Enter Program Program Location 1. Hold 8 key for 3 seconds, keypad will beep 2. Enter 4 5 6 7 8 9, display should show dash on display 1. Press [B/A] key display will show 3 dashs 2. Enter 3-digit location (use B/A for any 0) 3. Value currently programmed in location will display 4. Scroll Value UP with 4 key, scroll Value DOWN with 7, blank location with 5 5. When display shows desired Value press 2 to move to next location (Or B/A + 3-digit location to move to elsewhere) Programming with LCD layout is slightly different LCD Keypads 1 scrolls left 2 scrolls right 5 scrolls data up 9 scrolls data down Exit Program Enable Panics Lockout Bypass 1. Hold 8 key 3 seconds, keypad will flash and beep 2. Enter 4 5 6 7 8 9, display should return to normal Open Keypad cover, cute Jumper "E" (bottom left jumper, clearly marked) 1. Run jumper to pins on large chip marked X (see wiring diagram) 2. Press 9 for 3 seconds, then 8 for 3 seconds and enter 456789 3. LED display should show ---, remove jumper and program normallly (wire MUST be removed to view or change locations) Report Codes Zone 1 31 Duress 21 to 29 Zone 2 32 Keypad Fire Panic 19 Zone 3 33 Keypad Police Panic 29 Zone 4 34 Keypad Medical Panic 49 Zone 5 35 Low Battery 78 Zone 6 36 Low Battery Restoral 98 Zone 7 37 AC Failure 79 Zone 8 38 AC Failure Restoral 99 Zone 9 39 Fire Trouble 76 Zone 10 41 Fire Restore 96 Zone 11 42 Smoke Detector* 16 or 18 Zone 12 43 Cancel D1 to D8 Zone 13 44 Opening 5 + User Zone 14 45 Closing 6 + User Zone 15 46 Test/Download Complete EE Zone 16 47 Zone Restores 9 + Zone IF something screws up power down then up, you have 30 seconds to get into programming
-------------------------------------------------< Report Options >------------------------------------------------- To program REPORT OPTIONS in locations 166 to 185 see below Diagram Add location together and enter sum in location Example: Enable Reporting for Zones 1 to 6, Keypad Panic, Fire, Duress, Fire Trouble, AC Fail and Low Bat 1. Press B/A then 1 6 6 to move to Location 166 2. Add ZONE 1 (1) + ZONE 2 (2) + ZONE 3 (4) + ZONE 4 (8) = 15 or F, enter the F in location 166 3. Press 2 key to move to 167 4. Add Zone 5 (1) + Zone 6 (2) + Keypad Panic (8) = 11 (B), enter the B in location 167 5. Press 2 key to move to 168 6. Add FIRE ZONE (1) + AMBUSH (2) + FIRE TROUBLE (4) = 7, enter the 7 in location 168 7. Press 2 key to move to 169 8. Add AC FAIL (2) + LOW BAT (4) = 6, enter the 6 in location 169 Report Enable Zone 1 to 4 I F _I Fire/Duress, Fire Trouble I 7 I 166 168 Report Enable Zones 5, 6 & Panic I B _I AC Fail/Low Bat Trouble I 6 I 167 169 Restores Enabled I I I Misc Restores I I I (Blank out this section) 170 171 (Blank out this section) 172 173 Zone Restores I I I (Blank out this section) 184 185 -------------------------------------------------< Report Codes >------------------------------------------------- Zone 1 Report Code I 3 I 1 I Keypad Police Panic I 2 I 9 I 000 001 014 015 Zone 2 Report Code I 3 I 2 I Fire Panic/Smoke Detector* I 1 I 6 I 002 003 016 017 Zone 3 Report Code I 3 I 3 I Hostage/Duress I 2 I 6 I 004 005 018 019 Zone 4 Report Code I 3 I 4 I Fire Trouble I 7 I 6 I 006 007 020 021 Zone 5 Report Code I 3 I 5 I Day Zone Trouble I I I 008 009 022 023 Zone 6 Report Code I 3 I 6 I Test Timer I I I 010 011 024 025 Not Used I I I AC Failure I 7 I 9 I 012 013 026 027 Low Battery