Simple Fit Switching Sensors 1.8m to 3m Cone-shaped detection pattern, 6m radius at mounting height 6.0m AC220~240V/50Hz MK Simple Fit Sensors offer cost effective presence detection for lighting control in small to medium areas. This one-box solution is easy to install and coission, and requires no additional parts. Providing cost effective presence detection for lighting control. Simple Fit dual mount sensors are easy to install and can deliver energy savings of up to 70%* RECOMMENDED CIRCUIT PROTECTION 16A MAXIMUM LOAD 6A or 600W fluorescent lightling load capacity Approx. 5-1000 Lux OFF DELAY 5sec - 18min COLOUR White (RAL9010) MATERIAL/ABS Flame retardant PC Surface Mount: IP44 Flush Mount: IP44 (Sensor section only) IP20 (Ceiling Board onwards) K5017 DEPTH REQUIRED BEHIND CEILING 50 269g SWITCHABLE LOAD Max 2000W l Presence detection by passive infrared l Innovative dual mount system requires only one sensor for either flush or surface mount applications l External prograing dials enable quick adjustment of time and lux levels l Off delay adjustable between 5 seconds and 18 minutes following the last observed movement after which the lights switch off l Lens provides 360 degree detection l Detection Range of up to 6m diameter at 25 C at mounting height l Manual on / off override function l Mounting Height: Recoended ceiling mount 1.8m to 3m Dimensions () Flush Mount (Hole size 75 to 80) 68 l Loading up to 6 Amps l Ability to wire more than 1 sensor in parallel to a load l Ability to switch volt free loads l Lens mask included to mask out any areas of unwanted detection K5017 Flush and Surface Ceiling Mount Sensor in one l For flush mount, spring clips enable ease of installation in ceilings with thickness between 5 and 20 l Simple to switch between flush and surface options l Surface mount can be fixed direct to the ceiling or on to a circular conduit or BESA box l All screws and fixings supplied 97.18 Max 600W Max 500W 65.42 40.8 114.63 97.18 Max 120W Max 110W Surface Mount 21.95 56 56 Max 75W For a full range of corresponding products, see pages 63-66 in the product selector. 66.72 44.45 2.4 o 22.27 17.92 485
Simple Fit Switching Sensors mkelectric.co.uk 1.8m to 3m Cone-shaped detection pattern, 6m radius at mounting height AC220~240V/50Hz RECOMMENDED CIRCUIT PROTECTION 16A MAXIMUM LOAD 6A or 1500W fluorescent/incadescent lightling load capacity Approx. 30~200 Lux OFF DELAY 5sec - 40min COLOUR White MATERIAL Flame retardant PC IP20 K5015 DEPTH REQUIRED BEHIND CEILING 100 105g excluding cable K5016 105g approx 6.0m MK Simple Fit Sensors offer cost effective presence detection for lighting control in small to medium areas. These one-box solutions are easy to install and coission, also no additional parts are required. The following versions are available: l Flush mounted K5015 Spring Clips enable ease of installation in plasterboard ceilings l Surface Mounted K5016 Screw and Plug Fixings can be mounted direct to the ceiling or on to a square pattress box (K2160 WHI) 6m 0-40 Dimensions K5015 K5016 Advanced presence detection by passive infrared () technology Passive photocell holds lights off when area becomes occupied in bright ambient conditions Off delay in minutes following the last observed movement after which lights switch off Detection pattern and approx range in metres at floor level for mounting height (detection pattern is cone shaped). K5015 K5016 86 86 76 76 54.5 86 486
Superior Switching Sensors DETECTION 10m Macro / 7m at mounting height Aspect ratio Macro = 4:1 = 2.8:1 SWITCHING CAPACITY 10A (Tungsten 6A) 7m (LUX) Adjustable 10 to 1000 lux via K4098 1.5m 7m 1.5m K5030F K5030SM A range of high performance switching sensors for dependable switching of lighting loads. DELAY TIME Adjustable 5mins to 40 mins via K4098 IP4X SUPPLY VOLTAGE Mains 230V TEMPERATURE 0-40 degrees ACCESSORIES K4098 Infrared prograing tool required to adjust sensor settings l High definition lenses, performance optics and software are all optimised to provide class leading sensitivity and occupancy detection ensuring that the lights are always on when required l Superior switching sensors include integral adjustable active photocells which will hold the lights off in occupied areas or switch them off at a given light level l Superior switching sensors deliver highly sensitive micro detection diameter of 7m within a 10m macro detection diameter (When installed at a mounting height of ) l Colour coded connectors make superior switching sensors easy to install and reduce wiring faults l The easy to use K4098 infrared prograing tool simplifies sensor set up and coissioning Flush Mount 73 75 17.6 ø 87 Surface Mount ø 93 107.6 ø 87 487
Superior s for DALI or DSI Diing mkelectric.co.uk DETECTION 10m Macro / 7m at mounting height 7m Aspect ratio Macro = 4:1 = 2.8:1 K5040F K5040SM A range of high performance sensors for dependable control of digital diing lighting loads. 1.5m 7m 1.5m SWITCHING CAPACITY 10A (Tungsten 6A) DIGITAL DIMMING DALI or DSI (Auto detect) ANALOGUE DIMMING 1-10V (LUX) Adjustable 100 to 1000 lux via K4098 DELAY TIME Adjustable 5mins to 40mins via K4098 IP4X SUPPLY VOLTAGE Mains 230V TEMPERATURE 0-40 degrees ACCESSORIES K4098 Infrared prograing tool required to adjust sensor settings l High definition lenses, performance optics and software are all optimised to provide class leading sensitivity and occupancy detection ensuring that the lights are always on when required l Diing sensors include integral photocells which will hold the lights off in occupied areas or switch them off at a given light level. Regulating photocells enable a constant light level to be maintained through digital diing Flush Mount 73 l Superior sensors deliver highly sensitive micro detection diameter of 7m within a 10m macro detection diameter (When installed at a mounting height of ) l Automatic detection of DALI and DSI digital diing type luminaires reduces coissioning time and the potential for errors l The easy to use K4098 infrared prograing tool simplifies sensor set up and coissioning 75 17.6 ø 87 Surface Mount ø 93 107.6 ø 87 488
