Chapter contents Separator for ground installation Ground installation Basic design up to load class: D 400 With direct suction for disposal without odour build-up With direct suction and high-pressure interior cleaning for disposal without odour build-up and simultaneous cleaning of the container. for freestanding installation With complete disposal Mobile separator for food stall or marquee Basic design for disposal via the cover Extension stage 1 for disposal via direct suction Extension stage 2 with manual high-pressure interior cleaning and optional disposal pump for disposal without odour build-up Extension stage 3 with automatic high-pressure interior cleaning and optional disposal pump and remote control for disposal without odour build-up Available in oval curved or split design for optimal installation With partial disposal Optionally available in manual or automatic design. Informations General informations...424 Dimensioning according EN 1825-2..430 423
j Planning references Separator General information The applications The industrial sources of waste water must ensure through appropriate pretreatment facilities that substances and liquids, which spread noxious fumes and nuisance odours, affect building materials and drainage systems or interfere with the operation, will not enter public pipes. In establishments where grease-containing waste water accumulates, grease traps according to EN 1825/DIN 4040-0 must be installed to guarantee the retention of greases and oils of an organic origin from the waste water. This applies, for example, for kitchen operations and meat processing plants. A double lifting plant or complete pumping station must be provided after each grease separator that is installed below the backflow level (generally the street level). The individual requirements placed on grease separators, lifting plants and complete pumping stations require adjustable product in various s and materials. ACO Haustechnik had an extensive product range of grease separators, lifting plants and complete pumping stations for the ground installation and free-standing installation for decades. The standards and tests All grease separators by ACO Haustechnik are produced according to the applicable standards EN 1825 and DIN 4040-0. The grease separators listed in the product range are hydraulically tested and have a general official approval, i.e. the new application permit from DIBt Berlin. The separator systems furthermore are subject to a routine inspection by the Landesgewerbeanstalt Bayern that checks the separator production for the adherence to the currently applicable test standards. The application scope Butcher shops with and without slaughter Slaughterhouses (large-scale slaughterhouses) Meat and sausage factories, with or without slaughter Utilisation of animal carcasses Poultry slaughterhouses Bowel preparation facilities Hotels Restaurants Food distribution points with return tableware Cafeterias Interstate service areas Cafeterias Kitchens in hospitals Canneries Cooking oil refineries Ready-meals manufacturer Peanut roasters Grilling, frying and deep frying kitchens Fries and chips products Principles and function A grease separator operates purely physical according to the gravity principle (density difference), i.e. heavy waste. water components sink to the bottom, light material such as animal oils and fats rise to the top in the separator. The sediments in the sludge trap and the grease layer are selectively destroyed at up to 175 bar by the high pressure jet of the special orbital cleaning head and homogenized capable of pumping. Depending on the location of the installation site, the separator content can be pumped to the disposal vehicle via an on-site permanently installed line or be further transported with an optional disposal pump. Function diagram of the grease separator according to EN 1825 424
Separator Planning references Installation When install in the ground and when in the building? There are two installation situations for grease separators: Free standing grease separators and grease separators for underground installation. Precondition for easy disposal, maintenance and cleaning of the grease separator is a readily accessible installation location. In addition, always verify that the pipe between the accumulation point the grease containing waste water and grease separator is kept as short as possible. Furthermore, the installation may not be done in unventilated rooms or in traffic or storage areas. The setup may not be made in the vicinity of living quarters. The most important criteria that must be considered when choosing between a freestanding or underground installation are discussed in the following. Installation in the ground Installation in green spaces Manhole covers must be odour sealed. A manhole cover of Load class A 15 is sufficient. Recommendation: The location where the disposal vehicle is parked should be attached. Access routes Installation possibly outside the directly accessed area. Odour sealed manhole covers of Load class B 125 are generally sufficient. When installing directly in the roadway, a Load class D 400, odoursealed, must be provided. Courtyards Critical installation points Courtyards are critical in reference to odours during the operation and disposal: 1. During operation, odours due to loosely attached, manhole covers that are not odour sealed are possible. 2. Strong odours when opening the manhole covers during disposal. Solution Equipping the separators with a so-called direct suction. Installing the suction pipe in the ground, for example, on an exterior wall of the building, easily accessible for the disposal vehicle. Suction line preferably made of PE-HD pressure pipe minimum 6-PN 65/80 DN. The disposal via direct extraction has the distinct advantage that the manhole cover remains closed during the first suctioning process, so that an odour will not develop. The manhole covers are not opened until rinsing the disposal shaft with pressurized water from the disposal vehicle. Since the separator chamber has already been emptied by suction, the fumes were also partially extracted, so that only minimal odours occur. If the disposal vehicle is equipped with a functioning carbon filter for the tank exhaust, there will hardly be any complaints from the affected residents. 425