I 7 I 8 I (I I I = Blank out Locations with 5 key) 028 029 *Fire Panic and Smoke Detector share signal if Smoke Detector uses dedicated Fire Zone -------------------------------------------------< Restore Codes >------------------------------------------------- Zone 1 Restore I I I Fire Panic/Smoke I I I 040 041 056 057 Zone 2 Restore I I I Not Used I I I 042 043 058 059 Zone 3 Restore I I I Fire Trouble I I I 044 045 060 061 Zone 4 Restore I I I Medical Panic I 4 I 9 I 046 047 062 063 Zone 5 Restore I I I Not Used I I I 048 049 064 065 Zone 6 Restore I I I AC Trouble Restore I I I 050 051 066 067 Low Battery Restore I I I (I I I = Blank out Locations with 5 key) 068 069
-----------------------------------------< Opening/Closings/Cancel >------------------------------------------ Closing User 1 I I I Opening User 1 I D I 1 I 030 031 070 071 Closing User 2 I I I Opening User 2 I D I 1 I 032 033 072 073 Closing User 3 I I I Opening User 3 I D I 1 I 034 035 074 075 Closing User 4 I I I Opening User 4 I D I 1 I 036 037 076 077 Force Arm I I I (These are Cancels, see also section 179) 038 039 Select User Closings I I Select User Openings I I 174 176 (I I I = Blank out Locations with 5 key) -----------------------------------------------< Account Numbers >----------------------------------------------- Telephone Number 1 (Last 4 of Account must be entered in each section) Group 1 Account Group 2 Account Open/Close Account I? I? I? I? I I? I? I? I? I I I I I I 100 101 102 103 104 105 106 107 108 109 110 111 Telephone Number 2 (Leave Blank) Group 1 Account Group 2 Account Open/Close Account I I I I I I I I I I I I I I I 132 133 134 135 136 137 138 139 140 141 142 143 ------------------------------------------------< Phone Numbers >------------------------------------------------ Report Format Phone 1 I 9 I 2 I 112 113 First Digit Second Digit Blank = Ademco/Silent Knight Slow Blank = Extended or Single Digit 1 = Sescoa, Vertex, DCI, Franklin 1 = Single Digit 2 = Radionics Fast 2 = 2-Digit (4/2) 3 = Silent Knight Fast 4 = Sumcheck 4 = Radionics, DCI, Franklin Slow 5 = Universal Hi Speed 8 = 2300 Handshake (Add this to above numbers) Receiver 1 Options I I I (Add D in 114 if delay needed to dial out) 114 115 (Add 9 in 115 if 9 is needed to dial out) Receiver 1 Phone I_ E_ I I I I I I I I I I I I I I I I 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 Report Format Phone 2 I I I (Leave blank) 144 145 Receiver 2 Options I I I (Leave blank) 146 147 Receiver 2 Phone I_ E_ I I I I I I I I I I I I I I I I 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 Rings before Download I 9 I (9 rings until Answer) 269 Download Phone 1 I I I I I I I I I I I I I I I I I 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 Download Phone 2 I I I I I I I I I I I I I I I I I 286 297 288 289 290 291 292 293 294 295 296 297 298 299 300 301
------------------------------------------------< Misc Functions >-------------------------------------------------- To program sections 084 to 216 see below Diagram Add location together and enter sum in location Example: Program Zones 1, 3 4, 5 and 6 for Door Chime 1. Press B/A then B/A again then 8 8 to enter Location 088 2. Add Zone 1 (1) + Zone 2 (2) + Zone 4 (8) = 11 or B, enter B in location 088 3. Press 2 key to move to 089 4. Add Zone 5 (1) + Zone 6 (2) = 3, enter 3 in location 089 Swinger Shutdown I F I 