Battenfit Switching Sensor 5.0m Cone-shaped detection pattern, diameter (at floor level) = 2.4 x mounting height K4047 6.0m OFF DELAY 1 minute 40mins 10 second walk test mode Adjustable 50-5000 lux 230V 50Hz RECOMMENDED CIRCUIT PROTECTION 10 Amps Ideal for retrofit installations, the BattenFit sensor is a simple-to-fit control solution for batten style luminaires which can deliver energy savings of up to 70% 5-35 Advanced presence detection by passive infrared () technology Off delay in hours following the last observed movement after which lights switch off MAXIMUM LOAD 2A COLOUR White MATERIAL Flame retardant PC/ABS 100g IP65 ACCESSORIES K4098 Infrared prograing tool required to adjust sensor settings 5m IP A Passive photocell holds lights off in bright ambient conditions. Active photocell has the capability to switch lights off in occupied areas Detection pattern and range in meters under normal operating conditions One Switch Manual input to turn luminaires on or off Infrared prograing enables easy coissioning and re-coissioning via K4058 IP65 Dimensions () Detection Profile M20 x 1.5 14 29 Plan View o Detection pattern is a 360 cone shape. Diameter is 2.25 x the mounting height. The squares show the arrangement of the detection pattern. Sensitivity is greater when approaching at a tangent rather than heading towards the centre. BATTEN LUMINAIRE 14 40 107 5m Direction of most coonly used entry into detection zone, i.e. start of corridor or doorway o 97 DETECTION ZONE 5m 5.6m 102 600 489
Ultrasonic Sensors mkelectric.co.uk 230V 50Hz 5 metres SWITCH CAPACITY 10 Amps Incandescent lamps: 1500W max (230V) TERMINAL CAPACITY 2 x 1.5 or 1 x 2.5 Features K4030 K4031 148g TIME DELAY 5, 10 or 15 mins POWER-UP CONDITION select on or off DETECTOR adjustable ON/OFF S: adjustable 6m 5-15 13m Active presence detection by ultrasonic technology Passive photocell holds lights off in bright ambient conditions Off delay in minutes following the last observed movement after which the lights switch off Detection pattern and range in metres under normal operating conditions ULTRASONIC FREQUENCY 40kHz adjustable 50 to 5000 lux Ultrasonic sensors are general purpose, fully automatic, directional presence detectors with photocell. They save energy by switching off lights in unoccupied areas and by holding lights off in occupied areas which have adequate natural light. They use a specially developed ultrasonic radar to monitor the controlled space for movement. This radar is sensitive enough to respond to even very small movements thus ensuring that lights are sustained whenever the controlled space is occupied. If no movement has been detected for a pre-selected period, the sensors switch the lights off until the next visitor is detected. The sensors control feature a movement detector, photocell and 10 Amp load switching element in one easily deployed housing. The technology has been refined and improved over many years of efficient, reliable service in a wide range of industrial and coercial environments. The latest designs use state-ofthe-art miniaturisation to pack the features into a small, attractive yet rugged enclosure which gives full field-of-view adjustment. Detectors are available for surface or semi-flush mounting. Dimensions K4030 Surface version The back-box can be secured directly to a hard surface or to a conduit stop end box. 71 60 20 back entry knockout Rear View 3 x side entry knockout 83 60 51 K4030 Semi Flush version Use a hole saw to drill a 76 hole into the ceiling tile. The flush ring is designed to clamp the tile between its two halves. Flush Plate & Clamp (K4078) For simple flush mounting of detector to suspended ceilings. Max clamping distance 25 120 A sensor will fit to its own backplate or to a standard 25 switch sinking box. Ultrasonic sensors utilise ultrasonic radar to monitor a space for movement. This involves transmitting an ultrasound signal and examining the reflected signal for frequency variations called doppler shifts. The transmitted signal is more quickly dissipated in open space and squeezed out by constraining walls and ceilings. The range of the detector also depends upon the type of movement being observed: for example, walking activity can be observed at a greater distance than the slight hand or body movement to be expected from a person working at a desk. Note that detectors can see behind themselves slightly so must be inset in a storage aisle or corridor application. 490
Hand-Held Prograing Tools TRANSMISSION METHOD Infrared 15m approx BATTERY 3Vdc CR2032 Lithium Button Cell EXPECTED BATTERY LIFE 3 years STORAGE TEMPERATURE -25 C to +70 C OPERATING TEMPERATURE 0 C to 40 C K4058 K4059 4X APPROVAL CE DIMENSIONS K4058:87 (H) x 40 (W) x 7 (D) K4059:100 (H) x 50 (W) x 7 (D) MK sensors* feature a range of prograable parameters which can be adjusted using a simple, low cost hand-held prograing controller. *Not including Simple fit 20g approx K4058 l 3 simple time-delay settings (5 minutes/10 minutes/20 minutes) l Presence detection mode l Absence detection mode l Enable/disable photocell l Walk-test feature K4059 l 4 simple time-delay settings (5 minutes/10 minutes/20 minutes/40 minutes) l Presence detection mode l Absence detection mode l Enable/disable photocell l Walk-test feature l Set regulating light level - when used in conjunction with a suitable lux meter l Restore button functionality - press & hold reverts to factory default, short press reverts back to last configuration l Lamp burn-in 491