA 2 have not yet been added to the code. This is being addressed by a task group and may be added at the second draft stage.

5 of 105 1/21/2016 7:49 AM Public Input No. 57-NFPA 30A-2015 [ Section No. 4.2 ] 4.2 General Requirements. 4.2.1 Liquids shall be stored in the following: (1) Approved closed containers that do not exceed 227 L (60 gal) capacity and are located outside buildings (2) Tanks or approved closed containers located inside motor fuel dispensing facilities or repair garages (3) Aboveground tanks, underground tanks, and containers in accordance with the requirements of Section 4.3 (4) Tanks supplying marine service stations in accordance with Section 11.2 4.2.2 A motor fuel dispensing facility located at a bulk plant shall be separated from areas in which bulk plant operations are conducted by a fence or other approved barrier. Dispensing devices at the motor fuel dispensing facility shall not be supplied by aboveground tanks located in the bulk plant. Storage tanks at motor fuel dispensing facilities shall not be connected by piping to aboveground tanks located in the bulk plant. 4.2.3 Class I liquids shall not be stored or handled in a building that has a basement or pit into which ignitible vapors can travel, unless the basement or pit is provided with ventilation that will prevent the accumulation of vapors. The ventilation system shall be capable of providing at least 0.3 m 3 /min of exhaust per m 2 of floor area (1 cfm per ft 2 ), but not less than 4 m 3 /min (150 ft 3 /min). 4.2.4 Where tanks are at an elevation that produces a gravity head on the dispensing device, the tank outlet shall be equipped with a device, such as a normally closed solenoid valve, positioned adjacent to and downstream from the valve specified in 22.13.1 of NFPA 30, Flammable and Combustible Liquids Code, that is installed and adjusted so that liquid cannot flow by gravity from the tank if the piping or hose fails when the dispenser is not in use. 4.2.5 Storage of ethanol and gasoline ethanol blends shll be in coordance with the requirements of API RP 1626. adds new section providing for safe handling and storage of ethanol based fuels Submitter Full Name: RICHARD KRAUS Organization: APIPETROLEUM SAFETY CONSULTAN Submittal Date: Thu Jul 02 15:14:32 EDT 2015

6 of 105 1/21/2016 7:49 AM Resolution: FR-14-NFPA 30A-2015 Statement: The committee agrees that additional guidance found in API RP 1626 is of value to the user. Because the document is a recommended practice it must be referenced in the annex.

7 of 105 1/21/2016 7:49 AM Public Input No. 61-NFPA 30A-2015 [ New Section after 4.3.2.7 ] TITLE OF NEW CONTENT Type your content here... 4.3.2.8 Non-metallic tanks manufactured in compliance with and listed to UL SU 2258 shall be applicable in indoor and outdoor aboveground installation for Class II, Class IIIA and Class IIIB liquids. Installation, spacing and venting per the requirements of Section 4.3, Storage of Liquids This addition to NFPA 30A would allow tanks manufactured to UL SU 2259 to be applied in combustible liquids storage installations where specified in the scope of SU 2258 supported by extensive and rigorous testing requirements of the standard. From Subject 2258 Introduction: 1.1 These requirements cover nonmetallic or composite primary, secondary and diked type atmospheric tanks from 60-660 gallons (227-2500L) intended primarily for the storage and supply of heating fuel for oil burning equipment, or alternately the storage of diesel fuels for compression ignition engines and motor oils (new and used) for automotive service stations, in above ground installations. With the exception of standards UL 2080 (fire resistant tanks) and UL 2085 (protected tanks), UL SU 2258 would be the only other construction standard for combustible liquid storage with a pool fire test requirement. Submitter Full Name: BRUCE STOWE Organization: ROTH INDUSTRIES INCORPORATED Affilliation: N/A Submittal Date: Mon Jul 06 11:17:30 EDT 2015 Resolution: These tanks are not recognized or referenced in NFPA 30. NFPA 30A relies on tank specifications from NFPA 30.

8 of 105 1/21/2016 7:49 AM Public Input No. 35-NFPA 30A-2015 [ New Section after 4.3.6.6 ] 4.3.6.7 All devices and components of the tank and piping system must follow manufactures recommendations for installation, calibration, maintenance, etc. Not enforceable as written. Must have guideline requirements to ensure proper installation and maintenance. Submitter Full Name: MARCIA POXSON Organization: MICHIGAN BUREAU OF FIRE SERVIC Submittal Date: Tue Jun 30 14:24:46 EDT 2015 Resolution: CI-15-NFPA 30A-2015 Statement: The proposal has merit, but the committee is concerned that it only applies to some of the components within the scope of the code. A task group will make a recommendation on appropriate changes at the second draft stage.

9 of 105 1/21/2016 7:49 AM Public Input No. 36-NFPA 30A-2015 [ New Section after 5.7 ] 5.8 Underground Piping. Underground piping must be approved doublewall with approved monitoring. Aligns NFPA requirements with federal underground storage tank rules. Requiring monitoring of underground piping would prevent or limit environment exposure and hence, fire potential. Submitter Full Name: MARCIA POXSON Organization: MICHIGAN BUREAU OF FIRE SERVIC Submittal Date: Tue Jun 30 14:27:19 EDT 2015 Resolution: The current federal regulations governing the use of this type of piping are considered sufficient.

0 of 105 1/21/2016 7:49 AM Public Input No. 79-NFPA 30A-2015 [ New Section after 6.2.3 ] 6.2.4 Fuel dispensing systems and components intended for use with ethanol or gasoline/ethanol mixtures above E10 shall be listed in accordance with the following standards. (1) Dispensers: ANSI/UL 87A Standard for Power-Operated Dispensing Devices for Gasoline or Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0-E85). (2) Pumps: ANSI/UL 79 Standard for Power-Operated Pumps for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0 - E85). (3) Hose Assemblies: UL 330A Outline for Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Gasoline and Gasoline/Ethanol Blends With Nominal Ethanol Concentrations Up To 85 Percent (E0 - E85), (4) Hose Nozzles Valves: UL 2586A Standard for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0 - E85). (5) Swivel Connectors: UL 567A Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0 - E85. (6) Breakaways: UL 567A Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0 - E85). (7) Dispenser Emergency Shutoff Valves UL 842A Standard for Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85) Section 6.2.3 currently requires dispensing equipment intended for use with alcohol-blended motor fuels to be listed or approved for the specific purpose. This was a good requirement when systems and components were not listed for this use. However a new generation of UL standards was developed to evaluate and list the components covered by this section for such use. This proposal provides the code user with references to the standards used to evaluate fuels with ethanol concentrations above E10. Submitter Full Name: HOWARD HOPPER Organization: UL LLC Submittal Date: Mon Jul 06 16:10:28 EDT 2015 Resolution: FR-16-NFPA 30A-2015 Statement: These standards proposed in PI 79 are already addressed in the annex and the committee has updated the annex to reflect the updated standards.

1 of 105 1/21/2016 7:49 AM Public Input No. 78-NFPA 30A-2015 [ Section No. 6.2.3 ] 6.2.3 * Fuel dispensing systems, including dispensers, hoses, nozzles, breakaway fittings, swivels, flexible connectors, dispenser emergency shutoff valves, vapor recovery systems, and pumps that are used for alcohol-blended motor fuels shall be listed or approved for the specific purpose. and components shall be listed in accordance with the following standards, or the standards included in Section 6.2.4: (1) Dispensers: ANSI/UL 87A Standard for Power-Operated Dispensing Devices for Petroleum Products. (2) Pumps: ANSI/UL 79, Standard for Powered-Operated Pumps for Petroleum Dispensing Products. (3) Hose Assemblies: ANSI/UL 330, Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids. (4) Hose Nozzles Valves: ANSI/UL 2586, Standard for Hose Nozzle Valves. (5) Swivel Connectors: ANSI/UL 567, Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Petroleum Products. (6) Breakaways: ANSI/UL 567, Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Petroleum Products. (7) Dispenser Emergency Shutoff Valves ANSI/UL 842, Standard for Valves for Flammable Fluids. The body of the code stated that specific products were to be listed but there was no listed standard in the body of the code to support the requirement it was located in the Annex, which is unenforceable. This creates an enforcement nightmare because there was a disconnection between what the code demands and the means to attain it. This change resolves that issue. Submitter Full Name: HOWARD HOPPER Organization: UL LLC Submittal Date: Mon Jul 06 16:00:10 EDT 2015 Resolution: FR-16-NFPA 30A-2015 Statement: These standards proposed in PI 79 are already addressed in the annex and the committee has updated the annex to reflect the updated standards.

2 of 105 1/21/2016 7:49 AM Public Input No. 83-NFPA 30A-2015 [ Section No. 6.3.2 ] 6.3.2 Dispensing devices for Class I and Class II liquids shall be listed in accordance with ANSI/UL 87A Standard for Power-Operated Dispensing Devices for Gasoline or ANSI/UL 87A Standard for Power- Operated Dispensing Devices for Gasoline or Gasoline/Ethanol Blends with Nominal Ethanol Concentrations Up to 85 Percent (E0-E85). 6.3.2.1 Existing listed or labeled dispensing devices shall be permitted to be modified provided that the modifications made are Listed by Report by an approved testing laboratory or as otherwise approved by the authority having jurisdiction. Modification proposals shall contain a description of the component parts used in the modification and the recommended methods of installation on specific dispensing devices. Modification proposals shall be made available to the authority having jurisdiction upon request. This proposal clarifies the standards used to list dispensing devices. In a separate proposal UL 87A was added to Section 2.3.3. Submitter Full Name: HOWARD HOPPER Organization: UL LLC Submittal Date: Mon Jul 06 16:41:43 EDT 2015 Resolution: The committee agrees that these references are more appropriately referenced in the annex. See FR 16.

