Electric Water Heaters The Styleboiler range of electric storage water heaters offers an extensive array of models for the production of domestic hot water (D.H.W.) with a capacity ranging from 10 to 1000 litres and power ratings from 1.2 to 10 kw with single- and three-phase connections. The range meets both the domestic requirements of a typical home as well as those of industrial and collective settings. The product lines include rapid models, which are ideal for the rapid and cheap production of small quantities of water, smart models which are small water heaters designed for installations where limited space is available, the classic standard models devised to accommodate the essential basic requirements of the market, and also the interline product line, providing a large number of combinations to meet the highest expectations as regards quality in observance of European and international standards. The STRENGTHS of the product range in detail: > Thermal insulation Insulation layer made of very thick (Interline range) high-density polyurethane (PU) foam that guarantees excellent insulation. > Tank protection against wear Thanks to the flow-coating enamelling process at 850 C for guaranteed quality internal protection or via classic Teflon-coating. > Magnesium anode Featured in all the models in the range, this anode makes for effective electrochemical tank protection. > External Control Knob (SE) External control knob used to facilitate the water heater temperature adjustment, combined with the flange for easy inspection and cleaning. > Dual Safety Thanks to the presence of both an operating thermostat and a maximum temperature thermostat to avoid possible malfunctions. > IP Degree of Protection Styleboiler water heaters are safe because they are splash-proof and are specially designed for installation close to the water delivery points, even in public and collective settings. > Environmentally friendly SStyleboiler strives to optimise its industrial activity while respecting the environment. To minimise the environmental impact of its products, it has abolished the use of chlorofluorocarbons (CFC-HCFC) in the insulation (PU) layer and makes continuous efforts to use recyclable components. pg 22
Electric Water Heaters pg 23
wall-hung, storage, installation above or below the sink Rapid series 10-15-30 Rapid wall-hung electric storage water heaters are ideal for the rapid and cheap production of small quantities of water. They can be installed above or below the sink (30 Litres above only). Steel tank, glass-lined using the flowcoating method (850 C). a 1 1 4 coupling. Regulation and safety rod thermostat. Polystyrene insulating shells (EPS) for reduced heat loss. Shock-resistant polypropylene (PP) casing and back. Brackets for wall mounting available upon request. IPX5 protective cover over electrical parts. Heat. time Weight A B C D E F G l kw V min C Mpa Kg KW-WW mm mm mm mm mm mm mm Pony 10 10 1,2* 230 30 75 0,8 6,0 R ½ 261 251 450 228 100 62 189 Pony 10 s 10 1,2* 230 30 75 0,8 6,0 R ½ 261 251 450 228 100 62 189 Pony 15 15 1,2* 230 46 75 0,8 7,5 R ½ 296 285 498 248 100 69 216 Pony 15 s 15 1,2* 230 46 75 0,8 7,5 R ½ 296 285 498 248 100 69 216 Pony 30 30 1,2* 230 92 75 0,8 10 R ½ 366 355 568 384 100 89 266 Note: s = undersink version oversink version 10-15-30 undersink version 10-15 pg 24
wall-hung, storage, installation above or below the sink Rapid SE series 10-15-30 Rapid SE wall-hung electric storage water heaters are ideal for the rapid and cheap production of small quantities of water. They can be installed above or below the sink (30 Litres above only). The external control knob (SE) makes for easier adjustment of the water temperature. Steel tank, glass-lined using the flowcoating method (850 C). Tank inspection flange. a flange. Regulation and safety rod thermostat with external control knob. Polystyrene insulating shells (EPS) for reduced heat loss. Shock-resistant polypropylene (PP) casing and back. Brackets for wall mounting available upon request. IPX5 protective cover over electrical parts. External Control Knob Heat. time Max. operating Max. operating Weight A B C D E F G l kw V min C Mpa Kg KW-WW mm mm mm mm mm mm mm Pony 10/SE 10 1,2 230 30 75 0,8 6,0 R ½ 261 251 450 228 100 62 189 Pony 10/SE s 10 1,2 230 30 75 0,8 6,0 R ½ 261 251 450 250 100 62 189 Pony 15/SE 15 1,2 230 46 75 0,8 7,5 R ½ 296 285 498 248 100 69 216 Pony 15/SE s 15 1,2 230 46 75 0,8 7,5 R ½ 296 285 498 270 100 69 216 Pony 30/SE 30 1,2 230 92 75 0,8 10,0 R ½ 366 355 568 384 100 89 266 Note: s = undersink version oversink version 10-15-30 undersink version 10-15 pg 25
