Grounded stainless steel shelves, hinges and door latches for ESD safety*

Desiccator Cabinets PELCO Desiccator Cabinets Chrome-plated wire racks support desiccator shelving, shelf height adjustable every 1 2" Stainless steel shield mounted at base of compartment prevents scratching of material and allows items to be stored on a grounded surface* Locking* lift latches provide excellent security Stainless steel door stiffener gives even distribution of latch force* Easy opening doors are fabricated with acrylic bar reinforcements to prevent door warpage Micron-Aire Pure Purge provides fully automatic control over nitrogen purging and humidity set point* Plenum chamber covering the complete back of the cabinet with vent holes into chamber allows an even flow of nitrogen to compartment* Closed cell gasketing for a leak proof door seal Pressure relief valve continuously bleeds off excess internal pressure to maintain a safe positive pressure within the desiccator, which extends the life of desiccator doors and gasketing* *Asterisk refers to optional features Grounded stainless steel shelves, hinges and door latches for ESD safety* For Economical Dust-Free & Moisture-Free Storage Three Types of Desiccator Cabinets Offered 1. Standard Desiccator Cabinets 2. Amber Colored Desiccator Cabinets 3. Static Dissipative PVC - considered the best protection from ESD Locking Lift Latch (optional) - Provides excellent tamperproof security. Guaranteed to provide a snug fit even for those frequently used desiccators. Door Stiffeners (optional) - For added strength. Standard Desiccator Cabinets Desiccator cabinets are designed for economical dust and moisture-free storage and protection of microelectronic devices, subminiature parts, semiconductor wafers, biochemical mixtures, and electronic subassemblies. The cabinets are constructed of 1 4" solvent bonded acrylic, featuring easyopen doors and 360 o visibility. The doors are fabricated with acrylic bar enforcements to prevent door warpage, assuring a positive seal. Chrome plated wire shelf sliders support a variety of shelf types at 1 2" intervals for best utilization of interior space. The base of divider floor and the inside divider wall are perforated. Desiccators with ESD Protection We offer desiccators for protection against Electro Static Discharge, utilizing a special Static Dissipative PVC. This Static Dissipative type is available in all the standard sizes and configurations as shown in the table on the next page. Custom designs and size requirements are also accepted for consideration. 1

Desiccator Cabinets Static Dissipative PVC This group is considered the best protection from ESD. Product Features and Specifications: 5mm clear dissipative PVC Surface resistivity: 10 6-10 7 Ohms Square Surface potential: Less than one second UL (94V-0) approved A (clear) 12" x 12" x 12" One Door D 24" x 18" x 24" Two Doors Grounded Hinges Equipped with grounded hinges, door latches and racking system - all grounded to the same plane which includes a ground lug for attachment to facility ground, thus neutralizing personnel when opening the cabinet. Amber desiccators protect items inside from UV rays. A (amber) 12" x 12" x 12" One Door B 16" x 16" x 16" Two Doors E 12" x 12" x 24" Two Doors C 18" x 18" x 18" Two Doors F 18" x 18" x 27" Three Doors Style W x D x H In. W x D x H cm Clear Static Dissipative Amber A 12 x 12 x 12 30.4 x 30.4 x30.4..............22600**...................22600-dsp...................22601*** B 16 x 16 x 16 40.6 x 40.6 x 40.6..............22602*...................22602-DSP...................22603* C 18 x 18 x 18 45.7 x 45.7 x 45.7..............22604*...................22604-DSP...................22605* D 24 x 18 x 24 61 x 45.7 x 61...............22606*...................22606-DSP...................22607* E 12 x 12 x 24 30.4 x 30.4 x 61...............2263.....................22635-DSP...................22628 F 18 x 18 x 27 45.7 x 45.7 x 68.5..............22623....................22623-DSP...................22643 G 24 x 24 x 36 61 x 61 x 92...............22610*...................22610-DSP..................22611* H 48 x 24 x 48 122 x 61 x 122..............22612*...................22612-DSP..................22613 I 24 x 24 x 60 61 x 61 x 152..............22634....................22634-DSP...................22624 J 48 x 24 x 60 122 x 61 x 152..............22614*...................22614-DSP..................22615* K 24 x 24 x 48 61 x 61 x 122..............22621....................22621-DSP..................22622 * Includes one clear acrylic shelf for compartment; ** Includes three clear acrylic shelves per cabinet *** Includes two clear acrylic shelves per cabinet 2 TED PELLA, INC.