3 of 105 1/21/2016 7:49 AM Public Input No. 14-NFPA 30A-2015 [ Section No. 6.4.2 ] 6.4.2 Each pump shall have installed on the discharge side a listed leak detection device that will provide an audible or visible indication restricts or shuts off the flow of product. if the piping or a dispenser is leaking. Each leak-detecting device shall be checked and tested at least annually according to the manufacturer's specifications to ensure proper installation and operation. Exception: A leak detection device shall not be required if all piping is visible. Additional Proposed Changes File Name 30A-PC7.pdf Description Approved 30A PC7 NOTE: The following Public Input appeared as "Reject but Hold" in Public Comment No. 7 of the A2014 Second Draft Report for NFPA 30A and per the Regs. at 4.4.8.3.1 The wording in this section of the code makes it impossible to comply with. No leak detector installed on the discharge side of the pump provides an audible or visible alarm. Line leak detectors used on remote submersible pumps are not capable of sounding an audible or visible alarm, they use a pressure differential in the piping to either restrict the flow of product to the dispenser (mechanical line leak detectors) or shut off the flow of product (electronic line leak detectors). Submitter Full TC ON AUV-AAA Name: NFPA Technical Committee on Automotive and Marine Service Organization: Stations Submittal Date: Thu Mar 26 10:49:50 EDT 2015 Resolution: FR-28-NFPA 30A-2015 Statement: Line leak detectors used on remote submersible pumps are not capable of sounding an audible or visual alarm. They use a pressure differential in the piping to either restrict the flow of product to the dispenser or shut of the flow of product completely.

of 1 http://submittalsarchive.nfpa.org/terraviewweb/formlaunch?id=/terrav... 3/26/2015 9:45 AM Public Comment No. 7-NFPA 30A-2013 [ Section No. 6.4.2 ] 6.4.2 Each pump shall have installed on the discharge side a listed leak detection device that will provide an audible or visible indication restricts or shuts off the flow of product if the piping or a dispenser is leaking. Each leak-detecting device shall be checked and tested at least annually according to the manufacturer's specifications to ensure proper installation and operation. Exception : A leak detection device shall not be required if all piping is visible. Additional Proposed Changes File Name Description Approved 30A_Ralston_6.4.2.docx Cover Sheet Statement of Problem and Substantiation for Public Comment The wording in this section of the code makes it impossible to comply with. No leak detector installed on the discharge side of the pump provides an audible or visible alarm. Line leak detectors used on remote submersible pumps are not capable of sounding an audible or visible alarm, they use a pressure differential in the piping to either restrict the flow of product to the dispenser (mechanical line leak detectors) or shut off the flow of product (electronic line leak detectors). Submitter Full Name: ALEX RALSTON Organization: PETCON INC Submittal Date: Tue Apr 23 08:30:19 EDT 2013 Committee Action: Resolution: Rejected but held Public Comment No. 7 proposes a change to a paragraph in NFPA 30A that was not amended at the First Draft stage of this revision cycle. To accept this change would effect an amendment to the Code without its having undergone public review and comment. Therefore, in accordance with Paragraphs 4.4.4.2 and 4.4.8.3 of the Regulations Governing the Development of NFPA Standards, the Technical Committee has voted to reject Public Comment No. 7 and hold it for processing as a Public Input at the next document revision cycle. Copyright Assignment I, ALEX RALSTON, hereby irrevocably grant and assign to the National Fire Protection Association (NFPA) all and full rights in copyright in this Public Comment (including both the Proposed Change and the Statement of Problem and Substantiation). I understand and intend that I acquire no rights, including rights as a joint author, in any publication of the NFPA in which this Public Comment in this or another similar or derivative form is used. I hereby warrant that I am the author of this Public Comment and that I have full power and authority to enter into this copyright assignment. By checking this box I affirm that I am ALEX RALSTON, and I agree to be legally bound by the above Copyright Assignment and the terms and conditions contained therein. I understand and intend that, by checking this box, I am creating an electronic signature that will, upon my submission of this form, have the same legal force and effect as a handwritten signature

4 of 105 1/21/2016 7:49 AM Public Input No. 84-NFPA 30A-2015 [ Section No. 6.5.1 ] 6.5.1 Listed hose assemblies shall be used to dispense fuel. Hose Hose assemblies shall be be listed in accordance with ANSI/UL 330, Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids or UL 330A Outline for Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Gasoline and Gasoline/Ethanol Blends With Nominal Ethanol Concentrations Up To 85 Percent (E0 - E85). H ose length at automotive motor fuel dispensing facilities shall not exceed 5.5 m (18 ft). Where hose length at marine motor fuel dispensing facilities exceeds 5.5 m (18 ft), the hose shall be secured so as to protect it from damage. This identifies the standards used to investigate and list hose assemblies. Submitter Full Name: HOWARD HOPPER Organization: UL LLC Submittal Date: Mon Jul 06 16:47:54 EDT 2015 Resolution: The committee agreed that these references are more appropriately referenced in the annex. See FR 16.

5 of 105 1/21/2016 7:49 AM Public Input No. 15-NFPA 30A-2015 [ Sections 6.7.1, 6.7.2 ] Sections 6.7.1, 6.7.2 6.7.1 At attended motor fuel dispensing facilities, the devices or disconnects shall be readily accessible to the attendant and labeled with an approved sign stating "EMERGENCY FUEL SHUTOFF". 6.7.2 At unattended motor fuel dispensing facilities, the devices or disconnects shall be readily accessible to patrons and at least one additional device or disconnect shall be readily accessible to each group of dispensing devices on an individual island. The device(s) or disconnect(s) shall be labeled with an approved sign stating "EMERGENCY FUEL SHUTOFF". Additional Proposed Changes File Name Description Approved 30A-PC4.pdf NFPA 30A Public Comment 4. NOTE: The following Public Input appeared as "Reject but Hold" in Public Comment No. 4 of the A2014 Second Draft Report for NFPA 30A and per the Regs. at 4.4.8.3.1. Shut-offs should be labeled as to their operation so they can be easily identified by attendants and/or patrons that may be required to use them. Submitter Full TC ON AUV-AAA Name: NFPA Technical Committee on Automotive and Marine Service Organization: Stations Submittal Date: Thu Mar 26 11:01:26 EDT 2015 Resolution: FR-29-NFPA 30A-2015 Statement: The committee agrees that all emergency shutoff devices should be clearly identified.

of 1 http://submittalsarchive.nfpa.org/terraviewweb/formlaunch?id=/terrav... 3/26/2015 9:48 AM Public Comment No. 4-NFPA 30A-2013 [ Sections 6.7.1, 6.7.2 ] Sections 6.7.1, 6.7.2 6.7.1 At attended motor fuel dispensing facilities, the devices or disconnects shall be readily accessible to the attendant and labeled with an approved sign stating EMERGENCY FUEL SHUTOFF.. 6.7.2 At unattended motor fuel dispensing facilities, the devices or disconnects shall be readily accessible to patrons and at least one additional device or disconnect shall be readily accessible to each group of dispensing devices on an individual island. The device(s) or disconnect(s) shall be labeled with an approved sign stating EMERGENCY FUEL SHUTOFF. Statement of Problem and Substantiation for Public Comment Shut-offs should be labeled as to their operation so they can be easily identified by attendants and/or patrons that may be required to use them. Submitter Full Name: Doug Hohbein Organization: Northcentral Fire Code Develop Submittal Date: Tue Apr 02 22:00:55 EDT 2013 Committee Action: Resolution: Rejected but held Public Comment No. 4 proposes a change to a paragraph in NFPA 30A that was not amended at the First Draft stage of this revision cycle. To accept this change would effect an amendment to the Code without its having undergone public review and comment. Therefore, in accordance with Paragraphs 4.4.4.2 and 4.4.8.3 of the Regulations Governing the Development of NFPA Standards, the Technical Committee has voted to reject Public Comment No. 4 and hold it for processing as a Public Input at the next document revision cycle. Copyright Assignment I, Doug Hohbein, hereby irrevocably grant and assign to the National Fire Protection Association (NFPA) all and full rights in copyright in this Public Comment (including both the Proposed Change and the Statement of Problem and Substantiation). I understand and intend that I acquire no rights, including rights as a joint author, in any publication of the NFPA in which this Public Comment in this or another similar or derivative form is used. I hereby warrant that I am the author of this Public Comment and that I have full power and authority to enter into this copyright assignment. By checking this box I affirm that I am Doug Hohbein, and I agree to be legally bound by the above Copyright Assignment and the terms and conditions contained therein. I understand and intend that, by checking this box, I am creating an electronic signature that will, upon my submission of this form, have the same legal force and effect as a handwritten signature

6 of 105 1/21/2016 7:49 AM Public Input No. 59-NFPA 30A-2015 [ New Section after 7.2 ] TITLE OF NEW CONTENT Type your content here 7.2.1 Safe Construction Practices Contractors working at service station facilities shall comply with the requirements of API RP 1646, Safe Work Practices for Contractors Working at Retail Petroleum/Convenience Facilities.... Provides safety requirements for contractors working in service stations Submitter Full Name: RICHARD KRAUS Organization: APIPETROLEUM SAFETY CONSULTAN Submittal Date: Thu Jul 02 15:37:10 EDT 2015 Resolution: Since a copy of the document was not submitted with the proposal, the committee was unable to review it and to assess its applicability. Based on its title, it does not appear that the document is within the scope of NFPA 30A.

