Grant Product Guide 05 Issue one
Grant profile At Grant we have been designing and manufacturing reliable and easy to install heating products for over 35 years. From award winning oilfired condensing boilers to the latest renewable technologies, our heating systems have a reputation for quality that is second to none. We combine precision engineering, innovation, performance and value for money to produce sustainable heating solutions that are trusted by both installers and householders.
Contents Oil Fired Boilers Oil Fired Boilers 4- Vortex Eco 4 Vortex Pro Indoor & Outdoor 5 Vortex Pro Combi & Boiler House 6 Vortex Mag-One Filter 7 EZ-Fit Flue systems 8-3 Air Source Heat Pumps 4-5 Aerona ASHE Range 4-5 Cylinders & Thermal Stores 6-3 MonoWave heat pump cylinders 6-7 DuoWave heat pump cylinders 6-7 DuoWave solar cylinders 8-9 DuoWave Plus cylinders 0 ThermaWave thermal stores -3 Solar Thermal 4-9 On roof kits 6 In roof kits 7-8 Flat roof kits 8 Accessories 9 Biomass 30-37 Spira wood pellet boilers 30-33 Vecta wood pellet boilers 34-35 Wood pellet stores 36 SpiraVAC vacuum systems 37 Energy Management Controls 38-4 Controllers 38 Low loss headers 39-40 Zone pump kits 4 Training Academy 4-43 Grant Training academy 4-43 +44 (0)380 73690 www.grantuk.com 3
Grant Vortex Eco Range Condensing Oil Fired Boilers Stainless steel heat exchanger SAP 009 seasonal efficiencies of 90.3% - 9.6% Exceptionally quiet operation Multidirectional flue options Simplified casing, control panel and pipework arrangement *System models only Product Output Dimensions Weight Code Btu/h KW H W D (KG) Burner Internal standard models - white cased VTXECO5 50-70 5-860 430 605 97 RDB. VTXECO6 70-90 -6 860 430 605 97 RDB. VTXECO635 90-0 6-35 900 470 603 7 RDB. Internal sealed system models - white cased VTXSECO5 50-70 5-860 430 605 TBC RDB. VTXSECO6 70-90 -6 860 430 605 TBC RDB. VTXSECO635 90-0 6-35 900 470 603 TBC RDB. External standard modules (inc flue) - powder coated case VTXOMECO5 50-70 5-908 505 005* 3 RDB. VTXOMECO6 70-90 -6 908 505 005* 3 RDB. VTXOMECO635 90-0 6-35 908 505 005* 4 RDB. External sealed system models (inc flue) - powder coated cased VTXSOMECO5 50-70 5-908 505 005* TBC RDB. VTXSOMECO6 70-90 -6 908 505 005* TBC RDB. VTXSOMECO6 90-0 6-35 908 505 005* TBC RDB. Wall hung internal standard models - white cased VTXWH6 40-55 -6 850 580 3 86 MAX VTXWH6 55-70 6-850 580 3 86 MAX Wall hung internal sealed system models - white cased VTXSWH6 40-55 -6 850 580 3 98 MAX VTXSWH6 55-70 6-850 580 3 98 MAX Wall hung external standard models - powder coated cased VTXOMWH6 40-55 -6 837 635 366 93 MAX VTXOMWH6 55-70 6-837 635 366 93 MAX Wall hung external sealed system models - powder coated cased VTXSOMWH6 40-55 -6 837 635 366 97 MAX VTXSOMWH6 55-70 6-837 635 366 97 MAX *Depth of boiler includes flue terminal & guard Accessories & Control Options Description ESKIT Wall-Mounted Twin Channel Programmer RSKIT Wall-Mounted Programmable Room Thermostat 4
Grant Vortex Pro Range Condensing Oil Fired Boilers Award winning range Stainless steel heat exchanger SAP 009 seasonal efficiencies of 90.7% - 93.3% Exceptionally quiet operation Multidirectional flue options Latest Riello burner technology *System models only Product Output Dimensions Weight Code Btu/h KW H W D (KG) Burner Internal standard models - white cased VTX5 50-70 5-855 348 566 97 RDB. VTX56 50-90 5-6 860 470 603 30 RDB VTX636 90-3 6-36 900 470 603 44 RDB VTX3646 3-57 36-46 900 470 603 44 RDB. VTX4658 57-00 46-58 34 563 786 68 RDB3. VTX5870 00-40 58-70 34 563 786 8 RDB3. Internal sealed system models - white cased VTXS56 50-90 5-6 860 470 603 38 RDB VTXS636 90-3 6-36 900 470 603 67 RDB VTXS3646 3-57 36-46 900 470 603 64 RDB. External standard modules (inc flue) - powder coated case VTXOM5 50-70 5-879 385 943* 09 RDB. VTXOM56 50-90 5-6 908 505 005* 43 RDB VTXOM636 90-3 6-36 908 505 005* 6 RDB VTXOM3646 3-57 36-46 908 505 005* 6 RDB. VTXOM4658 57-00 46-58 40 587 54* 74 RDB3. VTXOM5870 00-40 58-70 40 587 54* 88 RDB3. *Depth of boiler includes flue terminal & guard Accessories & Control Options VTXOMSSKIT VTXOMSSKIT6 VTXOMSSKIT46 MTKIT ESKIT EPKIT RSKIT RFTKIT Description 0 Litre Sealed System Kit for VTXOM5 Litre Sealed System Kit for VTXOM56 6 Litre Sealed System Kit for VTXOM636/ VTXOM3646 Internal 4hr Single Channel Mechanical Timer Kit 7 Day, Twin Channel Wall-Mounted Programmer 7 Day, Twin Channel Plug-In Programmer (for internal models) Wall-Mounted Programmable Room Thermostat Wireless, Twin Channle Programmable Room Thermostat +44 (0)380 73690 www.grantuk.com 5
Grant Vortex Pro Range Condensing Oil Fired Boilers Award winning range Stainless steel heat exchanger SAP 009 seasonal efficiencies of 90.7% - 93.3% Exceptionally quiet operation Multidirectional flue options Latest Riello burner technology *Combi models only Product Output Dimensions Weight Code Btu/h KW H W D (KG) Burner Internal standard models - blue cased VTXBH636 90-3 6-36 705 460 600 RDB VTXBH3646 3-57 36-46 705 460 600 RDB. VTXBH4658 57-00 46-58 0 540 868 RDB3. VTXBH5870 00-40 58-70 0 540 868 36 RDB3. Internal Combi models - white cased VTXCOMBI 70 860 64 609 60 RDB. VTXCOMBI6 90 6 860 64 609 77 RDB VTXCOMBI36 3 36 900 65 609 00 RDB. External Combi modules (incl flue) - powder coated cased VTXOMCOMBI 70 945 658 966* 8 RDB. VTXOMCOMBI6 90 6 945 658 966* 06 RDB VTXOMCOMBI36 3 36 945 658 966* 5 RDB. *Depth of boiler includes flue terminal & guard Combi Models Control Options MTKIT ESKIT EPKIT RSKIT RFTKIT Description Internal 4hr Single Channel Mechanical Timer Kit 7 Day, Twin Channel Wall-Mounted Programmer 7 Day, Twin Channel Plug-In Programmer (for internal models) Wall-Mounted Programmable Room Thermostat Wireless, Twin Channle Programmable Room Thermostat Boiler House Models Control Options ESKIT RSKIT Description 7 Day, Twin Channel Wall-Mounted Programmer Wall-Mounted Programmable Room Thermostat 6
