INSTALLATION INSTRUCTIONS M-00 (MH 8) CROSS HANDLE -HOLE BASIN MIXER WITH P.U.W. M-0 (ML 8) LEVER -HOLE BASIN MIXER WITH P.U.W. M-00 (MH 8) M-0 (ML 8)
Dimensions in Inches (& Millimetres) M-00 (MH 8) "~" (.~0mm) /" (8.mm) /" (0mm) Ø /" (Ømm) /8" (0mm) /"-NPSM "-0UNEF /8" (0mm) /" (0mm) /8" (80mm) " (0mm) /"-NPSM 8" (0.mm) /"~" /" (8.~0.8mm) (.mm) " (mm) 8"Max (0mm) /" (.mm) /"-8UNEF H /8" (H0mm) /"~ /" (mm~mm) Ø /" Ø(.mm) M-0 (ML 8) "~" /8" (.~0mm) (80mm) /" (8.mm) /" (0mm) Ø /" (Ømm) /8" (0mm) /8" (0mm) /" (0mm) /8" (80mm) H /8" (H0mm) /"-NPSM "-0UNEF " (0mm) /"-NPSM 8" (0mm) /"~" /" (8.~0.8mm) (.mm) " (mm) 8"Max (0mm) Ø /" (Ø.mm) /"-8UNEF /"~ /" (~mm) Ø /" (Ø.mm) Whilst every effort is made to ensure accuracy, design and dimensions are subject to change without notice as part of the company s product development process.
What you need to know Tools: Adjustable Wrench Groove Joint Pliers Hacksaw Phillips Screwdriver Pipe Tape Spatula Spirit Level Safety Tips If you are soldering during faucet installation, remove cartridges, seats, gaskets and washers prior to applying flame, otherwise you will void the warranty. Cover drain openings to avoid losing small parts. When cutting or soldering pipe, use safety glasses to protect your eyes. Maintenance Your new bathroom faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, wire wool and harsh chemicals as these will dull the finish and void your warranty. Important Points Prior to beginning installation. turn off the cold and hot water lines and open the old faucet to release built-up pressure. Overtightening nuts may cause damage. Wrap all threaded connections with pipe tape available at your local plumbing supply store. Always wrap in a clockwise direction. The fittings should be installed by a state-licenced plumber. Things You May Need Correct installation may vary depending on previous faucet installation. All necessary supplies required for faucet installation are not included, but may be found where plumbing supplies are sold. It is suggested that IAPMO and/or CSA approved plumbing supplies are used during installation. Standards IAPMO/cUPC Listed Meets NSF -9 Meets A.8. Flow Rate 0 0 0 0 80PSI Please note : Final achievable flow rate is dependent on the outlets fitted, see relevant outlets (spouts, roses, sprays) for fully assembled product flow rate.
Steps - Installation Procedure Lefroy Brooks always recommends that plumbing products be installed by a licensed professional. Shut off main water supply before installation. Install left handle assembly, headwork cover and side body. Install other handle assembly, headwork cover and side body. Fit spout and install the connector assembly.
Steps Installation Procedure Lefroy Brooks always recommends that plumbing products be installed by a licensed professional. Shut off main water supply before installation. Install Pop-up rod. Connect Pop-up rod. Connect flexi-hoses. Warning! When installing flexible hose, Please notice:. There should be no torsion or deformation. Do not fold into a V or L shape.. Do not use if there is any crack or deformation.
Exploded View Parts List M-00 (MH 8) 9 0 8 9 8 0 9 8 9 0 0 8 8 9 0 Handle ( H ) (098H) Handle ( C ) (098C) Set screw (998) Screw (0089) Canopy (0800) Clip (0) Extension stem (009) Cartridge (090N) Escutcheon (0) O-ring (00) Oil-seal (000) Washer (08) Nut (0098) Body (089W) 8 9 0 8 Pop-up knob (8) O-ring (080N) O-ring (000N) O-ring (0000N) Brass tube (0N) O-ring (000N) Connection tube (00W) O-ring (00N) O-ring (0000N) Spacer (000) Washer (00) Nut (009009) Connector (000W) Nut (00900) 9 0 8 9 0 Pop-up rod () Spout (00W) Oil-seal (0009N) Aerator insert (0N) Aerator housing (00N) Connector (0) Pop-up rod (00) Pop-up waste (8) Flexible hose (00W) Pipework nuts (000) Allen key (0000) Spanner (00)
Exploded View Parts List M-0 (ML 8) 8 8 9 9 0 8 0 9 0 8 9 0 8 9 0 Handle ( C ) (098C) Handle ( H ) (098H) Set screw (998) Screw (0089) Canopy (0800) Clip (0) Extension stem (009) Cartridge ( Cold ) (0N) Cartridge ( Hot ) (0N) Escutcheon (0) O-ring (00) Oil-seal (000) Washer (08) Nut (0098) 8 9 0 8 Body (089W) Pop-up knob (90-0) O-ring (080N) Spout (00W) O-ring (000N) O-ring (0000N) Brass tube (0N) O-ring (000N) Connection tube (00W) O-ring (00N) O-ring (0000N) Spacer (000) Washer (00) Nut (009009) 9 0 8 9 0 Connector (000W) Nut (00900) Oil-seal (0009N) Aerator insert (0N) Aerator housing (00N) Pop-up rod () Connector (0) Pop-up rod (00) Pop-up waste (8) Flexible hose (00W) Pipework nuts (000) Allen key (0000) Spanner (00)
For additional assistance or service call 8-0-9 9am to pm EST Monday to Friday www.lefroybrooks.com LEFROY BROOKS INC, 88 TROUTMAN STREET, RIDGEWOOD, NY, 8 TELEPHONE: 8-0-9. FAX: 8-0- The use of trademarks, product design and artwork is subject to licence or agreement with Christo A. Lefroy Brooks. The design registrations, trademark registrations and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited. The right to modify designs and dimensions is reserved. Christo Lefroy Brooks is a member of ACID (Anti Copying in Design). CHRISTO A. LEFROY BROOKS 009