Product Catalogue 2017
Table of Contents Air Cooled Units...... 3 ANK..... 2-4 tons... 4 ANL... 6.5-8 tons... 4 NLC... 15-90 tons... 5 NRK. 9-40 tons... 5 NRL 280-750... 14-50 tons... 6 NRL 800-1800..... 54-131 tons... 6 NRL 2000-3600... 145-261 tons........ 6 NRL FC 280-750...... 13-46 tons... 7 NRL FC 800-1800... 50-118 tons... 7 NRL FC 2000-3600... 126-236 tons...... 7 NRP 280-750...... 12-45 tons.. 8 NRP 800-1800... 52-120 tons... 8 NRP 2000-3600. 130-240 tons.... 8 NYB. 29 tons.... 9 Water Cooled Units.... 10 WRL / H.. 15-27 tons. 11 WWM... 31 tons.. 11 NXP..... 31-129 tons... 12 NXW...... 32-139 tons... 12 Fancoils.... 13 FCX US... 0.28-2 tons.. 14 FCX USP / USPO. 0.28-2 tons. 14 FCX I US. 0.43-2 tons.. 15 FCX I USP... 0.43-2 tons.. 15 FCW 0.54-1 ton.. 15 FCL / FCL I. 1-3 tons. 16 VED / VEDi. 2-5 tons. 16 MZC Multizone. 16 VentilCassaforma.... 17 Air to Air Units..... 18 CMP. 0.67 tons.. 19 2 aermec.us
Air Cooled Units 3 aermec.us
Air Cooled Units ANK Heat Pump Single Phase Cooling 2 4 Tons Heating 37,670 57,597 Btu/h ANK units are heat pumps for outdoors that have been designed and manufactured to satisfy heating, cooling, and the production of domestic hot water (DHW) in medium to small commercial or residential buildings. These units have extremely silent operation and are highly efficient. This can be attributed to the use of exchangers with a large exchange surface and low noise high-efficiency scroll compressors. Residential heating, cooling, radiant, domestic hot water Commercial process cooling for breweries, wineries, plastic extrusion etc. ANL Heat Pump or Chiller Cooling 6.5 8 Tons Heating 94,755 111,850 Btu/h ANL units are chillers and heat pumps for outdoor installation. The ANL has been designed and manufactured to satisfy heating, cooling, and the production of domestic hot water (DHW) in medium to small commercial or residential buildings. These units have extremely silent operation and are highly efficient. This can be attributed to the use of exchangers with a large exchange surface and low noise high-efficiency scroll compressors. 4 aermec.us
Air Cooled Units NLC Heat Pump or Chiller Cooling 15 90 Tons Heating 193,200 1,190,400 Btu/h The NLC units are air to water chillers and reversible heat pumps, for indoor installation. They are designed and manufactured for the production of chilled and heated water in residential and commercial buildings. The units are equipped with high efficiency scroll compressors, plug-fans, copper coils with aluminum fins, and plate heat exchangers on the system side. With the optional desuperheater or total heat recovery version, there is the possibility of producing hot water for free. Up to 2 of static. NRK Heat Pump Cooling 9 41 Tons Heating 116,880 593,280 Btu/h The NRK units are reversible heat pumps optimized for heating. They are designed and manufactured for the production of chilled and heated water in residential and commercial buildings. The units are equipped with high efficiency scroll compressors, axial fans, external copper coils with aluminum louvers, and plate heat exchangers on the system side. Units with a desuperheater (partial heat recovery) in cooling mode could produce hot water for free. Operation down to -4 F ambient. Hot water production up to 149 F. This unit has very high COP levels. 5 aermec.us
Air Cooled Units NRL 280-750 Heat Pump or Chiller NRL 800-1800 Heat Pump or Chiller Cooling 14 50 Tons Heating 165,967 600,571 Btu/h NRL chillers and heat pumps are equipped with series and made for outdoor installations. NRL units have been designed and manufactured to satisfy heating, cooling, or the production of domestic hot water (DHW) in medium to small commercial or residential buildings. With the optional de-superheater or total heat recovery version, there is the possibility of producing hot water for free. Cooling 54 131 Tons Heating 666,703 1,703,940 Btu/h NRL 2000-3600 Heat Pump or Chiller Cooling 145 261 Tons Heating 1,771,379 3,401,018 Btu/h 6 aermec.us
Air Cooled Units NRL FC 280-750 Freecooling Chiller NRL FC 800-1800 Freecooling Chiller Cooling 13 46 Tons The NRL free cooling chillers contain integrated water coils, automated 3 way valves, solenoid valves and custom software which allows the unit to provide maximum energy savings while offering a small footprint. These units operate in 3 modes, cooling only, hybrid free cooling and total free cooling. The hybrid free cooling (mechanical cooling with FC) mode operates when the ambient air is 3 F below the return water temperature. Operating in Hybrid mode with condenser fans at high speed and condensers modulating allows Aermec to provide the most efficient free cooling chillers on the market. Cooling 50 118 Tons NRL FC 2000-3600 Freecooling Chiller Cooling 126 236 Tons 7 aermec.us