MagOne Magnetic Filter High performance heavy duty filter Easy clean, easy drain design 000 gauss neodymium magnet Full bore flat face 8mm isolation valves with 8-mm reducers 0 C max working temperature 6 bar max working pressure 500ml dosing capacity Manual air bleed 360 o Installation Compatible with all system inhibitors & glycol solutions Suitable for systems up to 36kW, larger systems use two in parallel circuit VM0 Description Vortex MagOne universal /8mm magnetic central heating filter Note: Please allow enough clearance around the MagOne to ensure the isolating valves can be fully closed. It is recommended that a clearance of at least 50mm is given to enable the magnet and filter to be removed during servicing. Sufficient clearance must also be given to ensure that the MagOne can be drained easily into a suitable container. +44 (0)380 73690 www.grantuk.com 7
EZ-Fit Flue Systems Yellow System - Low Level balanced flue kits Low level Stainless steel Balanced Suitable for all internal Vortex models Easy to install Plume diverter kits available Output (kw) Description EZ90-6 Standard flue kit Walls up to 450mm (includes s/s terminal guard) EZ90S -6 Short flue kit Single skin walls up to 30mm (includes s/s terminal guard) X90S -6 Extension 5mm X90M -6 Extension 450mm X90L -6 Extension 675mm EZELB90-6 EZ45/90-6 90 Elbow Kit (Includes 90 elbow and 5mm Extension) 45 Elbow Kit (Includes 45 elbow and 5mm Extension) EZ45/90S -6 Short elbow only up to 6kW EZ00 6-70 Standard flue kit Walls up to 450mm (includes s/s terminal guard) EZ00S 6-70 Short flue kit Single skin walls up to 30mm (includes s/s terminal guard) X00S 6-70 Extension 5mm X00M 6-70 Extension 450mm X00L 6-70 Extension 675mm EZELB00 6-70 90 Elbow Kit (Includes 90 elbow and 5mm Extension) EZ45/00 6-70 45 Elbow Kit (Includes 45 elbow and 5mm Extension) EZ45/00S 6-70 Short elbow only above 6kW GPDA90-6 Adjustable plume diverter kit 80mm x metres GPD50EXT/90-6 Extension 50mm GPD500EXT/90-6 Extension 500mm GPD000EXT/90-6 Extension 000mm GPDA45/90-6 45 elbow GPDBRKT90-6 Wall bracket GPDA00 6-70 Adjustable plume diverter kit 00mm x metres GPD50EXT/00 6-70 Extension 50mm GPD500EXT/00 6-70 Extension 500mm GPD000EXT/00 6-70 Extension 000mm GPDA45/00 6-70 45 elbow GPDBRKT00 6-70 Wall bracket 8
White System - High Level/ Vertical balanced flue kits High level/ Vertical Stainless steel white powder coated Balanced Suitable for all internal Vortex models Easy to install Output (kw) Description HLK05090-6. metre High level adjustable flue kit c/w 90 elbow and terminal VTK055090-6 Adjustable Vertical 3 metre flue kit c/w terminal and storm collar EXTK35/90-6 Extension 5mm (9 ) EXTK09450/90-6 Extension 450mm (8 ) EXTK950/90-6 Extension 950mm (38 ) EXTK3ADJ/90-6 Adjustable extension 75-450mm (0 to 8 ) ELBK45/90-6 45 elbow VTMF90/00-70 Pitched master flashing [aluminium] VTK5P90-6 Pitched flashing [lead] VTK7F90-6 Flat flashing BRK990-6 Wall bracket VTTEXT90-6 Black extension for vertical terminal 80mm x mtr HLK09000 6-70. metre High level adjustable flue kit c/w 90 elbow and terminal VTK069000 6-70 Adjustable Vertical 3 metre flue kit c/w terminal and storm collar EXTK35/00 6-70 Extension 5mm (9 ) EXTK0450/00 6-70 Extension 450mm (8 ) EXTK950/00 6-70 Extension 950mm (38 ) EXTK4ADJ/00 6-70 Adjustable extension 75-450mm (0 to 8 ) ELBK45/00 6-70 45 elbow VTMF90/00-70 Pitched master flashing [aluminium] VTK6P40 6-70 Pitched flashing [lead] VTK6P00X 6-70 Pitched flashing [lead replacement, incl collar] VTK 8F00 6-70 Flat flashing BRK3000 6-70 Wall bracket VTTEXT00 6-70 Black extension for vertical terminal 00mm x mtr NOTE: High level/vertical flues, extensions and accessories can be used with all internal boilers. Vertical flue kits can be extended to a maximum straight length of metres. Deduct metre for each 45 elbow (max 6 elbows). High level flue kits can be extended to a maximum length of 0 metres. Deduct metre for each 45 elbow (max 6 elbows). For information on Plume Diverter Kits for high level flues, please contact our Technical Department +44 (0)380 73690 www.grantuk.com 9
Green System - External High Level/ Vertical balanced flue kits High level/ Vertical Stainless steel Balanced Twin wall insulated vertical extensions Suitable for all internal and external Vortex models Easy to install Output (kw) Description GK90-6 Standard Starter Kit (Stainless Steel) GK90S -6 Short Starter Kit (Stainless Steel) GKM90-6 Outdoor Module Starter (Elbow) + Test point GKM90C -6 Outdoor Module Starter (Straight) + Test point GX50/90-6 Extension 50mm GX50/90-6 Extension 50mm GX450/90-6 Extension 450mm GX950/90-6 Extension 950mm GXA50/90-6 Adjustable Extension 95-70mm GE45/90-6 45 Elbow GTL90-6 Straight Terminal Only GTH90-6 High level 90 Terminal GTV90-6 Vertical Terminal GWB90-6 Wall Bracket GEB90-6 Extended Wall Bracket GK00 6-70* Standard Starter Kit (Stainless Steel) GK00S 6-70* Short Starter Kit (Stainless Steel) GKM00 6-46* Outdoor Module Starter (Elbow) + Test point GKM00C 6-46* Outdoor Module Starter (Straight) + Test point GX50/00 6-70* Extension 50mm GX50/00 6-70* Extension 50mm GX450/00 6-70* Extension 450mm GX950/00 6-70* Extension 950mm GXA50/00 6-70* Adjustable Extension 95-70mm GE45/00 6-70* 45 Elbow GTL00 6-70* Straight Terminal Only GTH00 6-70* High level 90 Terminal GTV00 6-70* Vertical Terminal GWB00 6-70* Wall Bracket GEB00 6-70* Extended Wall Bracket CFA5/70-70 CF Adaptor/Connector from Orange to Green System NOTE: *The Grant Eco Outdoor Module - VTXOMECO635 uses the smaller -6 flue pipe. Please use extensions from the Yellow System to extend starter kits horizontally. The CFA5/70 is to only be used with the Grant Green and Orange Flue System. Fitting with any other flue system could invalidate the warranty of the boiler. If the CFA5/70 is not sent with components of the Green or Orange Systems, then full installation details will be required prior to despatch. 0
