Simply Engineered Better Technical Manual Undercounter Dishwasher Model 0-HTM PLUS 0-HTNM PLUS 0-LTM PLUS Machine Serial No. September, 00 Manual P/N 006 67 N. Service Road Jordan Station, Ontario, Canada L0R S0 Moyer Diebel, Ltd. 90/6-9 Fax: 90/6-6
Complete the information below so it will be available for quick reference. Model Number Serial Number Voltage and Phase Moyer Diebel Parts Distributor Phone (if applicable) Moyer Diebel Service Agency Phone Moyer Diebel Service: Moyer Diebel Limited Phone: -90-6-9-00-6-79 Fax: -90-6-6 TE: When calling to order parts, be sure to have the model number, serial number, voltage, and phase of your machine, along with your customer account number. COPYRIGHT 00 by Moyer Diebel
REVISIONS Revision History Revision Revised Serial Number Comments Date Pages Effectivity 7/6/0 All Issue of manual and replacement parts lists.
THIS PAGE INTENTIONALLY LEFT BLANK
CONTENTS CONTENTS Page INTRODUCTION... WARRANTY... GENERAL... INSTALLATION... Unpacking... Electrical Connections... Plumbing Connections... 6 Detergent... 6 Rinse-Aid... 6 Chemical Sanitizer... 6 Completing Installation... 7 OPERATION... Operation Summary... Operation Procedures... MAINTENAE... 0 Cleaning Schedule... 0 Deliming... Deliming Process... Maintenance Schedule... TROUBLESHOOTING... REPLACEMENT PARTS... ELECTRICAL DIAGRAMS... 9 TIMER CHARTS AND DIAGRAMS... LIST OF FIGURES Figure Track and Panel Assembly... 6 Figure Door and Switch Assembly... Figure Tank/Drain Assembly... 0 Figure Pump Assembly... Figure Wash System Assembly... Figure 6 Booster Assembly and Water Inlet Piping (HT PLUS Only)... 6 Figure 7 Water Inlet Piping (HTN PLUS, LT PLUS Only)... Figure Fill System... 0
CONTENTS Figure 9 Detergent Pump Assembly... Figure 0 Sanitizer/Rinse-Aid Pump Assembly... Figure Control Panel Assembly... 6 Figure Electrical Diagram, 0-HT PLUS... 0 Figure Electrical Diagram, 0-HTN PLUS... Figure Electrical Diagram, 0-LT PLUS... Figure Timer Chart and Diagram, 0-HT PLUS... Figure 6 Timer Chart and Diagram, 0-LT PLUS...
INTRODUCTION INTRODUCTION Welcome to Moyer Diebel. Thank you for choosing Moyer Diebel and for allowing us to take care of your dishwashing needs. This manual covers several models. Model numbers are shown on the front cover. Your machine has been completely assembled, inspected, and thoroughly tested at our factory to eliminate problems at installation before it was shipped to your installation site. This manual provides: Warranty information Installation and operation procedures Maintenance instructions Troubleshooting guide Replacement parts lists. Complete and return your warranty registration card as soon as possible. Moyer Diebel constantly improves its products; therefore, specifications contained in this manual may have changed. For your protection, factory authorized parts should always be used. Replacement parts may be ordered from your Moyer Diebel authorized parts distributor or service agency. When ordering parts, supply the model number, serial number, voltage and phase of your machine, the part number, part description, and quantity.
WARRANTY LIMITED WARRANTY Champion Industries/Moyer Diebel Limited, P.O. Box, Winston-Salem, North Carolina 7, and P. O. Box 0, 67 North Service Road, Jordan Station, Ontario, Canada L0R S0 warrants machines, and parts, as set out below. Warranty of Machines: Champion Industries/Moyer Diebel Limited warrants all new machines of its manufacture bearing the name Champion or "Moyer Diebel" and installed within the United States and Canada to be free from defects in material and workmanship for a period of one () year after the date of installation or fifteen () months after the date of shipment by Champion/Moyer Diebel, whichever occurs first. [See below for special provisions relating to Model Series DF and SW.] The warranty registration card must be returned to Champion/Moyer Diebel within ten (0) days after installation. If warranty card is not returned to Champion/Moyer Diebel within such period, the warranty will expire after one year from the date of shipment. Champion/Moyer Diebel will not assume any responsibility for extra costs for installation in any area where there are jurisdictional problems with local trades or unions. If a defect in workmanship or material is found to exist within the warranty period, Champion/Moyer Diebel, at its election, will either repair or replace the defective machine or accept return of the machine for full credit; provided, however, as to Model Series DF and SW, Champion/Moyer Diebel's obligation with respect to labor associated with any repairs shall end (a) 0 days after shipment, or (b) 90 days after installation, whichever occurs first. In the event that Champion/Moyer Diebel elects to repair, the labor and work to be performed in connection with the warranty shall be done during regular working hours by a Champion/Moyer Diebel authorized service technician. Defective parts become the property of Champion/Moyer Diebel. Use of replacement parts not authorized by Champion/Moyer Diebel will relieve Champion/ Moyer Diebel of all further liability in connection with its warranty. In no event will Champion/Moyer Diebel's warranty obligation exceed Champion/Moyer Diebel's charge for the machine. The following are not covered by Champion/Moyer Diebel's warranty: a. Lighting of gas pilots or burners. b. Cleaning of gas lines. c. Replacement of fuses or resetting of overload breakers. d. Adjustment of thermostats. e. Adjustment of clutches. f. Opening or closing of utility supply valves or switching of electrical supply current. g. Adjustments to chemical dispensing equipment. h. Cleaning of valves, strainers, screens, nozzles, or spray pipes. i. Performance of regular maintenance and cleaning as outlined in operator s guide. j. Damages resulting from water conditions, accidents, alterations, improper use, abuse, tampering, improper installation, or