Planning references Separator Installation in buildings The installation in buildings has increased over the past 15 years. Reasons for this are that, for example, barely any open spaces are available for the underground installation due to renovations of old buildings, changes of use of existing buildings and naturally also due to the high by the high building density. s are installed in the immediate vicinity of the waste water accumulation point (EN 1825-2). Installation room The installation room must be separate, dry and provided with a functioning ventilation system. The installation area of the grease separator must be level. The waste water should be transported to the grease separator at a free drop of at least 1:50. Pumps in front of the grease separators have the serious disadvantage that grease and waste water are thoroughly mixed, the separation is hampered, and limit violations are inevitable. If unavoidable due to structural conditions, these disadvantages can be almost eliminated by using a special lifting plant with displacement pumps. The connection between the access road, installation and design The access routes to the installation room must also be observed in the free-standing installation. In order to select the proper separator, which can also be installed via stairways, winding corridors or light wells, the conditions on-site must be known. Various designs allow an installation as needed. Oval structure Adjusted to current door dimensions Separator of stainless steel NS 1 4: max. width 760 mm NS 5.5 : max. width 1,0 mm Separator of polyethylene NS 1 4: max. width 770 mm NS 5.5 : max. width 1,020 mm such as Eco-Jet OD Round structure Can be knocked down into single segments For example, recommend for access routes with a right angle Adaptation of the NS subsequently on-site is possible by exchanging centre segments (e.g. from NS 7 to NS ) Number of segments: NS 2 4: 2 segments, Ø 1,000 mm NS 7 : 3 segments, Ø 1,500 mm NS 15 20: 3 segments, Ø 1,750 mm such as Lipurat-RS divided structure Particularly suitable for renovations with narrow insertion openings Can be dismantled into 3 segments Max. segment dimensions (LxWxH): NS 2: 670 x 700 x 1,360 mm NS 4: 1,140 x 700 x 1,360 mm such as Eco-Jet G/GD Construction site welding For extreme installations (narrow stairways, elevator shafts) is delivered in single parts, welded and checked for leaks on-site such as Fapurat-PE-OAE 426
Separator Planning references Installation below the backflow level, lifting plant for grease separator The drainage via a double lifting plant must be guaranteed when installing the grease separator below the backflow level. The top edge of the street (curb) typically forms the backflow level for grease separators, which are installed in the basement. Almost every grease separator must therefore be drained via a double lifting plant. This should be strictly observed, especially in case of free-standing separators in buildings, even if only an occasional backflow risk exists. Lifting plant Vent pipe (separate over the roof) Backflow loop "Separators for greases with the static water level below the backflow level (see EN 752-1), must be drained via a lifting plant downstream." (Excerpt from EN 1825-2, Sec 7.3) The grease separator is only suitable and approved for a pressure-free operation. Odour sealed does not mean backflow secure! When selecting the lifting plant, it must be noted that a double lifting plant is installed (regulation in the industrial and commercial sector) to ensure an uninterrupted operation in case of a pump failure. It is also important to note that a second Function of the air bubble injection Air is continuously blown into the pitot tube via a compressor. The rising air bubbles at the end of the pitot tube provide a constant movement below the pitot tube, so that float cover forming media cannot settle (such as residual grease from the separator). This guarantees is very reliably working level measurement. separation of the grease constituents can occur in the waste water after each grease separator, which would result in deposits in the lifting plant tank. Routine inspections of lifting plant in conjunction with the grease separator maintenance are therefore necessary. These grease deposits also affect the components of the level measurement, such as the float switch, the ball float switch and pitot tubes with a small cross-section negatively. Level measurements with a large dimensioned Pitot tube cross-section with air bubble injection for self-cleaning must be installed. 427
Planning references Separator Additional information for routing, operation and maintenance Routing, ventilation (EN 1825-2) When installing the inlet pipe through unheated or open-access areas with a frost risk, this section must be equipped with an additional pipe heater (e.g., self-regulating heating tapes and insulation). Inlet pipes require a careful design and installation, since the separator efficiency can already be positively or negatively affected here. Vertical inlet pipes must be designed as follows at the transition to the horizontal pipe, in order to prevent undue turbulence of the waste water and its grease components: Vertical downpipe, 45 bend, straight pipe section of at least 250 mm or more, 45 bend, horizontal piping in the inlet of grease separators at least x DN length long (for example: DN 0 = 1,000 mm, DN 150 = 1,500 mm). Inlet and outlet pipes on grease separators must be sufficiently ventilated. The vent line must be routed up to over the roof for this purpose. (EN 1825-2) More horizontal connecting lines longer than 5m are must also be bled. If the horizontal inlet line has a length of more than m and no other additional ventilated connecting lines, the inlet pipe must be provided by an additional vent line directly near the separator inlet. (EN 1825-2) 428