Orange System - Conventional flue kits Conventional flexi kits Smooth bore stainless steel liner White powder coated extensions Suitable for all internal Vortex models Available as complete kits Output (kw) Description GFKIT6/00-46 Flexi Kit 00mm dia x 6m GFKIT8/00-46 Flexi Kit 00mm dia x 8m GFKIT0/00-46 Flexi Kit 00mm dia x 0m GFKIT/00-46 Flexi Kit 00mm dia x m GFKIT/00-46 Flexi Kit 00mm dia x m GFKIT4/00-46 Flexi Kit 00mm dia x 4m GFKIT6/00-46 Flexi Kit 00mm dia x 6m WX50/00-46 White Extension 50mm x 00mm dia WX50/00-46 White Extension 50mm x 00mm dia WX450/00-46 White Extension 450mm x 00mm dia WX950/00-46 White Extension 950mm x 00mm dia WXA50/00-46 35mm x 300mm White Adjustable Extension x 00mm dia WE45/00-46 White 45 Elbow x 00mm dia GFKIT6/5 46-70 Flexi Kit 5mm dia x 6m GFKIT8/5 46-70 Flexi Kit 5mm dia x 8m GFKIT0/5 46-70 Flexi Kit 5mm dia x 0m GFKIT/5 46-70 Flexi Kit 5mm dia x m GFKIT/5 46-70 Flexi Kit 5mm dia x m GFKIT4/5 46-70 Flexi Kit 5mm dia x 4m GFKIT6/5 46-70 Flexi Kit 5mm dia x 6m WX50/5 46-70 White Extension 50mm x 5mm dia WX50/5 46-70 White Extension 50mm x 5mm dia WX450/5 46-70 White Extension 450mm x 5mm dia WX950/5 46-70 White Extension 950mm x 5mm dia WXA50/5 46-70 35mm x 300mm White Adustable Extension 5mm dia WE45/5 46-70 White 45 Elbow x 5mm dia Flexi Kit includes: Terminal/top plate/flexi-flue adaptor assembly, adaptor to flexi, boiler flue connector, locking band and fixing screws, plus tube of silicon and length of smooth bore insulated flexible flue liner. NOTE: Maximum vertical height from top of the boiler to the terminal is 9 metres. Maximum of x 45 elbows can be used. +44 (0)380 73690 www.grantuk.com
Red System - Flexi Vertical balanced flue kits Balanced flexi kits Suitable for all internal Vortex models up to 6kW Smooth bore stainless steel inner liner Available as complete kits Stainless Steel outer liner Output (kw) Description GFX BF6/6COMR -6 6m Balanced Flexi Liner Kit GFXBF8/6COMR -6 8m Balanced Flexi Liner Kit GFXBF0/6COMR -6 0m Balanced Flexi Liner Kit GFXBF/6COMR -6 m Balanced Flexi Liner Kit EXTK35/90-6 Extension 5mm (9 ) EXTK09450/90-6 Extension 450mm (8 ) EXTK950/90-6 Extension 950mm (38 ) EXTK3ADJ/90-6 Adjustable extension 75-450mm (0 to 8 ) ELBK45/90-6 45 elbow Liner Kit includes: 5mm flexi liner, 80mm 36 stainless steel smooth bore flexi liner, Boiler Connector, Telescopic Extension, Rigid to Flexi Adaptor and Terminal Assembly (approximate height above boiler case 80-0mm) NOTE: Maximum vertical height from top of the boiler to the terminal is 0mtrs. Deduct mtr for each 45 elbow (max 4 elbows). EZ CONVENTIONAL FLUE DESIGN SERVICE Individually designed conventional flue systems for modular boiler installations. Grant UK offers a unique customised design service, where two or more boilers are connected in a modular form to a single conventional flue stack. This service includes the design and supply of flue headers and flue systems for condensing boiler installations and is available to merchants upon completion of a simple site survey form. Contact our technical department on: +44 (0)380 73690 for further details.
Ref Position mm A Below a gutter or sanitary pipework * 600 B Horizontally from a door 600 C Above ground or balcony level 300 D Below eaves or balcony (without protection) * 600 E From internal corner ** 300 F From a terminal facing a terminal 00 G From a surface facing a terminal 600 H Vertical from terminals on the same wall 500 I Horizontal from terminals on the same wall *** 750 J Below an opening, airbrick, window etc. 600 K From vertical sanitary pipework 300 L Vertical flue from wall 750 M From oil tank 800 N Minimum height from the ground 000 O From external corner 300 P From Velux windows from sides & top 600 from below 000 Note: *75mm with protection **600mm for Outdoor modules ***Only applies if one or both terminals are balanced flues. Distance measured to rim of terminal. Clearances advised by Grant Engineering (UK) Ltd. in accordance with British Standards and Building Regulations. The terminal should be positioned so as to avoid products of combustion accumulating in stagnant pockets around the building or entering into buildings. Care should also be taken that the plume from a condensing flue does not cause a nuisance.. An opening means an openable element, such as a window, or a permanent opening such as a permanently open air vent.. Not withstanding the dimensions given, a terminal should be at least 300mm from combustible material e.g. a window frame. 3. A way of providing protection of combustible material would be to fit a heat shield at least 750mm wide. 4. Where possible it is always advisable to choose a High Level or Vertical flue option with condensing boilers to avoid nuisance pluming. +44 (0)380 73690 www.grantuk.com 3
ASHE75 Grant Aerona Air to Water Heat Pump Range High COP s sustainable at lower temperatures MCS approved R40a refrigerant Built in 3kW electrical backup Adjustable feet All models are single phase Weather compensating control Base tray heating element Simple plumbing and electrical connections Performance Data ASHE65 Output kw 6.7 5. 4.3 COP 4. 3.4.8 ASHE85 Output kw 8.7 7. 6. COP 4.3 3.3 3. ASHE5 Output kw.3 9.6 8.4 COP 4.0 3.3.8 ASHE75 Output kw 7.8 3.7.7 COP 4.0 3..8 ASHE5 Output kw. 7.9 6. COP 3.9 3.3.8 * Tested to BSEN45 Note: When selecting an Air Source heat pump, ensure output is matched with the correct system design temperature (varies by location) 4