failure to follow maintenance and operation procedures. Examples of the defects not covered by warranty include, but are not limited to: () Damage to the exterior or interior finish as a result of the above, () Use with utility service other than that designated on the rating plate, () Improper connection to utility service, () Inadequate or excessive water pressure, () Corrosion from chemicals dispensed in excess of recommended concentrations, (6) Failure of electrical components due to connection of chemical dispensing equipment installed by others, (7) Leaks or damage resulting from such leaks caused by the installer, including those at machine table connections or by connection of chemical dispensing equipment installed by others, () Failure to comply with local building codes, (9) Damage caused by labor dispute. Warranty of Parts: Champion/Moyer Diebel warrants all new machine parts produced or authorized by Champion/Moyer Diebel to be free from defects in material and workmanship for a period of 90 days from date of invoice. If any defect in material and workmanship is found to exist within the warranty period Champion/Moyer Diebel will replace the defective part without charge. DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY. CHAMPION/MOYER DIEBEL'S WARRANTY IS ONLY TO THE EXTENT REFLECTED ABOVE. CHAMPION/MOYER DIEBEL MAKES OTHER WARRANTIES, EXPRESS OR IMPLIED, ILUDING, BUT T LIMITED TO, ANY WARRANTY OF MERCHANTABILITY, OR FITNESS OF PURPOSE. CHAMPION/MOYER DIEBEL SHALL T BE LIABLE FOR IIDENTAL OR CONSEQUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE THE EXCLU- SIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN CHAMPION/MOYER DIEBEL DISHWASHING MACHINES AND CHAMPION/MOYER DIEBEL PARTS, AND ALL OTHER REMEDIES ARE EXCLUDED, ILUDING ANY LIABILITY FOR IIDENTALS OR CONSEQUENTIAL DAMAGES. Champion/Moyer Diebel does not authorize any other person, including persons who deal in Champion/Moyer Diebel dishwashing machines, to change this warranty or create any other obligation in connection with Champion/Moyer Diebel Dishwashing Machines. rev. 699
GENERAL GENERAL This manual covers the Moyer Diebel 0PLUS undercounter dishwashing machine. This machine is fully automatic and is equipped with a / H.P. pump motor. All models are available for mounting directly to the floor or on optional stands (see accessories listed on page ). Standard equipment includes: -Automatic tank fill -Upper and lower spray arms -Common utility connections -Two dish racks (peg and flat) -0 Volt control circuit -Exclusive vent design for -Convenient, easy to use controls venting of condensation -Door latch activated start switch -Stainless steel heavy-gauge construction -Pumped drain (to ft/m) (vertical) -Detergent and rinse aid pumps -Final rinse sentry feature (high temp models only) This series of dishwahers is available in he following models: Model Numbers 0-HT PLUS, 0-HTN PLUS, 0-LTPLUS The 0-HT PLUS model is a high temperature ( C/0 F rinse) sanitizing model with booster and the final rinse sentry feature. The 0-HTN PLUS model is a high temperature (customer supplied C/0 F rinse water) sanitizing model without booster. The 0-LT PLUS model is a low temperature (60 C/0 F rinse) sanitizing model. Options Kit 0 - Top and side panels (P/N 07076) Kit 0 - Top panel only (P/N 0707) Kit 06 - Left side panel only (P/N 0707) Kit 07 - Right side panel only (P/N 07076) Kit 0 - Extended reach pumped drain kit (P/N 070766) Kit - 0 C/70 F temperature rise booster (P/N 0707) (for 9 C/0 F supply water).
GENERAL Accessories 7RS - 7" rack stand (raises working height and adds rack storage) 7T - 7" cabinet (raises working height and adds storage) CST - Combination sink/table (scraping and sorting station) 0 - Dish Rack (Peg Rack) 07 - Silverware Rack (Flat Bottom Rack) Electrical Power Requirements Booster Machine Power Requirement Model Voltage Rise Full Load Amp (% Service Factor) 0-LT PLUS /60/ N/A 9 0-HTN PLUS /60/ N/A 9 0-HT PLUS 0/60/ 0 0-HT PLUS 0/60/ 0 7 7 0-HT PLUS 0/60/ 70 7 0-HT PLUS 0/60/ 70 6 TE: 0-0V/60Hz/PH electrical supply service must be a -wire plus ground for connection as shown. 0006 v -Wire Plus Ground Diagram v 0-0 L L N G
INSTALLATION INSTALLATION Unpacking! WARNING: Care should be taken when lifting the machine to prevent damage.. Immediately after unpacking your machine, inspect for any shipping damage. If damage is found, save the packing material and contact the carrier immediately.. Remove the dishwasher from the skid. Adjust the feet if required, then move the machine to its permanent location.. Level the machine (if required) by placing a level on the top of the machine and adjusting the feet. Level the machine front-to-back and side-to-side. CAUTION:! After locating your machine, the installation must meet local health codes. An example may be to seal your machine to the floor using a good grade of silicone sealant. Electrical Connections!! WARNING: Electrical and grounding connections must comply with the National Electrical Code and/or Local Electrical Codes. WARNING: When working on the dishwasher, disconnect the electric service and tag it to indicate work is being done on that circuit.. The electrician should compare the electrical specifications on the machine electrical rating label (located on the lower left front panel) to the electrical power supply before connecting the machine to the incoming service at a fused disconnect switch. TE: The 0-0V/60Hz/PH electrical supply service for this machine must be a -wire plus ground service.. On the 0V-0V models, a terminal block is provided on the left front side of the machine (located behind the front panel) for electrical service connections. A fused disconnect switch or circuit breaker (supplied by user) is required to protect each power supply circuit.. On V models, your machine is already equipped with a -foot power cord and plug suitable for V-A service.
