INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Kleppe Lane Sparks, NV 89-667 (77) 9-72 Fax (77) 9-72 E-mail: haws@hawsco.com website: www.hawsco.com Model 0/0HPS Drinking Fountain NOTE TO INSTALLER: Please leave this information with the Maintenance Department. No. 207620(20) LIMITED WARRANTY HAWS warrants that this specific product is guaranteed against defective material or poor workmanship for a period of one year from date of shipment. HAWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to Haws within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above. Buyer agrees that HAWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale. The drinking fountain manufactured by HAWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose for which they were intended. NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR GIVEN BY HAWS. SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL PLEASE CALL: TECHNICAL SUPPORT: -800-766-62 FOR CUSTOMER SERVICE: -888-60-297 02/8 Model 0/0HPS Page of
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 2" adjustable wrench, 0" pipe wrench, /2 and /2 hex key wrench, 9/6, /2", 7/6 socket wrench or open end wrench. LOCATION OF UNIT: The Model 0/0HPS Drinking Fountain is a wheelchair accessible drinking water facility. The height dimensions shown, meet current ADA requirements. When installing this unit, local, state or federal codes should be adhered to. If height other than shown is required, then dimensions must be adjusted accordingly. SUPPLY LINE: The minimum recommended line size is /2 IPS with 0-90 psi (2-6 ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter is recommended. PLUMBING CONNECTIONS: Inlet is /8 O.D. push-in type fitting. Waste outlet is -/ O.D. tube. MAINTENANCE: Periodically clean the strainer. Refer to 87 Series Valve Manual for more information. GENERAL NOTES: INSTALLATION PROCEDURE. For all plastic push-in type fitting connections, only connect NSF-6 copper or plastic tubing. Stainless steel or glass tubing is not recommended. The following assembly instructions must be followed to ensure a watertight connection: a. Cut tubing square and clean. b. Mark from end of tube the length of insertion (See table below). c. Push tube into the fitting until it bottoms out. d. To remove, depress collet and pull tubing out. Tube Sizes O.D. Tolerance Insertion Depth / ±.00 /6 /8 ±.00 / /2 ±.00 7/8 02/8 Model 0/0HPS Page 2 of
PROBLEM TROUBLESHOOTING REPAIR CHECKLIST. Insufficient bubbler flow. a. Check that inlet screwdriver stop valve is in wideopen position. (Customer supplied). Turn counterclockwise. b. Verify minimum 0 psi flowing supply pressure. c. Clean strainer. See 87 Series Valve Manual. d. Adjust valve to increase flow. Use front adjust screw or see 87 Series Valve Manual. e. Clean screens (inside nozzle body). Unscrew nozzle insert and very gently activate water supply to pop out qty. screens (be careful not to lose screens). Remove any debris clogging the screen openings and place back into nozzle body. Reassemble nozzle insert. For more information about Haws products, see our website: www.hawsco.com 208 Haws Corporation All Rights Reserved HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 02/8 Model 0/0HPS Page of
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. NOTES: 87PBF (ITEM 2) INCLUDES VRK87 CARTRIDGE ASSEMBLY (ITEM ) AND PBA6 FLANGED PUSH BUTTON (ITEM ). A * * ITEM DESCRIPTION 0 BUBBLER HEAD, PCP 70 2 BUTTON, PUSH, PCP, FLANGED W/ VALVE 87PBF VALVE REPAIR KIT VRK87 BUTTON, PUSH, 87, FLANGED PBA6 PANEL, BACK, F/ SATIN SWIRL OR HI-POL SS 00002000 6 PLATE, MOUNTING 6700. 7 STRAINER, WASTE ASSEMBLY, SCP OR PCP 66 8 PANEL, ACCESS, SS SATIN OR HI-POL 660 9 PLATE, BOTTOM, F/ 000 PBM000 0 DRIVER, NOZZLE,.2 HEX 00020822 * DENOTES OPTIONAL PART. 0HPS 70 87PBF VRK87 PBA6 0000202 6700. 66PCP 660HPS PBM000 00020822 2 7 6 8 70LAMIN (OBSOLETE - SHOWN FOR REFERENCE ONLY) 0 (OPTIONAL) FOR REMOVAL OF NOZZLE WITH TUBE 9 STYLE A (TUBING CONNECTS TO ELBOW) STYLE B (TUBING CONNECTS TO INSERT ASSY) FOUNTAIN COULD HAVE EITHER STYLE DETAIL A ROTATED 90 INTO VIEW PARTS BREAKDOWN KLEPPE LANE SPARKS, NEVADA 89 (77) 9-72 FAX (77) 9-72 E-MAIL: HAWS@HAWSCO.COM WEBSITE: WWW.HAWSCO.COM ECN NO. REVISED PER BY MODEL(S) PART NUMBER. ECN: 27 VWC DRAWN DATE CHKD 0/0HPS REVISION RM 0/9/98 VWC APPROVED DATE DRINKING FOUNTAIN 20 FV 02/2/8 SCALE: : DRAWING TYPE: PARTS BREAKDOWN SIZE: A SHEET OF WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER. C 207 Haws Corporation - All Rights Reserved R HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 000207620 PAGE of
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. NOTES:. HOLD ROUGH-IN DIMENSIONS ±/8" (.2mm). 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN. MOUNTING BOLTS INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION. REMOVE VALVE FROM PUSH BUTTON TO INSTALL WASTE ELBOW ONTO BOWL. AFTER WASTE ELBOW IS INSTALLED, REINSTALL VALVE AND ADJUST FLOW. REFER TO 87 SERIES OPERATION AND MAINTENANCE MANUAL FOR PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTRUCTIONS. [9] 6 [06] of PAGE 6 [06] DETAIL A SCALE : 2 2 [8] -/" O.D. WASTE BEND (SUPPLIED) BACK PANEL (SUPPLIED) WALL FACE 9 /8 [7] WALL STUD WASTE BEND AND -/" IPS TRAP 6 [06] [76] 6700. MOUNTING PLATE (BEHIND FINISH WALL) Ø/8" SUPPLY TUBING AND SCREWDIRVER STOP 2 [] [76] 8X /8-6 UNC X ø7/6" [ø] 6 / [2] 7/8 [7] 2 /2 [68] 99mm 9-/2" (TO SPOUT OUTLET) 867mm -/2" (TO SPOUT OUTLET) 27 [686] A WALL FACE FLOOR LINE 27 7/8 [708] WASTE 28 / [70] SUPPLY 2 7/8 [8] WASTE / [87] SUPPLY 7 /8 [82] 2 /8 [] 6 [06] 6 [06] 6 [9] 6700. MOUNTING PLATE MUST BE INSTALLED BEFORE FINISH WORK. THIS PLATE IS A STANDARD ITEM. 0 [2] 2 [0] C OPTIONAL TRAP ACCESS PANEL MODELS 660 AND 660HPS KLEPPE LANE SPARKS, NEVADA 89 (77) 9-72 FAX (77) 9-72 E-MAIL: HAWS@HAWSCO.COM WEBSITE: WWW.HAWSCO.COM ECN NO. REVISED PER BY: MODEL(S) PART NUMBER. ECN: 27 VWC DRAWN: DATE: CHK'D.: 0/0HPS REVISION RM 0/98 VWC APPROVED: DATE: DRINKING FOUNTAIN 20 FV 02/2/8 SCALE: : DRAWING TYPE: INSTALLATION SIZE: A SHEET OF R 207 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 000207620.D