Electronic Taps & Hands-Free Hardware for the ultimate in Safety & Hygiene

ELECTRONIC & HANDS-FREE TAPS Electronic Taps & Hands-Free Hardware for the ultimate in Safety & Hygiene SAVE WATER AND IMPROVE HYGIENE WITH INTELLIGENT DESIGN BENEFITS The Delabie range offers superior quality taps that focus on hygienic benefits through various hands-free options. Superior endurance, ergonomic design, total safety, hygiene and infection control along with water saving benefits to end users. Good hand-washing & water-saving habits can be encouraged with the right equipment, such as Delabie s hands-free products. Fit any Delabie hands-free product to a basin of your choice to create hands-free wash stations to promote hygiene and immediately enjoy all the benefits. Water Saving With Delabie electronic hands-free taps you could enjoy up to 90% water savings! - approx. 1300 pa. based on standard foodservice operations. Improve Hygiene Hands-free use significantly reduces cross-contamination and risk from germs and bacteria to improve health and safety. Beat Bacteria Build-Up With a smooth spout interior, low volume of standing water and an anti-bacterial duty flush. These taps are built to significantly reduce the risk of bacterial development. Call us on: +44 (0) 1908 261511 Send enquiries to: info@mechline.com Email orders to: orders@mechline.com www.mechline.com 77

HYGIENE AND LING BACTERIAL PROLIFERATION 90% WATER AND ENERGY SAVINGS Opens/closes automatically, with no manual contact DELABIE s electronic controls are operated by active infrared detection. Flow opens when the detector senses hands and shuts off automatically when hands are removed from the detection zone. No manual contact prevents the spread of germs by hand. Anti-bacterial duty flush programme If a mixer or tap is not used for prolonged periods of time (e.g. isolated points-of-use, facilities closed during holidays, etc.), water in the pipework is not renewed, which inevitably favours the development of bacteria. DELABIE s electronic controls have a duty flush programme. An automatic flush takes place for approximately 60 seconds every 24 hours after the last use (programmable on some models). Reduced-stagnation solenoid valve Most solenoid valves are fitted with a rubber membrane behind which water stagnates and is not renewed. This can lead to bacterial proliferation. DELABIE has developed a patented technology that operates without a membrane (patented system), supplied with the majority of electronic controls. With this piston-operated solenoid valve, water is drained and renewed with every use which reduces bacterial niches. The solenoid valves self-cleaning system with a calibrated groove reduces the build-up of dirt. Furthermore, its slow closure eliminates water-hammer. Hygienic flow straightener Unlike conventional aerators, DELABIE s flow straightener has a special Hostaform design, a material that is highly scale-resistant (build-up of scale is 10 times slower). It minimises water retention and the build-up of dirt, and prevents the spread of germs. Water savings Compared to conventional mixers and taps, DELABIE s electronic controls can offer maximum water savings. They ensure the manager s water bills can be reduced whilst preserving user comfort. Automatic shut-off and split delivery The mixer or tap shuts off automatically when hands are removed from the detection zone. This removes the risk of waste through negligence. The antiblocking security activates to prevent the mixer or tap from flowing continuously. The flow time is reduced to the necessary minimum (wetting, rinsing). Flow rate regulated at 3 lpm DELABIE s electronic mixers and taps are set at 3 lpm. The flow rate remains constant whatever the water pressure in the system. The flow rate is pre-set at 3 lpm at 3 bar. However, it can be adjusted from 1.5 to 6 lpm. Energy savings DELABIE s electronic mixers and taps (mains and battery-operated) do not require much energy to operate. DELABIE has chosen infrared active pulse technology, a low-power consumption solution. The infrared beam is emitted intermittently, saving energy while ensuring effective detection. DELABIE s battery-operated electronic models have an average life span of 350,000 cycles (i.e. 3 to 6 years) depending on the frequency of use. The Lithium batteries are widely available, affordable and recyclable. The significant hot water savings provided by DELABIE s mixers and taps also result in energy savings. Ecolabels The water and energy saving performance of DELABIE s electronic controls means that the buildings achieve the highest performance standards for international rating schemes such as LEED, BREEAM, HQE or ESTIDAMA. Hygiene and controlling bacterial proliferation Reduced-stagnation solenoid valve No manual contact Conventional mixer 9 lpm 0% DELABIE mixer 3 lpm 90% PEX flexible hoses These flexible hoses will withstand the thermal and chemical shocks undertaken in public facilities for preventative or curative treatments against the development of bacteria. Pathogen-free mixers and taps DELABIE guarantees that its mixers and taps will be delivered free from pathogenic bacteria. Flow rate Wetting Soaping Rinsing 9L 3L 5 sec. 20 sec. 7 sec. 5 sec. 7 sec. 4.8L 0.6L 32 sec. 12 sec. Water saving per use COMPARISONS OF WATER CONSUMPTION Comparison between a conventional mixer and a DELABIE electronic mixer Water consumption 4.8L 32 sec. 0.6L 12 sec. 78 NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts. No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.