INSTALLATION Plumbing Connections! CAUTION: Plumbing connections must comply with local sanitary and plumbing codes. Water Connections. Connect the hot water supply (60 C/ 0 F Min) to the /" I.D. fill hose provided. The fill solenoid valve is equipped with a flow control that will accept water pressures from 7 kpa/ psi to 66 kpa/9 psi.. Install a manual shut-off valve with /" garden hose connection in the water supply line close to the machine to accommodate installation and servicing the machine. The shut-off valve should be the same size or larger than the supply line.. The fill solenoid valve is equipped with a built-in strainer to protect from particles in the water supply. Drain Connections. All Models are supplied with a flexible /" I.D. drain hose, which must be connected to a -/" drain using a wye (Y) fitting close to the machine.. Drain connections height should be a maxium of feet from the from the floor. Detergent/Chemicals Use a qualified detergent/chemical supplier for your detergent, rinse aid, and chemical sanitizer needs.. Your machine has a liquid detergent dispensing pump. Insert the labeled detergent pickup tube into the detergent container. The pickup tube has a strainer on the end to prevent crystallized chemical from clogging the supply lines.. The cycle timer located in the main control cabinet is equipped with adjustable cams for the chemical dispensing pump(s). The cams control the length of time that the pumps operate. A qualified person may adjust the cam settings if necessary. Refer to the timer chart diagram(s) at the end of the manual for timer cam locations. Factory time settings are only approximate. Have your chemical supplier check the concentration and make the necessary adjustments. TE: A nonchlorinated detergent is recommended for your dishwasher. Rinse Aid. A rinse aid pump is included on all models. Insert the labeled Rinse Aid pickup tube into the rinse aid container. Contact your chemical supplier for adjustment to ensure proper dosage. Chemical Sanitizer. Model 0-LT PLUS is supplied with chemical sanitizer dispensing pump. Insert the labeled Chemical Sanitizer pickup tube into the chemical sanitizer container. Have your chemical supplier set chemical dosage according to local code.. Contact your chemical supplier for adjustment of the chemical sanitizer to ensure proper dosage. 6
INSTALLATION Completing Installation. Remove any foreign material from inside the machine.. Center the scrap screen over the sump opening.. Prime the booster using the following procedure (if applicable). CAUTION:! To prime the booster, the folowing procedure must be followed AFTER the electrical and plumbing connections have been made. a. Remove the front panel. b. Locate the Installation and Service toggle switch on the extreme left side of of the control box. c. Press the toggle switch to the Booster Fill position and hold it approximately minute (or until water enters wash tank). d. Release the toggle switch to stop the water flow. e. You have complete the booster priming process. TE: Push the Installation and Service toggle switch to the ON position. Electrical power is now supplied to the machine.! WARNING: Failure to prime the booster may cause damage to the booster elements and other electrical components and will void the warranty,. After plumbing and electrical connections are completed, check the machine for water leaks by depressing the ON/FILL/OFF/DRAIN to the ON/FILL position, then close and latch the door. This allows the tank to fill and complete the rinse cycle. Check for leaks.. Open the door and check the water level. The water level should be /" over the scrap screen.. Depress the ON/FILL/OFF/DRAIN switch to the OFF/DRAIN position, close and latch the door to drain the machine. This allows the machine to complete the 0-second wash and drain cycle. Check the drain plumbing for leaks or kinks in drain hose. 6. Replace the front panel. Installation is now complete. 7
OPERATION OPERATION Operation Summary The following is a summary of your Undercounter Dishwashing Machine operating cycle:. The cycle begins when you close and latch the door.. The green cycle lamp lights and the wash pump starts.. The pump runs during the wash cycle for approximately 0 seconds. The wash cycle duration is extended if the booster is not up to temperature.. The wash pump stops, and the drain valve is opened.. After a - second pause, the pump drain cycle begins and continues for approximately 0 seconds. Just before this cycle ends the fill valve will come on for - seconds to flush the wash tank of any remaining detergent. 6. After a - second pause, the fill valve opens, and the pump starts for the rinse cycle. 7. Within approximately seconds, the rinse cycle is complete. The pump stops, the green cycle lamp turns off, and the cycle is complete.. Open the door and remove the rack of clean ware. Daily Operation Procedures The operation of your dishwasher will be more efficient when these procedures are followed:. Check that the spray arm and scrap screen are in place.. Close and latch the door. Push the ON/FILL switch to the ON position. The tank will begin filling with water. This procedure is followed only when the tank is empty.. When the tank is full, check the wash tank temperature gauge. Minimum wash temperatures are: 0-HT PLUS, 0-HTN PLUS - 66 C/0 F. 0-LT PLUS - 60 C/0 F.! CAUTION: If the wash water temperature falls below the minimums listed above, you must run an empty cycle to refill with fresh hot water.. Scrap and preflush all items to be washed, and load the items into the rack. DO T OVERLOAD the rack. Wash only one layer of silverware in a rack.. Open the door and insert the rack into the machine. 6. Close and latch the door. This will start the wash cycle. The green cycle lamp located on the front control panel will light. This lamp will remain on until the entire wash and rinse cycles are completed.