Separator Planning references Sampling Pros and cons of sampling shafts/ sampling pipes for the so-called integrated sampling options in the grease separator: Sampling shafts in underground installation and sampling pipe in the free-standing installation have an open pipe end on the interior of the inlet with a drop of at least 160 mm on the pipe bottom outlet to the channel (see DIN 4040-0, Item 5.5.2). Proper and safe sampling by the authorities is only possible with this arrangement with the recommended wide-mouth bottle with the necessary supervision. Other key advantages of this type, especially in the underground installation, good accessibility to the outlet drain to the channel and that of the grease separator, for inspection, especially for studies with a video camera and for cleaning with the HD-street washer. Only where the drop cannot be realized due to structural conditions or the sampling shaft/sampling pipe are not installed due to the lack of space, the integrated sampling must be tolerated for cost reasons, among others (bottom drop must equal at least 30 mm - DIN 4040-0, item 5.5.2). The use of an integrated sampling equipment must be clarified in advance with the authorities. Disposal (DIN 4040-0, item 12.2) Sludge trap and separator must be completely emptied and cleaned at least once a month, preferably every two weeks. The separators must subsequently be refilled with water (such as drinking water, process water, treated water from the grease separator), which corresponds with the local inlet regulations. General inspection (DIN 4040-0, item 12.4) Excerpt from DIN 4040-0, item 12.4: "Prior to the start-up and periodically thereafter at intervals no longer than 5 years, the separators must be checked by an expert for its proper condition and proper operation after first completely emptying and cleaning." Emphasis in the inspection are primarily the dimensioning of the separator, the structural condition and seal of the separator, the condition of interior walls, fittings, electrical equipment, construction of inlet and ventilation ducts, completeness of the operation log, proof of proper disposal and the availability of required authorizations and documents. Operating log (DIN 4040-0, item 12.5) An operating log must be maintained for each grease separator. The following must be entered in the log: Completed inspections, maintenance, checks and disposals. The operating logs must be stored by the operator and must be presented to the locally responsible authority upon request. Application limits Excerpts: "Materials that could affect the separator system, such as chopped coarse materials and solids, including the waste water contents from wet disposal systems, cannot be discharged. " (Excerpt DIN 4040-0, Item.1) "The targeted use of biological active agents, e.g. enzyme-containing products for converting fatty substances, or the socalled self-cleaning is not acceptable. " (Excerpt DIN 4040-0, Item.1) "If detergents, dish soaps, cleansing agents, disinfectants and expedients enter the waste water, they must be separator friendly and may not form stable emulsions. Dish soaps and and cleaning products should not contain or release chlorine. "(Excerpt DIN 4040-0, Item.1) "Grey water, in which a significant share of grease is present in non-separable, i.e. emulsified form, for example from dairies, cheese dairies, fish processing plants or from catering services with a pure rinsing operation, as well as from Waste treatment plants are only effectively treated in grease separators under certain conditions. Another treatment of the waste water may be required." (Excerpt EN 1825-2, item 4) "Systems in which waste water contains the rapidly decaying sediments, e.g. in the fish industry, no sludge trap must be installed, however, these grease separators must be equipped with a strainer or a screen... " (Excerpt from EN 1825-2, Sec 4) Maintenance (DIN 4040-0, item 12.3) The separator must be maintained annually by a competent person according to the manufacturer's specifications. 429
Dimensioning according to EN 1825-2 Separator General information Consignor Telephone Fax Project/installation site Replanning Reconstruction Owner Telephone Fax Offer to Information These records were received on the basis of: Telephone conversation with: Site visit with: Please note required remarks / amendments under clause 6, or on a separate sheet 430
Separator Dimensioning according to EN 1825-2 1. Waste water type and composition 1.1 Where is the waste water from? Boarding facility All-day commercial kitchen Hospital canteens Factory Kitchen / Canteen Hotel kitchen Specialty restaurant 1.2 Waste water contents Sediments Rapidly rotting sediments Fats Which? Density (spec. weight) = [g/cm 3 continuous l/week discontinuous l/week intermittent (e.g. malfunction) l/week Slaughterhouse/ meat processing plant Meat products plant with slaughter Meat products plant without slaughter Butcher shop with slaughter Butcher shop without slaughter Supermarket with processing / sales Poultry abattoir Rinsing and cleaning agents If rinsing and cleaning agents are used, they must be used as sparingly, in order to maintain the separability of the oils and greases as much as possible (observe the dosage amount by the manufacturer). Oil/grease processing operation Margarine factory Oil mill Cooking oil refinery Peanut roaster Fries and chips production Cannery Ready-meals manufacturing Fish processing plant Rendering plant Other waste water contents 2. Inlet conditions Residual grease content max. mg/l measured according to DN 38409 part 17 max. approved temperature at the intake C 3. Dimensioning 3.1 according to kitchen furnishings and discharge valves 3.2 according to food servings in commercial kitchens 3.3 for meat processing plants, sausage production / cutting plants 431