SPECIFICALLY DESIGNED FOR COMMERCIAL ENVIRONMENTS Vandal-resistant Reinforced fixings Diagnostic LED Easy to maintain Resistant to intensive use and vandalism DELABIE s electronic controls have been specifically designed to withstand intensive use and vandalism, both voluntary and involuntary. The mixer and tap bodies are made from chrome-plated solid brass, fitted with shockproof mechanisms and sensors. Reinforced fixings will stand up to intensive use. Streamlined designs discourage attempts at vandalism. To prevent abuse and waste, all models are fitted with a system to avoid blocking during flow. For areas that require tamperproof installations, there are recessed and cross wall versions which have mechanisms that cannot be accessed by the user. Easy to install DELABIE's products are easy to install and adjustments are kept to a minimum in order to save time during installation. Independent electronic control unit, 230/12V mains or 6V Lithium batteries*: BINOPTIC, TEMPOMATIC 2 and PRO models Depending on the model, there is an option to adjust the presence detection distance, to change the operating mode (On/Off or automatic) and change the duty flush settings. The battery-operated models work autonomously for 3 to 6 years. The electronic control units are waterproof (IP65) with diagnostic LEDs to facilitate servicing. Electronic unit and solenoid valve integrated in the body of the mixer/tap*: TEMPOMATIC 3 and 4 models Can be installed on any isolated point-of-use, for new builds as well as renovation. - 6V Lithium battery*: There are no electrical connections required. Simply connect the flexibles to the supply pipes in the same way as for a conventional mixer/tap. No special adjustment is necessary, the mixer/tap is ready to operate independently for 3 to 6 years. A red LED will flash for 15 days to indicate that the battery life is low. The battery can be changed without shutting off the water supply or removing the mixer/tap. - 230/6V mains supply (plug in or recessed)*: Simply connect the flexibles to the supply pipes and connect the electrical supply to the mixer/tap via a plug and socket or recessed connection close to the basin. This does not require any specific maintenance (no battery changes). * Depending on model Reliable presence detection DELABIE has chosen the most reliable detection system: infrared active pulse. Under no circumstances will it change or be affected by variations in light levels. On models with a sensor at the end of the spout, the infrared beam adapts automatically, to ensure that the hands are detected in any position. Minimal servicing and easy to maintain The scale-resistant solutions (flow straighteners, mechanisms) and the filters ensure minimal servicing. The spare parts are standardised to ensure quick and easy replacement by the maintenance staff. The electronic control units are fitted with LEDs to aid diagnostic checks, and access to the components (battery, solenoid valve) is direct, without having to remove the mixer/tap. Technical characteristics Operating pressure Pressure differential CW / HW Electrical supply* Electronic unit* 6V Lithium battery* Duty flush programme can be adjusted* Automatic shut-off in event of negligence Temperature limiter HW supply Recommended installation height for wall-mounted taps/mixers * Depending on model 1-5 bar, 3 bar recommended P < 1 bar 230V / 50 Hz class II (without earth connection) Independent waterproof IP65 123 or 223 standard batteries Average life span ~350,000 cycles or 3-6 years Off or 60 sec. 12hr or 24hr after the last use Prevents blocking in the open position Can be adjusted 55 C max 110-200mm above base of bowl Conforms with European directives CEM 2014/30/UE and BT 2014/35/UE 10-year warranty against any manufacturing defects. DESIGN DELABIE s products, known for their endurance and reliability, have a timeless design. The diversity of the product range fits in perfectly with any commercial installation. In an office building or a shopping centre it is paramount that the product design fits in with its surroundings. Aesthetic products are subject to less vandalism as they are better respected. The smooth shape of the taps reduces the build-up of dirt and facilitates cleaning. Easy but secure access to the control mechanisms provides easy maintenance. Call us on: +44 (0) 1908 261511 Send enquiries to: info@mechline.com Email orders to: orders@mechline.com www.mechline.com 79