OPERATION TE: The machine may be stopped at any time by opening the door. When restarted, the cycle does not start over. It will continue from the point at which it was interrupted. 7. Check the rinse temperature during the final rinse (0 seconds into cycle). The rinse temperature must be C/0 F minimum for models 0-HT PLUS, 0-HTN PLUS and 60 C/0 F for model 0-LT PLUS.. The pump will automatically stop and the green cycle light will turn off indicating the cycle is completed. 9. Open the door and remove the rack. 0. Repeat steps -9 for additional cycles. Machine operation is automatic.. CLEAN the scrap screen after every meal period. During heavy usage, the scrap screen should be cleaned more frequently. CAUTION:! Poor machine performance and/or damage to the machine can occur if the scrap screen becomes clogged with soil or waste particles.. To drain water out of the tank at the end of each day. Flip ON/FILL/OFF/DRAIN switch to DRAIN position. Close and latch door. Machine will drain completely in approximately 0 seconds.! CAUTION: DO T LEAVE WATER IN THE TANK OVERNIGHT. Water left in the tank overnight will allow harmful chemicals to deteriorate the tank. 9
MAINTENAE MAINTENAE The efficiency and life of your machine is increased by regularly scheduled preventive maintenance. A well maintained machine gives better results and service. An investment of a few minutes of daily maintenance will be worthwhile. The best maintenance you can provide is to keep your machine clean. Components that are not regularly cleaned and flushed will clog and become inoperative. Intervals shown in the following schedules represent an average length of time between necessary maintenance. Maintenance intervals should be shortened whenever your machine is faced with abnormal working conditions, hard water, or multiple shift operations. Cleaning Schedule Daily-Every Hours. Depress the ON/FILL/OFF/DRAIN switch to OFF/DRAIN position and close and latch the door to drain the tank.. Open the door and remove the upper and lower spray arms by unscrewing the knurled fastener.. Remove the scrap screen carefully to keep soil or waste particles from falling into the sump. Remove any material caught in pump intake.. Clean inside the tank with clean water. Backflush the scrap screen until it is clean. Do not strike the screen against solid objects.. Clean the wash arms to remove any debris from spray openings. Do not strike the spray arms against solid objects. 6. Reinstall the scrap screen and spray arms. 7. Leave the door open overnight to allow drying.. Report any unusual conditions to your supervisor. Meal Periods. Clean the scrap screen after every meal period and more frequently during heavy usage. Do not allow the scrap screen to become clogged with soil or waste particles. 0
MAINTENAE Maintenance Schedule As Required. Check the temperature gauge reading to make sure that it is accurate.. Check the chemical supplies and refill as necessary. Weekly. Inspect all water lines for leaks and tighten them at joints if required.. Clean all detergent residue from the exterior of the machine.. Check the drain for leaks.. Remove and closely inspect the spray arms for blockage.. Check for damage to the scrap screen. Ineffective screening can cause wash system failures, or poor washing results. 6. Clean the detergent, sanitizer, and rinse aid supply tubes. Complete the following procedure: a. Remove the detergent, sanitizer, and rinse aid pick-up tube(s) from the container(s). Place the tube(s) into a container of hot water. b. Ensure ON/FILL/OFF/DRAIN switch is in the ON position depress and hold the DET prime switch (located on the front panel) until clear water enters the tank through the fill air gap (located on the right side of the tank). c. Your machine is equipped with a sanitizer and/or rinse aid pump, follow the same procedure by pressing the SANITIZER and/or the RINSE AID prime switch until clear water enters the tank through the fill air gap. d. When completed, remove the pickup tubes from the hot water and reinsert them into the correct chemical containers. Repeat the priming procedures to ensure that chemicals have filled the tubes for the next operating period. e. Run a complete cycle to flush chemicals from the tank.
MAINTENAE Deliming Your dishwasher should be delimed regularly. The frequency will depend on the mineral content of your water. Inspect your machine interior for lime deposits. If deliming is required, a deliming agent should be used for best results.! DANGER: Deliming solution or other acids must not come in contact with household bleach (sodium hypochlorite) or any chemicals containing chlorine, iodine, bromine, or fluorine. Mixing will cause hazardous gases to form. Skin contact with deliming solutions can cause severe irritation and possible chemical burns. Consult your chemical supplier for specific safety precautions. If you have the chemical sanitizing model (0-LT PLUS), carefully follow the following procedure before deliming:. Remove the sanitizer tube from the container. Place the tube into a container of hot water.. Depress and hold the SANITIZER prime switch (located on the front panel) until all sanitizer has been purged from the hoses.. Close the door and depress the door latch. Complete two operating cycles to purge the machine of all sanitizer. Deliming Procedure Complete the following procedure to delime your machine:. Add the delime chemical to wash the tank (per chemical supplier specifications).. Close and latch the door.. The dishwasher will complete a regular cycle.. Check the deliming results and repeat if necessary per the chemical supplier s specifications.. Operate the dishwasher for at least four complete cycles to purge the machine of any deliming chemicals. 6. Drain the dishwasher. Deliming is complete.
TROUBLESHOOTING TROUBLESHOOTING Before determining any specific cause of a breakdown or abnormal operation of your dishwasher, check that:. Power supply is turned on. All switches are ON.. Wash arms are clean.. Scrap screen is properly positioned and clean.. Thermostat is at the correct setting.. Sanitizer, detergent, and rinse additive dispensers are adequately filled. 6. All plumbing valves are open and drain hose is not kinked. If a problem still exists, use the following table for troubleshooting. CONDITION CAUSE SOLUTION Machine will not start Door not closed and latched........ Make sure door is fully latched Main switch off, or unit unplugged.. Check disconnect or plug into outlet Low or no water Main water supply is turned off.... Turn on house water supply Water level setting low............ Adjust water level Chemical not feeding No chemical in container.......... Replace or fill container Feed tubes to/from chemical....... Clear obstruction and flush pump clogged with hot water Screen on feed tube clogged........ Clean and replace Tubing kinked or split............ Straighten or replace tubing Water temperature Incoming water temperature........ Raise house supply temperature to is low when in use at machine too low 60 C/0 F for all machines Insufficient pumped spray Clogged spray arms.............. Clean pressure Scrap screen full................. Must be kept clean and in place Low final rinse temperature Low incoming water.............. Check the booster - be sure the temperature thermostat is set to maintain 66 C/0 F temperature (0-L PLUS is 60 C/0 F) (Check all valves to be sure they are clean and operating) Poor washing results Detergent dispenser not........... Contact service agent operating properly Insufficient detergents............ Check dosage Check and fill Contact detergent supplier Detergent setting too low......... Contact detergent supplier Wash water temperature too low.... See above booster temperatures, run cycle Wash arms clogged.............. Clean wash arms Improperly scraped dishes......... Check scraping procedures Ware being improperly............ Use proper racks - do not overload placed in rack racks Improperly cleaned.............. Unclog wash arms to maintain equipment proper pressure and flow conditions No water in wash well Opening door prior............... Close and latch door. Wait for green light to cycle completion to go out before opening door. Water supply is turned off......... Turn on supply No water in wash tank Door not latched................. Latch door after activating the Wait for wash tank to fill ON/FILL switch Cycle time increases Incoming water temperature........ Raise temperature to 60 C/0 F for all with each cycle is too low machines.