Dimensioning according to EN 1825-2 Separator 3.1 according to kitchen furnishings and discharge valves m Furnishings Quantity n qi [l/s] (n x qi) Simultaneity factor Zi (n) Grey for 1 unit for 2 units for 3 units for 4 units for 5 units water Q s 1 Kettle spout 25 mm... x 1 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 2 Kettle spout 50 mm... x 2 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 3 Tilting kettle outlet 70 mm... x 1 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 4 Tilting kettle outlet 0 mm... x 3 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 5 Sink with odour-seal, 40 mm... x 0,8 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 6 Sink with odour-seal, 50 mm... x 1,5 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 7 Sink without odour-seal, 40 mm... x 2,5 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 8 Sink without odour-seal, 50 mm... x 4 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 9 Dishwasher... x 2 =... l/s x 0.60 x 0.50 x 0.40 x 0.34 x 0.30... l/s Tilting frying pan... x 1 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 11 Frying pan... x 0,1 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s High pressure/steam cleaning 12 equipment... x 2 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 13 Peeling device... x 1,5 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 14 Vegetable washing device... x 2 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s Tap diameter/threaded connection according to DN ISO 228-1 15 DN 15 R ½... x 0,5 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 16 DN 20 R ¾... x 1 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 17 DN 25 R 1... x 1,7 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s Total Q s... l/s Difficulty factor Density (fd) up to 0.94 g/ cm 3 = fd 1,0 more than 0.94 g/cm 3 = fd 1,5 Intake temperature (ft) up to 60 = ft 1,0 over 60 = ft 1,3 Cleaning agents (fr) no = fr 1,0 yes = fr 1,3 fr 1.5 or greater in hospitals Explanation: m = Serial number of the object n = Number of furnishings qi = the maximum grey water outflow in l/s Zi (n) = the factor of concurrency of use NS = NS = Q s x fd x ft x fr Please select the next highest NS! NS = x x x = Selected: NS... 432
Separator Dimensioning according to EN 1825-2 3.2 according to food servings in commercial kitchens Commercial kitchens M= Meals (number) of monthly average of the daily produced hot food portions VM=company-specific water per hot food serving F= Impact load factor in reference to the operating conditions Hotel kitchen... Meals/daily x 0 l =... x 5 =... l Specialty restaurant... Meals/daily x 50 l =... x 8.5 =... l Canteen / cafeteria... Meals/daily x 5 l =... x 20 =... l Hospitals... Meals/daily x 20 l =... x 13 =... l All-day commercial kitchen... Meals/daily x l =... x 22 =... l Commercial kitchens t= daily operating hours in which the separator is charged with grey water Waste water Q s Hotel kitchen =... Litre... Operating hours x 3600 seconds =... l/s Specialty restaurant =... Litre... Operating hours x 3600 seconds =... l/s Canteen / cafeteria =... Litre... Operating hours x 3600 seconds =... l/s Hospitals =... Litre... Operating hours x 3600 seconds =... l/s All-day commercial kitchen =... Litre... Operating hours x 3600 seconds =... l/s Difficulty factor Density (fd) up to 0.94 g/ cm 3 = fd 1,0 more than 0.94 g/cm 3 = fd 1,5 Intake temperature (ft) up to 60 = ft 1,0 over 60 = ft 1,3 Cleaning agents (fr) no = fr 1,0 yes = fr 1,3 fr 1.5 or greater in hospitals NS = Q s x fd x ft x fr Please select the next highest NS! NS = x x x = Selected: NS... 433
Dimensioning according to EN 1825-2 Separator 3.3 Sausage production/cutting operations Sausage production Size of the meat processing plant Small sausage production up to 0 kg daily Medium sausage production 1 to 200 kg daily Large sausage production 201 to 800 kg daily Large animal units, slaughter per week when slaughtering up to 5 cattle or 12.5 pigs each week when slaughtering up to cattle or 25 pigs each week when slaughtering up to 40 cattle or 0 pigs each week M= Sausage production in kg/daily Vp= operational water volume per kg of sausage production... kg / daily x 20 l =...... kg / daily x 15 l =...... kg / daily x l =... Size of the meat processing plant Small sausage production up to 0 kg daily Medium sausage production 1 to 200 kg daily Large sausage production 201 to 800 kg daily F= Impact load factor depending on operating conditions x 30 x 35 x 40 t= daily operating hours in which the separator is charged with grey water Waste water Q s... Litre =.. Operating hours x 3600 seconds Q s =... l/s... Litre =.. Operating hours x 3600 seconds Q s =... l/s... Litre =.. Operating hours x 3600 seconds Q s =... l/s Meat cutting operations without meat and sausage production; grey water mainly accumulates during cleaning m Fitting objects Quantity n qi [l/s] (n x qi) Simultaneity factor Zi (n) Grey for 1 unit for 2 units for 3 units for 4 units for > 5 units water Q s 15 DN 15... x 0,5 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 16 DN 20... x 1 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 17 DN 25... x 1,7 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s 12 High pressure/steam cleaning equipment... x 2 =... l/s x 0.45 x 0.31 x 0.25 x 0.21 x 0.20... l/s Total Q s... l/s Difficulty factor Density (fd) up to 0.94 g/cm 3 = fd 1,0 more than 0.94 g/cm 3 = fd 1,5 Intake temperature (ft) up to 60 = ft 1,0 over 60 = ft 1,3 Cleaning agents (fr) no = fr 1,0 yes = fr 1,3 NS = Q s x fd x ft x fr Please select the next highest NS! NS = x x x = Selected: NS... 434
