SERVICE FACTS Gas Furnaces Upflow & Downflow Induced Draft Stage Heat Models: M80P00AU2AA M80P060AU2AA M80P060AU36AA M80P080BU36AA M80P080BU8AA M80P00BU36AA M80P00CU8AA M80P00CU60AA M80PDU60AA M80P0DU60AA M80P060AD2AA M80P060AD36AA M80P080BD5AA M80P00CD8AA M80P00CD60AA M80-SF-C M80PDD60AA M80P0DD60AA IMPORTANT This document contains a wiring diagram and service information. This is customer property and is to remain with this unit. Please return to service information pack upon completion of work. DISCONNECT POWER BEFORE SERVICING MODEL TYPE RATINGS 2 Input BTUH 3 Capacity BTUH (ICS) 3 Temp. rise (Min.-Max.) F. BLOWER DRIVE Diameter - Width (In.). Used Speeds (.) CFM vs. in. w.g. Motor HP R.P.M. COMBUSTION FAN - Type Drive -. Speeds Motor HP - RPM FLA FILTER Furnished? Type Recommended Hi Vel. (.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type - Fired - Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.) / Net (Lbs.) M80P00AU2AA 0,000 3,000 0 x 6 /5 080-6x25 - in. Round - 2 5 2 56 2 5. 5-3/ x 6- x 30-9 / 0 PRODUCT SPECIFICATIONS M80P060AU2AA 60,000 7,000 0 x 6** /3 075-6x25 - in. Round 3 5 3 56 3 9.0 5-3/ x 6- x 30-27 / 8 M80P060AU36AA 60,000 7,000 0 x 6** /3 075-6x25 - in. Round 3 5 3 56 3 9.0 5-3/ x 6- x 30-27 / 8 M80P080BU36AA 80,000 63,000 0 x 7 /3 075-7x25 - in. Round 5 56 9.0 5-3/ x 9- x 30-2 / 32 Central Furnace heating designs are certified to ANSI Z2.7 / CSA 2.3. 2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate % per,000 feet for elevations above 2,000 feet above sea level. For Canadian applications, above input ratings (BTUH) are up to,500 feet, derate % per,000 feet for elevations above,500 feet above sea level. 3 Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. NOTICE: The manufacturer has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice. 3 Ingersoll Rand All Rights Reserved 0/3
MODEL TYPE RATINGS 2 Input BTUH 3 Capacity BTUH (ICS) 3 Temp. rise (Min.-Max.) F. BLOWER DRIVE Diameter - Width (In.). Used Speeds (.) CFM vs. in. w.g. Motor HP R.P.M. COMBUSTION FAN - Type Drive -. Speeds Motor HP - RPM FLA FILTER Furnished? Type Recommended Hi Vel. (.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type - Fired - Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.)/ Net (Lbs.) PRODUCT SPECIFICATIONS M80P080BU8AA 80,000 6,000 0 x 8 /3 075-7x25 - in. Round 5 56 9.8 5-3/ x 9- x 30- M80P00BU36AA 00,000 79,000 0-70 0 x 7 /3 075-7x25 - in. Round The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. MODEL TYPE RATINGS 2 Input BTUH 3 Capacity BTUH (ICS) 3 Temp. rise (Min.-Max.) F. BLOWER DRIVE Diameter - Width (In.). Used Speeds (.) CFM vs. in. w.g. Motor HP R.P.M. COMBUSTION FAN - Type Drive -. Speeds Motor HP - RPM FLA FILTER Furnished? Type Recommended Hi Vel. (.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type - Fired - Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.)/ Net (Lbs.) M80P00CU60AA 00,000 79,000 x 0 075 - x25 - in. Round 5 5 5 56 5 3. -3/ x 23 x 30-62 / 5 M80PDU60AA,000 96,000 x 0 075-2x25 - in. Round 6 5 6 56 6 3. -3/ x 26- x 30-86 / 7 M80P00CU8AA 00,000 79,000 35-65 0 x 8 075 - x25 - in. Round 2 M80-SF-C 5 5 5 56 5 9.0 5-3/ x 9- x 30-5 5 5 56 5.6 5-3/ x 23 x 30-2 / 32 5 / 62 / 5 Central Furnace heating designs are certified to ANSI Z2.7 / CSA 2.3. 2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate % per,000 feet for elevations above 2,000 feet above sea level. For Canadian applications, above input ratings (BTUH) are up to,500 feet, derate % per,000 feet for elevations above,500 feet above sea level. 3 Based on U.S. government standard tests. M80P0DU60AA 0,000,000 0-70 x 0 3/ 075-2x25 - in. Round 7 5 7 56 7 3.8-3/ x 26- x 30-93 / 8