Desiccator Cabinets G 24" x 24" x 36" Three Doors J 48" x 24" x 60" Ten Doors I 24" x 24" x 60" Five Doors H 48" x 24" x 48" Eight Doors K 24" x 24" x 48" Four Doors Perforated Non Perforated Perforated Stainless Non Perforated Stainless Perforated Stainless Clear Acrylic Shelf Clear Acrylic Shelf Steel Shelf Steel Shelf Steel Shield A 22600-3P....................... 22600-3.................22600-1.................. 22600-2.................22644 B 22602-3P....................... 22602-3.................22602-1.................. 22602-2.................22645 C 22604-3P....................... 22604-3.................22604-1.................. 22604-2.................22640 D 22606-3P....................... 22606-3.................22606-4.................. 22606-2.................22646 E 22600-3P....................... 22600-3.................22600-1.................. 22600-2.................22644 F 22604-3P....................... 22604-3.................22604-1.................. 22604-2.................22640 G 22610-3P....................... 22610-3.................22610-4.................. 22610-2.................22642 H 22610-3P....................... 22610-3.................22610-4.................. 22610-2.................22642 I 22610-3P...................... 22610-3.................22610-4.................. 22610-2.................22642 J 22610-3P....................... 22610-3.................22610-4.................. 22610-2.................22642 K 22610-3P....................... 22610-3.................22610-4.................. 22610-2.................22642 3

Desiccator Cabinets, Optional Features and Accessories Micron-Aire Pure Purge System Provides fully automatic control over the humidity impurity levels in your desiccator environment. A built-in relative humidity monitoring system maintains preset relative humidity within ±3% by reading the humidity levels in the desiccator. The system uses a fastresponse capacitive probe to measure internal humidity over the full range from 0-100% R.H. to control nitrogen purging. It is equipped with an advanced monitoring and alarm system. The Micron-Aire Pure Purge will let you know when any desired preset condition changes. Alarms included on the system are: Low supply of nitrogen source; high internal pressure; door open condition; drop in pressure. The Micron-Aire provides economical use of nitrogen. Outstanding Advantages: Protects stored parts against contamination Maintains relative humidity to within ±3% Relative Humidity ( R.H. ), easy to use R.H. controls give you precise control over internal humidity levels Prevents moisture buildup caused by hygroscopic characteristics of acrylic and other plastics Prevents door warpage and gasketing displacement by precisely maintaining the required internal nitrogen pressure 22625 Micron-Aire Pure Purge System NOTE: Must also order the Door Sensor, Prod. No. 226085, to make the purge system work. One sensor needed per door. 226085 Pure Purge Door Sensor, Flowmeter Precisely displays the volume of nitrogen flow to any cabinet - inlets are provided for mounting flowmeters on the PELCO Desiccator Cabinets. 22619 Flowmeter, 10-100 SCFH, 22619-1 Flowmeter, 0-20 SCFH, Pressure Relief Valve Continuously bleeds off excess internal pressure to maintain a safe positive pressure within the desiccator, which will extend the life of desiccator doors and gasketing. One should be used on chamber, especially when using the Micron-Aire Pure Purge system. 22617 Pressure Relief Valve, Mobile Desiccator Mobile Desiccator with Cart for storing and transporting. Constructed from 0.5mm Static Dissipative PVC with chrome plated wire rack shelf supports, adjustable every 1 /2". Slide out shelving sold separately, see below. Unit has a quick connect/disconnect fitting for the purging of nitrogen while stationary. 22616 39" x 25" x 36", Mobile Desiccator with Cart, Static Dissipative, Shelving Options 22647 Stainless Steel Perforated Shelf for Mobile Desiccator, 22648 Stainless Steel Perforated Shield for Mobile Desiccator, (see photo below). Stainless Steel Shields, Perforated 22644 12" x 12" Stainless Steel Shield, 22645 16" x 16" Stainless Steel Shield, 22640 18" x 18" Stainless Steel Shield, 22646 24" x 18" Stainless Steel Shield, 22642 24" x 24" Stainless Steel Shield, Stainless Steel Shelves, Perforated 22600-1 12" x 12" Stainless Steel Shelf, 22602-1 16" x 16" Stainless Steel Shelf, 22604-1 18" x 18" Stainless Steel Shelf, 22606-4 24" x 18" Stainless Steel Shelf, 22610-4 24" x 24" Stainless Steel Shelf, 4 TED PELLA, INC.