7 of 105 1/21/2016 7:49 AM Public Input No. 45-NFPA 30A-2015 [ Section No. 7.3.1 ] 7.3.1 Occupancy Classification. The occupancy classification of a motor fuel dispensing facility that is located inside a building or structure shall be a special purpose industrial occupancy as defined in NFPA 101, Life Safety Code determined in accordance with the building code adopted for the jurisdiction. Occupancy classifications are assigned by the Building code adopted in a jurisdiction. Special purpose industrial occupancy is an incorrect classification (see below) and this is a complicated situation best handled by requirements already clearly established in the building code. For most occupancies, adding a motor fuel dispensing facility inside an existing building would cause the MAQ to be exceeded if the storage is also inside, which would cause the occupancy to be a high hazard Group H occupancy and/or invoke additional Protection Level requirement (analogous to Group H) if NFPA 1 were to be enforced. Regardless, a special purpose industrial occupancy has lower egress requirements (not higher) that a standard industrial occupancy so this is not an appropriate occupancy classification. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Fuel dispensing facilities do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 46-NFPA 30A-2015 [Section No. 7.3.1] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 18:35:03 EDT 2015 Resolution: FR-6-NFPA 30A-2015 Statement: The committee determined that it is necessary to retain the classification of special purpose industrial occupancy, particularly as it pertains for indoor fueling. In the areas where NFPA 101 is not adopted, the local building code would be in effect.

8 of 105 1/21/2016 7:49 AM Public Input No. 46-NFPA 30A-2015 [ Section No. 7.3.1 ] 7.3.1 Occupancy Classification. The occupancy classification of a motor fuel dispensing facility that is located inside a building or structure shall be a special purpose an industrial occupancy as defined in NFPA 101, Life Safety Code. The change proposed in PI No 45 is preferred over this one but if PI No 45 is rejected (resolved) then this one is my 2nd choice. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Fuel dispensing facilities do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 45-NFPA 30A-2015 [Section No. 7.3.1] Relationship If PI 45 is accepted then this one should be rejected. And vice-versa. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 18:53:49 EDT 2015 Resolution: FR-6-NFPA 30A-2015 Statement: The committee determined that it is necessary to retain the classification of special purpose industrial occupancy, particularly as it pertains for indoor fueling. In the areas where NFPA 101 is not adopted, the local building code would be in effect.

9 of 105 1/21/2016 7:49 AM Public Input No. 64-NFPA 30A-2015 [ Section No. 7.3.1 ] 7.3.1 Occupancy Classification. The occupancy classification of a motor fuel dispensing facility that is located inside a building or structure shall be a special purpose industrial occupancy as defined in NFPA 101, Life Safety Code be in accordance with the building code adopted for the jurisdiction. Occupancy classifications are assigned by the Building code adopted in a jurisdiction. Special purpose industrial occupancy is an incorrect classification (see below) and this is a complicated situation best handled by requirements already clearly established in the building code. For most occupancies, adding a motor fuel dispensing facility inside an existing building would cause the MAQ to be exceeded if the storage is also inside, which would cause the occupancy to be a high hazard Group H occupancy and/or invoke additional Protection Level requirement (analogous to Group H) if NFPA 1 were to be enforced. Regardless, a special purpose industrial occupancy has lower egress requirements (not higher) that a standard industrial occupancy so this is not an appropriate occupancy classification. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Fuel dispensing facilities do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 65-NFPA 30A-2015 [Section No. 7.3.1] Relationship Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 13:50:05 EDT 2015 Resolution: FR-6-NFPA 30A-2015 Statement: The committee determined that it is necessary to retain the classification of special purpose industrial occupancy, particularly as it pertains for indoor fueling. In the areas where NFPA 101 is not adopted, the local building code would be in effect.

0 of 105 1/21/2016 7:49 AM Public Input No. 65-NFPA 30A-2015 [ Section No. 7.3.1 ] 7.3.1 Occupancy Classification. The occupancy classification of a motor fuel dispensing facility that is located inside a building or structure shall be a special purpose an industrial occupancy as defined in NFPA 101, Life Safety Code. PI 65 should only be considered if PI 64 is rejected. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Fuel dispensing facilities do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 64-NFPA 30A-2015 [Section No. 7.3.1] Relationship Optional proposal if PI64 rejected Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 13:53:24 EDT 2015 Resolution: FR-6-NFPA 30A-2015 Statement: The committee determined that it is necessary to retain the classification of special purpose industrial occupancy, particularly as it pertains for indoor fueling. In the areas where NFPA 101 is not adopted, the local building code would be in effect.

1 of 105 1/21/2016 7:49 AM Public Input No. 47-NFPA 30A-2015 [ Section No. 7.3.3 ] 7.3.3 Means of Egress. In a motor fuel dispensing facility that is located inside a building or structure, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. Occupancy classifications are assigned by the Building code adopted in a jurisdiction. The building code adopted by the jurisdiction will address egress. This section is not needed. If a jurisdiction uses NFPA 101 for egress, then the conflict between the IBC and NFPA 101 will be addressed in their adopting ordinances (typically by adopting NFPA 101 instead of IBC Ch 10. Either way, this section is not needed and creates conflict as is. Related Public Inputs for This Document Related Input Public Input No. 48-NFPA 30A-2015 [Section No. 7.3.3] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 19:02:38 EDT 2015 Resolution: FR-7-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

2 of 105 1/21/2016 7:49 AM Public Input No. 48-NFPA 30A-2015 [ Section No. 7.3.3 ] 7.3.3 Means of Egress. In a motor fuel dispensing facility that is located inside a building or structure, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. Only needed if PI47 is rejected. If PI47 is approve then reject this one. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Fuel dispensing facilities do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 47-NFPA 30A-2015 [Section No. 7.3.3] Relationship If PI 47 is approved then this one is not needed and should be rejected. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 19:15:47 EDT 2015 Resolution: FR-7-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

3 of 105 1/21/2016 7:49 AM Public Input No. 66-NFPA 30A-2015 [ Section No. 7.3.3 ] 7.3.3 Means of Egress. In a motor fuel dispensing facility that is located inside a building or structure, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. This section is not needed because occupancy classifications and "means of egress" are assigned by the Building code adopted in a jurisdiction.if a jurisdiction uses NFPA 101 for egress, then the conflict between the IBC and NFPA 101 will be addressed in their adopting ordinances (typically by adopting NFPA 101 instead of IBC Ch 10. Either way, this section is not needed and creates conflict as is. Related Public Inputs for This Document Related Input Public Input No. 67-NFPA 30A-2015 [Section No. 7.3.3] Relationship Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 13:57:59 EDT 2015 Resolution: FR-7-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

4 of 105 1/21/2016 7:49 AM Public Input No. 67-NFPA 30A-2015 [ Section No. 7.3.3 ] 7.3.3 Means of Egress. In a motor fuel dispensing facility that is located inside a building or structure, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. This PI should only be considered if PI66 is rejected. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Fuel dispensing facilities do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 66-NFPA 30A-2015 [Section No. 7.3.3] Relationship PI 67 is an optional proposal only to be considered if PI 66 is rejected Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:00:02 EDT 2015 Resolution: FR-7-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

5 of 105 1/21/2016 7:49 AM Public Input No. 70-NFPA 30A-2015 [ Section No. 7.4.1 ] 7.4.1 Occupancy Classification. The occupancy classification of a repair garage shall be a special purpose industrial occupancy as defined in NFPA 101, Life Safety Code. in accordance with the building code adopted for the jurisdiction PI Occupancy classifications are assigned by the Building code adopted in a jurisdiction. Special purpose industrial occupancy is an incorrect classification (see below) and this is a complicated situation best handled by requirements already clearly established in the building code. A special purpose industrial occupancy has lower egress requirements (not higher) that a standard industrial occupancy so this is not an appropriate occupancy classification. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 77-NFPA 30A-2015 [Section No. 7.4.1] Relationship Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:16:40 EDT 2015 Resolution: FR-8-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

6 of 105 1/21/2016 7:49 AM Public Input No. 77-NFPA 30A-2015 [ Section No. 7.4.1 ] 7.4.1 Occupancy Classification. The occupancy classification of a repair garage shall be a special purpose an industrial occupancy as defined in NFPA 101, Life Safety Code. If the technical committee rejects my preferred option to remove the reference to NFPA101 as proposed in PI 70, then, I propose removing the "special purpose" from industrial occupancies. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to repair garages: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 70-NFPA 30A-2015 [Section No. 7.4.1] Relationship Secondary proposal if PI70 is rejected Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 15:01:09 EDT 2015 Resolution: FR-8-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

7 of 105 1/21/2016 7:49 AM Public Input No. 81-NFPA 30A-2015 [ Section No. 7.4.1 ] 7.4.1 Occupancy Classification. The occupancy classification of a repair garage shall be a special purpose industrial occupancy as defined in NFPA 101, Life Safety Code in accordance with the building code adopted for the jurisdiction. Occupancy classifications are assigned by the Building code adopted in a jurisdiction. Special purpose industrial occupancy is an incorrect classification (see below) and this is a complicated situation best handled by requirements already clearly established in the building code. A special purpose industrial occupancy has lower egress requirements (not higher) that a standard industrial occupancy so this is not an appropriate occupancy classification. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 82-NFPA 30A-2015 [Section No. 7.4.1] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Mon Jul 06 16:29:34 EDT 2015 Resolution: FR-8-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

8 of 105 1/21/2016 7:49 AM Public Input No. 82-NFPA 30A-2015 [ Section No. 7.4.1 ] 7.4.1 Occupancy Classification. The occupancy classification of a repair garage shall be a special purpose an industrial occupancy as defined in NFPA 101, Life Safety Code. If the technical committee rejects my preferred option to remove the reference to NFPA101 as proposed in PI 81, then, I propose removing the "special purpose" from industrial occupancies. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to repair garages: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 81-NFPA 30A-2015 [Section No. 7.4.1] Relationship preferred option is in PI 81. This is a secondary input Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Mon Jul 06 16:33:56 EDT 2015 Resolution: FR-8-NFPA 30A-2015 Statement: This revision was made to correspond with FR 6.