TEMPOMATIC 3 TEMPOMATIC 3 has the electronic control, solenoid valve and 6V Lithium battery integrated within the body of the tap. Can be installed on any isolated point-of-use: suitable for new builds as well as renovation. There is no need for electrical connections (saving installation time). Easy installation: flexibles are connected to the pipework in the same way as for traditional taps. There is no need for special adjustment, the tap is ready to operate autonomously for 3-6 years* (the average lifespan of the battery). Our electronic mixers and taps, both mains and battery-operated, incorporate an antibacterial duty flush to prevent water stagnation in the pipework. Anti-bacterial duty flush (battery-operated) Automatic duty flush (for ~60 seconds 24 hours after the last use): avoids water stagnation and the development of bacteria in the supply pipes. Electronic control with integrated battery Standard mode, without the option to change the operating mode: automatic shut-off when hands are removed from sensor field and safety shut-off after 30 seconds, in case the user forgets. Installation TEMPOMATIC 3 can be installed in the same way as traditional taps. Simply connect the flexibles, no other installation or adjustment is necessary. Optimised detection and ease of use The sensor is located at the end of the spout to ensure that hands are detected in any position. On the TEMPOMATIC 3, a diagram on the top cap ensures that the sensor is instantly identified. The new solenoid valve with piston (patented) for batteryoperated taps, limits bacterial development and avoids waterhammer when the valve closes: - self cleaning calibrated groove reduces the build-up of impurities and cleans the mechanism with every use. - the water is drained and renewed every time the valve operates, preventing any water stagnation. Changing the battery The sensor will flash for 15 days to indicate that the battery should be changed, after approximately 350,000 cycles. Changing the battery is easy (type 223), there is no need to remove the tap or isolate the water supply. Remove the top cap with an Allen key for direct access to the battery. Common characteristics of our electronic models Recommended pressure: 1.5 to 5 bar Minimum pressure: 1.5 bar Maximum pressure: 8 bar Basic flow rate: 0.05 lps at 3 bar Maximum hot water temperature: 70ºC Balance the CW and HW pressure ( P<1bar) If necessary, protect the installation with cartridge filters and pressure reducers. Waterproof control unit and electronic module Solenoid valves will not corrode Pre-set maximum temperature limiter. Maximum temperature limiter must be removed if a TMV is installed upstream Automatic shut-off in case of neglect, prevents continuous flow. Opens again when hands are detected in the sensor field. Electromagnetic compatibility in accordance with EU directive CEM 2004/108/CE and BT 2006/95/CE 80 NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts. No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.

DECK MOUNTED - ELECTRONIC & BATTERY-OPERATED S 460 90 110 125 135 405 90 125 405 110 135 445 DLB-478-015 DLB-478MCH DLB-378-015 DLB-378MCH BINOPTIC Mix / BINOPTIC - BATTERY operated models Deck-mounted electronic basin tap. - Independent IP65 electronic control unit. - 123 6V Lithium battery-operated. - 15mm connector for compression fittings. - Flow rate pre-set at 3 lpm at 3 bar, can be adjusted from 1.5 to 6 lpm. - Scale-resistant flow straightener. - Adjustable duty flush (pre-set flush ~60 sec. every 24hr after last use). - Active, infrared presence detection, sensor at the end of the spout DLB-478-015 DLB-478MCH Ø 15 optimises detection. - Chrome-plated brass body. - PEX flexible with filter and solenoid valve. - Reinforced fixing. - Anti-blocking safety. - Spout with smooth interior and low volume of water (reduces bacterial niches). - Side temperature control with adjustable maximum temperature limiter (478MCH15 model only). BINOPTIC sensor tap - BATTERY operated model BINOPTIC mixer tap - BATTERY operated model BINOPTIC Mix / BINOPTIC - MAINS supply models Deck-mounted electronic basin tap. - WRAS-approved - Independent IP65 electronic control unit. - 230/12V mains supply with transformer. - 15mm connector for compression fittings. - Flow rate pre-set at 3 lpm at 3 bar, can be adjusted from 1.5 to 6 lpm. - Scale-resistant flow straightener. - Adjustable duty flush (pre-set flush ~60 sec. every 24hr after last use). - Active, infrared