MODEL TYPE RATINGS 2 Input BTUH 3 Capacity BTUH (ICS) 3 Temp. rise (Min.-Max.) F. BLOWER DRIVE Diameter - Width (In.). Used Speeds (.) CFM vs. in. w.g. Motor HP R.P.M. COMBUSTION FAN - Type Drive -. Speeds Motor HP - RPM FLA FILTER Furnished? Type Recommended Hi Vel. (.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type - Fired - Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz Ampacity (In Amps) Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.) / Net (Lbs.) M80P060AD2AA 60,000 8,000 35-65 0 x 7 /5 075 2 - x - in. Round 3 5 3 56 3 5.5 5-3/ x 6- x 30-29 / 9 PRODUCT SPECIFICATIONS M80P060AD36AA 60,000 8,000 x 7 075 2 - x - in. Round M80P080BD5AA 80,000 6,000 35-65 0 x 8 /3 075 2 - x - in. Round - Type I Service Facts Central Furnace heating designs are certified to ANSI Z2.7 / CSA 2.3. 2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate % per,000 feet for elevations above 2,000 feet above sea level. For Canadian applications, above input ratings (BTUH) are up to,500 feet, derate % per,000 feet for elevations above,500 feet above sea level. 3 Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes. MODEL TYPE RATINGS 2 Input BTUH 3 Capacity BTUH (ICS) 3 Temp. rise (Min.-Max.) F. BLOWER DRIVE Diameter - Width (In.). Used Speeds (.) CFM vs. in. w.g. Motor HP R.P.M. COMBUSTION FAN - Type Drive -. Speeds Motor HP - RPM FLA FILTER Furnished? Type Recommended Hi Vel. (.-Size-Thk.) VENT Size (in.) HEAT EXCHANGER Type - Fired - Unfired Gauge (Fired) ORIFICES Main Nat. Gas. Qty. Drill Size L.P. Gas Qty. Drill Size GAS VALVE PILOT SAFETY DEVICE Type BURNERS Type Number POWER CONN. V / Ph / Hz Ampacity (In Amps) M80P00CD60AA 00,000 80,000 x 0 075 2-6x - in. Round - Type I 5 5 5 56 5 2.8 M80PDD60AA,000 96,000 35-65 x 0 075 2-6x - in. Round - Type I 6 5 6 56 6 2.8 M80P0DD60AA 0,000 3,000 5-75 x 0 3/ 075 2-6x - in. Round 7 5 7 56 7 3.8 Max. Overcurrent Protection (Amps) PIPE CONN. SIZE (IN.) DIMENSIONS Crated (In.) WEIGHT Shipping (Lbs.) / Net (Lbs.) 5-3/ x 23 x 30-67 / 55 5-3/ x 26- x 30-89 / 76-3/ x 26- x 30-96 / 83 3 5 3 56 3.6 5-3/ x 6- x 30-29 / 9 M80-SF-C 3 5 56 9. 5-3/ x 9- x 30-6 / 35 M80P00CD8AA 00,000 80,000 35-65 0 x 8 075 2-6x - in. Round 5 5 5 56 5.6 5-3/ x 23 x 30-66 / 5
SAFETY SECTION CARBON MONOXIDE POISONING HAZARD Failure to follow the steps outlined below for each appliance connected to the venting system being placed into operation could result in carbon monoxide poisoning or death. The following steps shall be followed for each appliance connected to the venting system being placed into operation, while all other appliances connected to the venting system are not in operation:. Seal any unused openings in the venting system. 2. Inspect the venting system for proper size and horizontal pitch, as required in the National Fuel Gas Code, ANSI Z223./NFPA 5 or the CAN/CGA B9 Installation Codes and these instructions. Determine that there is no blockage or restriction, leakage, corrosion and other deficiencies which could cause an unsafe condition. 3. As far as practical, close all building doors and windows and all doors between the space in which the appliance(s) connected to the venting system are located and other deficiencies which could cause an unsafe condition.. Close fireplace dampers. 5. Turn on clothes dryers and any appliance not connected to the venting system. Turn on any exhaust fans, such as range hoods and bathroom exhausts, so they are operating at maximum speed. Do not operate a summer exhaust fan. 6. Follow the lighting instructions. Place the appliance being inspected into operation. Adjust the thermostat so appliance is operating continuously. 7. If improper venting is observed during any of the above tests, the venting system must be corrected in accordance with the National Fuel Gas Code, ANSI Z22./NFPA 5 and/or CAN/CGA B9 Installation Codes. 