wall-hung, storage Smart series 30 Smart wall-hung electric storage water heaters are ideal for the rapid and cheap production of small quantities of water where the installation space is limited. Steel tank treated with thermo-hardening resins (Teflon) or glass-lined using the flow-coating method (850 C) depending on the model and/or version. a 1 1 4 coupling. Regulation and safety rod thermostat. CFC and HCFC-free polyurethane (PU) foam External casing made of sheet metal coated with epoxy powder paint. IPX3 protective cover over electrical parts (IPX2 for VB 30). Heat. time weight l kw V min C Mpa Kg KW-WW VO 30 25 1,2 230 77 75 0,8 12 R ½ Dimensional diagrams pg 26
wall-hung, storage Standard mini series 30 Standard mini wall-hung electric storage water heaters are ideal for the rapid and cheap production of small quantities of water where the installation space is limited. Steel tank treated with thermo-hardening resins (Teflon) or glass-lined using the flow-coating method (850 C) depending on the model and/or version. a 1 1 4 coupling. Regulation and safety rod thermostat. CFC and HCFC-free polyurethane (PU) foam External casing made of sheet metal coated with epoxy powder paint. IPX3 protective cover over electrical parts (IPX2 for VB 30). Heat. time weight l kw V min C Mpa Kg KW-WW V 30 30 1,2 230 92 75 0,8 12 R ½ Dimensional diagrams View from above pg 27
wall-hung, storage Standard series 50-80-100 Standard wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The water heaters are available in a vertical version, vertical universal left-right thermo version, horizontal version and horizontal thermo version. Steel tank treated with thermo-hardening resins (Teflon) or glass-lined using the flow-coating method (850 C) depending on the model and/or version. a 1 1 4 coupling. Regulation and safety rod thermostat; External casing made of sheet metal coated with epoxy powder paint. CFC and HCFC-free polyurethane (PU) foam IPX4 protective cover over electrical parts (IPX2 for versions V/T 50-80-100). Heat. time weight l kw V min C Mpa Kg KW-WW mm mm V 50 50 1,2 230 153 75 0,8 15,5 R ½ 509 281 V 80 80 1,2 230 245 75 0,8 20,5 R ½ 729 498 V 100 100 1,2 230 306 75 0,8 25,5 R ½ 879 648 A B Dimensional diagrams pg 28
wall-hung, storage Standard SE series 50-80-100 Standard SE wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The external control knob (SE) makes for easier adjustment of the water temperature. Steel tank, glass-lined using the flowcoating method (850 C). 88 mm tank inspection flange. a flange. Regulation and safety rod thermostat with external control knob. CFC and HCFC-free polyurethane (PU) foam External casing made of sheet metal coated with epoxy powder paint. IPX4 protective cover over electrical parts. External Control Knob Dimensional characteristics Heat. time weight l kw V min C Mpa Kg KW-WW mm mm V 50 SE 50 1,2 230 153 75 0,8 15,5 R ½ 509 281 V 80 SE 80 1,2 230 245 75 0,8 20,5 R ½ 729 498 V 100 SE 100 1,2 230 306 75 0,8 25,5 R ½ 879 648 A B Dimensional diagrams pg 29
wall-hung, storage Standard top series 40-50-80-100 Standard top wall-hung electric storage water heaters are designed to meet the highest expectations as regards quality in observance of European and international standards. The insulation layer is made of very thick high-density polyurethane (PU) foam to minimise heat loss. Steel tank, glass-lined using the flowcoating method (850 C). 134 tank inspection flange. a flange. External regulation and safety capillary thermostat. External casing made of sheet metal coated with epoxy powder paint. CFC and HCFC-free very thick polyurethane (PU) foam IPX5 protective cover over electrical parts complete with cable and plug. Heat. time. Insul. thickness Heat loss 65 C weight Dimensional characteristics A B l kw V min mm kwh/24h C Mpa Kg KW-WW mm mm ISWV 40 40 1,2 230 122 25 0,78 75 0,8 18,5 R ½ 513 292 ISWV 50 50 1,2 230 153 25 0,87 75 0,8 21,0 R ½ 596 375 ISWV 80 80 1,2 230 245 25 1,13 75 0,8 27,0 R ½ 799 587 ISWV 100 100 1,2 230 306 25 1,30 75 0,8 33,0 R ½ 1013 801 Note: * = 1.5 and 2.0 kw heating element available Dimensional diagrams pg 30