THIS PAGE INTENTIONALLY LEFT BLANK
REPLACEMENT PARTS REPLACEMENT PARTS
REPLACEMENT PARTS 0000 0 7 9 6 Figure Track and Panel Assembly 6
REPLACEMENT PARTS TRACK AND PANEL ASSEMBLY Fig. Part Description Qty Item No. No. 007 Screw, 0- x -/" Lg. Truss Head... 0097 Front Panel... 00 Screw, 0- x /" Lg. Round Head... 00 Screw, 0- x /" Lg. Round Head... 006 Track, RH... 6 006 Track, LH... 7 07067 Cover, Vent... 0076 Panel, LH Side... 9 007 Panel, Rear (HT PLUS)... 9 0097 Panel, Rear (LT PLUS, HTN PLUS)... 0 0077 Panel, RH Side... 007 Panel, Top... 00 Screw, 0- x /" Lg. Truss Head... 0 7
REPLACEMENT PARTS 0000 6 7 0 9 6 7 Figure Door and Switch Assembly
REPLACEMENT PARTS DOOR AND SWITCH ASSEMBLY Fig. Part Description Qty Item No. No. 00 Screw, 0- x /" Truss Head... 6 0096 Plate, Door Latch... 0097 Handle, Door Latch... 007 Retaining Ring, Plunger... 07096 Assembly, Door Catch (Includes items, 6)... 6 0096 Plunger, Door Catch... 7 00 Gasket, Steam... 0 Screw, Round Head (6- x /")... 9 0709 Plate, Door Switch... 0 090 Switch, Door Magnetic Reed... 00 Gasket, Upper Door... 00 Gasket, Side Door... 009 Nut, Plain /-0... 007 Spring, Door Hinge... 00 Bolt, /-0 x -/" Hex Head... 6 0706 Arm, Door Hinge... 7 000 Washer, Lock /" Split... 0707 Door... - 00 Wiring, Harness, Door Switch... - 0706 Door Assy. (includes items -6, ) 9
REPLACEMENT PARTS 0007A TO RINSE 9 0 9 6 THERMOMETER (CALLED OUT IN CONTROL BOX) 7 6 6 TO PUMP DRAIN TO DRAIN Figure Tank/Drain Assembly 0
REPLACEMENT PARTS TANK/DRAIN ASSEMBLY Fig. Part Description Qty Item No. No. 006 Scrap Screen... 009 Locknut, / NPT Nickel-Plated... 006 O-Ring, Thermometer... 007 Adapter, Thermometer... 0076 Hose, /" ID x 7/" OD PVC Braided ( ft.)... 6 000 Clamp, hose... 7 0090 Hose /" ID x " OD Braided PVC... 0066 Valve, Drain... 9 007 Adapter, Pump Tube... 0 0 O-ring... 0079 Nut, Jam "-... 006 Tube, Pump Outlet... 06 Thermostar, High Limit... 09 Nut, Grip 6- w/nylon Insert...
REPLACEMENT PARTS 0000 6 7 9 0 TANK BOTTOM Figure Pump Assembly
REPLACEMENT PARTS PUMP ASSEMBLY Fig. Part Description Qty Item No. No. 00 Spindle, Lower Wash Arm... 00 Screw, - x -/" Round Head... 00 Screw, - x /" Round Head... 0079 Housing, Top... 007 Diffuser... 6 0070 Impeller... 7 0076 Adapter Plate, Suction... 007 Plate, Drain lnlet... 9 0070 O-ring... 0 007 Propeller/Rotating Seal Assembly... 007 Mounting Plate/Seal Assembly (Includes Item 0)... 00 Gasket, Pump... 0066 Screw, 0- x /" Hex Washer Head... 0070 Washer, Sealing Teflon... *- 07007 Pump/Motor Assembly (60 Hz) (V)... - 07966 Nut, Grip 0-, SST (Not Shown) (For mounting Item )... * Motor not available as a separate repair part
REPLACEMENT PARTS 000A TOP OF HOOD 6 7 9 0 0 PUMP TANK BOTTOM FROM PUMP Figure Wash System Assembly
REPLACEMENT PARTS WASH SYSTEM ASSEMBLY Fig. Part Description Qty Item No. No. 009 Hose, Upper Wash... 006 Clamp, Hose "... 07060 Spindle, Upper Wash Arm... 00 O-ring, -/" x -/"... 00 Screw 0- x / Truss Head... 6 00 Bushing, Upper Wash Arm... 7 0709 Wash Arm, Upper... 000 Pivot, Upper Wash Arm... 9 007 Retainer, Upper Pivot... 0 006 Screw, # x / Truss Head... 006 Nut, Spray Arm Lock... 07009 Wash Arm, Lower... 000 Bushing, Lower Wash Arm...