8. After it has been determined that each appliance connected to the venting system properly vents where tested as outlined above, return doors, windows, exhaust fans, fireplace dampers and any other gas-fired burning appliance to their previous conditions of use. The cabinet must have an uninterrupted or unbroken ground according to National Electrical Code, ANSI/NFPA 70 - latest edition and Canadian Electrical Code, CSA C22. or local codes to minimize personal injury if an electrical fault should occur. A failure to follow this warning could result in an electrical shock, fire, injury, or death. CAUTION The integrated furnace control is polarity sensitive. The hot leg of the 5 VAC power must be connected to the BLACK field lead. FIRE OR EXPLOSION HAZARD Failure to follow the safety warnings exactly could result in serious injury, death or property damage. Never test for gas leaks with an open flame. Use a commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property damage, personal injury, or loss of life. FIRE OR EXPLOSION HAZARD Failure to follow the safety warnings exactly could result in serious injury, death or property damage. Improper servicing could result in dangerous operation, serious injury, death, or property damage. SEQUENCE OF OPERATION THERMOSTAT CALL FOR HEAT R and W thermostat contacts close signaling the control module to run its self-check routine. After the control module has verified that the pressure switch contacts are open and the limit switch(es) contacts are closed, the draft blower will be energized. As the induced draft blower comes up to speed, the pressure switch contacts will close and the ignitor warm up period will begin. The ignitor will heat for approx. 7 seconds, then the gas valve is energized to permit gas flow to the burners. The flame sensor confirms that ignition has been achieved within the second ignition trial period. After the flame sensor confirms that ignition has been achieved, the delay to fan ON period begins timing and after approx. 5 seconds the indoor blower motor will be energized and will continue to run during the heating cycle. When the thermostat is satisfied, R and W thermostat contacts open, the gas valve will close, the flames will extinguish, and the induced draft blower will be de-energized. The indoor blower motor will continue to run for the fan off period (Field selectable at 60, 00, 0 or 80 seconds), then will be de-energized by the control module. M80-SF-C
. GENERAL INSPECTION Examine the furnace installation annually for the following items: a. All flue product carrying areas external to the furnace (i.e. chimney, vent connector) are clear and free of obstruction. A vent screen in the end of the vent (flue) pipe must be inspected for blockage annually. b. The vent connector is in place, slopes upward and is physically sound without holes or excessive corrosion. c. The return air duct connection(s) is physically sound, is sealed to the furnace and terminates outside the space containing the furnace. d. The physical support of the furnace should be sound without sagging, cracks, gaps, etc., around the base so as to provide a seal between the support and the base. e. There are no obvious signs of deterioration of the furnace. 2. FILTERS Filters should be cleaned or replaced (with high velocity filters only), monthly and more frequently during high use times of the year such as midsummer or midwinter. 3. BLOWERS The blower size and speed determine the air volume delivered by the furnace. The blower motor bearings are factory lubricated and under normal operating conditions do not require servicing. If motor lubrication is required it should only be done by a qualified servicer. Annual cleaning of the blower wheel and housing is recommended for maximum air output, and this must be performed only by a qualified servicer or service agency.. IGNITER This unit has a special hot surface direct ignition device that automatically lights the burners. Please note that it is very fragile and should be handled with care. Do not touch igniter. It is extremely hot. Failure to follow this warning could result in severe burns. 