Separator Dimensioning according to EN 1825-2 4. Content determination of sludge trap Restaurants/ catering facilities; Butchers / meat factories without slaughter, supermarkets, other comparable establishments NS x 0 litres = l Slaughterhouses; Butchers / meat factories with slaughter, other industrial plants with increased sludge NS x 200 litres = l selected content: l 5. Execution of the separator system Separator for Material PE-HD Fittings with direct extraction or with HP interior cleaning manual automatic Control unit Surface mount or Flush Housing: Insulated housing Steel housing other dimensions Replanning: NS or number of meals per day Renovation of existing plant type with waste water lifting plant: delivery head (suction height) geo. m. width DN Length of the disposal pipe: m Number of bends DN 90 /45 Underground installation with cover Load class (A,B,D) Stainless steel (only for free-standing with disposal pump with additional sampling equipment with filling unit Remote control Interior assembly Exterior assembly Pit /assembly area: L x W x H mm Inlet: DN inlet height: mm Frost-free depth mm installation) with inspection window with coarse trap Distance of the control box to the separator m in the building on the property Disposal: Opening L x W mm or diameter mm Stairs / corridor / passage: x W x H mm x B x H mm 6. Comments City, Date Signature Comment: Our recommendations for planning and dimensioning must be generally verified non-binding and by the party responsible for the construction. 435
Section contents for ground installation Separator Ground installation Page complete disposal Compact design polyethylene (HD-PE) Eco-FPI 438 Eco-FPI with direct suction 440 Ground installation Accessories 442 437
complete disposal Compact design polyethylene (HD-PE) Separator Ground installation Eco-FPI Product information Ground installation ACO product advantages Load class up to D 400 (corresponds to SLW 60) without customer-side load distribution Low installation costs - separator, sludge trap, sampling in a container Additional heavy duty crane not necessary Buoyancy safety for a groundwater level of up to max 1 m over base plate Easy cleaning due to curved shape plant in accordance with EN 1825 and DIN 4040 0 For ground installation Ordering information Polyethylene base body (double-walled windable pipe) Reinforced concrete cover plate in accordance with DIN 19537 For NS 1 4: Ø00/625 x 200 mm For NS 7 : Ø1500/625 x 200 mm With integrated sludge trap Inlet and drainage connections in accordance with EN 877 Manhole cover in accordance with EN 124 Without ventilation opening Reference dimensions: 625 mm Screwed odour-tight System ACO Passavant Official approval Z 54.1 411 NS 1 NS 2 NS 3 NS 4 NS 7 NS width Capacity Weight Article No. Sludge trap Grease storage Total capacity B 125 D 400 [l] [l] [l] [kg] DN 0 0 120 615 7 3201.55.00 3201.55.01 DN 0 200 120 715 7 3201.56.00 3201.56.01 DN 0 200 120 715 7 3202.55.00 3202.55.01 DN 0 400 120 915 725 3202.56.00 3202.56.01 DN 0 300 120 815 725 3203.55.00 3203.55.01 DN 0 600 120 1115 760 3203.56.00 3203.56.01 DN 0 400 160 915 725 3204.55.00 3204.55.01 DN 0 800 160 1315 760 3204.56.00 3204.56.01 DN 150 700 400 1950 1540 3207.55.00 3207.55.01 DN 150 1400 400 2660 16 3207.56.00 3207.56.01 DN 150 00 400 2250 1575 32.55.00 32.55.01 DN 150 2000 400 3250 1665 32.56.00 32.56.01 438
Separator Ground installation complete disposal Compact design polyethylene (HD-PE) Ø 600 H 1 ØD T inlet DN... outlet DN... H 2 Ø D 1 Ø D 2 Ground installation inlet DN... outlet DN... Sludge trap H1 H2 D D1 D2 T [l] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 NS 2 NS 3 NS 4 NS 7 NS 0 885 785 1 00 1250 695 200 9 1 00 1250 570 200 9 1 00 1250 570 400 1265 1165 1 00 1250 560 300 1140 40 1 00 1250 685 600 1520 1420 1 00 1250 815 400 1265 1165 1 00 1250 560 800 1775 1675 1 00 1250 560 700 1205 15 160 1500 1800 650 1400 1605 1505 160 1500 1800 650 00 1370 1270 160 1500 1800 685 2000 1940 1840 160 1500 1800 665 439
complete disposal Compact design polyethylene (HD-PE) Separator Ground installation Eco-FPI with direct suction Product information Ground installation ACO product advantages Direct suction enables disposal without odour Load class up to D 400 (corresponds to SLW 60) without customer-side load distribution Low installation costs - separator, sludge trap, sampling in a container Additional heavy duty crane not necessary Buoyancy safety for a groundwater level of up to max 1 m over base plate Easy cleaning due to curved shape plant in accordance with EN 1825 and DIN 4040 0 For ground installation With direct suction DN 80/PN inc. flange/flange connection and Storz coupling 75 B Polyethylene base body (double-walled windable pipe) Reinforced concrete cover plate in accordance with DIN 19537 For NS 1 4: Ø00/625 x 200 mm For NS 7 : Ø1500/625 x 200 mm With integrated sludge trap Inlet and drainage connections in accordance with EN 877 Manhole cover in accordance with EN 124 Without ventilation opening Reference dimensions: 625 mm Screwed odour-tight System ACO Passavant Official approval Z 54.1 411 Ordering information NS 1 NS 2 NS 3 NS 4 NS 7 NS width Capacity Weight Article No. Sludge trap Grease storage Total capacity B 125 D 400 [l] [l] [l] [kg] DN 0 0 120 615 7 3201.55. 3201.55.11 DN 0 200 120 715 7 3201.56. 3201.56.11 DN 0 200 120 715 7 3202.55. 3202.55.11 DN 0 400 120 915 725 3202.56. 3202.56.11 DN 0 300 120 815 725 3203.55. 3203.55.11 DN 0 600 120 1115 760 3203.56. 3203.56.11 DN 0 400 160 915 725 3204.55. 3204.55.11 DN 0 800 160 1315 760 3204.56. 3204.56.11 DN 150 700 400 1950 1540 3207.55. 3207.55.11 DN 150 1400 400 2660 16 3207.56. 3207.56.11 DN 150 00 400 2250 1575 32.55. 32.55.11 DN 150 2000 400 3250 1665 32.56. 32.56.11 440