3 I (Swinger enabled on all Zones) 084 085 No EOL Zone Resistors I I I (F 3 = No EOL all Zones, Blank = EOL all zones) 086 087 Chime Zones 1 to 6 I I I (Turns on/off chimes per zone) 088 089 Never Arm I I I (Leave blank) 090 091 PIR Zone I I I (Program PIR zones here. also see 206-207) 092 093 Untimed Output to Lug E15 I F I B _I I I (Normally not programmed) 096 097 098 099 Keypad Sounder on Alarm I I I (Leave blank) 164 165 Day Zone I I I (Leave blank) 186 187 Priority Zone W/Bypass I I I (Leave blank) 188 189 Priority Zone I F I 3 I (Default = F 3, leave alone) 190 191 Remove Auto-Bypass I I I (Leave blank) 192 193 Selective Bypass I F I 3 I (Default = F 3, leave alone) 194 195 Group Bypass I? I? I (Any zone here will bypass by B/A key twice) 196 197 24 Hr Protection I I 8 I (Use if Hold-Up buttons on a zone) 198 199 Auto Reset I F I D I (Default = F D, leave alone) 200 201 Entry/Exit Delay 1 Zones I? I? I (Program which zones are Delay 1) 202 203 Entry/Exit Delay 2 Zones I? I? I (Program which zones are Delay 2) 204 205 Interior Follower Zones I? I? I (Program PIR zones here. also see 092-093) 206 207 Abort Delay per Zone I I I (Leave blank) 208 209 Burglary Output per Zone I F I B I (FB = Audible Keypad Panic, F3 = Silent) 210 211 Timed Negative Output I I I (Leave blank) 212 213 7ms Loop Response I I I (Leave blank) 214 215 50ms Loop Response I I I (Leave blank) 216 217
Hostage/Duress Code User Program Code Installer/Dealer Code ------------------------------------------------< User Codes >------------------------------------------------- I 9 I 9 I 304 305 I 1 I 2 I 3 I 4 I 5 I 6 I 306 307 308 309 310 311 This allows customer to change User codes, leave at default I 4 I 5 I 6 I 7 I 8 I 9 I 312 313 314 315 316 317 User Code 1 I 1 I 2 I 3 I 4 I User Code 2 I I I I I User Code 3 I I I I I 318 319 320 321 322 323 324 325 326 327 328 329 User Code 4 I I I I I User Code 5 I I I I_ 7 I User Code 6 I I I I I 330 331 332 333 334 335 336 337 338 339 340 341 User Code 7 I I I I I User Code 8 I I I I I 342 343 344 345 346 347 348 349 User Codes can be 1, 2, 3 or 4 digits, If User Code 5 is Quick Arm program as 7, customer can Arm system by pressing 7, do NOT make it anything else or it will screw up other functions! -------------------------------------------------< Misc Options >------------------------------------------------- Add each section, place total in box (Example: 1 + 4 + 8 = 13 or "D") I I = Blank Out with 5 key I 4 I ç 1 = Display Day Zone/Reset I 2 I ç 1 = Audible Test on Arming 078 2 = Reserved 180 2 = Auto-Reset after Timeout 4 = User 5 Quick Arm 4 = Reserved 8 = User 5 Report as User 1 8 = Reserved I I ç 1 = User 5 Service Code I 5 I ç 1 = Pulsing Fire 079 2 = Disable Day Zone Report 181 2 = Disable Key 9 Reset Fire Zone 4 = Users 6,7,8 Report as 2,3,4 4 = Enable Keypad Tactical Beeps 8 = Reserved 8 = Reset Test Timer on any Alarm Report I 1 I ç 1 = Disable Low Battery Display* I 6 I ç 1 = Disable Fault Find 080 2 = Reserved 182 2 = Enable Keypad Panic 4 = Disable Callback Download 4 = Enable Communicator Test 8 = Disable Function 6 Download 8 = Disable Bell Test I 1 I ç 1 = Watch on With Group Bypass I 1 I ç 1 = Display any Bypass 081 2 = Chime On with Group Bypass 183 2 = Reserved 4 = Display Open Zones 4 = Inc Manl Bypass in Force Arm/Status 8 = Disable Display Bypass 8 = Keyswitch Input on Zone 5 I D I ç 1 = Enable