9 of 105 1/21/2016 7:49 AM Public Input No. 22-NFPA 30A-2015 [ Section No. 7.4.2 ] 7.4.2 General Construction Requirements. In major repair garages, where CNG-fueled vehicles, hydrogen-fueled vehicles, LNG-fueled vehicles, or LP-Gas-fueled vehicles are repaired, all applicable requirements of NFPA 52, Vehicular Gaseous Fuel Systems Code, NFPA2, Hydrogen Technologies Code, or NFPA 58, Liquefied Petroleum Gas Code, whichever is applicable, shall be met. NFPA Standard Council has moved all hydrogen requirements from NFPA52 to NFPA2, including those for Motor Fueling Dispensing and Repair Garages. The 2011 version of the NFPA2 code had specific information on Dispensing, but not for Repair Garages (reserved). The 2016 version of NFPA2 will have specific requirements for Repair Garages and will be published prior to NFPA30A. Therefore, in order to prevent conflicting requirements, repair garages should reference NFPA2 and not NFPA52. Related Public Inputs for This Document Related Input Public Input No. 63-NFPA 30A-2015 [Section No. 2.4] Relationship Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: Toyota Submittal Date: Fri May 15 03:05:23 EDT 2015 Resolution: FR-10-NFPA 30A-2015 Statement: Since hydrogen is now a viable alternative fuel, it should be specifically recognized in NFPA 30A.

0 of 105 1/21/2016 7:49 AM Public Input No. 38-NFPA 30A-2015 [ Section No. 7.4.2 ] 7.4.2 General Construction Requirements. In major repair garages, where CNG-fueled vehicles, hydrogen-fueled vehicles, LNG-fueled vehicles, or LP-Gas-fueled vehicles are repaired, all applicable requirements of NFPA 52, Vehicular Gaseous Fuel Systems Code, NFPA 2, Hydrogen Technologies Code, or NFPA 58, Liquefied Petroleum Gas Code, whichever is applicable, shall be met. Requirements for repair garages servicing hydrogen-fueled vehicles are contained only in NFPA 2 and nowhere else. Previous text in NFPA 52 has been removed. The Standards Council has revised the Scope of NFPA 52 and removed fueling of hydrogen-fuel cell electric vehicles. Related Public Inputs for This Document Related Input Public Input No. 42-NFPA 30A-2015 [Section No. 2.4] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 17:23:05 EDT 2015 Resolution: FR-10-NFPA 30A-2015 Statement: Since hydrogen is now a viable alternative fuel, it should be specifically recognized in NFPA 30A.

1 of 105 1/21/2016 7:49 AM Public Input No. 49-NFPA 30A-2015 [ Section No. 7.4.3 ] 7.4.3 Means of Egress. In a repair garage, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. Preferred option. Occupancy classifications are assigned by the Building code adopted in a jurisdiction. The building code adopted by the jurisdiction will address egress. This section is not needed. If a jurisdiction uses NFPA 101 for egress, then the conflict between the IBC and NFPA 101 will be addressed in their adopting ordinances (typically by adopting NFPA 101 instead of IBC Ch 10. Either way, this section is not needed and creates conflict as is. Related Public Inputs for This Document Related Input Public Input No. 50-NFPA 30A-2015 [Section No. 7.4.3] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 19:19:49 EDT 2015 Resolution: FR-11-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

2 of 105 1/21/2016 7:49 AM Public Input No. 50-NFPA 30A-2015 [ Section No. 7.4.3 ] 7.4.3 Means of Egress. In a repair garage, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. Only needed if PI49 is rejected. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages are rather common and do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 49-NFPA 30A-2015 [Section No. 7.4.3] Relationship If PI49 is accepted then this one PI50 should be rejected - or vice versa. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 19:22:47 EDT 2015 Resolution: FR-11-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

3 of 105 1/21/2016 7:49 AM Public Input No. 68-NFPA 30A-2015 [ Section No. 7.4.3 ] 7.4.3 Means of Egress. In a repair garage, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. This section is not needed because occupancy classifications and "means of egress" are assigned by the building code adopted in a jurisdiction.if a jurisdiction uses NFPA 101 for egress, then the conflict between the IBC and NFPA 101 will be addressed in their adopting ordinances (typically by adopting NFPA 101 instead of IBC Ch 10. Either way, this section is not needed and creates conflict as is. Related Public Inputs for This Document Related Input Public Input No. 69-NFPA 30A-2015 [Section No. 7.4.3] Relationship Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:05:49 EDT 2015 Resolution: FR-11-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

4 of 105 1/21/2016 7:49 AM Public Input No. 69-NFPA 30A-2015 [ Section No. 7.4.3 ] 7.4.3 Means of Egress. In a repair garage, the required number, location, and construction of means of egress shall meet all applicable requirements for special purpose industrial occupancies, as set forth in NFPA 101, Life Safety Code. This PI should only be considered if PI68 is rejected. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to repair garages: 3.3.190.8.3 Special- Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment Related Public Inputs for This Document Related Input Public Input No. 68-NFPA 30A-2015 [Section No. 7.4.3] Relationship PI69 should only be considered if PI68 is rejected Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:12:14 EDT 2015 Resolution: FR-11-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

5 of 105 1/21/2016 7:49 AM Public Input No. 56-NFPA 30A-2015 [ Section No. 7.4.4 ] 7.4.4 Drainage. In areas of repair garages used for repair or servicing of vehicles, floor assemblies shall be constructed of noncombustible materials or, if combustible materials are used in the assembly, they shall be surfaced with approved, nonabsorbent, noncombustible material. Exception: Slip-resistant, nonabsorbent, interior floor finishes having a critical radiant flux not more than 0.45 W/cm 2 (9.87 Btu/in. 2 ), as determined by NFPA 253, Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source, shall be permitted, except as permitted by 7.4.4.3. 7.4.4.1 Floors shall be liquidtight to prevent the leakage or seepage of liquids and shall be sloped to facilitate the movement of water, fuel, or other liquids to floor drains. 7.4.4.2 In areas of repair garages where vehicles are serviced, any floor drains shall be properly trapped and shall discharge through an oil/water separator to the sewer or to an outside vented sump. 7.4.4.3 Slip-resistant, nonabsorbent, interior floor finishes having a critical radiant flux not more than 0.45 W/cm2 (9.87 Btu/in. 2 ), as determined by NFPA 253, Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source or by ASTM E648,Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source, shall be permitted. (Also ad ASTM E648 2014c into the list of referenced ASTM standards in Chpater 2). This public input does two things: (a) adds reference to ASTM E648, which is completely equivalent to NFPA 253 and is used more often and is referenced in most NFPA codes as an acceptable alternative to NFPA 253 and (b) makes the exception into full text language, thus eliminating exceptions wherever possible, as recommended by Standards Council and the Manual of Style. Submitter Full Name: MARCELO HIRSCHLER Organization: GBH INTERNATIONAL Submittal Date: Thu Jul 02 13:00:33 EDT 2015 Resolution: The committee agrees that they are in accordance with the manual of style: "2.3.5 Exceptions. 2.3.5.1 Exceptions shall be permitted only where the exception represents an allowance or required alternate procedure to a general rule when limited, specified conditions apply." The committee also requests that the submitter provide a thorough comparison of the two standards (ASTM E648 and NFPA 253) for committee review.

6 of 105 1/21/2016 7:49 AM Public Input No. 51-NFPA 30A-2015 [ Section No. 7.4.5.3 ] 7.4.5.3 In pits, belowgrade work areas, and subfloor work areas, the required number, location, and construction of means of egress shall meet the requirements for special purpose industrial occupancies in Chapter 40 of NFPA 101, Life Safety Code. Preferred option. Occupancy classifications are assigned by the Building code adopted in a jurisdiction. The building code adopted by the jurisdiction will address egress. This section is not needed. If a jurisdiction uses NFPA 101 for egress, then the conflict between the IBC and NFPA 101 will be addressed in their adopting ordinances (typically by adopting NFPA 101 instead of IBC Ch 10. Either way, this section is not needed and creates conflict as is. Related Public Inputs for This Document Related Input Public Input No. 52-NFPA 30A-2015 [Section No. 7.4.5.3] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 19:29:02 EDT 2015 Resolution: FR-12-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

7 of 105 1/21/2016 7:49 AM Public Input No. 52-NFPA 30A-2015 [ Section No. 7.4.5.3 ] 7.4.5.3 In pits, belowgrade work areas, and subfloor work areas, the required number, location, and construction of means of egress shall meet the requirements for special purpose industrial occupancies in Chapter 40 of NFPA 101, Life Safety Code. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages are rather common and do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to fuel dispensing facilities: 3.3.190.8.3 Special-Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 51-NFPA 30A-2015 [Section No. 7.4.5.3] Relationship If PI 51 is accepted then PI 52 should be rejected and vice versa. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 19:30:52 EDT 2015 Resolution: FR-12-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

8 of 105 1/21/2016 7:49 AM Public Input No. 71-NFPA 30A-2015 [ Section No. 7.4.5.3 ] 7.4.5.3 In pits, belowgrade work areas, and subfloor work areas, the required number, location, and construction of means of egress shall meet the requirements for special purpose industrial occupancies in Chapter 40 of NFPA 101, Life Safety Code. This section is not needed because occupancy classifications and "means of egress" are assigned by the Building code adopted in a jurisdiction.if a jurisdiction uses NFPA 101 for egress, then the conflict between the IBC and NFPA 101 will be addressed in their adopting ordinances (typically by adopting NFPA 101 instead of IBC Ch 10. Either way, this section is not needed and creates conflict as is. Related Public Inputs for This Document Related Input Public Input No. 72-NFPA 30A-2015 [Section No. 7.4.5.3] Relationship Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:18:03 EDT 2015 Resolution: FR-12-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

9 of 105 1/21/2016 7:49 AM Public Input No. 72-NFPA 30A-2015 [ Section No. 7.4.5.3 ] 7.4.5.3 In pits, belowgrade work areas, and subfloor work areas, the required number, location, and construction of means of egress shall meet the requirements for special purpose for industrial occupancies in Chapter 40 of NFPA 101, Life Safety Code. This PI should only be considered if PI71 is rejected. Special-purpose industrial occupancies are intended for occupancies with uniquely low occupant load factors; not for occupancies that perform unique operations. Repair garages do not experience uniquely low occupant loads. In addition, egress may be inadequate if classified as a special purpose industrial occupancy. Refer to definition in NFPA 101 below as evidence that this classification is not applicable to repair garages: 3.3.190.8.3 Special- Purpose Industrial Occupancy. An industrial occupancy in which ordinary and low hazard industrial operations are conducted in buildings designed for, and suitable only for, particular types of operations, characterized by a relatively low density of employee population, with much of the area occupied by machinery or equipment. Related Public Inputs for This Document Related Input Public Input No. 71-NFPA 30A-2015 [Section No. 7.4.5.3] Relationship PI 72 should only be considered if PI71 is rejected Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:20:22 EDT 2015 Resolution: FR-12-NFPA 30A-2015 Statement: This revision was made to coordinate with FR 6.