Separator Ground installation complete disposal Compact design polyethylene (HD-PE) Ø 600 H 1 ØD T inlet DN... outlet DN... H 2 Ø D 1 Ø D 2 Ground installation inlet DN... 45 outlet DN... Sludge trap H1 H2 D D1 D2 T [l] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 NS 2 NS 3 NS 4 NS 7 NS 0 885 785 1 00 1250 695 200 9 1 00 1250 570 200 9 1 00 1250 570 400 1265 1165 1 00 1250 560 300 1140 40 1 00 1250 685 600 1520 1420 1 00 1250 815 400 1265 1165 1 00 1250 560 800 1775 1675 1 00 1250 560 700 1205 15 160 1500 1800 650 1400 1605 1505 160 1500 1800 650 00 1370 1270 160 1500 1800 685 2000 1940 1840 160 1500 1800 665 441
complete disposal Compact design polyethylene (HD-PE) Separator Ground installation Accessories T = 575-1300 Ø620 Ø565 Designation compatible with Description Article No. Sampling shaft DN 0 Eco-FPI for ground installation NS 1 4 Starch separator Eco-STP for ground installation NS 0.5 1 Curator/Coalisator GG NS 1.5 3 Plastic, material: polyethylene For installation behind the separating plants for ground installation With BEGU cover Clear diameter: 450 mm Load class: D 400 Odour tight Weight: 128 kg Gradient: 33 mm 3300.13.11 186 h Gradient: 153 mm 3300.13. 625 Ground installation T = 575-1300 Ø620 Ø565 Sampling shaft DN 150 Eco-FPI for ground installation NS 7 Starch separator Eco-STP for ground installation NS 2 Curator/Coalisator GG NS 6 Plastic, material: polyethylene For installation behind the separating plants for ground installation With BEGU cover Clear diameter: 450 mm Load class: D 400 Odour tight Weight: 128 kg Gradient: 75 mm 3300.13.21 185 h Gradient: 159 mm 3300.13.20 645 Spannring Verlängerungsstück Dichtung Ø625 Ø865 Ø625 Ø865 Ø625 Ø865 Ø490 Ø434 Ø450 45 650 60 80 0 Extension Supporting ring Supporting ring Supporting ring Sampling shaft Eco-FPI for ground installation Starch separator Eco-STP for ground installation Eco-FPI for ground installation Starch separator Eco-STP for ground installation Eco-FPI for ground installation Starch separator Eco-STP for ground installation Plastic, material: polyethylene For fitting on the protruding sampling shaft for deepened installation Structure height: 0 650 mm (can be shortened every 45 mm by cutting along the markings) Weight: 11 kg Concrete Diameter: 625 mm Starch 60 mm Without sealing Not displaceable Height: 60 mm without mortar joint 70 mm with mortar joint Weight: 50 kg Concrete Diameter: 625 mm Starch 80 mm Without sealing Not displaceable Height: 80 mm without mortar joint 90 mm with mortar joint Weight: 60 kg Concrete Diameter: 625 mm Starch 0 mm Without sealing Not displaceable Height: 0 mm without mortar joint 1 mm with mortar joint Weight: 70 kg 3300.13.00 8700.20.00 8700.20. 8700.20.20 442
Separator Ground installation complete disposal Compact design polyethylene (HD-PE) Designation compatible with Description Article No. Ø00 Ø1240 Ø00 Ø1240 Ø00 Ø1240 Ø1500 Ø1800 Ø1500 Ø1800 500 250 00 500 250 Shaft ring Shaft ring Shaft ring Shaft ring Shaft ring Lattice grating Eco-FPI for ground installation NS 1 4 Starch separator Eco-STP for ground installation NS 0.5 1 Eco-FPI for ground installation NS 1 4 Starch separator Eco-STP for ground installation NS 0.5 1 Eco-FPI for ground installation NS 1 4 Starch separator Eco-STP for ground installation NS 0.5 1 Eco-FPI for ground installation NS 7 Starch separator Eco-STP for ground installation NS 2 Eco-FPI for ground installation NS 7 Starch separator Eco-STP for ground installation NS 2 Eco-FPI NS 1 4 Starch separator Eco-STP NS 0.5 1 Concrete in accordance with DIN 4034 part 1 Diameter: 1,000 mm Starch 250 mm With sealing With socket Without spur Height: 250 mm without mortar joint 265 mm with mortar joint Weight: 240 kg Concrete in accordance with DIN 4034 part 1 Diameter: 1,000 mm Starch 500 mm With sealing With socket Without spur Height: 500 mm without mortar joint 515 mm with mortar joint Weight: 500 kg Concrete in accordance with DIN 4034 part 1 Diameter: 1,000 mm Starch 1,000 mm With sealing With socket Without spur Height: 00 mm without mortar joint 15 mm with mortar joint Weight: 00 kg Concrete in accordance with DIN 4034 part 1 Diameter: 1,500 mm Starch 250 mm With sealing With socket Without spur Height: 250 mm without mortar joint 265 mm with mortar joint Weight: 480 kg Concrete in accordance with DIN 4034 part 1 Diameter: 1,500 mm Starch 500 mm With sealing With socket Without spur Height: 500 mm without mortar joint 515 mm with mortar joint Weight: 931 kg For buoyancy safeguard Reinforcement of the base plate Not upgradeable 8700.42.21 8700.42.31 8700.42.61 8700.42.23 8700.42.33 0150.05.22 Ground installation Lattice grating Eco-FPI NS 7 Starch separator Eco-STP NS 2 For buoyancy safeguard Reinforcement of the base plate Not upgradeable 0150.05.23 Ø250 LW Ø 350 0 Street cap Eco-FPI with direct suction Manhole cover in accordance with EN 124/DIN 1229 Load class: A 15 Cast iron frame and cover Diameter: 300 mm Clear diameter: 250 mm Weight: kg 5354.00.00 443
Hinweis: @@ Dies ist eine Infobox-VORLAGE Zubehör AAAAA Seite xxx. Zubehör BBBBB Seite xxx. Infobox