Air Cooled Units NRP 280-750 Simultaneous Heating and Cooling NRP 800-1800 Simultaneous Heating and Cooling NRP 2000-3600 Simultaneous Heating and Cooling Cooling 12 45 Tons Heating 184,010 660,103 Btu/h Cooling 52 120 Tons Heating 738,278 1,689,276 Btu/h Cooling 130 240 Tons Heating 1,856,738 3,378,552 Btu/h NRP is the range of multipurpose external units operating on, designed for 2 pipe chilled / hot water change over + DHW production or a 4 pipe orientation for chilled or hot water at any point. With just one unit, simultaneous, independent requests for hot and chilled water are accommodated year round, generating energy savings. A difference from traditional cycle reverse heat pumps is that the heated water is produced in a different heat exchanger from the one used to produce cold water. This separates the two hot-cold sections that are required for four pipe systems. The cold side is dedicated to cold production and the hot side is dedicated to hot production. If the utility requires simultaneous hot and cold water the unit acts as a waterto-water heat pump. This controls condensation and evaporation across the two distinct plate heat exchangers associated to circulation of cold and hot water in the system. The system is capable of modulating the percentage of water-to-water recovery and air-to-water heat transfer, providing a 0 to 100 percent range of recovery. The multicircuit unit provides maximum efficiency both with full load and partial loads, guaranteeing operating continuity should one of the circuits stop to facilitate maintenance. 8 aermec.us
Air Cooled Units NYB Chiller or Freecooling Chiller Cooling 29 Tons (per module) With the NYB it is possible to couple up to 9 chillers to keep overall unit dimensions to a minimum. This modularity adapts the installation and operation to actual system development requirements. This way, the cooling capacity can be increased over time in a simple and economic manner. Optional desuperheater, for heat recovery of up to 40% of mechanical cooling. Each module can be removed without shutting the system off. 9 aermec.us
Water Cooled Units 10 aermec.us
Water Cooled Units WRL / H Heat Pump or Chiller WRL is a water cooled chiller and reversible heat pump operating with refrigerant. They are indoor units with hermetic scroll compressors. The unit has been designed to optimize heat pump operation which provides high performance and low energy consumption. The electric and hydronic connections are all located on the upper part of the unit facilitating installation in the smallest space possible. Cooling 15 27 Tons Heating 198,651 319,540 Btu/h WRL units are distinguished for their silence in operation. Careful soundproofing of the unit with suitable sound-absorbent material results in low sound levels. Using the electronic controller with an external air temperature sensor (accessory), the heat pump unit can vary the leaving water temperature based on outdoor ambient, thus increasing the energy efficiency. WWM Chiller Aermec s first stackable modular unit is here. Up to 32 connectable units with two 15 HP circuits. The modules can be linked together side by side, back to back, and stacked to reach a capacity of 960 tons. No clearance is required on the top, sides or back. A unit or (units) may be removed for maintenance without shutting the down. A real advantage is the high efficiency and small footprint as our modular system can save up to 60% of the floor space over the competition. Cooling 31 Tons (per module) 11 aermec.us
Water Cooled Units NXP Simultaneous Heating and Cooling Cooling 31 129 Tons Heating 402,916 1,684,093 Btu/h NRP is the range of multipurpose external units operating on, designed for 2 pipe chilled / hot water change over + DHW production or a 4 pipe orientation for chilled or hot water at any point. The unit has three heat exchangers: one for cold water, one for hot water and one for the ground loop. The three circuits are completely independent, guaranteeing that you can glycol the source and not the building. NXW Heat Pump or Chiller Cooling 31 129 Tons Heating 402,916 1,684,093 Btu/h NXW is the range of water cooled chillers and reversible heat pumps with refrigerant. The units are extremely efficient due to the use of high efficiency scroll compressor, and brazed plate heat exchangers with a large exchange surface. Sound absorbing panels cover all the components, ensuring very low sound levels, while still providing easy access to all the components. The multi-circuit unit provides maximum efficiency both with full load and partial loads. This guarantees operating continuity if one of the circuits stop to facilitate maintenance. With the optional desuperheater or total heat recovery version, there is the possibility of producing hot water for free. 12 aermec.us
Fancoils 13 aermec.us