presence detection, DLB-378-015 DLB-378MCH sensor at the end of the spout optimises detection. - Chrome-plated brass body. - PEX flexible with filter and solenoid valve. - Reinforced fixing. - Anti-blocking safety. - Spout with smooth interior and low volume of water (reduces bacterial niches). - Side temperature control with adjustable maximum temperature limiter (378MCH15 model only). BINOPTIC sensor tap - MAINS supply model BINOPTIC mixer tap - MAINS supply model 310 200 460 310 200 460 DLB-44200615 TEMPOMATIC Mix 3 / TEMPOMATIC 3 Electronic mixer or tap for washbasins with 6V Lithium battery, solenoid valve and electronic controls integrated in the body of the tap. Infra-red presence detection. - WRAS-approved - Flow straightener set at 3 lpm at 3 bar. Flow rate can be adjusted if the pressure < 3 bar. - PEX flexibles with integrated filters. DLB-44200615 DLB-49200615 DLB-49200615 - Chrome-plated brass body with reinforced fixings. - Anti-blocking safety & temp. limiter. - Duty flush (for ~60 seconds 24 hours after the last use). TEMPOMATIC 3, battery-operated tap (non mixer) - Mixer Valves can be fitted, if required. TEMPOMATIC Mix 3, battery-operated tap (mixer) TEMPOMATIC MIX PRO Electronic mixer for washbasins with removable swivel spouts L200 H310 and infra-red presence detection. - Flow straightener set at 3 lpm at 3 bar. Flow rate can be adjusted if pressure < 3 bar. - PEX flexibles with filters and solenoid valves M1/2. - Chrome-plated brass body with reinforced fixing. - Separate IP65 electronic control unit (with integrated transformer 230/12V). - Removable spout (for sterilisation in the medical sector). - Automatic duty flush (for ~60 seconds 24 hours after the last use). - Two shut-off modes available on 230/12V models: > Standard mode: timed flow with automatic shut-off. > ON/OFF mode: voluntary shut-off or after 30 minutes of flow. DLB-495-253 DLB-495-257 DLB-495-257 TEMPOMATIC MIX PRO - electronic basin mixer with swivel spout; mains power supply 230/12V w/transformer Same as 495 25315, but battery-operated (6V Lithium batteries) DLB-495-253 Call us on: +44 (0) 1908 261511 Send enquiries to: info@mechline.com Email orders to: orders@mechline.com www.mechline.com 81

PANEL MOUNTED - MAINS & BATTERY-OPERATED BASIN TAPS 180 190 max 135 BINOPTIC Cross wall electronic basin mixer. - Independent IP65 electronic control unit. - 230/12V mains supply with transformer. - Flow rate pre-set at 3 lpm at 3 bar, can be adjusted from 1.5 to 6 lpm. - Scale-resistant flow straightener. - Adjustable duty flush (pre-set flush ~60 sec. every 24hr after last use). - Active, infrared presence detection, sensor at the end of the spout optimises detection. - Filters and solenoid valves. - Chrome-plated brass body and spout. - Anti-blocking safety. - Spout with smooth interior and low volume of water (reduces bacterial niches). - Mixer valves can be fitted, if required. DLB-379-D13 DLB-379-DER DLB-379-ENC L 135mm spout for cross wall installation 190mm, 15mm connector for compression fittings as above with spout L 205mm L 200mm spout for recessed installation, M 3/8 fittings DLB-379-D13 Ø 15 DLB-379-ENC TEMPOMATIC 3 Wall-mounted electronic basin tap. - Battery-operated with integrated 223 6V Lithium battery. - Reduced-stagnation solenoid valve and electronic unit integrated into the body of the tap. - Flow rate pre-set at 3 lpm at 3 bar, can be adjusted from 1.5 to 6 lpm. - Scale-resistant flow straightener. - Duty flush (~60 sec. every 24hr after last use). - Active, infrared presence detection, sensor at the end of the spout optimises detection. - Chrome-plated solid brass body. - Cap fixed in place by 2 concealed screws,with pictogram to identify the sensor easily. - Wall-mounted, M1/2. - O 50mm, L. 190mm. - Anti-blocking safety. - 10-year warranty. DLB-443-006 Spout length 190mm HYGIENE LINE HANDS FREE CONTACT TEMPOGENOU - Knee-operated valves DLB-734-100 35 30 DLB-735-400 DLB-734-100 Angle type from the wall inlet DLB-735-400 Straight type in line inlet/outlet DLB-736-101 280 MONOFOOT - Pedal-operated valve DLB-736-101 Floor mounted 300 DLB-736-102 440 Ø 50 Ø 80 435 280 DLB-739-100 300 DLB-739-102 MIXFOOT - Pedal-operated mixer DLB-739-100 Floor mounted DLB-736-102 Wall mounted (height of pedal is adjustable) DLB-739-102 Wall mounted (height of pedal is adjustable) 82 NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts. No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.