Grant Aerona ASHE Heat Pumps ASHE65 ASHE85 ASHE5 ASHE75 ASHE5 Output (kw) 6.5 8.5.5 7.5.5 Height (mm) 077 378 378 58 45 Width (mm) 0 0 0 0 537 Depth (mm) 47 47 47 699 699 Weight (kg) Empty Full 6 9 45 48 73 76 33 38 334 339 Water proof level IPX4 IPX4 IPX4 IPX4 IPX4 Refrigerant R40a R40a R40a R40a R40a Operating voltage (v) Flow/return tappings (BSPF) Integrated heating element (kw) Min/max operating temperatures Air ( C) Max flow temperatures Water ( C) 30 ( phase) 30 ( phase) 30 ( phase) 30 ( phase) 3/4" 3/4" " " " 3 3 3 3 3 30 ( phase) -0 to +30-0 to +30-0 to +30-0 to +30-0 to +30 60 60 60 60 60 Compressor Rotary Rotary Scroll x Rotary x Scroll Base tray trace element Yes Yes Yes Yes Yes Sound power level at 6.5 6.8 64 68.5 63 metre (db(a)) * Sound pressure level at metre (db(a)) * 47.7 48 49 53 48.5 Starting current (A) (rms) 6 6 45 8/37 50/60 Nominal running current (A)** 7. 9. 3.3 0.3/0.5.3/4.4 * In accordance with BSENISO3744:995 ** Not including 3kW heater Grant Aerona Accessories HPDHWBK HPDHWBK Automatic domestic hot water boost kit (not timed) Automatic domestic hot water boost kit (timed) Grant Aerona Sealed System Kits HPAWSSK HPAWSSK8 HPAWSSK50 Litre sealed system kit for Aerona ASHP 8 Litre sealed system kit for Aerona ASHP 50 Litre sealed system kit for Aerona ASHP +44 (0)380 73690 www.grantuk.com 5
Wave Cylinder Range Duplex stainless steel mm and 8mm compression fittings No anode required Immersion heater Labelled colour-coded tappings All models are single phase Global warming potential (GWP) = less than 3 Ozone depletion potential (ODP) = 0 Grant MonoWave Heat Pump Cylinders Unvented indirect single coil duplex stainless steel HPMONO/ IND5 HPMONO/ IND50 HPMONO/ IND70 HPMONO/ IND00 HPMONO/ IND50 HPMONO/ IND300 HPMONO/ IND400 Capacity (ltrs) 5 50 70 00 50 300 400 Pressure regulator (bar) 3 3 3 3 3 3 3 Immersion (kw) 3 3 3 3 3 3 * 3 * Expansion vessel (ltrs) 9 9 4 4 35 Coil rating primary (kw) 4.0 7.0 7.0 47.0 47.0 56.6 56.6 Standing heat loss (kw/4hrs).86.80.48.54.83.08.08 Height (mm) 800 890 075 30 480 745 0 Diameter (mm) 580 580 580 580 580 580 580 Weight empty (kg) 30 3 45 49 59 68 76 Weight full (kg) 55 8 5 49 309 368 476 * x 3kW immersion heaters Grant DuoWave Heat Pump Cylinders Unvented indirect twin coil duplex stainless steel HPDUO/ IND70 HPDUO/ IND00 HPDUO/ IND50 HPDUO/ IND300 HPDUO/ IND400 Capacity (ltrs) 70 00 50 300 400 Pressure regulator (bar) 3 3 3 3 3 Immersion (kw) 3 3 3 3 3 Expansion vessel (ltrs) 9 9 4 4 35 Coil rating primary (kw) 3.0 47.0 47.0 55.6 55.6 Solar (kw) 8.5 0 6 6 3 Standing heat loss (kw/4hrs).48.54.83.08.08 Height (mm) 075 30 480 745 0 Diameter (mm) 580 580 580 580 580 Weight empty (kg) 57 6 7 80 00 Weight full (kg) 7 6 3 380 500 6
Grant MonoWave HP connections A Hot out B T+P valve C Secondary return D Heat pump flow E Heat pump return F Thermostat pocket G Immersion heater H Cold In I Immersion heater (300 & 400ltr models only) MonoWave HP 5ltr, 50ltr, 70ltr, 00ltr & 50ltr models B E H F D C G MonoWave HP 300ltr & 400ltr models B H E F D C I G Grant DuoWave HP connections A Hot out B T+P valve C Heat pump flow D Heat pump return E Secondary return F Thermostat pocket (top) G Immersion heater H Thermostat pocket (bottom) I Solar flow J Cold in K Solar return A A E B C D B C D DuoWave HP 70ltr model G J K I F H DuoWave HP 00ltr, 50ltr, 300ltr & 400ltr models E G J K I F H +44 (0)380 73690 www.grantuk.com 7
Grant DuoWave Solar Cylinders Unvented direct solar single coil duplex stainless steel GDUO/ DIR70 GDUO/ DIR00 GDUO/ DIR50 GDUO/ DIR300 GDUO/ DIR400 Capacity (ltrs) 70 00 50 300 400 Pressure regulator (bar) 3 3 3 3 3 Immersion (kw) 3 3 3 3 3 Expansion vessel (ltrs) 9 9 4 4 35 Coil rating primary (kw) 8.5 0.0 6.0 6.0 4.0 Standing heat loss (kw/4hrs).39.56.86.6.45 Height (mm) 075 30 480 745 0 Diameter (mm) 580 580 580 580 580 Weight empty (kg) 37 4 47 53 65 Weight full (kg) 07 4 97 353 465 Grant DuoWave Solar Cylinders Unvented direct solar single coil duplex stainless steel GDUO/ IND70 GDUO. IND00 GDUO/ IND50 GDUO/ IND300 GDUO/ IND400 GDUO/ IND500 Capacity (ltrs) 70 00 50 300 400 500 Pressure regulator (bar) Expansion vessel (ltrs) Coil rating primary (kw) 3 3 3 3 3 3 9 9 4 4 35 50 8.5 8.5 8.5 8.5 0.0 6.0 Solar (kw) 8.5 0.0 3.9 6.0 4.0 7.0 Standing heat loss (kw/4hrs).38.54.70.09.38 3.08 Height (mm) 075 30 480 745 0 835 Diameter (mm) 580 580 580 580 580 660 Weight empty (kg) 49 53 63 7 9 08 Weight full (kg) 9 53 33 37 49 608 8
Grant DuoWave connections A Hot out B T+P valve C Primary return (indirect only) D Secondary return E Top thermostat pocket (indirect only) F Primary flow (indirect only) G Solar return H Immersion heater (direct models only) I Thermostat pocket (bottom) J Cold mains in K Solar flow L Immersion heater Solar DuoWave A A B D B D C L F E G L DuoWave Direct models J K I H DuoWave Indirect models J G K I +44 (0)380 73690 www.grantuk.com 9
Grant DuoWave Plus Solar Cylinders Open vented indirect solar triple coil duplex stainless steel GDUO/PLUS300 Capacity (ltrs) 300 Coil rating primary (kw).6 Coil rating secondary (kw) 8.5 Solar (kw) 6 Standing heat loss (kw/4hrs).4 Height (mm) 745 Diameter (mm) 580 Weight empty (kg) 57 Weight full (kg) 357 Grant DuoWave Plus Solar Cylinders Unvented indirect solar triple coil duplex stainless steel GDUO/PLUS300U Capacity (ltrs) 300 Pressure regulator (bar) 3 Expansion vessel (ltrs) 4 Coil rating primary (kw).6 Coil rating secondary (kw) 8.5 Solar (kw) 6 Standing heat loss (kw/4hrs).4 Height (mm) 745 Diameter (mm) 580 Weight empty (kg) 57 Weight full (kg) 357 A Grant DuoWave Plus connections DuoWave Direct models DuoWave Plus Open Vented/Unvented models B C M L D H E G J I F K A B C D E F G H I J K L M Hot out T+P valve Secondary return Primary return Solid fuel flow Thermostat pocket (top) Solid fuel return Primary flow Solar return Solar flow Thermostat pocket (bottom) Cold mains in Immersion heater 0
Grant ThermaWave Stores Open vented duplex stainless steel thermal stores GTHERM/50 GTHERM/300 GTHERM400 Capacity (ltrs) 50 300 400 Coil rating solar (kw) 6 6 4 Standing heat loss (k/4hrs).69.7.94 Height (mm) 485 735 0 Diameter (mm) 580 580 580 Weight empty (kg) 55 6 74 DHW Sealed system duplex stainless steel thermal stores c/w hot water coil GTHERM300HWU GTHERM400HWU GTHERM500HWU Capacity (ltrs) 300 400 500 Coil rating solar (kw) 6 7.6 7.6 Coil rating DHW (kw) 46.4 55. 55. Standing heat loss (k/w4hrs).64.83.98 Height (mm) 650 590 835 Diameter (mm) 555 660 660 Weight empty (kg) 65 80 87 Weight full (kg) 365 480 587 DHW Open vented duplex stainless steel thermal stores c/w hot water coil GTHERM300HW GTHERM400HW GTHERM500HW Capacity (ltrs) 300 400 500 Coil rating solar (kw) 6 7.6 7.6 Coil rating DHW (kw) 46.4 55. 55. Standing heat loss (k/4hrs).64.83.98 Height (mm) 650 590 835 Diameter (mm) 555 660 660 Weight empty (kg) 65 80 87 +44 (0)380 73690 www.grantuk.com