Public Input No. 16-NFPA 30A-2015 [ Section No. 7.4.6 ] 7.4.6 Fixed Fire Protection. Automatic sprinkler protection installed in accordance with the requirements of NFPA 13, Standard for the Installation of Sprinkler Systems, shall be provided in major repair garages, as herein defined, when any of the following conditions exist: (1) The builidng housing the major repair garage is two or more stories in height levels, including basements, and any one of the floors exceeds 930 (2) The aggregate area of all levels combined exceeds 1115 m 2 ( 10 (3) 12,000 ft 2 ). (4) The major repair garage is one story (5) level and exceeds (6) exceed 1115 m 2 (12,000 ft 2 ). (7) The major repair garage is servicing vehicles parked in the basement of the building. Additional Proposed Changes File Name Description Approved 30A-PC1.pdf 30A PC #1. NOTE: The following Public Input appeared as "Reject but Hold" in Public Comment No. 1 of the A2014 Second Draft Report for NFPA 30A and per the Regs. at 4.4.8.3.1. Subsection 1 should clarify that the requirement applies to the entire building; the entire building does not have to be used as a repair garage to utilize this requirement. The current language of section 1 would allow a large area without sprinkler protection. (Example: 3 story building, 9,000 ft² per floor would not require sprinkler protection) Submitter Full Name: TC ON AUV-AAA NFPA NFPA Technical Committee on Automotive and Marine Organization: Service Stations Submittal Date: Thu Mar 26 11:16:00 EDT 2015 Resolution: FR-30-NFPA 30A-2015 0 of 105 1/21/2016 7:49 AM

of 2 http://submittalsarchive.nfpa.org/terraviewweb/formlaunch?id=/terrav... 3/26/2015 9:51 AM Public Comment No. 1-NFPA 30A-2013 [ Section No. 7.4.6 ] 7.4.6 Fixed Fire Protection. Automatic sprinkler protection installed in accordance with the requirements of NFPA 13, Standard for the Installation of Sprinkler Systems, shall be provided in major repair garages, as herein defined, when any of the following conditions exist: (1) The building housing the major repair garage is two or more stories in height (1) levels, including basements, and any one of the floors exceeds 930 m 2 (10,000 ft 2 ) (1) the aggregate area of all levels combined exceeds 12000 ft2. (2) The major repair garage is one story (1) level and exceeds 1115 m 2 (12,000 ft 2 ). (2) The major repair garage is servicing vehicles parked in the basement of the building. Statement of Problem and Substantiation for Public Comment Subsection 1 should clarify that the requirement applies to the entire building; the entire building does not have to be used as a repair garage to utilize this requirement. The current language of section 1 would allow a large area without sprinkler protection. (Example: 3 story building, 9,000 ft² per floor would not require sprinkler protection) Submitter Full Name: Doug Hohbein Organization: Northcentral Fire Code Develop Submittal Date: Tue Apr 02 21:54:45 EDT 2013 Committee Action: Resolution: Rejected but held Public Comment No. 1 proposes a change to a paragraph in NFPA 30A that was not amended at the First Draft stage of this revision cycle. To accept this change would effect an amendment to the Code without its having undergone public review and comment. Therefore, in accordance with Paragraphs 4.4.4.2 and 4.4.8.3 of the Regulations Governing the Development of NFPA Standards, the Technical Committee has voted to reject Public Comment No. 1 and hold it for processing as a Public Input at the next document revision cycle. Copyright Assignment I, Doug Hohbein, hereby irrevocably grant and assign to the National Fire Protection Association (NFPA) all and full rights in copyright in this Public Comment (including both the Proposed Change and the Statement of Problem and Substantiation). I understand and intend that I acquire no rights, including rights as a joint author, in any publication of the NFPA in which this Public Comment in this or another similar or derivative form is used. I hereby warrant that I am the author of this Public Comment and that I have full power and authority to enter into this copyright assignment. By checking this box I affirm that I am Doug Hohbein, and I agree to be legally bound by the above Copyright Assignment and the terms and conditions contained therein. I understand and intend that, by checking this box, I am creating an electronic signature that will, upon my submission of this form, have the same legal force and effect as a handwritten signature

of 2 http://submittalsarchive.nfpa.org/terraviewweb/formlaunch?id=/terrav... 3/26/2015 9:51 AM

1 of 105 1/21/2016 7:49 AM Statement: This clarifies that the requirement applies to the entire building.

2 of 105 1/21/2016 7:49 AM Public Input No. 73-NFPA 30A-2015 [ Section No. 7.4.7 ] 7.4.7 Gas Detection System. Repair garages used for repair of vehicle engine fuel systems fueled by non-odorized gases, with the exception of hydrogen, such as hydrogen and non-odorized LNG/CNG, shall be provided with an approved flammable gas detection system. 7.4.7.1 For repair garages used for the repair of hydrogen-fueled vehicles, the gas detection system shall be in accordance with NFPA 2, Hydrogen Technologies Code 7.4.7.2 System Design. The flammable gas detection system shall be calibrated to the types of fuels or gases used by vehicles to be repaired. The gas detection system shall be designed to activate when the level of flammable gas exceeds 25 percent of the lower flammable limit (LFL). Gas detection shall also be provided in lubrication or chassis repair pits of repair garages used for repairing non-odorized LNG/CNG-fueled vehicles. 7.4.7.2 3 Operation. Activation of the gas detection system shall result in all of the following: (1) Initiation of distinct audible and visual alarm signals in the repair garage (2) Deactivation of all heating systems located in the repair garage (3) Activation of the mechanical ventilation system, when the system is interlocked with gas detection 7.4.7.3 4 Failure of the Gas Detection System. Failure of the gas detection system shall result in the deactivation of the heating system and activation of the mechanical ventilation system and, where the ventilation system is interlocked with gas detection, shall cause a trouble signal to sound in an approved location. 7.4.7.4 5 The circuits of the detection system required by 7.4.7 shall be monitored for integrity in accordance with NFPA 72, National Fire Alarm and Signaling Code. NFPA Standard Council has moved all hydrogen requirements from NFPA52 to NFPA2, including those for Motor Fueling Dispensing and Repair Garages. The 2011 version of the NFPA2 code had specific information on Dispensing, but not for Repair Garages (reserved). The 2016 version of NFPA2 will have specific requirements for Repair Garages and Gas Detection Systems. NFPA2 will be published prior to NFPA30A. In order to prevent conflicting requirements, the gas detection system requirements for hydrogen should reference NFPA2 Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA Submittal Date: Mon Jul 06 14:25:31 EDT 2015

3 of 105 1/21/2016 7:49 AM Resolution: CI-13-NFPA 30A-2015 Statement: There are several other parameters that the committee would like to investigate, including potential extract of specific provisions from other related NFPA codes and standards. A task group will be assigned to work on the language for this section.

4 of 105 1/21/2016 7:49 AM Public Input No. 43-NFPA 30A-2015 [ Section No. 7.4.7 [Excluding any Sub-Sections] ] Repair garages used for repair of vehicle engine fuel systems fueled by non-odorized gases with the exception of hydrogen, such as hydrogen and non-odorized LNG/CNG, shall be provided with an approved flammable gas detection system. Special requirements for gas detection systems, including when these systems are required and how to install them, have already been developed in NFPA 2 for repair garages servicing hydrogen-fueled vehicles. A new pointer to NFPA 2 is proposed in new section 7.4.7.1. Related Public Inputs for This Document Related Input Public Input No. 44-NFPA 30A-2015 [New Section after 7.4.7.1] Relationship Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 18:20:32 EDT 2015 Resolution: CI-13-NFPA 30A-2015 Statement: There are several other parameters that the committee would like to investigate, including potential extract of specific provisions from other related NFPA codes and standards. A task group will be assigned to work on the language for this section.

5 of 105 1/21/2016 7:49 AM Public Input No. 44-NFPA 30A-2015 [ New Section after 7.4.7.1 ] New Section 7.4.7.1 - Renumber subsequent sections 7.4.7.1 For repair garages used for the repair of hydrogen-fueled vehicles, the gas detection system shall be in accordance with NFPA 2, Hydrogen Technologies Code. Special requirements for gas detection systems, including when these systems are required and how to install them, have already been developed in NFPA 2. This new section points the user to those requirements. Related Public Inputs for This Document Related Input Public Input No. 43-NFPA 30A-2015 [Section No. 7.4.7 [Excluding any Sub-Sections]] Relationship adds pointer and makes NFPA 30A complete with the exclusion of hydrogen proposed in PI43. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC Submittal Date: Wed Jul 01 18:23:52 EDT 2015 Resolution: CI-13-NFPA 30A-2015 Statement: There are several other parameters that the committee would like to investigate, including potential extract of specific provisions from other related NFPA codes and standards. A task group will be assigned to work on the language for this section.