REPLACEMENT PARTS 6 9 0 7 6 THERMOSTAT (CALLED OUT IN CONTROL BOX) 6 FROM FILL VALVE Figure 6 Booster Assembly and Water Inlet Piping (HT PLUS Only) 6
REPLACEMENT PARTS BOOSTER ASSEMBLY AND WATER INLET PIPING (HT PLUS ONLY) Fig. 6 Part Description Qty. Item No. No. 00679 Clamp, hose... 009 Hose, /" I.D... ft. 006 Elbow, / MPT X/ Hose x 90... 000 Bushing, reducing / NPT x / NPT Brass... 009 Bolt., /-0 x /" Hex Head... 6 000 Washer, Lock /" Split... 7 09 Nut, Grip 6- w/nylon Insert... 06 Thermostat, high limit... 9 0090 Tank, booster (tank only)... 0 077 Hose /" I.D. (")... A/R 007 Plug, pipe /"... 099 O ring, gasket... Heater element, 6KW (0 rise) 0/0V PH... Heater element, 9KW (70 rise) 0/0V PH... 009 Nut, plain /-0... 6 0790 Cover, heater element... --- 0997 Wire, Jumper Heater Element (Not Shown)... --- 0076 Insulation, Heater Terminal (Not Shown)... --- 0097 Label, Cover Warning (Not Shown)... 7
REPLACEMENT PARTS 9 7 6 TO FILL 0 0009 WATER CONNECTION Figure 7 Water Inlet Piping (HTN PLUS, LT PLUS Only)
REPLACEMENT PARTS WATER INLET PIPING (HTN PLUS, LT PLUS ONLY) Fig. 7 Part Description Qty Item No. No. 007 Foot, adjustable... 00679 Clamp, hose... 077 Hose, /" ID (LT PLUS Only)... ft. 077 Hose, /" I.D (HTN PLUS Only)... ft. 006 Elbow, / MPT x /" Hose x 90 Brass... 6 009 Valve, solenoid (/NPT)... 7 00 Repair kit, /" valve... 00 Coil, V /" valve... 9 009 Flow washer, /" valve... 0 000 Washer, lock /" split... 009 Bolt, /-0 x/" Hex Hd... 0000 Clamp, valve support... 006 Coupling, / MPT x /" hose barb... 000 Washer, hose... 9
REPLACEMENT PARTS 0009 (See Corresponding Pump For Hose) From Detergent Pump From Sanitizer Rinse-aid Pumps 6 7 RH Side of Tank From Top of Booster or From Fill Valve Figure Fill System 0
REPLACEMENT PARTS FILL SYSTEM Fig. Part Description Qty Item No. No. 077 Hose, /" I.D. (HTN PLUS, LT PLUS)... A/R 00 Tie Wrap, Hose... 06090 Bracket, Tie Wrap... 07966 Nut, Grip, 0- w/nylon Insert... 0090 Gasket, Inlet Chute... 6 0067 Inlet Chute... 7 009 Tie, Nylon "... 077 Hose, Fill /" I.D.... ft.
REPLACEMENT PARTS Rinse Aid 000 6 7 Detergent 6 7 TO FILL SYSTEM 6 9 0 9 TO FILL ASSY 0 6 7 6 TO CHEMICAL SUPPLY 9 0 TO DETERGENT SUPPLY Figure 9 Detergent/Rinse Aid Pump Assemblies (HT PLUS, HTN PLUS)
REPLACEMENT PARTS DETERGENT/RINSE AID PUMP ASSEMBIES (HT PLUS, HTN PLUS) Fig. 9 Part Description Qty Item No. No. 0077 Motor, Pump (Detergent)... 0076 Motor, Pump Injector (Rinse Aid)... 0060 Bracket, Detergent/Sanitizer Pumps (Rinse Aid)... N/A Screw, M x mm Hex Head... 00 Screw, 0- x /" Lg. Truss Head... N/A Housing, Pump... 6 0097 Washer, Lock # Split... 7 00 Screw,- x /" Lg. Pan Head... 00 Screw, - x /" Round Head... 9 N/A Screw, Set M6 x mm... 0 N/A Rotor Assembly... 09 Hose, Pump... N/A Cover, Pump Housing... N/A Washer, Flat M... N/A Nut, Wing M... 009 Tie Wrap, Hose... 6 00667 Hose, Detergent, /" I.D. PVC (Clear)... A/R 7 006 Elbow, /" O.D. x 90 Barbed... 0069 Label, Detergent... 9 0066 Tube, Pick-Up... 0 0069 Strainer, Pick-Up Tube... 009 Tie Wrap, Hose... 0707 Rotor Assembly... 07066 Element Tube Assy (CC/Min)... 0069 Screw, 6- x 7/ Pan Head... 00666 Hose, /" ID PVC (Clear)... A/R 6 00 Label, Rinse Aid... - 099 Detergent Pump Head Assy. (includes items, 6, 0-) - 07096 Detergent Pump/Motor Assy. (includes items,, 6-0) - 0707 Rinse Aid Pump Assy (includes items, 6, 7, 9-6)
REPLACEMENT PARTS 0000 6 7 0 9 DETERGENT PUMP (SEE FIG. 9) TO FILL SYSTEM 0 TO CHEMICAL SUPPLY Figure 0 Detergent/Sanitizer/Rinse-Aid Pump Assembly (LT PLUS Only)