Grant ThermaWave connections A B C D E F G Output seven (e.g to DHW kit or flow to DHW cylinder + OSV) T&P Valve (/ BSPF for 50L & 300L and 3/4 for 400L & 500L models) Input one (e.g flow from boiler if DHW is fitted) Output one (e.g CH flow if no DHW is fitted) Thermostat pocket Input two (e.g flow from boiler if no DHW is fitted) Output two (e.g CH flow if DHW is fitted) G* Output two alternative position (e.g. if less DHW is required) H I J K L M N O P Q R S T U V W X Y Z AA BB 8mm gravity flow (e.g solid fuel) Input three (e.g return from DHW kit or cylinder) Output three (e.g to UFH if high capacity) Immersion heater Thermostat pocket Input four (e.g flow from heat pump) Output four (e.g return to boiler) 8mm gravity return (e.g solid fuel) Input five (e.g return from CH) Output five (e.g UFH flow if low capacity) Solar coil return Immersion heater Thermostat pocket Solar coil flow Input six (e.g return from UFH) Output six (e.g return to heat pump) mm fill and drain point 8mm DHW coil flow 8mm DHW coil return Cold mains DHW out Note: The inputs and outputs highlighted above may vary depending upon the technologies being connected to the thermal store, and if a nominal quantity of domestic hot water is also required. For further guidance consult the installation manual or Grant Technical Services. AA A BB A C D C B D E G* F E G F G H ThermaWave DHW unvented models ThermaWave DHW open-vented models P M X K R U L T N Q W ThermaWave open-vented models I M P V K S L O R T U X J N Q W
Grant Thermawave DHW Stores Performance Data Capacity (ltrs) 300 400 500 Draw off * (0l/min at 70 O C) 5 45 75 Reheat time (mins) 4 Draw off * (0l/min at 70 O C) 30 85 355 Reheat time (mins) 0 4 Draw off 3 * (0l/min at 70 O C) 400 40 455 Reheat time (mins) 8 3 35 Note: Draw off provides a final mixed water temerature (e.g. for bath) of 45 o C. Draw off is the top third of the store. Draw off is teh top /3 of the store. Draw off 3 is the full store (without solar thermal input). Reheat times relate to raising the same volume of water back to 70 o C. Grant ThermaWave components Open Vented Models ltr shock arrestor mm thermostatic mixing valve mm x mm / BSPF fitting 3 bar/6bar inlet group (optional extra) Sealed System Models ltr shock arrestor mm thermostatic mixing valve mm x mm / BSPF fitting 3 bar/6bar inlet group (optional extra) Expansion vessel Expansion vessel bracket/hose Reducer fitting (400/500ltr models only) mm x mm x 3/4 BSPF fitting / BSPM to 5mm fitting (90 o ) Filling loop kit PRV & Pressure gauge 80 o C limit stat Electrical control box ThermaWave DHW ThermaWave +44 (0)380 73690 www.grantuk.com 3
Solar Thermal Range Available in kits High efficiency flat plate collector Multifunctional controller In-roof, on-roof & flat roof options New compact pump station Solar Keymark approved Solar Keymark Collector Information Length (mm) 043 Width (mm) 43 Depth (mm) 80 Collector gross area (m ).34 Aperture/absorber area (m ).4 Weight (kg) 40 Glass tyoe ESG, Durasolar P+ Sandy Glass Thickness (mm) 3. Degree of efficiency no (%) 8.6 Effective thermal capacity(kj/m K ) 60 Conversion factor ( ) 0.86 Linear heat loss coefficient (a ) 4.4 Linear heat loss coefficient (a ) (W/m K ) 0.008 Stagnation temperature * ( o C) 77 Maximum operating pressure (bar) 0 Fluid content (ltr).6 Tilt angle (maximum/minimum) ( o ) 0/90 Pressure drop (at.5l/min solar fluid) (mbar) 05 *Test conditions - Irradiance 000W/m Ambient temperature 30 C 4
Solar irradiation in the UK and Ireland The diagram below shows the total average solar radiation falling on m surface, inclined at 30 to the horizontal, measured in kilowatt-hours. The average property requires approximately 3,000 kwh per year for domestic water heating. How to calculate the number of collectors required South Direction of roof Solar radiation (see above map) Number of people per household kwh/year <3 4 5 6 900-000 000-00 00-00 3 South west/ South East 900-000 000-00 00-00 3 3 3 West 900-000 000-00 00-00 3 3 3 4 3 3 East 900-000 000-00 00-00 3 3 3 3 4 3 3 Cylinder requirements are 50-60 litres capacity per m of nett collector area. To simplify this, for a -collector system of x.4 = 4.8m, you would require a cylinder of approximately 00-50 litres. This should be sufficient for 4 people and satisfy up to 70% of your hot water demand per annum. +44 (0)380 73690 www.grantuk.com 5
SAHARA Portrait Kits (On-Roof Mounting Options) GSSKIT0 Collector Bronze On-Roof Solar Collector (Bronze) Connection kit flow and return Collector on roof extra set Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve Roof Anchors: Anchors for profile tile (Pack of ) Anchors for flat tile (Pack of ) Anchors for slate tile (Pack of ) QTY Pks Pks Pks GS773 GS46 GS74 GS54H GS765 GS076 GS07 GS074 GS073 GS48 GS088 GS090 GSSKIT Collector Bronze On-Roof Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector portrait rails and fixings Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve Roof Anchors: Anchors for profile tile (Pack of ) Anchors for flat tile (Pack of ) Anchors for slate tile (Pack of ) QTY 3 Pks 3 Pks 3 Pks GS773 GS46 GS068 GS74 GS54H GS765 GS075 GS076 GS07 GS074 GS073 GS48 GS088 GS090 GSSKIT 3 Collector Bronze On-Roof Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector portrait rails and fixings Collector on roof extension kit Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve Roof Anchors: Anchors for profile tile (Pack of ) Anchors for flat tile (Pack of ) Anchors for slate tile (Pack of ) QTY 3 4 Pks 4 Pks 4 Pks GS773 GS46 GS068 GS74 GS74 GS54H GS765 GS076 GS07 GS074 GS073 GS48 GS088 GS090 6