6 of 105 1/21/2016 7:49 AM Public Input No. 25-NFPA 30A-2015 [ Section No. 8.2.1 ] 8.2.1 * In major repair garages where CNG vehicles are repaired or stored, the area within 455 mm (18 in.) of the ceiling shall be designated a Class I, Division 2 hazardous (classified) location. Exception: In major repair garages, where ventilation equal to not less than four air changes per hour is provided, this requirement shall not apply. The existing requirement as stated in 8.2.1 was based on the assumption as noted in Annex A8.2.1 that the creditable release on natural gas from the vehicle would be 150% of the largest on board storage cylinder. The volume released assumption was based on the noted premature failures of thermally activated PRDs (TPRD) experienced in the 1990's. Those TPRDS have gone through at least three generations on new designs and there has not been a documented failure (premature release) from TPRDs since 2002. This stems for the phase out of the older designs for the 1990's and the excellent performance record of the new TPRD designs. With thirteen years of no recorded failures (premature releases) of TPRDs mounted on hundreds of thousands of cylinders indicates that the release hazard covered by 8.2.1 no longer exists. A recent research paper (SAND2014-2342) from SANDIA National Laboratory and funded by the Clean Vehicle Education Foundation has determined that the expected creditable release for both CNG and LNG vehicles is of a much lower volume and dose not pose a hazard for a maintenance facility. The report includes gas dispersion modeling of the creditable releases showing the extent of the ignitable mixture. This modeling of the creditable mixtures indicate that the ignitable concentration is only within a narrow area no more than six feet from the point of release, also the limited volume of release does not allow for an increasing concentration in the ceiling area due to the dispersion of the gas.the full release as as noted in the 1990 assumption was also modeled for background information. The report also indicates that ventilation rates has little or no impact on the volume of ignitable mixture and the dispersion of the released gas.the report will be sent by separate cover as part of this proposal and an electronic copy is available to the TC as needed. The Annex A8.2.1 will need to be deleted and the TC should consider new annex material explaining the realities of creditable releases expected for contemporary facility designs, this information may be considered as Annex material for section 7.6.6 concerning locations of ignitable mixtures. NOTE: SANDIA has proposed a Phase 2 project to refine the assumptions for facility designs and CFD modeling starting in 2016 and would consider input from the NFPA 52 TC together define and understand the potential hazards. Submitter Full Name: DOUGLAS HORNE Organization: DBHORNE LLC Submittal Date: Fri May 22 09:41:49 EDT 2015 Resolution: CI-9-NFPA 30A-2015 Statement: Not all of the supporting documentation was available to the committee for review. This information will be reviewed and considered by the committee at the second draft stage. The committee also seeks information pertaining to the size of the garage and under conditions of no ventilation.

7 of 105 1/21/2016 7:49 AM Public Input No. 27-NFPA 30A-2015 [ Section No. 8.3.2 ]

8 of 105 1/21/2016 7:49 AM 8.3.2 *

9 of 105 1/21/2016 7:49 AM Table 8.3.2 shall be used to delineate and classify areas for the purposes of installing electrical wiring and electrical utilization equipment where Class I liquids are stored, handled, or dispensed. [See also Figure 8.3.2(a) and Figure 8.3.2(b).] Table 8.3.2 Class I Locations Motor Fuel Dispensing Facilities Class I Location Division (Group D) Zone (Group IIA) Extent of Classified Location a Dispensing device (except overhead type) b,c Under dispenser containment 1 1 Entire space within and under dispenser pit or containment Dispenser 2 2 Within 450 mm (18 in.) of dispenser enclosure or that portion of dispenser enclosure containing liquid handling components, extending horizontally in all directions and down to grade level Outdoor 2 2 Up to 450 mm (18 in.) above grade level, extending 6 m (20 ft) horizontally in all directions from dispenser enclosure Indoor With mechanical ventilation 2 2 Up to 450 mm (18 in.) above floor level, extending 6 m (20 ft) horizontally in all directions from dispenser enclosure With gravity ventilation 2 2 Up to 450 mm (18 in.) above floor level, extending 7.5 m (25 ft) horizontally in all directions from dispenser enclosure Dispensing device (overhead type d ) Repair garage, major e (where Class I liquids or gaseous fuels are transferred or dispensed f ) (see 3.3.12.1 and 8.3.1) 1 1 Space within dispenser enclosure and all electrical equipment integral with dispensing hose or nozzle 2 2 Within 450 mm (18 in.) of dispenser enclosure, extending horizontally in all directions and down to grade level 2 2 Up to 450 mm (18 in.) above grade level, extending 6 m (20 ft) horizontally in all directions from a point vertically below edge of dispenser enclosure 1 1 Entire space within any pit, belowgrade work area, or subfloor work area that is not ventilated 2 2 Entire space within any pit, belowgrade work area, or subfloor work area that is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level (see 7.4.5.4) 2 2 Up to 450 mm (18 in.) above floor level of the room, except as noted below, for entire floor area Unclassified Unclassified Up to 450 mm (18 in.) above floor level of the room where room is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level

0 of 105 1/21/2016 7:49 AM Class I Location Specific areas adjacent to classified locations Repair garage, minor e (where Class I liquids or gaseous fuels are not transferred or dispensed f ) (see 3.3.12.2 and 8.3.1) Specific areas adjacent to classified locations Repair garage, major e (where lighter-than-air gaseous fueled g vehicles are repaired or stored) (see 3.3.12.1) Specific areas adjacent to classified locations Remote pump Division (Group D) Zone (Group IIA) Extent of Classified Location a 2 2 Within 0.9 m (3 ft) of any fill or dispensing point, extending in all directions Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure or where effectively cut off by walls or partitions 2 2 Entire space within any pit, belowgrade work area, or subfloor work area that is not ventilated 2 2 Up to 450 mm (18 in.) above floor level, extending 0.9 m (3 ft) horizontally in all directions from opening to any pit, belowgrade work area, or subfloor work area that is not ventilated Unclassified Unclassified Entire space within any pit, belowgrade work area, or subfloor work area that is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level (see 7.4.5.4) Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure, or where effectively cut off by walls or partitions 2 2 Within 450 mm (18 in.) of ceiling, except as noted below Unclassified Unclassified Within 450 mm (18 in.) of ceiling where ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 450 mm (18 in.) of the highest point in the ceiling Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure, or where effectively cut off by walls or partitions

1 of 105 1/21/2016 7:49 AM Location Division (Group D) Class I Zone (Group IIA) Extent of Classified Location a Outdoor 1 1 Entire space within any pit or box below grade level, any part of which is within 3 m (10 ft) horizontally from any edge of pump 2 2 Within 900 mm (3 ft) of any edge of pump, extending horizontally in all directions 2 2 Up to 450 m (18 in.) above grade level, extending 3 m (10 ft) horizontally in all directions from any edge of pump Indoor 1 1 Entire space within any pit Sales, storage, rest rooms (including structures [such as the attendant s kiosk] on or adjacent to dispensers) Tank, aboveground (tanks not directly related to fueling as detailed in table 8.3.2b and section 4.3.2) 2 2 Within 1.5 m (5 ft) of any edge of pump, extending in all directions 2 2 Up to 900 mm (3 ft) above floor level, extending 7.5 m (25 ft) horizontally in all directions from any edge of pump Unclassified Unclassified Except as noted below 1 1 Entire volume, if there is any opening to room within the extent of a Division 1 or Zone 1 location 2 2 Entire volume, if there is any opening to room within the extent of a Division 2 or Zone 2 location Inside tank 1 0 Entire inside volume Shell, ends, roof, dike area 1 1 Entire space within dike, where dike height exceeds distance from tank shell to inside of dike wall for more than 50 percent of tank circumference 2 2 Entire space within dike, where dike height does not exceed distance from tank shell to inside of dike wall for more than 50 percent of tank circumference 2 2 Within 3 m (10 ft) of shell, ends, or roof of tank Vent 1 1 Within 1.5 m (5 ft) of open end of vent, extending in all directions Tank, underground 2 2 Between 1.5 m and 3 m (5 ft and 10 ft) from open end of vent, extending in all directions Inside tank 1 0 Entire inside volume Fill opening 1 1 Entire space within any pit or box below grade level, any part of which is within a Division 1 or Division 2 classified location or within a Zone 1 or Zone 2 classified location 2 2 Up to 450 mm (18 in.) above grade level, extending 1.5 m (5 ft) horizontally in all directions from any tight-fill connection and extending 3 m (10 ft)

2 of 105 1/21/2016 7:49 AM Location Division (Group D) Class I Zone (Group IIA) Extent of Classified Location a horizontally in all directions from any loose-fill connection Vent 1 1 Within 1.5 m (5 ft) of open end of vent, extending in all directions Vapor processing system 2 2 Between 1.5 m and 3 m (5 ft and 10 ft) from open end of vent, extending in all directions Pits 1 1 Entire space within any pit or box below grade level, any part of which: (1) is within a Division 1 or Division 2 classified location; (2) is within a Zone 1 or Zone 2 classified location; (3) houses any equipment used to transfer or process vapors Equipment in protective enclosures Equipment not within protective enclosure 2 2 Entire space within enclosure 2 2 Within 450 mm (18 in.) of equipment containing flammable vapors or liquid, extending horizontally in all directions and down to grade level 2 2 Up to 450 m (18 in.) above grade level within 3 m (10 ft) horizontally of the vapor processing equipment Equipment enclosure 1 1 Entire space within enclosure, if flammable vapor or liquid is present under normal operating conditions 2 2 Entire space within enclosure, if flammable vapor or liquid is not present under normal operating conditions Vacuum assist blower 2 2 Within 450 mm (18 in.) of blower, extending horizontally in all directions and down to grade level 2 2 Up to 450 mm (18 in.) above grade level, extending 3 m (10 ft) horizontally in all directions Vault 1 1 Entire interior space, if Class I liquids are stored within a For marine application, grade level means the surface of a pier, extending down to water level. b Refer to Figures 8.3.2(a) and 8.3.2(b) for illustrations of classified locations around dispensing devices. c Area classification inside the dispenser enclosure is covered in UL 87, Standard for Power-Operated Dispensing Devices for Petroleum Products. d Ceiling-mounted hose reel. e The terms repair garage, major and repair garage, minor are intended to correlate with Article 511.3 of NFPA 70, National Electrical Code. For the purposes of application of this table, these terms do not include associated floor space used for offices, parking, or showrooms. f Includes draining of Class I liquids from vehicles. g Includes fuels such as hydrogen and natural gas, but not LPG. Figure 8.3.2(a) Classified Areas Adjacent to Dispensers.