REPLACEMENT PARTS DETERGENT/SANITIZER/RINSE-AID PUMP ASSEMBLIES LT PLUS ONLY Fig. 0 Part Description Qty Item No. No. 0076 Motor, Pump... 0060 Bracket, Detergent/Rinse Pump... 00697 Bracket, Sanitizer Pump... 00 Screw, 0- x /" Lg. Truss Head... 0097 Washer, Lock # Split... 6 00 Screw, - x /" Lg. Pan Head... 7 0707 Rotor Assy... 07066 Element Tube Assy (cc/min)... 9 0069 Screw, 6- x 7/" Lg. Pan Head... 0 00666 Hose, /" I.D. PVC (Clear)... A/R 0069 Label, Sanitizer... 00 Label, Rinse-Aid... 0066 Tube, Pick-Up... 0069 Strainer, Pick-up Tube... 009 Tie Wrap, Hose... - 07096 Detergent Pump Assy.... (lncludes Detergent Pump and Items, -9) - 0707 Rinse-Aid Pump Assy (Includes Items,, -0, -)
UP L S REPLACEMENT PARTS L L T T 6 7 0 9 FILL 6 OFF ON 7 0 9 000A Figure Control Panel Assembly 6
REPLACEMENT PARTS CONTROL PANEL ASSEMBLY Fig. Part Description Qty. Item No. No. * 070 Timer assy (HT PLUS Only) (Includes items -)... * 070 Timer assy (HTN PLUS Only) (Includes items -)... * 07090 Timer assy (LT PLUS Only) (Includes Items -)... 0096 Motor, timer... 0079 Switch, timer... A/R 006 Bracket, timer support (HTN PLUS)... 006 Bracket, timer support (HT PLUS, LT PLUS)... 0070 Bearing, timer... 6 70 Contactor, pole 0A, 0V (0 HT PLUS only) (Booster)... 7 00 Relay, motor start (V, 0Hz)... 009 Relay, door safety switch (A, 0VAC coil)... 9 000 Screw (0- x / Rd Hd)... 0 009 Washer, lock (#0 ext. tooth)... 007709 Washer, flat (#0 ss)... 00 Nut, plain (0- Brass)... 0079 Board, terminal... 000 Bracket, thermostat (0 HT PLUS only)... 09069 Thermostat, booster (0 HT PLUS only)... 6 6 Thermometer, ft. Gas Filled... 7 00 Lamp, green... 006 Switch, rocker (DPDT)... 9 0069 Switch, rocker (Spring return)... 0 0096 Label, switch, overlay... 0 00966 French label, switch overlay... 00 Screw (0- x /" Truss Hd)... 00979 Panel (sheet metal only)... 009 Block, terminal (HT PLUS)... 007 Switch, position toggle... 069 Relay PDT 0A 0V... 00 Harness, Control Box (HT PLUS) (Not Shown)... 00960 Harness, Conrtol Box (HTN PLUS) (Not Shown)... 0096 Harness, Control Box (LT PLUS) (Not Shown)... 7
THIS PAGE INTENTIONALLY LEFT BLANK
ELECTRICAL SCHEMATICS ELECTRICAL SCHEMATICS 9
ELECTRICAL SCHEMATICS SERVICE SWITCH FILL OFF TO CUSTOMER DISCONNECT SWITCH V NEUTRAL 0V GND CT CTC CUSTOMER TO SUPPLY RATED VOLTAGE/PHASE/Hz, AS SPECIFIED PER ORDER, TO DISCONNECT SWITCH. ALL POWER SUPPLIED TO EACH CONNECTION POINT MUST COMPLY WITH ALL LOCAL ELECTRICAL CODES. MSW ON OFF CAM ON CR PSDR 6 7 6 7 CAM CAM BOOSTER TANK WTS 0 9 9 BHTR WTS 0 HLTS SRC HLTS 9 CAM F V (IF USED) 0 DP WHTR WASH/ /RINSE BLU CAM DRAIN RED WHT GND CR BLK GRN CAM 9 START CW START CCW GND MAIN TP TM CLT CAM 0 D V 6 6 CAM 7 DM 7 7 CAM 6 (IF USED) RM DSS 0 ICR BHTR BOOSTER HEATER CLT CYCLE ON LIGHT MSW MAIN SWITCH ON/FILL OFF/DRAIN WTS WATER THERMOSTAT BLK BLACK CT CONTACTOR PSDR PRIME SWITCH DETERGENT, RINSE BLU BLUE CTC CONTACTOR COIL CR RELAY CAM HOMING DM DETERGENT MOTOR CR RINSE SENTINEL RELAY CAM PUMP MOTOR DP DRAIN PUMP (IF USED) DSS DOOR SAFETY SWITCH CAM PUMP MOTOR REVERSING DS DOOR SWITCH RM RINSE MOTOR (IF USED) CAM CAM CAM 6 CAM 7 CAM CAM 9 TOLERAE DECIMAL ANGLE SCALE DRAIN FILL RINSE DETERGENT CYCLE RINSE SENTINEL : FORMING:DIMENSIONS ARE FROM BRAKELINE TO BRAKELINE UNLESS OTHERWISE TED A B C D E DV EC/D FV GND GRN HTLS DRAIN VALVE EXTENDED CYCLE/DELIME FILL VALVE GROUND GREEN HIGH LIMIT THERMOSTAT HOLE DIMENSIONS F G H J SRC SS TM TP WHT WHTR CURRENT OPERATED START RELAY COIL SERVICE SWITCH TIMER MOTOR THERMAL PROTECTOR WHITE WATER HEATER ISSUED DR. CH. RTG. A REV ECN SCHEMATIC 0+ SERIES HIGH TEMP RELEASED TO PRODUCTION DESCRIPTION SKH BY CH DRAWING. JUL -0 DATE 006 Figure Electrical Diagram, 0-HT PLUS 0
