ATFLASH SENSOR USER GUIDE ATFLASH
INDEX A. INSTALLATION INSTRUCTIONS B. SENSOR: FIXING AND CONNECTIONS C. TURN ON/OF C.. TURN ON C.. TURN OFF 4 5 D. CONSOLE: FIXING AND CONNECTIONS E. LCD SCREEN INFORMATION 7 8 3 F. DRY CONTACT RELAYS INFORMATION G. TECHNICAL SPECIFICATIONS 9 0
LIGHTNING RISK 0km 30km 5km www.at3w.com ATFLASH A. INSTALLATION INSTRUCTIONS. For the installation of ATFLASH, 3 parts will be considered: : Always placed outdoors and above the roof. Provided with a multicore female connector. Cable: 5m cable Provided with a multicore male connector at one end (for connecting with the ) Console: Always placed indoors COMPONENTS: Mast ½, m long 4 4 Screws M8x0mm Anchorage pieces 5m connection cable console Power supply cable with schuko ATFLASH SENSOR
B. SENSOR: FIXING AND CONNECTIONS. Fix the anchorages to the wall. Pass the connecting cable through the mast and connect it to the sensor (see note). Fix the sensor to the mast with the provided 4 screws (M8). Place the mast with the sensor in the anchorage. The part of the cable running outdoors should be placed inside a guard tube. If this part is longer than meter then that tube should be fixed to the wall. The Console is a desktop device so no installation or special subjection is needed. The system is supplied with 5m connecting cable. Once the cable enters the building and reaches the place to be installed then it can be cut to the proper length (it has no connector). IMPORTANT CABLE CONNECTOR SENSOR CONNECTOR Fasten the cables in the connector. It is very important to follow carefully the color code: 3 4 5 Grey Brown White N.C. Yellow Pink/Shield Connect to the power supply. 5 Note: The connecting cable is provided with a ferrite in one of its ends. It must be inside the mast. Do not handle.
C. TURN ON/OFF. C.. TURN ON. Plug the power cable in the appropriate receptacle in the back of the console.. Plug the schuko into the power supply. 3. Use the ON/OFF switch to turn on the equipment. C.. TURN OFF. Use the ON/OFF switch to turn off the equipment.. If it is necessary to remove power cable, unplug the schuko to the power supply first. IMPORTANT NOTE: Provide the equipment a ground connection This equipment is connected to ground through the grounding line of the power supply. To avoid electrical shock connect always this conductor to a grounded socket
D. CONSOLE: FIXING AND CONNECTIONS. ATFLASH SENSOR LIGHTNING RISK LCD Screen Alarm indicator Led: Storm is located between 0-30Km 5 3 4 Alarm indicator Led: Storm is located between 30-5km Alarm indicator Led: Storm is located less than 5Km 0km 30km 5km www.at3w.com 3 4 5 7 Power indicator Led. No communication indicator Led. Switch ON/OFF and Power Schuko 7 8 8 Cable connector for the sensor 7 AC INPUT 0 ~ 50V-0.3A 50-0HZ DRY CONTACT RELAYS 4 9 9 Dry contact relays
E. LCD SCREEN INFORMATION. The LCD gives the information about the sensor state and the storm state with two lines of characters as follows: E.. SENSOR STATE E.. STORM STATE No communication between the sensor and the console. The sensor is sending wrong data NO COMMUNICATION ********************* DATA ERROR st Alarm Level nd Alarm Level STORM<0KM STORM<30KM 3 rd Alarm Level STORM<5KM 8 IMPORTANT NOTE: During the alarm state, the screen s first line changes in accordance to the proximity of the storm.
F.DRY CONTACT RELAYS INFORMATION. The Console is equipped with four free-contact outputs. Those outputs are four relays with two contacts: one normally open and the other normally closed. The connections are as follows: From left to right the configuration is:. No CONNECTION RELAY. 3rd ALARM LEVEL RELAY 3. nd ALARM LEVEL RELAY 4. st ALARM LEVEL RELAY 3 3 Normally open Common Normally closed 9
G. ATFLASH SENSOR TECHNICAL SPECIFICATIONS. OPERATING SPECIFICATIONS SENSOR MECHANICAL SPECIFICATIONS Detection Range 3 alarm levels Weight 347,5gr 0Km around the sensor Alarm sound Dimensions Ø70 x 95 mm Alarm levels 80 db Cable 5m SENSOR ELECTRICAL SPECIFICATIONS DC Voltage Protections +/- Vdc The sensor is protected against overcurrents and surges. Maximum separation distance Framework material IP Code Fixing 00m (optional cable) Polypropylene IP54 Fixed to ½ tube CONSOLE ELECTRICAL SPECIFICATIONS Power supply Frequency Power Relays outputs Protections 0-50Vac 50-0Hz 5 W 4 outputs (3 storm alarms and another one for no communication) Protected against overcurrents and surges. CONSOLE MECHANICAL SPECIFICATIONS Weight,3 Kg Dimensions 7 x 03 x 8 mm Material Galvanized steel MOUNTING SPECIFICATIONS Mast (depends on installation) ½ m galvanized steel mast included. 0 ENVIRONMENTAL SPECIFICATIONS working temperature -40 to 85ºC Console working temperature -0 to 85ºC Anchoring (depends on installation) Corrugated tube U-shaped anchorage consisting of galvanized steel, 30cm long support with screws for wall fixing (all included). Protection tube for communication cable included.
www.at3w.com HEADQUARTERS PARQUE TECNOLÓGICO DE VALENCIA, C/ NICOLÁS COPÉRNICO, 4 4980 PATERNA (VALENCIA), SPAIN T. (+34) 9 38 50 F. (+34) 9 38 0 atsa@at3w.com