SAHARA Portrait Kits (In-roof Mounting Options) GSSKIT5 Collector Bronze In-Roof (TILE) Solar Collector (Bronze) Connection kit flow and return Collector Portrait In-Roof Kit - Tile Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS5547 + GS5545 GS54H GS765 GS076 GS07 GS074 GS073 GSSKIT6 Collector Bronze In-Roof (SLATE) Solar Collector (Bronze) Connection kit flow and return Collector Portrait In-Roof Kit - Slate Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS5549 + GS5545 GS54H GS765 GS076 GS07 GS074 GS073 GSSKIT3 Collector Bronze In-Roof (TILE) Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector Portrait In-Roof Kit - Tile Roof Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS068 GS5546 + GS5544 GS54H GS765 GS075 GS076 GS07 GS074 GS073 GSSKIT7 Collector Bronze In-Roof (SLATE) Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector Portrait In-Roof Kit - Slate Roof Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS068 GS5548 + GS5544 GS54H GS765 GS075 GS076 GS07 GS074 GS073 +44 (0)380 73690 www.grantuk.com 7
GSSKIT4 3 Collector Bronze In-Roof (TILE) Solar Collector (Bronze) Connection kit flow and return Connection kit connector to connector Collector portrait In-Roof kit - Tile Roof Collector portrait In-Roof extension - Tile Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY 3 GS773 GS46 GS068 GS5546 + GS5544 GS555 + GS5545 GS54H GS765 GS076 GS07 GS074 GS073 GSSKIT8 3 Collector Bronze In-Roof (SLATE) Solar Collector (Bronze) Connection kit flow and return Connection kit connector to connector Collector portrait In-Roof kit - Slate Roof Collector portrait In-Roof ext - Slate Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY 3 GS773 GS46 GS068 GS5548 + GS5544 GS5545 + GS5550 GS54H GS765 GS076 GS07 GS074 GS073 SAHARA Portrait Kits (Flat-roof Mounting Options) GSSKIT5 Collector Bronze Flat-Roof Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector portrait Flat Roof rails & fixings Collector portrait Flat Roof Kit Collector portrait Flat Roof Cruciform Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS068 GS74 GS08 GS69 GS54H GS00 GS075 GS076 GS07 GS074 GS073 For bespoke kits please contact our sales team on +44 (0)380 73690 8
Grant CombiSOL Designed by Grant Compatible with most combination boilers Accurately regulates inlet water temperature COMSOL3 Description Thermostatic Solution for linking Combi boilers to Solar Thermal pre-heat cylinders Grant WinterSOL Designed by Grant Provides a fully heated cylinder of hot water at times of low solar gain Operates during programmed hot water periods WINTERSOL Description Recirculating/ Sanitising solution (heats complete solar cylinder when there is no solar gain) +44 (0)380 73690 www.grantuk.com 9
Grant Spira Wood Pellet Boiler Range Highly efficient condensing boiler MCS approved Modulating burner Integrated pellet store 5mm conventional flue Automatic pellet feed and ignition Award winning condensing heat exchanger Flue box with integral fan/ draught stabiliser Automatic wash system for condensing unit Exempt under the Clean Air Act Internal Standard Models Including Pellet Store and Auger(s) Product Code Btu/h x000 Output KW Description WPS66 RH0 0-90 6-6 WPS66 LH0 0-90 6-6 WPS66 RH00 0-90 6-6 WPS66 LH00 0-90 6-6 WPS936 RH0 30-3 9-36 WPS936 LH0 30-3 9-36 WPS936 RH00 30-3 9-36 WPS936 LH00 30-3 9-36 WPS5 40-80 -5 WPS56 50-3 5-6 6kW wood pellet boiler c/w 0 right hand single hopper and feed auger 6kW wood pellet boiler c/w 0 left hand single hopper and feed auger 6kW wood pellet boiler c/w 00 right hand single hopper and feed auger 6kW wood pellet boiler c/w 00 left hand single hopper and feed auger 36kW wood pellet boiler c/w 0 right hand single hopper and feed auger 36kW wood pellet boiler c/w 0 left hand single hopper and feed auger 36kW wood pellet boiler c/w 00 right hand single hopper and feed auger 36kW wood pellet boiler c/w 00 left hand single hopper and feed auger x 6kW wood pellet boilers c/w 40 dual hopper and feed augers 6kW & 36kW wood pellet boilers c/w 40 dual hopper and feed augers 30
Spira Model Maximum heat output Units 6-6 9-36 kw 6 36 Btu/hr 88,700,800 Flow connection BSP Female /4 Female Return connection BSP Female /4 Female Water content Ltr 5.5 60 Waterside resistance rt = 0 o C mbar 6.0 Waterside resistance rt = 0 o C mbar 9.5 Mains water (cleaning system) bar bar operating pressure Condensate connection - /4 BSP Female Conventional flue - 5mm (5 ) Black System Combustion chamber draught requirement mbar 0.0 to 0.5 (running) Maximum static head m 5 Minimum circulating head m Boiler temperature set point range o C 55 to 75 Boiler temperature cut out point o C 65 to 80 Minimum return temperature o C 40 Watery system overheat thermostat cut-out o C 0 Burn-back overheat thermostat cut-out o C 60 Electricity supply - 30V - 50Hz Max operating pressure - sealed system bar.5 Max operating pressure - open system bar.5 Maximum auger length (bulk hopper) m 6.0 Maximum auger speed (bulk hopper) rpm 30 Minimum flue length m.0 Maximum flue length m.0 Heating element rating Watts 450 Intermediate auger motor power Watts 55 Intermediate auger motor starting current Amps 0.64 Intermediate auger motor running current Amps 0.64 Intermediate auger speed rpm 8. Flue fan motor power Watts 3 Flue fan motor starting current Amps 0.7 Flue fan motor running current Amps 0.3 Cleaning solenoid power Watts 0 Cleaning solenoid current Amps 0.087 Burner fan motor power Watts 56 Total burner start current Amps.5 Total burner run current Amps 0.60 +44 (0)380 73690 www.grantuk.com 3
Spira 6-6kW & 9-36kW boiler dimensions Rear view Side view Front view Grant Spira Model Dimensions (mm) A B C 6-6kW 0kg left/right hand hopper 58 0 96 6-6kW 00kg left/right hand hopper 79 0 49 9-36kW 0kg left/right hand hopper 58 0 96 9-36kW 00kg left/right hand hopper 79 0 49 3