3 of 105 1/21/2016 7:49 AM Figure 8.3.2(b) Classified Areas Adjacent to Dispenser Mounted on Aboveground Storage Tank. Exception: The extent of the classified area around a vacuum-assist blower shall be permitted to be reduced if the blower is specifically listed for such reduced distances. Table 8.3.2 seems to conflict with the use of an AST in conjunction with a dispensing device when it comes to the definition of hazardous zones. Table 8.3.3(b) shows zones that are not near as large as those shown for ASTs in 8.3.2 with no clear definition to the differences. The only clue is that in 8.3.2 it refers to dikes around the tanks which would seem to indicate large storage tanks. This large zone around the tank can impact the hazardous classification required for the dispenser. Submitter Full Name: RANDY MOSES Organization: WAYNE FUELING SYSTEMS LLC

4 of 105 1/21/2016 7:49 AM Submittal Date: Tue Jun 30 11:17:20 EDT 2015 Resolution: CI-17-NFPA 30A-2015 Statement: The revisions proposed in PIs 27, 53, and 74 require more review of requirements contained in NFPA 30 and NFPA 70, as well as API RP 500. This work will be considered by the task group on alternative fuels.

5 of 105 1/21/2016 7:49 AM Public Input No. 53-NFPA 30A-2015 [ Section No. 8.3.2 ]

6 of 105 1/21/2016 7:49 AM 8.3.2*

7 of 105 1/21/2016 7:49 AM Table 8.3.2 shall be used to delineate and classify areas for the purposes of installing electrical wiring and electrical utilization equipment where Class I liquids are stored, handled, or dispensed. [See also Figure 8.3.2(a) and Figure 8.3.2(b).] Table 8.3.2 Class I Locations Motor Fuel Dispensing Facilities Location Dispensing device (except overhead type) b,c Under dispenser containment Division (Group D) Class I Zone (Group IIA) Extent of Classified Location a 1 1 Entire space within and under dispenser pit or containment Dispenser 2 2 Within 450 mm (18 in.) of dispenser enclosure or that portion of dispenser enclosure containing liquid handling components, extending horizontally in all directions and down to grade level Outdoor 2 2 Up to 450 mm (18 in.) above grade level, extending 6 m (20 ft) horizontally in all directions from dispenser enclosure Indoor With mechanical ventilation 2 2 Up to 450 mm (18 in.) above floor level, extending 6 m (20 ft) horizontally in all directions from dispenser enclosure With gravity ventilation 2 2 Up to 450 mm (18 in.) above floor level, extending 7.5 m (25 ft) horizontally in all directions from dispenser enclosure Dispensing device (overhead type d ) Repair garage, major e (where Class I liquids or gaseous fuels are transferred or dispensed f ) (see 3.3.12.1 and 8.3.1) 1 1 Space within dispenser enclosure and all electrical equipment integral with dispensing hose or nozzle 2 2 Within 450 mm (18 in.) of dispenser enclosure, extending horizontally in all directions and down to grade level 2 2 Up to 450 mm (18 in.) above grade level, extending 6 m (20 ft) horizontally in all directions from a point vertically below edge of dispenser enclosure 1 1 Entire space within any pit, belowgrade work area, or subfloor work area that is not ventilated 2 2 Entire space within any pit, belowgrade work area, or subfloor work area that is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level (see 7.4.5.4)

8 of 105 1/21/2016 7:49 AM Class I Location Specific areas adjacent to classified locations Repair garage, minor e (where Class I liquids or gaseous fuels are not transferred or dispensed f ) (see 3.3.12.2 and 8.3.1) Specific areas adjacent to classified locations Repair garage, major e (where lighter-than-air Division Zone (Group D) (Group IIA) Extent of Classified Location a 2 2 Up to 450 mm (18 in.) above floor level of the room, except as noted below, for entire floor area Unclassified Unclassified Up to 450 mm (18 in.) above floor level of the room where room is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level 2 2 Within 0.9 m (3 ft) of any fill or dispensing point, extending in all directions Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure or where effectively cut off by walls or partitions 2 2 Entire space within any pit, belowgrade work area, or subfloor work area that is not ventilated 2 2 Up to 450 mm (18 in.) above floor level, extending 0.9 m (3 ft) horizontally in all directions from opening to any pit, belowgrade work area, or subfloor work area that is not ventilated Unclassified Unclassified Entire space within any pit, belowgrade work area, or subfloor work area that is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level (see 7.4.5.4) Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure, or where effectively cut off by walls or partitions 2 2 Within 450 mm (18 in.) of ceiling, except as noted below

9 of 105 1/21/2016 7:49 AM Location gaseous fueled g vehicles are repaired or stored) (see 3.3.12.1) Unclassified Division (Group D) Class I Zone (Group IIA) Unclassified Within 450 mm (18 in.) of ceiling where ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 450 mm (18 in.) of the highest point in the ceiling Extent of Classified Location a Specific areas adjacent to classified locations Remote pump Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure, or where effectively cut off by walls or partitions Outdoor 1 1 Entire space within any pit or box below grade level, any part of which is within 3 m (10 ft) horizontally from any edge of pump 2 2 Within 900 mm (3 ft) of any edge of pump, extending horizontally in all directions 2 2 Up to 450 m (18 in.) above grade level, extending 3 m (10 ft) horizontally in all directions from any edge of pump Indoor 1 1 Entire space within any pit 2 2 Within 1.5 m (5 ft) of any edge of pump, extending in all directions 2 2 Up to 900 mm (3 ft) above floor level, extending 7.5 m (25 ft) horizontally in all directions from any edge of pump Sales, storage, rest rooms (including structures [such as the attendant s attendant s kiosk] on or adjacent to dispensers) Unclassified Unclassified Except as noted below 1 1 Entire volume, if there is any opening to room within the extent of a Division 1 or Zone 1 location 2 2 Entire volume, if there is any opening to room within the extent of a Division 2 or

0 of 105 1/21/2016 7:49 AM Class I Location Division (Group D) Zone (Group IIA) Extent of Classified Location a Zone 2 location Tank, aboveground Inside tank 1 0 Entire inside volume Shell, ends, roof, dike area 1 1 Entire space within dike, where dike height exceeds distance from tank shell to inside of dike wall for more than 50 percent of tank circumference 2 2 Entire space within dike, where dike height does not exceed distance from tank shell to inside of dike wall for more than 50 percent of tank circumference 2 2 Within 3 m (10 ft) of shell, ends, or roof of tank Vent 1 1 Within 1.5 m (5 ft) of open end of vent, extending in all directions 2 2 Between 1.5 m and 3 m (5 ft and 10 ft) from open end of vent, extending in all directions Tank, underground Inside tank 1 0 Entire inside volume Fill opening 1 1 Entire space within any pit or box below grade level, any part of which is within a Division 1 or Division 2 classified location or within a Zone 1 or Zone 2 classified location 2 2 Up to 450 mm (18 in.) above grade level, extending 1.5 m (5 ft) horizontally in all directions from any tight-fill connection and extending 3 m (10 ft) horizontally in all directions from any loose-fill connection Vent 1 1 Within 1.5 m (5 ft) of open end of vent, extending in all directions 2 2 Between 1.5 m and 3 m (5 ft and 10 ft) from open end of vent, extending in all directions Vapor processing system Pits 1 1 Entire space within any pit or box below grade level, any part of which: (1) is within a Division 1 or Division 2 classified location; (2) is within a Zone 1 or Zone 2 classified location; (3) houses any equipment used to transfer or process vapors Equipment in protective enclosures 2 2 Entire space within enclosure Equipment not within protective enclosure 2 2 Within 450 mm (18 in.) of equipment containing flammable vapors or liquid, extending horizontally in all directions

1 of 105 1/21/2016 7:49 AM Class I Location Division Zone (Group D) (Group IIA) Extent of Classified Location a and down to grade level 2 2 Up to 450 m (18 in.) above grade level within 3 m (10 ft) horizontally of the vapor processing equipment Equipment enclosure 1 1 Entire space within enclosure, if flammable vapor or liquid is present under normal operating conditions 2 2 Entire space within enclosure, if flammable vapor or liquid is not present under normal operating conditions Vacuum assist blower 2 2 Within 450 mm (18 in.) of blower, extending horizontally in all directions and down to grade level 2 2 Up to 450 mm (18 in.) above grade level, extending 3 m (10 ft) horizontally in all directions Vault 1 1 Entire interior space, if Class I liquids are stored within a For marine application, grade level means the surface of a pier, extending down to water level. b Refer to Figures 8.3.2(a) and 8.3.2(b) for illustrations of classified locations around dispensing devices. c Area classification inside the dispenser enclosure is covered in UL 87, Standard for Power-Operated Dispensing Devices for Petroleum Products. d Ceiling-mounted hose reel. e The terms repair garage, major and repair garage, minor are intended to correlate with Article 511.3 of NFPA 70, National Electrical Code. For the purposes of application of this table, these terms do not include associated floor space used for offices, parking, or showrooms. f Includes draining of Class I liquids from vehicles. g Includes fuels such as hydrogen and natural gas, but not LPG. Figure 8.3.2(a) Classified Areas Adjacent to Dispensers.