5. BURNER Gas burners do not normally require scheduled servicing, however, accumulation of foreign material may cause a yellowing flame or delayed ignition. Either condition indicates that a service call is required. For best operation, burners must be cleaned annually using brushes and vacuum cleaner. Turn off gas and electric power supply. To clean burners, remove the top burner bracket. Lift burners from orifices. NOTE: Be careful not to break igniter when removing burners. Clean burners with brush and/or vacuum cleaner. Reassemble parts by reversal of the above procedure. NOTE: On LP (propane) units, some light yellow tipping of the outer mantle is normal. Inner mantle should be bright blue. Natural gas units should not have any yellow tipped flames. This condition indicates that a service call is required. For best operation, burners must be cleaned annually using brushes and vacuum cleaner. PERIODIC SERVICING REQUIREMENTS Service Facts NOTE: On LP (propane) units, due to variations in BTU content and altitude, servicing may be required at shorter intervals. CARBON MONOXIDE POISONING HAZARD Failure to follow the installation instructions for the venting system being placed into operation could result in carbon monoxide poisoning or death. 6. HEAT EXCHANGER/FLUE PIPE These items must be inspected for signs of corrosion, and/or deterioration at the beginning of each heating season by a qualified service technician and cleaned annually for best operation. To clean flue gas passages, follow recommendations below: a. Turn off gas and electric power supply. b. Inspect flue pipe exterior for cracks, leaks, holes or leaky joints. c. Remove burner compartment door from furnace. d. Inspect around insulation covering flue collector box. Inspect induced draft blower connections to the flue pipe connection. e. Remove burners. (See.) f. Use a mirror and flashlight to inspect interior of heat exchanger, be careful not to damage the igniter, flame sensor or other components. g. If any corrosion is present, contact a service agency. Heat exchanger should be cleaned by a qualified service technician. h. After inspection is complete replace burners and furnace door. i. Restore gas supply. Check for leaks using a soap solution. Restore electrical supply. Check unit for normal operation. FIRE OR EXPLOSION HAZARD Failure to follow the safety warnings exactly could result in serious injury, death or property damage. Never test for gas leaks with an open flame. Use a commercially available soap solution made specifically for the detection of leaks to check all connections. A fire or explosion may result causing property damage, personal injury, or loss of life. 7. COOLING COIL CONDENSATE DRAIN If a cooling coil is installed with the furnace, condensate drains should be checked and cleaned periodically to assure that condensate can drain freely from coil to drain. If condensate cannot drain freely water damage could occur. (See Condensate Drain in Installer s Guide) CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. M80-SF-C 5
UPFLOW WIRING DIAGRAM From Dwg. D39 (continued on next page) 6 M80-SF-C
UPFLOW SCHEMATIC DIAGRAM From Dwg. D39 M80-SF-C 7
DOWNFLOW WIRING DIAGRAM From Dwg. D395 (continued on next page) 8 M80-SF-C
DOWNFLOW SCHEMATIC DIAGRAM Service Facts From Dwg. D395 M80-SF-C 9