wall-hung, storage Standard thermo series 50-80-100 Standard thermo wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The water heaters are available in a vertical version, vertical universal left-right thermo version, horizontal version and horizontal thermo version. Steel tank treated with thermo-hardening resins (Teflon) or glass-lined using the flow-coating method (850 C) depending on the model and/or version. a 1 1 4 coupling. Regulation and safety rod thermostat. External casing made of sheet metal coated with epoxy powder paint. CFC and HCFC-free polyurethane (PU) foam IPX4 protective cover over electrical parts (IPX2 for versions V/T 50-80-100). Heat. time. weight Coil A B C D l kw V min C Mpa Kg KW-WW PV-PR mm mm mm mm V/T 50 50 1,2 230 153 75 0,8 17,0 R ½ Rp ½ 548 319 229 132 V/T 80 80 1,2 230 245 75 0,8 23,5 R ½ Rp ½ 779 550 229 363 V/T 100 100 1,2 230 306 75 0,8 27,5 R ½ Rp ½ 930 701 229 363 Dimensional diagrams pg 31
wall-hung, storage Standard SE series 120-150-200 Standard SE wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The external control knob (SE) makes for easier adjustment of the water temperature. Also recommended for industrial and collective use. Also available in the thermo version. Steel tank, glass-lined using the flowcoating method (850 C). 88 mm tank inspection flange. a flange. Regulation and safety rod thermostat with external control knob. CFC and HCFC-free polyurethane (PU) foam IPX4 protective cover over electrical parts. External casing made of sheet metal coated with epoxy powder paint. AccessorIes on page 39 External Control Knob Heat. time Weight A B l kw V min C Mpa Kg KW-WW mm mm V 120/ SE 120 1,5 230 294 75 0,8 29,0 R ½ 1029 605 V 150/SE 150 2,0* 230* 275 75 0,8 42,0 R ¾ 945 500 V 200/SE 200 2,0* 230* 367 75 0,8 51,5 R ¾ 1205 800 Note: * = 3.0 kw 230 and 400/3 V~ heating element available, in which case the external control knob SE is no longer required. version120 version 150/200 pg 32
thermoelectric WATER HEATERS wall-hung, storage Standard thermo SE series 120-150-200 Standard thermo SE wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The external control knob (SE) makes for easier adjustment of the water temperature. Also recommended for industrial and collective use. Also available in the thermo version. Steel tank, glass-lined using the flowcoating method (850 C). 88 mm tank inspection flange. Armoured copper heating elemen t fitted on a flange. Regulation and safety rod thermostat with external control knob. CFC and HCFC-free polyurethane (PU) foam IPX4 protective cover over electrical parts. External casing made of sheet metal coated with epoxy powder paint. AccessorIes on page 39 External Control Knob Heat. time Max. oper. Max. oper. weight Coil Heat exchange surface Power (Δt 35 K)** D.H.W. produc (Δt 35 K)** Primary flow rate l kw V min C Mpa Kg KW-WW PV-PR m² kw I/h m³/h mm mm V/T 120/SE 120 1,5 230 294 75 0,8 37,0 R ½ Rp ½ 0,6 19,0 469 2,0 605 1029 V/T 150/SE 150 2,0* 230* 275 75 0,8 56,5 R ¾ Rp ½ 0,9 33,0 810 2,0 945 500 V/T 200/SE 200 2,0* 230* 367 75 0,8 66,0 R ¾ Rp ½ 0,9 33,0 810 2,0 1205 800 Note: * = 3.0 kw 230 and 400/3 V~ heating element available, in which case the external control knob SE is no longer required. **= Primary circuit temperature 80 C / Secondary circuit temperature 10/45 C / Primary flow rate indicated in the table; D.H.W. = domestic hot water. A B version 120 version 150/200 pg 33