Spira -5kW, 5-6kW & 8-7kW boiler dimensions Rear view Front view Side view Grant Spira Model Dimensions (mm) A B -5KW 40kg double hopper 66 0 5-6kW 40kg double hopper 66 0 8-7kW 40kg double hopper 66 0 Boiler and Hopper Weights (kg) Spira model 6-6 9-36 Boiler - less burner & fan box (empty) 0 3 Burner 5.5 5.5 Fan box 5 5 Total boiler weight (empty) 3.5 6.5 Total boiler weight (full) 83 3.5 0kg pellet hopper incl auger (empty) 4.35 4.35 0kg pellet hopper incl auger (full) 5.35 5.35 00kg pellet hopper incl auger (empty) 77 77 00kg pellet hopper incl auger (full) 77 77 Auger 8.35 8.35 40kg pellet hopper incl x augers (empty) 4 4 40kg pellet hopper incl x augers (full) 8 8 +44 (0)380 73690 www.grantuk.com 33
Grant SpiraPod Outdoor Boiler Housing Purpose built external housing for the Grant Spira Accommodates all Spira models from 6-36kW Designed and manufactured by Grant Fully weather proof steel casing Iconic Grant grey powder coated finish Top fill integral hopper with 90kg capacity Suitable for vacuum feed Optional internal pellet vacuum system Lockable doors Sealed system kit can be fitted within the pod SpiraPod Outdoor Boiler Housing Description WPSPOD6 SpiraPod 6kW wood pellet boiler and external casing WPSPOD36 SpiraPod 36kW wood pellet boiler and external casing 34
Grant Vecta Internal and External Wood Pellet Boiler Range Highly efficient MCS approved (from date of release) Top fill 60kg integrated pellet store Built in weather compensation Automatic pellet feed and ignition Award winning condensing heat exchanger Automatic wash system for condensing unit Self-cleaning system for heat exchanger and burner brazier Simple to install and maintain Whisper quiet operation Exempt under the Clean Air Act (from date of release) Vecta Condensing Wood Pellet Boilers Internal white cased model WVP4/6 Boiler Output (kw) 4-6 Boiler Weight (empty) (kg) 55 Boiler Weight (full) (kg) 93 Flue (mm) 5 Wash system (condensing unit) (mm) 5 Flow/return connection (mm) Condensate drain /4 female Water content (litres) 38 Electrical supply 30V ph Integrated hopper size (kg) 60 Vecta Condensing Wood Pellet Boilers External powder coated module WVP4/6EXT Boiler Output (kw) 4-6 Boiler Weight (empty) (kg) TBC Boiler Weight (full) (kg) TBC Flue (mm) 5 Wash system (condensing unit) (mm) 5 Flow/return connection (mm) Condensate drain /4 female Water content (litres) 38 Electrical supply 30V ph Integrated hopper size (kg) TBC +44 (0)380 73690 www.grantuk.com 35
Grant Wood Pellet Store Range Designed and manufactured by Grant Galvanised steel construction Quick seal joints Universal auger or vacuum connection Internal or external installation Low level connection for ease of filling Extremely robust construction Easy access maintenance door for cleaning Code Size (tonne) Grant Pellet Store Models Finish Footprint (metre) Height (mm) Weight (kg) WPXG05TP 0.5 Painted x 375 * 70 WPXG075TP 0.75 Painted x 75 * 83 WPXG5T.5 Galvanised x 395 * 30 WPXGT Galvanised x 700 * 360 WPXG5T.5 Galvanised x 900 * 375 WPXG3T 3 Galvanised x 395 * 40 WPXG35T 3.5 Galvanised x 700 * 47 WPXG4T 4 Galvanised x 900 * 493 WPXG5T 5 Galvanised x 300 * 555 WPXG6T 6 Galvanised x 3400 * 577 * Please allow additional clearance of 450mm for store lid. Painted Pellet Store 500kg and 750kg models come ready assembled 36
Grant SpiraVac Wood Pellet Vacuum Designed and manufactured by Grant Simple to install Gives more flexibility with boiler installation Can be retrofitted to existing boiler Maximum hose length of 0m Lifts pellets up to a height of 3m Only for use with the Grant Spira boiler ranges Grant SpiraVac Models Code WPV/KIT5INT WPV/KIT0INT WPV/KIT5INT WPV/KIT0INT WPV/KIT5POD WPV/KIT0POD WPV/KIT5POD WPV/KIT0POD Description SpiraVac Internal Spira Vacuum kit - 5 metres SpiraVac Internal Spira Vacuum kit - 0 metres SpiraVac Internal Spira Vacuum kit - 5 metres SpiraVac Internal Spira Vacuum kit - 0 metres SpiraVac SpiraPod Vacuum kit - 5 metres SpiraVac SpiraPod Vacuum kit - 0 metres SpiraVac SpiraPod Vacuum kit - 5 metres SpiraVac SpiraPod Vacuum kit - 0 metres External bulk pellet store Flexible hoses SpiraVac vacuum unit Boiler/Hopper SpiraVac auger unit +44 (0)380 73690 www.grantuk.com 37
Energy Management Control Systems GEO30 Reduces heating bills Easier system installation and commissioning Environmentally friendly Suitable for systems up to 65kW Individually controlled heat circuits Option to switch the system to hot water priority Allows a number of heating appliances to be combined, including renewable technologies Provides boiler lead/lag rotaion, equalising appliance running time Maximises overall boiler/ appliance efficiency Tailored system concept drawings for both plumbing and wiring available GES64 Grant Energy Management Controllers GEO360/8 GEO360/35 GEO360/KV6 GEO360/KV8 Description GEO360 Weather compensator with 8mm valves (suitable for Vortex Pro 6-46kW, Vortex Eco 6-35kW) GEO360 Weather compensator with 35mm valves (suitable for Vortex Pro 46-70kW) GEO360 Weather compensator with KV6.3 valve (suitable for Vortex Eco 5-kW, Eco Wallhung -kw) GEO360 Weather compensator with KV8 valve (suitable for Vortex Pro 5-6kW, Vortex Eco -6kW, Spira 6-36kW) GHS/GEO360 GEO360 for Grant low loss header system (no valve body) GES64 GES64 sequence controller (for to 4 heat sources) Grant RSKIT Programmable Room Thermostat RSKIT Description Programmable Room Thermostat (to suit all Grant heating appliances) 38
Grant Low Loss Headers (for systems up to 70kW) GHS70/5 GHS70/53 GHS70/54 GHS70/55 Description flow and return distributor ( zone) flow and return distributor (3 zone) flow and return distributor (4 zone) flow and return distributor (5 zone) GHS70/56 flow and return distributor (6 zone) GHS60/5 /4 hydraulic switcher Accessories GHS/WF00 GHS/WF50 Header bracket set wrap over 00mm Header bracket set wrap over 50mm GHS/WFHV Header bracket set 90 GHS0569 GHS/066M GHS/SG50 /4 connector (quantity: ) Please note: connectors per switcher required Isolation valve (quantity: ) Please note: valves per pump station required Safety set up to 50kW (3 bar PRV) Please note: if 70kW please use GHS/SG00 Technical Specification Maximum flow rate Insulation box Pump unit connection Hydraulic switcher connection Side connection up to 3m 3 /h, 6bar 0 x 0 x 508mm (min) - 508mm (max) (depending on model) male /4 male 3 /4 female Hydraulic switcher (70kW) Distributor (70kW) +44 (0)380 73690 www.grantuk.com 39