FURNACE AIRFLOW (CFM) VS. EXTERNAL STATIC PRESSURE (IN. W.C.) MODEL SPEED TAP 0.0 0. 0.30 0.0 0.50 0.60 0.70 0.80 0.90 M80P00AU2AA -HIGH - Black -LOW - Red 08 87 76 67 00 832 70 599 982 809 678 575 950 779 68 5 90 72 60 507 860 697 585 63 802 6 52 3 763 585 52 357 660 57 38 29 M80P060AU2AA -HIGH - Black -LOW - Red 08 835 72 6 997 82 702 596 973 800 683 573 9 77 655 53 90 73 67 505 852 689 57 59 796 636 56 06 73 575 52 35 659 506 379 277 M80P060AU36AA -HIGH - Black -LOW - Red 26 23 02 900 389 225 039 903 35 97 027 895 298 60 005 877 236 3 973 88 7 057 93 809 099 99 879 760 0 96 87 700 93 83 75 629 M80P080BU36AA -HIGH - Black -LOW - Red 393 20 06 900 38 9 052 903 36 98 07 895 335 77 033 888 296 7 008 869 27 07 973 82 89 058 928 808 999 873 766 02 930 808 77 M80P080BU8AA -HIGH - Black -LOW - Red 839 323 092 788 82 325 090 783 796 329 09 780 756 39 083 768 70 308 076 758 6 275 059 737 573 26 00 79 80 005 67 392 65 970 630 M80P00BU36AA -HIGH - Black -LOW - Red 76 29 0 873 6 257 06 887 252 058 890 08 23 050 883 363 3 028 86 307 58 990 83 2 0 936 79 63 030 866 72 07 96 780 680 M80P00CU8AA -HIGH - Black -LOW - Red 880 662 28 8 86 635 2 25 799 598 02 20 70 55 370 93 669 93 326 6 595 2 269 2 89 35 99 073 38 256 7 009 260 57 022 935 M80P00CU60AA -HIGH - Black -LOW - Red 28 908 62 3 23 888 609 9 20 868 597 395 53 83 582 38 0 800 567 367 929 75 533 335 856 690 98 302 766 63 38 256 676 572 377 9 M80PDU60AA -HIGH - Black -LOW - Red 235 906 66 23 20 88 632 5 66 856 67 07 36 87 596 39 05 777 575 375 923 72 535 338 80 67 9 300 750 602 27 26 659 533 360 92 M80P0DU60AA -HIGH - Black -LOW - Red 262 228 755 50 207 22 76 6 235 96 736 2 228 5 79 27 226 2 702 23 99 656 383 69 887 609 35 989 797 56 298 908 706 58 2 CFM VS. TEMPERATURE RISE CFM (CUBIC FEET PER MINUTE) MODEL 500 600 700 800 900 000 00 0 300 00 500 600 700 800 900 00 200 20 2300 200 M80P00AU2AA 5 9 2 37 33 30 M80P060AU2AA 63 56 9 M80P060AU36AA 56 9 0 37 3 32 M80P080BU36AA 59 5 9 6 2 M80P080BU8AA 67 62 57 53 9 M80P00BU36AA 58 52 9 6 2 0 37 35 33 M80P00CU8AA 67 62 57 53 9 6 39 37 M80P00CU60AA 62 57 53 9 6 39 37 35 3 32 3 M80PDU60AA 59 56 52 9 7 2 0 M80P0DU60AA 69 65 6 58 55 52 9 7 5 0 M80-SF-C
FURNACE AIRFLOW (CFM) VS. STATIC PRESSURE (ins. w.g.) MODEL SPEED TAP 0.0 0. 0.30 0.0 0.50 0.60 0.70 0.80 0.90 M80P060AD2AA -HIGH - Black -LOW - Red 0 025 838 722 55 988 808 689 95 779 656 056 905 72 68 00 859 70 579 92 797 66 528 88 735 588 78 77 66 502 376 70 558 5 275 M80P060AD36AA -HIGH - Black -LOW - Red 80 302 5 956 29 276 00 97 375 229 070 98 38 88 035 888 282 000 859 00 088 965 82 2 02 98 788 029 953 859 7 959 882 790 682 M80P080BD5AA -HIGH - Black -LOW - Red 798 38 20 005 750 367 50 970 692 333 08 808 62 300 075 775 575 275 02 767 500 233 008 733 25 92 967 700 325 2 925 675 225 083 867 67 M80P00CD8AA -HIGH - Black -LOW - Red 965 65 07 2 95 627 398 8 865 605 387 5 805 575 375 95 70 535 37 66 670 82 38 0 587 2 275 05 500 330 90 05 370 2 095 970 M80P00CD60AA -HIGH - Black -LOW - Red 265 962 705 92 23 927 688 67 60 89 67 2 995 839 636 929 786 600 385 82 72 57 36 755 662 92 307 67 58 35 23 593 500 377 79 M80PDD60AA -HIGH - Black -LOW - Red 22 98 72 76 22 962 705 66 263 92 688 56 206 90 67 0 9 866 653 23 979 805 6 392 908 73 569 36 80 680 55 302 700 67 6 23 M80P0DD60AA -HIGH - Black -LOW - Red 2377 25 806 527 232 8 793 507 2265 6 779 86 299 992 738 73 233 938 696 59 50 872 655 22 967 805 6 38 877 727 556 329 786 69 97 273 CFM VS. TEMPERATURE RISE MODEL 700 800 900 000 00 0 300 00 500 600 700 800 900 00 200 20 2300 200 M80P060AD2AA 63 56 9 0 M80P060AD36AA 56 9 0 37 3 32 M80P080BD5AA 6 57 52 8 M80P00CD8AA 62 57 53 9 6 39 37 M80P00CD60AA 62 57 53 9 6 39 37 35 3 32 3 M80PDD60AA 59 56 52 9 7 2 0 M80P0DD60AA 69 65 6 58 55 52 9 7 5 AIRFLOW ADJUSTMENT Check inlet and outlet air temperatures to make sure they are within the ranges specified on the furnace rating nameplate. If the airflow needs to be increased or decreased, see the