Painted Steel Stands 6" or 12" high (you may choose height) Powder coated for durability. 22600-6 12" x 12" Painted Steel Stand 22602-6 16" x 16" Painted Steel Stand 22604-6 18" x 18" Painted Steel Stand 22626 18" x 24" Painted Steel Stand 22636 24" x 24" Painted Steel Stand 22627 24" x 48" Painted Steel Stand Casters For use with the painted steel stands. Turns your stationery cabinet into a mobile unit. Steel framing, rubber wheels for quiet movement. 22629 Casters, set of 4 (2 with brakes) Mini Desiccator This small desiccator is 75mm in diameter and holds 12 pin-type specimen mounts under partial vacuum. It's flat design permits easy stacking and is shatterproof. The Mini-Desiccator is ideal for transporting specimens. 16190 Mini Desiccator, Small Desiccator Cabinet stackable, polystyrene, NO gas ports Perfect for cramped locations, these desiccator cabinets may be safely stacked up to five high. The cabinet is completely transparent from any side. The door has a foam rubber gasket and two roller latches for an airtight seal. When opened, the door slides into an out-of-the-way compartment beneath the cabinet. A jar of silica gel is included with cabinet. Inside dimensions: 8-1 4" x 7" x 5" high (21 x 18 x 13cm). Door opening: 7-1 2" x 4-3 8" high (19 x 11cm). Overall dimensions: 9-1 4" x 8-7 8" x 6-3 4" high (23 x 22 x 17cm). 2248 Small Desiccator Cabinet, Small Desiccator Cabinet with gas ports Two gas ports added to the rear of the No. 2248 Desiccator Cabinet allow an atmosphere to be created that may be altered and maintained at any concentration desired. The gas ports, located at Desiccator Cabinets top and bottom, create a sweep of gas from the inlet through the outlet. The gas ports have leakproof 4mm stopcocks and the door has an excellent seal. Useful for tissue culture work where a controlled carbon dioxide atmosphere is required or for flooding the chamber with nitrogen to eliminate oxygen. Dimensions are the same as for the No. 2248, plus the 2-3 4" (7cm) extension of the stopcocks. 2252 Small Desiccator w/gas Ports, Tall Desiccator Cabinet with dial hygrometer Molded of methyl methacrylate, this desiccator cabinet offers a clear view of contents. Shelf cleats allow for 15 levels of placement. Includes 3 sets of shelf rails and 3 clear shelves with small vent holes. The door has a full gasket, 2 metal hinges, 2 latches, and a handle. Door opening: 10" x 17-7 8" high (25 x 45cm). Inside depth:13-1 4" (34cm). Overall dimensions: 12-1 2" x 15-1 4" x 20" high (32 x 39 x 51cm). includes desiccant tray 22650 Tall Desiccator Cabinet, 5