Section contents for free-standing installation Separator Page mobile use Polyethylene (LLDPE) Stainless steel (material grade 316) Eco-Mobil Typ 0.3l 446 Eco-Mobil Typ 0.5 447 Lipu-Mobil 448 Accessories 449 Eco-Jet-O basic design 450 Oval shape Eco-Jet-OD extension stage 1 452 Hydrojet-OS extension stage 2 454 polyethylene (HD-PE) Hydrojet-OSE extension stage 2/disposal pumps 456 Hydrojet-OA extension stage 3 458 Hydrojet-OAE extension stage 3/disposal pumps 460 Eco-Jet-R basic design 462 complete disposal Curved shape polyethylene (HD-PE) Oval shape stainless steel (material grade 316) Eco-Jet-RD extension stage 1 464 Hydrojet-RS extension stage 2 466 Hydrojet-RSE extension stage 2/disposal pumps 468 Hydrojet-RA extension stage 3 470 Hydrojet-RAE extension stage 3/disposal pumps 472 Accessories 474 Lipurex-O basic design 478 Lipurex-OD extension stage 1 480 Lipurat-OS extension stage 2 482 Lipurat-OSE extension stage 2/disposal pumps 484 Lipurat-OA extension stage 3 486 Lipurat-OAE extension stage 3/disposal pumps 488 Lipurex-R basic design 490 Curved shape stainless steel (material grade 316) Lipurex-RD extension stage 1 492 Lipurat-RS extension stage 2 494 Lipurat-RSE extension stage 2/disposal pumps 496 Lipurat-RA extension stage 3 498 Lipurat-RAE extension stage 3/disposal pumps 500 Accessories 502 Divided shape polyethylene (HD-PE) Eco-Jet-G basic design 506 Eco-Jet-GD extension stage 1 507 Accessories 508 partial disposal Stainless steel (material grade 304) Lipator manual operation 5 Lipatomat automatic control 512 Accessories 514 system solution Suspension equipment Upstream container mono 516 Upstream container duo 518 Accessories 520 445
mobile use Polyethylene (LLDPE) Separator Eco-Mobil type 0.3 Product information Area of application: Mobile food stalls Mobile dishwasher Occasional food preparation Application possible only with Connection of 1 commercial dishwasher with a minimum cleaning time of 1 minute, and a changeover time of ½ minute. (cycle time t z = 1½ min.) Water consumption of the commercial dishwasher after rinsing v s = 5 l In addition to the dishwasher, connection of a maximum of 1 pre-wash unit (short-term) Polyethylene, material LLDPE For mobile rinsing devices (no fixed installation) With integrated sludge trap For free-standing installation in frostprotected areas Plug cap Polyethylene Diameter: 350 mm System ACO Passavant Official approval: Z 54.6 316 Ordering information maintenance opening Ø 350 moulded-in grip 280 width DN 50 475 250 370 485 double socket and socket plug DN 50 Capacity Weight Article No. Sludge trap Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] DN 50 9 32 9,75 42 3700.01.00 inlet DN 50 585 outlet DN 50 Accessories Designation compatible with Description Article No. 70 Inlet valve DN 50 Eco-Mobil Muli-Mini PVC DN 50 With sealing ring in accordance with DIN 19538 0175.18.33 Ø50 Ø62 91 230 385 720 620 Rolls frame Eco-Mobil and Lipu-Mobil Stainless steel, material grade 316 With 4 transport casters Weight: 19 kg 0153.20.81 446
Separator mobile use Polyethylene (LLDPE) Eco-Mobil type 0.5 Product information Area of application: Mobile food stalls Mobile dishwasher Occasional food preparation Application possible only with Connection of 1 commercial dishwasher with a minimum cleaning time of 1 minute, and a changeover time of ½ minute. (cycle time t z = 1½ min.) Water consumption of the commercial dishwasher after rinsing v s = 5 l In addition to the dishwasher, connection of a maximum of 1 pre-wash unit (short-term) Polyethylene, material LLDPE For mobile rinsing devices (no fixed installation) With integrated sludge trap For free-standing installation in frostprotected areas Plug cap Polyethylene Diameter: 450 mm System ACO Passavant Official approval @@ Ordering information DN 0 DN 70 Wartungsöffnung DN 450 620 500 550 785 (Behälter) Zulauf DN... width Capacity Weight Article No. Sludge trap Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] DN 70/0 50 20 0 19 119 3700.02.00 Accessories 140 Designation compatible with Description Article No. 15 Inlet valve DN 0 Waste water lifting plants Polyethylene grease separator Polyethylene starch separator PVC Construction length: 176 mm Weight: 2.75 kg 0175.13.84 Ø120 Ø1 855 Ø133 80 870 Ablauf DN... 176 447
mobile use Stainless steel (material grade 316) Separator Lipu-Mobil Product information Area of application: Mobile food stalls Mobile dishwasher Application possible only with Connection of 1 commercial dishwasher with a minimum cleaning time of 1 minute, and a changeover time of ½ minute. (cycle time tz = 1½ min.) Water consumption of the commercial dishwasher after rinsing v s = 5 l In addition to the dishwasher, connection of a maximum of 1 pre-wash unit (short-term) Stainless steel, material grade 316 For mobile rinsing devices With integrated sludge trap For free-standing installation in frostprotected areas Cover with clamping ring closure Diameter: 350 mm System ACO Passavant Official approval Z 54.6 316 Ordering information maintenance opening Ø 300 DN 50 280 inlet DN 50 475 250 370 385 430 outlet DN 50 585 width Capacity Weight Article No. Sludge trap Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] DN 50 9 32 20 52 7301.30.40 448
Separator mobile use Stainless steel (material grade 316) Accessories Designation compatible with Description Article No. 230 720 620 Rolls frame Eco-Mobil and Lipu-Mobil Stainless steel, material grade 316 With 4 transport casters Weight: 19 kg 0153.20.81 449
complete disposal Oval shape polyethylene (HD-PE) Separator Eco-Jet-O basic design Product information ACO product advantages Proven stability: 25 years (minimum service life) Upgradeable to extension stage 1 3 Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 Ausbaustufe: Basisausführung B For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Suction and disposal sump with dewatering socket R 1 Odour-tight maintenance opening, diameter: 450 mm Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.1 414 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 450
