Overview White Knight Rust Guard SLS Etch Primer is an etching primer with superior locking system for maximum rust protection. Ideal for priming aluminium, galvanised iron ZINCALUME, chrome, brass and copper objects to protect from corrosion. Features: Anti-corrosive Locks into metal Exceptional adhesion Fast drying Excellent base for topcoats Safe to spray - CFC and lead free Non chroming formula Suitable for use on fences, roofs, doors, gutters, pipes, windows, railings and gates Suitable Surfaces White Knight Rust Guard SLS Etch Primer may be applied to aluminium, galvanised iron, ZINCALUME, chrome, brass and copper.
Safety & First Aid KEEP OUT OF REACH OF CHILDREN. If swallowed, seek medical advice immediately and show the container or label. Do not induce vomiting. If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention. Avoid breathing vapour or mist. Use only with adequate ventilation. If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners. Warning - Misuse by concentrating and inhaling contents can be harmful or fatal. KEEP OUT OF REACH OF CHILDREN. This product is highly flammable. Store and use away from heat and eliminate any source of ignition. If swallowed seek medical advice immediately and show the container or label. Do not induce vomiting. If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention. If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners. Avpid breathing vapour or mist. Use only with adequate ventilation. For 24 hour medical emergency response in Australia call 1800 807 001 and in New Zealand call 0800 154 666 Caution HIGHLY FLAMMABLE. KEEP AWAY FROM FLAME AND ELIMINATE ANY SOURCE OF IGNITION. Keep in a cool place and out of sun. Contents under pressure. Do not puncture or incinerate this can, even when empty.
Environment Residual paint should be sprayed onto newspaper, allowed to dry and disposed of via domestic waste collections. Empty aerosol cans are recyclable via steel can recycling programs. Do not pour unwanted paint down the drain. Keep unwanted paint in sealed containers for disposal via special chemical waste collections. Empty paint containers should be left open in a well ventillated area to dry out. When dry, recycle steel containers via steel recycling programs. Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first. Preparation Remove all rust and flaking paint back to bare metal with a wire brush, scraper or mechanical sander. The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants. Cover all necessary areas to protect from overspray. Remove all rust and flaking paint back to bare metal with a wire brush, scraper or mechanical sander. The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants.
Application 1. Shake can vigorously for 1 minute before use and regularly during use. 2. Hold the can upright approximately 15-20 cm from the surface. 3. Press button firmly and spray with a smooth sweeping motion. Apply a prewetting mist coat followed by a full even coat, overlapping each spray pass. To prevent paint sagging, avoid spraying too close to the surface or spraying too heavily. 4. Repeat if necessary. Do not use when air or surface temperature is below 15 C or above 30 C. 1. Stir thoroughly with a broad flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application. 2. No thinning is required for application by brush or roller. If spraying with a spray gun, you may thin up to 10% with White Knight Rust Guard Solvent. 3. Apply 1 coat by brush, roller or spray gun. Do not use when air or surface temperature is below 10 C or above 30 C Overcoating Overcoat between 1 and 24 hours after application with an enamel or water based topcoat. Overcoat between 2 and 24 hours after application with an enamel or water based topcoat. Coverage Approximately 1.5m² per can Approximately 14m² per litre, depending on the nature of the surface.
Drying Touch dry in 10 minutes. Touch dry in 10 minutes. Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied. Clean Up To prevent nozzle blocking, after use turn can upside down and press button until only gas escapes. Overspray can be removed while still wet with White Knight Rust Guard Solvent or methylated spirits. Clean brushes and equipment with White Knight Rust Guard Solvent immediately after use.