ELECTRIC WATER HEATERS wall-hung, horizontal storage Standard horizontal series 50-80-100 Standard horizontal wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The water heaters are available in a vertical version, vertical universal left-right thermo version, horizontal version and horizontal thermo version. Steel tank treated with thermo-hardening resins (Teflon) or glass-lined using the flow-coating method (850 C) depending on the model and/or version. External casing made of sheet metal coated with epoxy powder paint. CFC and HCFC-free polyurethane (PU) foam a 1 1 4 coupling. IPX4 protective cover over electrical parts (IPX2 for versions V/T 50-80-100). Regulation and safety rod thermostat. l kw V Heat. time. min 50 1,2 230 153 Capacity O 50 Power Voltage temp C press Mpa Weight 75 0,8 mm mm mm mm 15,5 R½ 538 165 184 234 A B C D O 80 80 1,2 230 245 75 0,8 20,5 R½ 758 220 294 344 O 100 100 1,2 230 306 75 0,8 25,5 R½ 908 370 369 419 Note: heating element fitting left or right. standard horizontal version 50-80-100 7 8 *.' )+. *+& AM : pg 34 Kg KW-WW MM '(& 9 (*+
wall-hung, horizontal storage Standard horizontal series 120-150-200 Standard horizontal wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. Also recommended for industrial and collective use. Available in the horizontal version only. Steel tank, glass-lined using the flow-coating method (850 C). 88 mm tank inspection flange. Corrosion-proof magnesium anode. Armoured copper heating element fitted on a flange. Regulation and safety rod thermostat. CFC and HCFC-free polyurethane (PU) foam IPX4 protective cover over electrical parts. External casing made of sheet metal coated with epoxy powder paint. Stored water temperature indicator. Heat. time Weight l kw V min C Mpa Kg KW-WW mm mm O 120 120 1,2 230 367 75 0,8 29,0 R ½ 1058 520 O 150 150 2,0 230 275 75 0,8 65,5 R ¾ 1024 530 O 200 200 2,0 230 367 75 0,8 71,5 R ¾ 1294 800 Nota: modelli 150-200 a corredo staffe per montaggio dx-sx Dimensional characteristics A B version 120 version 150/200 pg 35
thermoelectric WATER HEATERS wall-hung, storage horizontal Standard horizontal thermo series 80-100 Standard horizontal thermo wall-hung electric storage water heaters are the basic product range devised to cater for the most varied market requirements. The water heaters are available in a vertical version, vertical universal left-right thermo version, horizontal version and horizontal thermo version. Steel tank treated with thermo-hardening resins (Teflon) or glass-lined using the flow-coating method (850 C) depending on the model and/or version. Armoured copper heating element fitted on a 1 1 4 coupling. Corrosion-proof magnesium anode. Regulation and safety rod thermostat. External casing made of sheet metal coated with epoxy powder paint. CFC and HCFC-free polyurethane (PU) foam IPX4 protective cover over electrical parts (IPX2 for versions V/T 50-80-100). Stored water temperature indicator. Heat. time. temp press Weight Coil A B C D l kw V min C Mpa Kg KW-WW PV-PR mm mm mm mm O/T 80 80 1,2 230 245 75 0,8 26,5 R ½ Rp ½ 807 370,5 316,5 220 O/T 100 100 1,2 230 306 75 0,8 31,6 R ½ Rp ½ 930 418,5 391,5 370 Dimensional diagrams pg 36
floor-standing storage Interline series 120-160-200-300-400-500-600 Interline floor-standing electric storage water heaters are designed to meet the highest expectations as regards quality in observance of European and international standards. The insulation layer is made of very thick high-density polyurethane (PU) foam to minimise heat loss. They are ideal for collective and industrial use. Steel tank, glass-lined using the flowcoating method (850 C). 134 mm front inspection hatch. the hatch. Regulation and safety thermostat. External coloured plastic (PVC) coating. CFC and HCFC-free very thick polyurethane (PU) foam IPX5 protective cover over electrical parts. AccessorIes on page 39 Heat. Time. Insul. thickness Heat loss 65 C Max. oper. Max. oper. weight Recirculation A B C D E F l kw V min mm kwh/24h C Mpa Kg KW-WW Z mm mm mm mm mm mm ISS 120 120 1,5 230 294 50 1,50 75 1,0 38 Rp ¾ Rp ¾ 610 620 854 150 486 720 ISS 160 160 2,0 230 294 50 1,70 75 1,0 46 Rp ¾ Rp ¾ 610 620 1056 150 551 922 ISS 200 200 2,0 230 367 50 2,00 75 1,0 53 Rp ¾ Rp ¾ 610 620 1329 150 651 1195 ISS 300 300 3,0 230 367 50 2,40 75 1,0 77 Rp 1 Rp 1 650 675 1560 148 828 1408 ISS 300/3 300 3,0 400/3 367 50 2,40 75 1,0 77 Rp 1 Rp 1 650 675 1560 148 828 1408 ISS 400/3 400 4,0 400/3 367 50 2,80 75 1,0 99 Rp 1 Rp 1 750 775 1553 162 782 1387 ISS 500/3 500 5,0 400/3 367 50 3,30 75 1,0 115 Rp 1 Rp 1 750 775 1818 162 932 1652 ISS 600/3 600 5,0 400/3 440 50 3,60 75 1,0 176 Rp 1 Rp 1 810 832 1819 124 871 1659 Dimensional diagrams pg 37