Desiccator Cabinets; Desiccators, Vacuum Horizontal Desiccator Cabinet with dial hygrometer This desiccator cabinet is similar to the tall model but designed in a horizontal configuration. 8 levels of shelf cleats allow for placement of 2 sets of shelf rails and 2 clear shelves with small vent holes. The door has a full gasket and 2 metal hinges, 2 latches, and a handle. Door frame inside dimensions: 17-7 8" x 10" high (45 x 25cm). Inside depth: 13-1 4" (34cm). Overall dimensions: 14-3 4" x 19-5 8" x 13-3 4" high (37 x 50 x 35cm). includes desiccant tray 2254 Horizontal Desiccator, a red pilot light. After regeneration of silica gel, the cycle repeats. 2256 Horizontal Auto-Desiccator, 110V,........$960.00 22618 Replacement Dial Hygrometer for above cabinets, 35.75 2256-2 Additional Shelf......62.50 Vacuum Desiccators (polypropylene/polycarbonate) Clear top, white bottom vacuum desiccators a slow, gentle entrance of air to prevent unnecessary turbulence and specimen damage. Stopcock handle is high-visibility red. Port accepts 1 4" (6.4mm) I.D. tubing. Neoprene O-Ring O-ring seal does not require grease, but is not harmed if grease is used. Seal is unaffected by low temperatures down to 0 C. Polypropylene Bottom Section Provides excellent chemical resistance and permits the use of incandescent crucibles with standard size porcelain plates. The base of the all clear version is polycarbonate. Perforated Plate Polypropylene plate supplied is 1 8" (3.2mm) thick with 1 8" diameter perforations for air transfer. Plate rests on the retaining ledge of bottom section and has a center hole for easy removal. Small inches mm Flange O.D...........6-3 4 171 Inside Diameter.......5-7 8 149 Takes Plate..........No. 3 140 Overall Height........8-1 8 206 Clearance Above Plate..4-3 4 121 Horizontal Auto-Desiccator Cabinet with auto regeneration cycle This auto-desiccator cabinet features an adsorption/regeneration cycle for the silica gel desiccant. No desiccant tray is needed. The gel is contained in the control section, where it absorbs moisture to maintain a low (30-40%) relative humidity. The adsorption period lasts 4-1 2 hours, indicated by a green pilot light. After this period, the silica gel is regenerated for a 1 2 hour period, indicated by Clear top and bottom vacuum desiccators Large Interior Volume The space-saving design of the desiccator dome provides maximum interior clearances, giving an average of 13% greater interior volume than standard hemispherical domes. Extra Heavy Walls Clear polycarbonate top and white polypropylene bottom (clear base is polycarbonate) have extra heavy walls to eliminate the danger of implosion. This strong, shatterproof desiccator will hold a vacuum of 740mm of Hg (.09MPa) for a period of 24 hours. Stopcock with PTFE Plug The polypropylene stopcock has a PTFE plug which turns easily, allowing 2240 Vacuum Desiccator, Small, Clear Top, White Bottom, 2240-1 All-Clear Vacuum Desiccator, Small, 2240-3 Cartridge Desiccant, Small, Medium inches mm Flange O.D...........9-1 16 230 Inside Diameter.......7-3 4 197 Takes Plate..........No. 4 190 Overall Height........10-1 4 260 Clearance Above Plate..6-3 16 157 2244 Vacuum Desiccator, Medium, Clear Top, White Bottom, 2244-1 All-Clear Vacuum Desiccator, Medium, 2244-3 Cartridge Desiccant, Medium, continued, next page 6 TED PELLA, INC.