Download w/ans Machine I 6 I ç 1 = Enable User 8 to PGM Lug 082 2 = Reserved 236 2 = Enable PGM on E/E Delay 4 = Enable Keypad Fire Panic* 4 = Fail to Communicate on PGM Lug 8 = Enable Keypad Aux/Medical Panic* 8 = Keypad Sounder on PGM Lug I 2 I ç 1 = Touchtone Dialing I I ç 1 = Ground Start on PGM Lug 178 2 = Touchtone with Rotary Backup 237 2 = Armed LED on PGM Lug 4 = Backup Reporting 4 = Keypad Aux on PGM Lug 8 = Double Reporting 8 = Audio Verification on PGM Lug I 1 I ç 1 = Opening after Alarm (see 070 to 077) *Panics only work if Jumper E on Keypad is cut 179 2 = Force Arm (Jumper E found at bottom left in back of Keypad) 4 = Status Report ** Panel tends to display low battery if siren sounds 8 = Split Report for any length of time
-------------------------------------------------< System Times >------------------------------------------------- Entry/Exit Times found by dividing desired time by 16 Enter 1st digit of resut in second box and 2nd digit of result in 1st box (wierd ain't it?) Sensor Watch I _I I (Leave both blank, not used) 094 095 Exit Delay I C I 3 I (60 seconds) 218 219 Entry Delay 1 I E I 1 I (30 seconds) 220 221 Entry Delay 2 I E I 1 I (30 seconds) 222 223 Burg Timeout I 6 I I (6 minutes, leave 2nd entry blank) 224 225 Fire Timout I F I I (Unlimited, leave 2nd entry blank) 228 229 Chime Duration I 4 I I (1/2 second Chime, leave 2nd entry blank) 230 231 Abort Delay I I I (Leave both blank, not used) 232 233 Test Timer I I I (Leave both blank, not used) 250 251 Auto Download ID I I I (Leave both blank, not used) 252 253 Callback Select I I (Leave blank, not used) 254
Monitronics Napco 1000e Quick Reference Guide Monitoring and Service call 1-800-447-9239 Arming With STATUS light steady enter User Code, ARM light should turn on indicating system is armed If display shows a flashing P system was armed with a zone open Disarming / Silencing an Alarm Instant Doors Zone Bypassing User Codes Enter 4-digit Code If silencing alarm turn off siren with User Code then hold 9 for three seconds to stop any flashing display Before or after arming system press 4 for 3 seconds STATUS light will rapidly flash and all entry doors will now be instant All zones return to normal when system is disarmed. Press [B/A] + Zone to bypass (1 to 6), BYPASS light will turn on, arm system normally When system is disarmed all bypassed Zones will return to normal. Press 8 for 3 seconds (keypad will beep) Enter User Programming Code (ARM, STATUS and BYPASS lights flash and keypad rapidly beeps) Enter User to add or change (1 to 8) Enter new 3 to 4-digit User Code When finished press [B/A] twice to exit To erase a code follow above steps but press [B/A] twice instead of entering a code Door Chimes Press 5 for 3 seconds, repeat this to turn off chimes Smoke Detector Reset Trouble Light Panic Buttons Silence siren with User Code Press 9 for 3 seconds, smoke detector should reset With any internal problem ARM, STATUS and BYPASS lights will flash and a number will appear 1 = Power Failure: System is operating on Backup Battery 2 = Low Battery: Backup Battery is low and needs to either recharge or be replaced. 3 = Failure to Communicate: System cannot communicate with Monitoring Station Press 9 and # for Fire, [*/P] and # for Police, [B/A] and # for Medical Note: You may have to arm and disarm system to turn off siren after using Panic Buttons