Grant Low Loss Headers (for systems up to 65kW) GHS80/5 GHS80/53 GHS80/54 GHS80/55 Description /4 flow and return distributor ( zone) /4 flow and return distributor (3 zone) /4 flow and return distributor (4 zone) /4 flow and return distributor (5 zone) GHS80/56 /4 flow and return distributor (6 zone) GHS80/570 vertical hydraulic switcher Accessories GHS/WF60 GHS/WFHV60 GHS07699 GHS/55AMMS GHS/HT07 GHS/SG00 Header bracket set wrap over 60mm Header wall fixing set - 60mm connection kit /4 isolation valve (quantity: ) - please note: valves per pump station required nut & gasket for /4 isolation valves (quantity: ) - please note: sets of nut & gaskets per pump station required Safety set up to 00kW (3 bar PRV) Technical Specification Maximum flow rate Insulation box Pump unit connection Hydraulic switcher connection Side connection up to 7m 3 /h, 6bar 5 x 5 x 65mm (min) - 65 (max) (depending on model) /4 male male male Distributor and hydraulic switcher Zone pump kit (constant) 40
Zone Pump Kits (for systems up to 70kW) GHS/CT0 Description Constant temperature/variable speed 6 metre zone pump kit GHS/CT0 Constant temperature/variable speed 8 metre zone pump kit GHS/VT03 GHS/VT04 Variable temperature/variable speed 6 metre zone pump kit Variable temperature/variable speed 8 metre zone pump kit Zone Pump Kits (for systems up to 65kW) GHS/CT05 GHS/CT06 GHS/VT07 GHS/VT08 Description 3mm constant temperature/variable speed 7 metre zone pump kit 3mm constant temperature/variable speed 8 metre zone pump kit 3mm variable temperature/variable speed 7 metre zone pump kit 3mm variable temperature/variable speed 8 metre zone pump kit Comprises Technical Specification Zone pump kits (constant speed) Unmixed Zone pump, isolator ball valves, temperature gauges and non-return valve Connection sizes Dimensions and /4 BSP 50 x 380 x 90mm Maximum temperature 0 C Application Flow For power up to 50kW and maximum flow 50 l/hr 6m, 7m or 8m circulating pump Comprises Zone pump kits (variable speed) Unmixed Zone pump, isolator ball valve, temperature gauges and non-return valve, 3-port mixing valve Connection sizes Dimensions Maximum temperature Application Flow and /4 BSP 50 x 380 x 90mm 0 C For power up to 35kW and maximum flow 500 l/hr 6m, 7m or 8m circulating pump, 3-way mixing valve for weather compensation using a Grant GEO360 Control +44 (0)380 73690 www.grantuk.com 4
Grant Training Academy The OFTEC Award Winning Grant Training Academy demonstrates the commitment of Grant UK to providing professional training for heating engineers. Our purpose built training facilities include air-conditioned lecture rooms, an extensive oil boiler training workshop and a renewables training and assessment workshop complete with a full size training roof, working solar thermal, Vecta and Spira biomass boilers, air source heat pump and thermal store installations, solar thermal training/assessment rig and unvented hot water training and assessment rigs. This allows us to offer a wide range of training courses including Grant product training courses, OFTEC training and assessment and Logic Certification courses. In addition to the facilities, the Grant training staff have both a wealth of experience and technical knowledge of oil fired domestic boilers, heating systems and installation practice. This combination has resulted in the Grant UK Training Academy winning OFTEC Training Centre of the Year in 003, H&V News Award for Excellence in 004, followed by OFTEC Regional Training Centre of the year in 005 and 006 and OFTEC Training Centre of the Year again in 008, 00 and 0. 4
Local Training We realise that not everyone can make it to the Training Centre in Devizes, so we can organise and deliver off site training courses for installers and commissioning /service technicians. These include OFTEC 0-05E/0-600A training/assessment as well as free of charge Grant product training sessions. Off site training courses are delivered by our own instructors and are usually arranged in conjunction with local Grant stockists, fuel suppliers, heating contractors, or other technical colleges or training centres. GTEC Training Centre Grant UK has joined forces with GTEC Training at its purpose built Building Services Technology Centre in Hawes, North Yorkshire. As a result of this strategic partnership, Grant UK training courses are now available in the north of England making them far more accessible for installers living in the northern part of the UK. A schedule of our upcoming courses is available on our website: www.grantuk.com If you would like to know more about the training courses provided by Grant UK, or wish to enrol on a course with Grant, then please either call +44 (0)380 736943 or contact training@grantuk.com +44 (0)380 73690 www.grantuk.com 43
This leaflet is accurate at the time of printing but as Grant UK has a policy of continual improvement it may be superseded. We reserve the right to amend specifications without prior notice. The statutory rights of the consumer are not affected. All products manufactured under I.S. EN ISO 900. Grant UK additionally holds ISO 400 accreditation. THE GRANT EZ-FIT FLUE SYSTEM is a trade mark of Grant Engineering Limited. Grant Aerona, Grant Spira, Grant Vecta, Grant Vortex, Grant Solar, Grant Aurora, Grant Sahara, Grant CombiSOL, Grant WinterSOL, Grant MonoWave, Grant DuoWave, Grant ThermaWave, Euroflame and Multi Pass are registered trade marks of Grant Engineering Limited. The contents of this leaflet are fully protected by copyright and nothing may be reproduced without permission from Grant UK. Grant Engineering (UK) Ltd Hopton House, Hopton Industrial Estate, Devizes, Wiltshire, SN0 EU t: +44 (0)380 73690 f: +44 (0)380 73699 e: info@grantuk.com w: www.grantuk.com GPG 05/5 UK