PRE-MIXERS (MIXER VALVES) PREMIX COMPACT Thermostatic mixing valve for mixed water distribution between 30 and 60 C. - Adjustable temperature from 30-60 C, can be blocked by the installer. - Anti-scalding safety: immediate shut-off if cold water suppply fails. - Minimum flow rate required to operate: 5 lpm - Integrated non-return valves. Thermal shocks can be undertaken without special equipment. 140 PREMIX NANO Thermostatic mixing valve for mixed water distribution between 34 and 60 C. - For 1 to 2 tap or 1 shower. - Anti-scalding safety: immediate shut-off if cold water suppply fails. - Temperature pre-set at 38 C, can be adjusted by the installer from 34-60 C. - Integrated non-return valves and filters. - Minimum flow rate for operation: 3 lpm. - Thermal shocks are possible. - Buildcert Approval no. BC1430/0814. WRAS No. 1409058. 3/4" DLB-733-020 3/4" 40 3/4" 140 DLB-732-115 DLB-733-015 40 DLB-732-116 DLB-733-015 Thermostatic Mixing Valve - 1/2-inch DLB-732-115 Nickel-plated body M1/2, 15mm DLB-733-020 Thermostatic Mixing Valve - 3/4-inch DLB-732-116 Polished chrome body M1/2, 15mm COMPACT MIXER For individual washbasins, to be installed underneath the washbasin. - BSP(MF) with non-return valves and filters. - Nickel body. - Integrated stopcocks (function can be easily checked) and filters. DLB-200-000 NB: Water supplies to mixer valves - operating pressures to be between 1 and 5 bar. Supplies to be balanced. Max difference 1 bar. Manual Mixer - compact Nickel-plated, MF 1/2-inch with non-return valves & filters AN ECONOMICAL & ENVIRONMENTAL SOLUTION TO END OF LIFE FOOD WASTE CALL US TO FIND OUT HOW www.waste2-0.com Call us on: +44 (0) 1908 261511 Send enquiries to: info@mechline.com Email orders to: orders@mechline.com www.mechline.com 83

MAINTENANCE PARTS N H F G I Image DLB-729-308 Cartridge for deck mounted Soap Dispensers - s 729 008, 729 508, 729 108 DLB-729-312 Cartridge for deck mounted Soap Dispensers - 729 012 DLB-729-302 Seal Kit for Soap Dispensers DLB-753-736 F Maintenance Washer Bag for MONOFOOT DLB-753-739 F Maintenance Washer Bag for MIXFOOT DLB-495-626 G For TEMPOMATIC & BINOPTIC - Solenoid Valve, 230/12V DLB-495-646 H For TEMPOMATIC & BINOPTIC - Solenoid Valve, 6V DLB-492-646 N For TEMPOMATIC 3 BINOPTIC - Solenoid Valve, 6V DLB-495444 I For TEMPOMATIC & BINOPTIC - Standard Electronic Control Box DLB-495445 I For TEMPOMATIC & BINOPTIC - Multi-Function Electronic Control Box DLB-495446 I For TEMPOMATIC & BINOPTIC - 6V Battery Electronic Control Box DLB-492-446 P For TEMPOMATIC 3 models, electronic control box, 6V DLB-495-070 K For TEMPOMATIC & BINOPTIC - Tempomatic Sensor with Wire, 700mm DLB-495-149 K For TEMPOMATIC & BINOPTIC - Tempomatic Sensor with Wire, 1500mm DLB-495-499 K For TEMPOMATIC & BINOPTIC - Tempomatic Sensor with Wire, 5000mm DLB-990-223 Q For TEMPOMATIC 3 models, 6V Lithium batteries - (CR P2 6V battery) DLB-925-622.2P L Scale & Vandal Proof Flow Restrictors (Aerator) F22 DLB-925-624.2P L Scale & Vandal Proof Flow Restrictors (Aerator) M24 DLB-823-012 Non-Return Valve M 1/2-inch M 3/8-inch with filter TEMPO-CAP End cap for TEMPOMATIC 3 taps P Q L K WHY COMPROMISE ON GAS SAFETY FOR THE SAKE OF CUTTING COSTS YOUR REPUTATION IS OUR BUSINESS PAGES 115-122 84 NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts. No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.