Fancoils FCX US Fancoil Cooling 0.28 2.45 Tons Heating 8,503 58,126 Btu/h FCX US units are a universal cabinet fancoil that consists of a fan unit, a heat exchange element, and a filter. They are ideal for summer air conditioning and winter heating. Fed with cooled water coming from a chiller, they make the air of the room fresh, dry, and clean in a very short time and with great energy efficiency. The unit is fed with hot water coming from a heat pump or from a common boiler which results in economical heating during the winter season. Very well designed, quiet, and only has a depth of 8.5 inches. FCX USP / USPO Fancoil Cooling 0.28 2.45 Tons Heating 8,503 58,126 Btu/h FCX USP / USPO units are a ducted fancoil that consists of a fan unit, a heat exchange element, and a filter. They are ideal for summer air conditioning and winter heating. Fed with cooled water coming from a chiller, they make the air of the room fresh, dry, and clean in a very short time and with great energy efficiency. The unit is fed with hot water coming from a heat pump or from a common boiler which results in economical heating during the winter season. Very well designed, quiet, and only has a depth of 8.5 inches. 14 aermec.us
Fancoils FCX I US Fancoil Cooling 0.43 2.11 Tons Heating 116,000 51,658 Btu/h FCX I US units are universal cabinet fancoils that have continuous 0-100% variation of air flow rate. Thanks to the inverter technology combined with the latest brushless DC electric motor and the extremely high energy efficiency levels, the FCXi fan coils can modulate the airflow rate continuously from 0-100%. This means the capacity is adjusted moment by moment to the specific needs of the air conditioned room. This results in 50% energy savings during winter and summer air conditioning ventilation, compared with the traditional on-off ranges. FCX I USP Fancoil FCX I USP units are ducted fancoils that are extremely quiet. They have inverter technology with brushless DC electric motors with extremely high efficiency levels resulting in 50% energy reduction versus standard 3 speed fan motors. Cooling 0.43 2.11 Tons Heating 116,000 51,658 Btu/h FCW Fancoil Cooling 0.54 1.08 Tons Heating 8,194 16,217 Btu/h The FCW highwall fancoil unit is ideal for summer air conditioning and winter heating of any room. Fed with cooled water coming from a chiller, they make the air of the room fresh, dry, and clean in a short period of time and with great energy efficiency. The units are fed with hot water coming from a heat pump or from a common boiler and supply dry heating during the winter season. 15 aermec.us
Fancoils FCL / FCL I Fancoil Cooling 1.70 3.12 Tons Heating 24,226 44,358 Btu/h The FCL cassette type fancoil is a terminal unit for the conditioning of air in a room. The FCL concentrates high technological and functional features that make it the ideal means for air conditioning all environments. The supply of conditioned air is distributed throughout the room. The unit generates heat if included in a heating system with a boiler or heat pump but may also be used in the summer as an air conditioner if the heating system has a water chiller. The unit is mounted in a suspended-ceiling with the possibility of sending conditioned air to adjacent rooms and introducing external air independently from unit ventilation. The basic FCL unit is available in two versions, for two pipe and four pipe systems. VED / VEDi Fancoil Cooling 2.23 5.15 Btu/h Heating 51,248 85,573 Btu/h The VED fan coil is a ducted fancoil for both winter and summer operation. The units are designed to fit any ducted system. They can be integrated into the VMF system which allows the control of a single fancoil with accessories and the management of the VED introduced in complex fancoil networks. MZC Multizone Plenum MZC is a plenum with motorized dampers for zone and air control. It has been designed for residential and commercial applications. Further, it adjusts the flow rate of the air along with the damper to create a comfortable environment. 16 aermec.us
Fancoils VentilCassaforma Fancoil VentilCassaforma has been designed to suit modern interior architecture. It is a galvanized template that makes it possible to house fan coils in the wall. The template will make masonry work easier during the construction of a space where the fan coil will be installed. When the work is finished, the fan coil will be completely hidden from view. VentilCassaforma is available for fan coils in the FCX-USP series in two pipe systems or four pipe systems. 17 aermec.us
Air to Air Units 18 aermec.us
Air to Air Units CMP Heat Pump CMP units are packaged air to air heat pumps without the need for an outdoor unit. They are ideal for residential or small commercial buildings. The elegant design makes them suitable for a variety of room options. Cooling 0.67 Btu/h Heating 8,000 Btu/h Having no outdoor unit, the installation is extremely easy. Simply make two 6 holes in the perimeter wall, to allow the air conditioner to exchange heat with the outdoor environment. The unit is extremely slim (only 6.3 ) and minimizes the flow space required. The use of inverter compressor and fans reduces the energy consumption, improves temperature control, and guarantees extremely low sound levels. 19 aermec.us
Aermec North America 1608 Bonhill Road Mississauga Ontario L5T 1C7 Canada: 1-800-567-2221 US: 1-888-567-2227 aermec.us aermec.us/doc For Technical Assistance Contact: help@aermec.us 20 aermec.us