W71E - W101E Manual / Handbuch Spare parts list / Ersatzteilliste Equipment Imp.-Exp. GmbH Zitterpappelweg 9 D - 22391 Hamburg Tel.: + 49 40 60009468-0 Fax: + 49 40 536 75 01 E - M a i l : i n f o @ w e s c o - n a v y. c o m w w w. w e s c o - n a v y. c o m
Please connect BOTH water inlets. If you have no warm water, please connect BOTH to cold water!!!
Maintenance instruction of the machine 7 WARNING To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply. End of day Clean AC drive filter: a. Snap off external plastic cover which contains filter. b. Remove foam filter from cover. c. Wash filter with warm water and allow to air dry. Filter can be vacuumed clean. General maintenance Clean the entire cabinet of the machine regularly and remove all traces of soap, etc... Remove all detergent residue in the soap dispenser with hot water. Clean the door gasket and remove all detergents and other products. Shut off the main water, steam, and power connections at the end of each day. Do not change the setting of the water inlet taps on boiler fed machines once these have been installed. It is recommended to leave the door and soap dispenser open after use, to ventilate the machine. Check for proper door lock operation on a daily basis. Periodical maintenance The V-belts of the motors should be retightened after two to three months when first used. This is necessary because these belts are subject to a one-time stretching when first used. If this is not done, the belt starts to slip after a few months and will break shortly afterwards. Check the water inlet filters to make sure they are not blocked by calcification. Check the drain valve for obstructions. If a machine frequently skips the final spin, check whether the probe of the out of balance switch is still in the appropriate position, that is horizontally centered and vertically 1/3 from the bottom inside the window. (When the drum is empty). Important B - Clean the drainpipe every 6 months in case drain (B) is used. - The water still being in the drain needs to be drained using drain (A) before cleaning the drainpipe or replacing the exhaust valve. A Label 16
MICRO 20 Note: when a malfunction occours during a program, the central display will communicate the appropriate error message at the end of the cycle. When the malfunction has been corrected and a new program selected, the error message will disappear. When error codes E6,E7,E9 or Eb are detected at the start of a cycle, the program will not start and the error messge will remain on display until the problem is corrected. ERROR CODE PROBABLE CAUSE CORRECTIVE ACTION E3 OPL Models The E prom is defective, Replace the E Prom E3 Coin Models If a program number appears on the right display in combination with E3. This indicates a incorrect Correct Coin value adjustment price adjustment for this program. A coin value of "0" or larger tham "1000" was programmed. E4 (water level) Water level was not reached after 15 minutes Check, Inlet Water supply, Inlet Water Valves, Drain Valve, Water Level Switch. E5 (heating) Programmed temperature was not reached Check, auxcillary heating system, after 80 minutes temperature sensor, water safety level switch. E6 (door lock) The door lock was released during the wash cycle Check, door lock circuit, Door lock mechanism. E7 ( safety level) The water was not drained, machine did not spin. Check, drain valve, drain outlet. E8 (temperature sensor) Defective sensor or temperature sensor circuit. Replace temperature sensor, repair wiring circuit. E9 (motor protection) The thermo-magnetic protection was activated Check, motor, motor conections, contactors, 5 times, high motor current. input voltage, inverter, motor and machine bearings, excessive foam left in cylinder after rinsing. EA (tilt switch) Tilt switch was activated 15 times, final spin was Check, load size, load type, drain valve. skipped. Unbalanced load. Eb ( tilt switch) Tilt switch is activated at start of cycle. Correct problem. Mot 2 (Rotation sensor) Defective rotation sensor, or wiring to sensor. Replace rotation sensor, correct wiring. C:\Dokumente und Einstellungen\loock\Lokale Einstellungen\Temporary Internet Files\OLK19DC\Micro-20 error codes
'"(#)* & + ", P P!" # E " $%&!"" 1
S P P %! " -. +"" ")(." +/! " (! " 0$1-!""." " " ( 2
E E E "! 0! 2 & "" "! ((( (( (( "! 3" "! & "" 3
E E E "! 1" " " "" & "" "! 0 "! " & "" "! 4" " " " & "" 4
E I I +!""5 "!"!!!!"! " " "6%6* 7557!"! "5 78 "! "55!" 5
I 75572!""5 7# "! ""! " "5! I 75579!""5 7: "!!5!""! "" "5! E "55 "5 "!!!5"" "."!5!"5"!" ""!"! +5 7 /! "- / 5!"!"5; "! 6
E E E " (9!" "5: / / "!"& 1" /7# " "5 &!"": &!"": 7
E E E &!"": &!"": &!"": 8
P " " / "! ((( (( ((!"!""5" 5" " ". 5" / "!"!4$ "! ((( (( (( "!""5 9
1" "! 0$< " "!".! ""!"! 1&&3!" + "! $=1!!""!> 10
Prewash LED - Out of balance switch (NC) Mainwash LED Rinse 1 LED - Coin 1 (NO) Rinse 2 LED - Coin 2 (NO) Rinse 3 LED - Speed sensor Last rinse LED - Thermo overload (NO) Spin action LED s P " "! 7 &! 11