ELECTRICAL SCHEMATICS TO CUSTOMER RECEPTACLE V 60Hz CUSTOMER TO SUPPLY RATED VOLTAGE/PHASE/Hz, AS SPECIFIED PER ORDER, TO DISCONNECT SWITCH. ALL POWER SUPPLIED TO EACH CONNECTION POINT MUST COMPLY WITH ALL LOCAL ELECTRICAL CODES. BLK WHT GND MSW ON CLT OFF CAM CR 6 7 CAM CAM 9 9 L SRC S M TM CAM WASH/ /RINSE DRAIN BLU RED BLK START CW START CCW MAIN CAM 9 0 F V (IF USED) DP WHT GRN TP CAM 0 D V GND GND PSDR 6 6 CAM 7 DM 7 7 CAM 6 (IF USED) RM DSS 0 CR BLK BLACK CLT CYCLE ON LIGHT PSS PRIME SWITCH SANITIZER BLU BLUE DM DETERGENT MOTOR ICR RELAY CAM HOMING DP DRAIN PUMP (IF USED) DSS REED SWITCH CAM PUMP MOTOR RL RELAY RM RINSE MOTOR (IF USED) CAM PUMP MOTOR REVERSING DV DRAIN VALVE SRC CURRENT OPERATED START RELAY COIL CAM DRAIN FV FILL VALVE SM SANITIZER MOTOR CAM FILL CAM 6 RINSE CAM 7 DETERGENT CAM CYCLE TOLERAE DECIMAL ANGLE SCALE : FORMING:DIMENSIONS ARE FROM BRAKELINE TO BRAKELINE UNLESS OTHERWISE TED A B C D E GND GRN HTLS MSW PSDR HOLE DIMENSIONS F GROUND GREEN HIGH LIMIT THERMOSTAT MAIN SWITCH ON/FILL OFF/DRAIN PRIME SWITCH DETERGENT, RINSE G H J ISSUED DR. CH. RTG. TM TP WHT WHTR WTS TIMER MOTOR THERMAL PROTECTOR WHITE WATER HEATER WATER THERMOSTAT A REV ECN SCHEMATIC 0+ SERIES HTN RELEASED TO PRODUCTION DESCRIPTION SKH BY CH AUG 0/0 DATE DRAWING. 006 Figure Electrical Diagram, 0-HTN PLUS
ELECTRICAL SCHEMATICS TO CUSTOMER RECEPTACLE V 60Hz CUSTOMER TO SUPPLY RATED VOLTAGE/PHASE/Hz, AS SPECIFIED PER ORDER, TO DISCONNECT SWITCH. ALL POWER SUPPLIED TO EACH CONNECTION POINT MUST COMPLY WITH ALL LOCAL ELECTRICAL CODES. BLK WHT GND MSW ON CLT OFF CAM 9 CR 6 CAM 7 CAM 9 9 L SRC S M TM CAM WASH/ /RINSE DRAIN BLU RED BLK START CW START CCW MAIN CAM 9 0 F V (IF USED) DP WHT GRN TP CAM 0 D V GND GND PSDR 6 6 CAM DM PSS 7 7 CAM 6 CAM 7 (IF USED) RM SM DSS 0 CR BLK BLACK CLT CYCLE ON LIGHT PSS PRIME SWITCH SANITIZER BLU BLUE DM DETERGENT MOTOR ICR RELAY CAM HOMING DP DRAIN PUMP (IF USED) DSS REED SWITCH CAM PUMP MOTOR RL RELAY RM RINSE MOTOR (IF USED) CAM PUMP MOTOR REVERSING DV DRAIN VALVE SRC CURRENT OPERATED START RELAY COIL CAM DRAIN FV FILL VALVE SM SANITIZER MOTOR CAM FILL CAM 6 RINSE CAM 7 SANITIZER CAM DETERGENT CAM 9 CYCLE TOLERAE DECIMAL ANGLE SCALE : FORMING:DIMENSIONS ARE FROM BRAKELINE TO BRAKELINE UNLESS OTHERWISE TED A B C D E GND GRN HTLS MSW PSDR HOLE DIMENSIONS F GROUND GREEN HIGH LIMIT THERMOSTAT MAIN SWITCH ON/FILL OFF/DRAIN PRIME SWITCH DETERGENT, RINSE G H J ISSUED DR. CH. RTG. TM TP WHT WHTR WTS TIMER MOTOR THERMAL PROTECTOR WHITE WATER HEATER WATER THERMOSTAT A REV ECN SCHEMATIC 0+ SERIES LOW TEMP RELEASED TO PRODUCTION DESCRIPTION SKH BY CH DRAWING. AUG 0-0 DATE 006 Figure Electrical Diagram, 0-LT PLUS
TIMING CHARTS TIMING CHART 0-HTM 000M CAM 6 7 9 TIME IN SECS 0 0 0 0 0 0 60 70 0 90 00 0 0 0 0 HOMING CAM WASH PUMP FORWARD=WASH WASH PUMP REVERSE=DRAIN WASH PUMP REVERSING CAM DRAIN VALVE DRAIN PUMP OPTIONAL FILL VALVE RINSE OPTIONAL PUMP DETERGENT PUMP AUTO-FILL DRAIN RINSE SENTRY 0 If booster thermostat is calling for heat, cam 9 will pause wash cycle until it reaches C/0 F. N C N O COM. SYHRON TIMER SWITCH DETAIL 9 7 6 LOCKING SCREW TIMER MOTOR TIMER ASSEMBLY 0-HTM Figure Timer Chart and Diagram, 0-HT PLUS, 0- HTN PLUS
TIMING CHARTS TIMING CHART 0-LTM 000M CAM TIME IN SECS 0 0 0 0 0 0 60 70 0 90 00 0 0 0 0 0 HOMING CAM WASH PUMP FORWARD=WASH WASH PUMP REVERSE=DRAIN WASH PUMP REVERSING CAM DRAIN VALVE DRAIN PUMP FILL VALVE 6 7 RINSE PUMP SANITIZER PUMP 9 DETERGENT PUMP AUTO-FILL DRAIN N C N O COM. SYHRON TIMER SWITCH DETAIL 9 7 6 LOCKING SCREW TIMER MOTOR TIMER ASSEMBLY 0-LTM Figure 6 Timer Chart and Diagram, 0-LT PLUS