wiring diagram for information on changing the speed of the blower motor. Disconnect power to the unit before removing the blower door. Failure to follow this warning could result in personal injury from moving parts. This unit is equipped with a blower door switch which cuts power to the blower and gas valve causing shutdown when the door is removed. Operation with the door removed or ajar can permit the escape of dangerous fumes. All panels must be securely closed at all times for safe operation of the furnace. INDOOR BLOWER TIMING Heating: The control module controls the indoor blower. The blower start is fixed at 5 seconds after ignition. The FAN-OFF period is field selectable by dip switches at 60, 00, 0, or 80 seconds. The factory setting is 00 seconds (See wiring diagram). Cooling: The fan delay off period is factory set at 0 seconds. The option for 80 second delay off is field selectable (See wiring diagram). NOTE: drive motors have bearings which are permanently lubricated and under normal use, lubrication is not recommended. M80-SF-C
CONDITIONS AFFECTING UNIT PERFORMANCE. EXCESSIVE COMBUSTION VENT PRESSURE OR FLUE BLOCKAGE If pressure against the induced draft blower outlet becomes excessive, the pressure switch will shut off the gas valve until acceptable combustion pressure is again available. 2. LOSS OF FLAME OR GAS SUPPLY FAILURE If loss of flame occurs during a heating cycle (when flame is not present at the sensor), the control module will retry the ignition sequence up to two times after the sensor cools. If ignition is not achieved, it will lockout the furnace. 3. POWER FAILURE If there is a power failure during a heating cycle, the system will restart the ignition sequence automatically when power is restored, if the thermostat still calls for heat.. INDUCED DRAFT BLOWER FAILURE If pressure is not sensed by the pressure switch, it will not allow the gas valve to open, therefore the unit will not start. If failure occurs during a running cycle, the pressure switch will cause the gas valve to close and shut the unit down. The following warning complies with State of California law, Proposition 65. This product contains fiberglass wool insulation! Fiberglass dust and ceramic fibers are believed by the State of California to cause cancer through inhalation. Glasswool fibers may also cause respiratory, skin, or eye irritation. PRECAUTIONARY MEASURES Avoid breathing fiberglass dust. Use a NIOSH approved dust/mist respirator. Avoid contact with the skin or eyes. Wear long-sleeved, loose-fitting clothing, gloves, and eye protection. Wash clothes separately from other clothing: rinse washer thoroughly. Operations such as sawing, blowing, tear-out, and spraying may generate fiber concentrations requiring additional respiratory protection. Use the appropriate NIOSH approved respirator in these situations. FIRST AID MEASURES Eye Contact Flush eyes with water to remove dust. If symptoms persist, seek medical attention. Skin Contact Wash affected areas gently with soap and warm water after handling. Fault LED Flash Codes Definitions INTERGRATED FURNACE CONTROL ERROR FLASH CODES Flashing Slow --- Flashing Fast --- Continuous ON --- Continuous OFF --- rmal - call for Heat rmal - Call for Heat Replace IFC Check Power 2 Flashes --- System Lockout (Retries or Recycles exceeded) 3 Flashes --- Pressure Switch Error Flashes --- Open High Limit Device 5 Flashes --- Flame sensed when no flame should be present 6 Flashes --- 5 Volt AC power reversed or Poor Grounding 7 Flashes --- Gas valve circuit error 8 Flashes --- Low flame sense signal Ingersoll Rand 89 N. Pennsylvania Street Carmel, IN 6032 For more information contact your local dealer (distributor) The manufacturer has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.