storage type, floor-standing Interline high storage series 800-1000 Interline high storage floor-standing electric storage water heaters are designed to meet the new expectations of the market as to durability and great storage. To this end, this new high-capacity product line was introduced, providing maximum quality and durability owing to the use of special materials and sophisticated technological solutions. The guarantee of durability in time is further extended by means of a modern glass-lining treatment over the tank. The insulation layer is manufactured by means of a new system that combines the technology of the injected polyurethane (PU) with the flexibility of NEOPOR (EPS). This solution allows the installer to have a plug and play product and, in case of need, it is an easy solution for making the product pass through openings whose width equals 800 mm. This system allows a troublefree disassembly and re-assembly of the insulation layer for an easier installation in boiler rooms. The two big front hatchways characterise the line of these products and make them flexible and suitable for several combinations of electrical powers up to maximum 20 kw. The electrical components are supplied apart in handy single- and three-phase KITs with Incoloy 800 stainless steel heating elements with powers up to 10 kw or made of copper up to 5 kw. Furthermore, you can equip the tank with spiroid exchangers, if any, which can be installed in the hatchways. They are recommended for collective use. Glass-lined steel boiler. External coloured plastic coating. INOX Stainless Steel Heating Element KIT Double Ø 134 mm front hatchway for electrical Kit assembly and inspection. Ø 134 mm top bottom-flange complete with counter-flange. Very thick expanded polyurethane (PU) / (EPS) Easy entry system. Adjustable feet for floor standing. AccessorIes on page 70 Capacity Insul. thickness Weight Recirculation A B C D E F l mm C Mpa Kg KW-WW Z mm mm mm mm mm mm ISS 800 800 >100 95 1,0 146 Rp 1 ¼ Rp 1 ¼ 880 925 1865 191 1071 1676 ISS 1000 1000 >100 95 1,0 170 Rp 1 ¼ Rp 1 ¼ 880 925 2245 191 1263 2056 Dimensional diagrams pg 38
ELECTRIC WATER HEATER KITS AND ACCESSORIES Accessories & kit for Electric Water Heaters Standard interline SINGLE-, THREE-PHASE TRANSFORMATION ELECTTRICAL KIT formed by: 2 heating element - 3.0 kw - 400/3 V~ installed on the flange, flange gasket, three-phase thermostat and closing cover ONLY FOR SERIES V E V/T 120-150-200 2.0 kw 230 V~ 1 SINGLE-PHASE ELECTRICAL KIT formed by: counter-flange with 1 sleeve, gasket, copper armoured heating element and thermostat 3.0 kw 230 V~ 1 SINGLE-PHASE ELECTRICAL KIT formed by: counter-flange with 1 sleeve, gasket, copper armoured heating element and thermostat interline 3.0 kw 400/3 V~ 2 THREE-PHASE ELECTRICAL KIT formed by: counter-flange with 2 sleeve, gasket, copper armoured heating element, thermostat equipped with brackets and connectors 4.0 kw 400/3 V~ 2 THREE-PHASE ELECTRICAL KIT formed by: counter-flange with 2 sleeve, gasket, copper armoured heating element, thermostat equipped with brackets and connectors 5.0 kw 400/3 V~ 2 THREE-PHASE ELECTRICAL KIT formed by: counter-flange with 2 sleeve, gasket, copper armoured heating element, thermostat equipped with brackets and connectors interline SPIROID EXCHANGER KIT 1.0 sqm formed by: counter-flange, finned coil made of tinned copper 1 sqm; gasket, union set, round grill, fastening screws and nuts FOR ALL SERIES SPIROID EXCHAGER KIT 1.8 sqm ONLY FOR SERIES 400-500-600-800-1000 formed by: counter-flange, finned coil made of tinned copper 1.8 sqm; gasket, union set, round grill, fastening screws and nuts Interline 4.0 8.0 kw 400/3 V~ THREE-PHASE INOX ELECTRICAL KIT formed by: counter-flange, gasket, three-element Incoloy 800 stainless steel heating element, thermostat and support bracket RECOMMENDED FOR SERIES 400-500-600-800-1000 4.0 8.0 kw 400/3 V~ THREE-PHASE INOX ELECTRICAL KIT formed by: counter-flange, gasket, three-element Incoloy 800 stainless steel heating element, thermostat and support bracket. RECOMMENDED FOR SERIES 400-500-600-800-1000 5.0 10.0 kw 400/3V~ THREE-PHASE INOX ELECTRICAL KIT formed by: counter-flange, gasket, three-element Incoloy 800 stainless steel heating element, thermostat and support bracket. RECOMMENDED FOR SERIES 400-500-600-800-1000 pg 39