2 of 105 1/21/2016 7:49 AM Figure 8.3.2(b) Classified Areas Adjacent to Dispenser Mounted on Aboveground Storage Tank. Exception: The extent of the classified area around a vacuum-assist blower shall be permitted to be reduced if the blower is specifically listed for such reduced distances. The intent here is to delete reference to gaseous fuels in Table 8.3.2. Hope Terra shows that correctly. Section 8.3.2 refers only to class I liquids not gaseous fuels so the table exceeds its charging statement (8.3.2) by including gaseaous fuels. Also the requirements for hydrogen are included in NFPA 2. Submitter Full Name: MARTIN GRESHO Organization: FP2 FIRE INC

3 of 105 1/21/2016 7:49 AM Submittal Date: Wed Jul 01 19:35:43 EDT 2015 Resolution: CI-17-NFPA 30A-2015 Statement: The revisions proposed in PIs 27, 53, and 74 require more review of requirements contained in NFPA 30 and NFPA 70, as well as API RP 500. This work will be considered by the task group on alternative fuels.

4 of 105 1/21/2016 7:49 AM Public Input No. 74-NFPA 30A-2015 [ Section No. 8.3.2 ]

5 of 105 1/21/2016 7:49 AM 8.3.2*

6 of 105 1/21/2016 7:49 AM Table 8.3.2 shall be used to delineate and classify areas for the purposes of installing electrical wiring and electrical utilization equipment where Class I liquids are stored, handled, or dispensed. [See also Figure 8.3.2(a) and Figure 8.3.2(b).] Table 8.3.2 Class I Locations Motor Fuel Dispensing Facilities Location Dispensing device (except overhead type) b,c Under dispenser containment Division (Group D) Class I Zone (Group IIA) Extent of Classified Location a 1 1 Entire space within and under dispenser pit or containment Dispenser 2 2 Within 450 mm (18 in.) of dispenser enclosure or that portion of dispenser enclosure containing liquid handling components, extending horizontally in all directions and down to grade level Outdoor 2 2 Up to 450 mm (18 in.) above grade level, extending 6 m (20 ft) horizontally in all directions from dispenser enclosure Indoor With mechanical ventilation 2 2 Up to 450 mm (18 in.) above floor level, extending 6 m (20 ft) horizontally in all directions from dispenser enclosure With gravity ventilation 2 2 Up to 450 mm (18 in.) above floor level, extending 7.5 m (25 ft) horizontally in all directions from dispenser enclosure Dispensing device (overhead type d ) Repair garage, major e (where Class I liquids or gaseous fuels are transferred or dispensed f ) (see 3.3.12.1 and 8.3.1) 1 1 Space within dispenser enclosure and all electrical equipment integral with dispensing hose or nozzle 2 2 Within 450 mm (18 in.) of dispenser enclosure, extending horizontally in all directions and down to grade level 2 2 Up to 450 mm (18 in.) above grade level, extending 6 m (20 ft) horizontally in all directions from a point vertically below edge of dispenser enclosure 1 1 Entire space within any pit, belowgrade work area, or subfloor work area that is not ventilated 2 2 Entire space within any pit, belowgrade work area, or subfloor work area that is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level (see 7.4.5.4) 2 2 Up to 450 mm (18 in.) above floor level of the room, except as noted below, for entire floor area Unclassified Unclassified Up to 450 mm (18 in.) above floor level of the room where room is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level

7 of 105 1/21/2016 7:49 AM Class I Location Specific areas adjacent to classified locations Repair garage, minor e (where Class I liquids or gaseous fuels are not transferred or dispensed f ) (see 3.3.12.2 and 8.3.1) Specific areas adjacent to classified locations Repair garage, major e (where lighter-than-air gaseous fueled g vehicles are repaired or stored) (see 3.3.12.1) Specific areas adjacent to classified locations Remote pump Division (Group D) Zone (Group IIA) Extent of Classified Location a 2 2 Within 0.9 m (3 ft) of any fill or dispensing point, extending in all directions Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure or where effectively cut off by walls or partitions 2 2 Entire space within any pit, belowgrade work area, or subfloor work area that is not ventilated 2 2 Up to 450 mm (18 in.) above floor level, extending 0.9 m (3 ft) horizontally in all directions from opening to any pit, belowgrade work area, or subfloor work area that is not ventilated Unclassified Unclassified Entire space within any pit, belowgrade work area, or subfloor work area that is provided with ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 300 mm (12 in.) of floor level (see 7.4.5.4) Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure, or where effectively cut off by walls or partitions 2 2 Within 450 mm (18 in.) of ceiling, except as noted below Unclassified Unclassified Within 450 mm (18 in.) of ceiling where ventilation of at least 0.3 m 3 /min/m 2 (1 ft 3 /min/ft 2 ) of floor area, with suction taken from a point within 450 mm (18 in.) of the highest point in the ceiling Unclassified Unclassified Areas adjacent to classified locations where flammable vapors are not likely to be released, such as stock rooms, switchboard rooms, and other similar locations, where mechanically ventilated at a rate of four or more air changes per hour or designed with positive air pressure, or where effectively cut off by walls or partitions Outdoor 1 1 Entire space within any pit or box below grade level, any part of which is within 3 m (10 ft) horizontally from any edge of pump

8 of 105 1/21/2016 7:49 AM Location Division (Group D) Class I Zone (Group IIA) Extent of Classified Location a 2 2 Within 900 mm (3 ft) of any edge of pump, extending horizontally in all directions 2 2 Up to 450 m (18 in.) above grade level, extending 3 m (10 ft) horizontally in all directions from any edge of pump Indoor 1 1 Entire space within any pit 2 2 Within 1.5 m (5 ft) of any edge of pump, extending in all directions 2 2 Up to 900 mm (3 ft) above floor level, extending 7.5 m (25 ft) horizontally in all directions from any edge of pump Sales, storage, rest rooms Unclassified Unclassified Except as noted below (including structures [such as the attendant s kiosk] on or adjacent to dispensers) Tank, aboveground 1 1 Entire volume, if there is any opening to room within the extent of a Division 1 or Zone 1 location 2 2 Entire volume, if there is any opening to room within the extent of a Division 2 or Zone 2 location Inside tank 1 0 Entire inside volume Shell, ends, roof, dike area 1 1 Entire space within dike, where dike height exceeds distance from tank shell to inside of dike wall for more than 50 percent of tank circumference 2 2 Entire space within dike, where dike height does not exceed distance from tank shell to inside of dike wall for more than 50 percent of tank circumference 2 2 Within 3 m (10 ft) of shell, ends, or roof of tank Vent 1 1 Within 1.5 m (5 ft) of open end of vent, extending in all directions 2 2 Between 1.5 m and 3 m (5 ft and 10 ft) from open end of vent, extending in all directions Tank, underground Inside tank 1 0 Entire inside volume Fill opening 1 1 Entire space within any pit or box below grade level, any part of which is within a Division 1 or Division 2 classified location or within a Zone 1 or Zone 2 classified location 2 2 Up to 450 mm (18 in.) above grade level, extending 1.5 m (5 ft) horizontally in all directions from any tight-fill connection and extending 3 m (10 ft) horizontally in all directions from any loose-fill connection Vent 1 1 Within 1.5 m (5 ft) of open end of vent, extending in all directions 2 2 Between 1.5 m and 3 m (5 ft and 10 ft) from open end of vent, extending in all directions

9 of 105 1/21/2016 7:49 AM Location Division (Group D) Class I Zone (Group IIA) Extent of Classified Location a Vapor processing system Pits 1 1 Entire space within any pit or box below grade level, any part of which: (1) is within a Division 1 or Division 2 classified location; (2) is within a Zone 1 or Zone 2 classified location; (3) houses any equipment used to transfer or process vapors Equipment in protective enclosures 2 2 Entire space within enclosure Equipment not within protective enclosure 2 2 Within 450 mm (18 in.) of equipment containing flammable vapors or liquid, extending horizontally in all directions and down to grade level 2 2 Up to 450 m (18 in.) above grade level within 3 m (10 ft) horizontally of the vapor processing equipment Equipment enclosure 1 1 Entire space within enclosure, if flammable vapor or liquid is present under normal operating conditions 2 2 Entire space within enclosure, if flammable vapor or liquid is not present under normal operating conditions Vacuum assist blower 2 2 Within 450 mm (18 in.) of blower, extending horizontally in all directions and down to grade level 2 2 Up to 450 mm (18 in.) above grade level, extending 3 m (10 ft) horizontally in all directions Vault 1 1 Entire interior space, if Class I liquids are stored within a For marine application, grade level means the surface of a pier, extending down to water level. b Refer to Figures 8.3.2(a) and 8.3.2(b) for illustrations of classified locations around dispensing devices. c Area classification inside the dispenser enclosure is covered in UL 87, Standard for Power-Operated Dispensing Devices for Petroleum Products. d Ceiling-mounted hose reel. e The terms repair garage, major and repair garage, minor are intended to correlate with Article 511.3 of NFPA 70, National Electrical Code. For the purposes of application of this table, these terms do not include associated floor space used for offices, parking, or showrooms. f Includes draining of Class I liquids from vehicles. g Includes fuels such as hydrogen and natural gas, but not LPG. Figure 8.3.2(a) Classified Areas Adjacent to Dispensers.

0 of 105 1/21/2016 7:49 AM Figure 8.3.2(b) Classified Areas Adjacent to Dispenser Mounted on Aboveground Storage Tank. Exception: The extent of the classified area around a vacuum-assist blower shall be permitted to be reduced if the blower is specifically listed for such reduced distances. The start of 8.3.2, clearly states that Table 8.3.2 "where Class I liquids are stored, handled, or dispensed." Therefore, all references to gaseous fuels should be deleted. The electrical classification requirements for gaseous fuels are listed in NFPA52 (CNG) and NFPA2 (Hydrogen) and the requirements for gaseous fuels in 8.3.2 creates a conflict Submitter Full Name: SPENCER QUONG Organization: QUONG ASSOCIATES INC Affilliation: TOYOTA

2024 © homedocbox.com Privacy Policy | Terms of Service | Feedback