Desiccators, Vacuum; Desiccant, Cartridge; Accessories Large inches mm Flange O.D...........10-3 4 273 Inside Dia............9-7 /16 240 Takes Plate.........No. 5 230 Overall Height........12-1 8 311 Clearance above plate...7-3 /4 197 2246 Vacuum Desiccator, Large, Clear Top, White Bottom, 2246-1 All-Clear Vacuum Desiccator, Large, 2246-3 Cartridge Desiccant, Large, Cartridge Desiccant Eliminate the messy, timeconsuming job of changing loose desiccant. Convenient, easy-to-handle Desiccant in a Cartridge fits into the bottom section of standard glass or plastic desiccators. The cartridge consists of a durable polyester-felt bag with a perforated Mylar cover sealed in place. It is filled with indicating silica gel beads which change color from blue when moist. Saturated gel can be regenerated in a 300 F (150 C) vented oven for 3 hours or more (depending on size) until blue color returns. May be reactivated repeatedly without degradation. Individually sealed in a moisture-proof pouch. Prod. No. Desiccator Cartridge Weight Diameter Diameter lbs. 2240-3 160mm 114mm 1 2 0.23 2244-3 200mm 197mm 1-1 2 0.68 2246-3 250mm 238mm 3 1.36 Vacuum Chamber and Plate This low-cost Vacuum Chamber is useful for vacuum drying, degassing procedures, or demonstrations. It withstands a full vacuum at room temperature. The chamber is molded of clear polycarbonate for full visibility. The strong plastic plate has an O-ring which seals against the chamber's flange. The polypropylene stopcock has a Teflon plug and accepts 1 4" (6.4mm) I.D. tubing. Chamber I.D. is 7-7 8" (20cm) and maximum inside height is 4-3 8" (11cm). Plate is 1-3 4" high (44mm) x 9-1 8" (232mm) in diameter. 2259 Vacuum Chamber and Plate, Vacuum-Pressure Indicator see at a glance whether your desiccator is under vacuum or not The Vacuum-Pressure Indicator is a tool that fits in between the desiccator dome and the desiccator stopcock. No tools are required for its installation. It slips onto the tapered outlet of the desiccator dome and into the standard desiccator stopcock. The bellows, molded of an engineering thermoplastic elastometer, collapses when there is a negative pressure (vacuum) in the desiccator, and expands when under ambient atmospheric pressure. 2240-5 Vacuum Pressure Indicator, Replacement Stopcocks Polypropylene body with PTFE plug and washer, bright red handle and nut. Taper fits on desiccator port. The Stopcock is 3-way for vacuum draw, shut-off and vacuum release. 2240-4 Replacement Stopcock for Vacuum Desiccators, 7

Desiccators, Vacuum; Glass; Desiccant; Mini Hot Vac; Steel the baseplate. A digital thermometer measures the plate temperature. What a modest, inexpensive and effective way to cure embedments or dry samples while degassing them! Inside dimensions are 6" Dia. x 3" H (15.3 x 7.6cm) 2245 PELCO Mini Hot Vacuum Desiccator, Glass Vacuum Desiccators and Desiccant the Dry-Seal desiccators that seal without grease on the flange The lid can be removed when needed and rested on a countertop without the danger of dust and dirt adhering to a greasy surface. The lid lifts up instead of sliding sideways. It is recommended that the sleeve valve be lubricated with silicone based vacuum grease to increase performance and prevent freezing. "810" brand glass. Includes: Cover, Sleeve Valve, Silicone Sealing Ring, Retaining Ring for Sleeve Valve and Aluminum Plate. Inside Dia., mm 150 250 Sleeve Joint 40/35 55/38 Body Depth, mm 51 93 2275 Vacuum Desiccator, Glass, 150mm size, 2276 Vacuum Desiccator, Glass, 250mm size, Desiccant Packs for Glass Vacuum Desiccators Designed for the 150mm and 250mm sizes. The desiccant pack is placed in the bowl of the desiccator under the aluminum plate to preserve an anhydrous atmosphere within the evacuated desiccator. The desiccant is enclosed in fabric and perforated plastic for a dust-free environment and is supplied in a sealed foil package. Reactivation is carried out (after the Pack loses its blue color and turns pink) by placing the desiccant, with perforated side down, in a vented oven and heating for about three hours at about 150 C (300 F) or until the blue color returns. 2276-7 Desiccant Pack, Dry-Seal 250mm size, PELCO Mini Hot Vac Vacuum Desiccator vacuum and heat can act as a desiccator or mini-drying station An inexpensive way to warm embedding plastics while removing gas bubbles. The aluminum base is placed on a laboratory heating plate. A vacuum can be drawn through a provided porthole in PELCO Vacuum Desiccator Sturdy powder coated stainless steel constructed vacuum desiccator for storing electron microscopy samples and standards, photographic film, forensic specimens, etc. Dry, dark, dust-free storage maintain moisture-free conditions. This design from our shop offers: square corners to give more efficient storage space sturdy stainless steel materials effective vacuum sealing Store photographic films or reels, calibration standards and electron microscopy samples. Provided with vacuum gauge (inches of mercury, 0-30") and an on-off valve. Inside dimensions are 12" square (30.5cm sq.). One adjustable and removable shelf included. 2251 PELCO Vacuum Desiccator, ea. 3436 Oil-less Diaphragm Vacuum Pump*, 115V, 60Hz *see page 471 for more information on the Diaphragm Vacuum Pump 8 TED PELLA, INC.

