INSTRUCTION SHEET Longitudinal Lateral *(XX) = Finish Specifier Sway Brace assemblies are intended to be installed in accordance with NFPA -13 and the manufacturer's installation instructions. The required type, number, and size of fasteners used for the structure attachment fitting shall be in accordance with NFPA-13. Installation Angle from Vertical * All Brace and Service Pipes shown, not included WARNING: 1. ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at and from your ERICO customer service representative. 2. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings. 3. All instructions must be completely followed to ensure proper and safe installation and performance. 4. Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property damage, serious bodily injury and death. 5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any other purpose. NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted. The customer is responsible for: a. Conformance to all governing codes. b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer. c. Using appropriate industry standard hardware as noted above. SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application. Dyna-Flow is a registered trademark of Allied Tube and Conduit Corporation. EZ FLOW is a trademark of Northwest Pipe Company. FM is a registered certification mark of FM Approvals LLC, LTD. NFPA is a registered trademark of National Fire Protection Association, Inc. UL is a registered trademark of UL LLC. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 1 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
UL Loads (Listed for Restraints) - Lateral** Part Number Dyna-Flow Service Pipe Sch 10 Service Pipe Sch 40 Service Pipe 0100(XX) 655 lb (2,914 N) 655 lb (2,914 N) 0125(XX) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N) 0150(XX) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N) Part Number 0200(XX) 0250(XX) 0300(XX) 0400(XX) 0500(XX) 0600(XX) Dyna-Flow Service Pipe UL Loads (Listed for Sway Braces) Lateral* EZ FLOW Service Pipe 0800(XX) 1000(XX) Sch 10 Service Pipe Longitudinal** Sch 40 Service Pipe Service Dyna-Flow Pipe Service Mega-Flow Pipe Sch 10 Service Pipe Sch 40 Service Pipe 1. UL Listed for use with Lightwall Service Pipe, Schedule 10, and Schedule 40 Service Pipe, for use with 1 to 2 NPS Schedule 40 brace pipe or 1/4" angle iron (except for 10-inch). *2. **2015 lbs. [8960 N] load rating when used with 1/4" angle iron. **3. Rating with 1/4" angle iron is identical to Schedule 40 brace pipe. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 2 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
Notes: A) FM approved when used with 1", 1-1/4" or 2" (DN25, DN32, DN40, DN50) NPS Schedule 40, GB/T 3091, EN 10255 (Heavy), AS 1074 (Heavy) or JIS G3454 brace pipe. B) Load ratings for Schedule 40 above may also be applied to AS 1074 (Heavy), GB/T 3091, EN 10255 (Heavy) and JIS G3454 pipe. C) Load ratings for Schedule 40 above may also be applied to AS 1074 (Meduim), GB/T 3091, EN 10255 (Medium or Heavy), JIS G3452, FM approved Thinwall, and Schedule 40 pipes unless otherwise indicated. D) Load ratings for LW above refers to FM Approved Lightwall Pipe, commonly referred to as "Schedule 7". These ratings may also be applied to A1074 Lightwall, EN 10255 L, EN 10220, and GB/T 8163 pipe unless otherwise specified. E) Load ratings for "0.188 wall" above may be applied to any thicker walled pipe unless otherwise specified. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 3 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
INSTRUCTION SHEET #1 #2 Position stamped components around service pipe #3 #4 Tighten top and bottom nuts to proper torque, reference torque chart. *(XX) Finish Specifier Finger tighten nuts and rotate assembly to desired orientation Insert brace into clamp as far as possible. Tighten set screw until head snaps off is a. It is intended to be combined with a CADDY brand Structural Attachment Fitting and "Bracing Pipe" to form a complete bracing assembly. Sway Braces are intended to be installed in accordance with NFPA -13 and the manufacturer's assembly and instructions. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 4 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 5 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 6 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 7 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 8 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 9 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 10 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 11 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
The CSBBARJ can be installed as shown on the top flange of an I-Beam with tapered or non-tapered flanges. The CSBBARJ can be installed as shown on the top flange of an I-Beam with tapered or non-tapered flanges. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 12 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 13 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 14 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 15 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
Through bolt shown. A lag screw may also be used. Through bolt shown. A lag screw may also be used. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 16 OF 17 2009, 2011, 2012, 2013, 2014 ERICO
Through bolt shown. A lag screw may also be used. Through bolt shown. A lag screw may also be used. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO 17 OF 17 2009, 2011, 2012, 2013, 2014 ERICO