Desiccant Dri-Can reusable desiccant canister The Dri-Can canister is ideal for desiccator cabinets, making trays of loose desiccant obsolete. The silica gel inside adsorbs moisture through perforations in the aluminum case. A canister maintains a safe level of humidity in 3 cu. ft. (0.11m3) of space. Also good for calibration standards and support filmed grid storage, camera cases, or other storage areas; designed to prevent rust and moisture invasion. It can be regenerated in a 300 F (150 C) oven in about 3 hours. A monitor window shows blue when recharged. 19950 Reusable Desiccant Canister, DRICAP Capsule Dehydrators excellent for SEM specimen containers DRICAP Capsules have more desiccant in less space and more drying power. Further advantages are: siftproof, non-linting, controlled adsorption rate, can be mechanically handled, color capacity indicator, saves weight and space. It is rugged and super activated, in addition to reducing humidity. Capsules can also protect against potency losses, fermentation, odor formation, color changes, corrosion, mildew, caking and condensation. The moisturepermeable cartridge shell is fabricated from clear cellulose acetate; the desiccant is activated SiO 2. Type 11 Desiccant Weight, 0.97g; (8 x 22mm) Type 14 Desiccant Weight, 1.85g; (8 x 40mm) 19953 DRICAP Capsule Dehydrators, Type 11, pkg/100 19956 DRICAP Capsule Dehydrators, Type 14, pkg/100 Bulk Desiccant 3,000,000 square feet of moistureadsorbing surface area in 1 pound This efficient drying is carried out by a hard, clear, porous, beaded, amorphous form of silica gel. The desiccant has a myriad of microscopic pores which explains its great moisture-attracting capacity. Translucent beads look and feel dry even when saturated. Dust-free and attrition-proof. May be regenerated by heating with no loss of efficiency. 19960 Bulk Desiccant, 2 lbs. (0.9kg) 19961 Bulk Desiccant, 5 lbs. (2.27kg) Reactivation of Desiccant on this page may be carried out (after desiccant loses its blue color and turns pink) by placing the desiccant in a vented oven and heating for about three hours at about 150 C (350 F) or until the blue color returns. Vacu-Storr High Vacuum Storage Vessels 5-year holding time to 0.1Atm res 10-6 torr! The Vacu-Storr series of vacuum containers were developed to store materials which are sensitive to moisture, oxygen and other gases found in the environment. They are capable of ring 10-6 torr vacuum level, using appropriate vacuum pumps and maintaining a high degree of vacuum for years. Far superior to available desiccators or glove boxes, which are constructed of high outgassing materials and poor vacuum seal design. Constructed from stress relieved borosilicate glass (max heat 150 C) with a polished sealing surface. The lid is of low outgassing aluminum alloy with Viton Gasket and PTFE shaft sealed metal valve. 6088 Vacu-Storr Desiccator, 5" ID, 6 H, 6087 Vacu-Storr Desiccator, 3.53" ID, 5.9" H, 6086 Vacu-Storr Desiccator, 1.64" ID, 2.8" H, 9