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 1 DN 0 6 0 320 62 382 3551.34.00 NS 2 DN 0 2 0 440 70 5 3552.34.00 NS 3 DN 0 300 150 630 80 7 3553.34.00 NS 4 DN 0 400 200 830 95 925 3554.34.00 NS 5,5 DN 150 725 360 1430 170 1600 3555.34.00 NS 7 DN 150 800 400 1600 187 1787 3557.34.00 NS 8,5 DN 150 940 475 1900 208 28 3558.34.00 NS DN 150 00 520 2000 220 2220 3560.34.00 ventilation DN 0 min 500 maintenance opening filling device with ball valve and pressure regulator (optional) * sight glass with wiper (optional) * displayed: NS4, operating side right, operating side left would show all components (filling device, sight glass) positioned inlet DN... ØD outlet DN... mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 connection for heating rod (optional) * H 2 H 3 L 1 L 2 B 1 B 2 L1 L2 H1 H2 H3 H4 B1 B2 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 10 1300 830 760 1480 1300 700 770 1 NS 2 10 1300 55 985 1680 1500 700 770 1 NS 3 1450 1650 55 985 1680 1500 700 770 1 NS 4 1760 2000 55 985 1680 1500 700 770 1 NS 5,5 1760 2000 1250 1180 1880 1700 950 20 160 NS 7 1960 2200 1250 1180 1880 1700 950 20 160 NS 8,5 2250 2485 1250 1180 1880 1700 950 20 160 NS 2450 2690 1250 1180 1880 1700 950 20 160 451
complete disposal Oval shape polyethylene (HD-PE) Separator Eco-Jet-OD extension stage 1 Product information ACO product advantages Proven stability: 25 years (minimum service life) Direct emptying without odour build-up Upgradeable to extension stages 2 and 3 Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 Ausbaustufe 1 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1 Odour-tight maintenance opening, diameter: 450 mm Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.1 414 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 452
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 1 DN 0 6 0 320 68 388 3551.64.00 NS 2 DN 0 2 0 440 75 515 3552.64.00 NS 3 DN 0 300 150 630 85 715 3553.64.00 NS 4 DN 0 400 200 830 0 930 3554.64.00 NS 5,5 DN 150 725 360 1430 175 1605 3555.64.00 NS 7 DN 150 800 400 1600 193 1793 3557.64.00 NS 8,5 DN 150 940 475 1900 214 2114 3558.64.00 NS DN 150 00 520 2000 226 2226 3560.64.00 inlet DN... Ø D ventilation DN 0 min 500 maintenance opening disposal connection with Storz-B-coupling R 2 ½, DIN 14308 filling device with solenoid valve and pressure regulator (optional) * sight glass with wiper (optional) * outlet DN... displayed: NS4, operating side right, Operating side left would show all components (filling device, sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 connection for heating rod (optional) * H 2 H 5 H 3 L 1 B 1 B 2 L 2 L1 L2 H1 H2 H3 H4 H5 B1 B2 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 10 1300 830 760 1480 1300 1350 700 770 1 NS 2 10 1300 55 985 1680 1500 1550 700 770 1 NS 3 1450 1650 55 985 1680 1500 1550 700 770 1 NS 4 1760 2000 55 985 1680 1500 1550 700 770 1 NS 5,5 1760 2000 1250 1180 1880 1700 1750 950 20 160 NS 7 1960 2200 1250 1180 1880 1700 1750 950 20 160 NS 8,5 2250 2485 1250 1180 1880 1700 1750 950 20 160 NS 2450 2690 1250 1180 1880 1700 1750 950 20 160 453
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-OS extension stage 2 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Fitting with a disposal pump possible Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Ausbaustufe 2 Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1 Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Odour-tight maintenance opening, diameter: 450 mm Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.1 414 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 454
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 6 0 320 95 415 3571.74.41 3571.74.31 NS 2 DN 0 2 0 440 0 540 3572.74.41 3572.74.31 NS 3 DN 0 300 150 630 120 750 3573.74.41 3573.74.31 NS 4 DN 0 400 200 830 135 965 3574.74.41 3574.74.31 NS 5,5 DN 150 725 360 1430 206 1636 3575.74.41 3575.74.31 NS 7 DN 150 800 400 1600 223 1823 3577.74.41 3577.74.31 NS 8,5 DN 150 940 475 1900 243 2143 3578.74.41 3578.74.31 NS DN 150 00 520 2000 255 2255 3580.74.41 3580.74.31 inlet DN... Ø D ventilation DN 0 min 500 maintenance opening high-pressure spray head filling device with solenoid valve and pressure regulator sight glass with wiper outlet DN... displayed: NS4, operating side right, operating side left would show all components (disposal connection, filling device, sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 high-pressure pump L 4 L 3 L 1 H 2 connection for heating rod (optional) * H 3 H 5 disposal connection with Storz-B-coupling R 2 ½, DIN 14308 L 2 B 1 B 2 Total capacity L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 10 1300 1400 300 830 760 1480 1300 1500 700 770 1 NS 2 10 1300 1400 300 55 985 1680 1500 1700 700 770 1 NS 3 1450 1650 1750 300 55 985 1680 1500 1700 700 770 1 NS 4 1760 2000 2060 300 55 985 1680 1500 1700 700 770 1 NS 5,5 1760 2000 2060 300 1250 1180 1880 1700 1900 950 20 160 NS 7 1960 2200 2260 300 1250 1180 1880 1700 1900 950 20 160 NS 8,5 2250 2485 2550 300 1250 1180 1880 1700 1900 950 20 160 NS 2450 2690 2750 300 1250 1180 1880 1700 1900 950 20 160 455
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-OSE extension stage 2 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Ausbaustufe 2 Suction and disposal sump with dewatering socket R 1 Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening, diameter: 450 mm Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.1 414 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation With disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 456
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 6 0 320 177 497 3571.84.41 3571.84.31 NS 2 DN 0 2 0 440 182 622 3572.84.41 3572.84.31 NS 3 DN 0 300 150 630 194 824 3573.84.41 3573.84.31 NS 4 DN 0 400 200 830 2 40 3574.84.41 3574.84.31 NS 5,5 DN 150 725 360 1430 286 1716 3575.84.41 3575.84.31 NS 7 DN 150 800 400 1600 305 1905 3577.84.41 3577.84.31 NS 8,5 DN 150 940 475 1900 325 2225 3578.84.41 3578.84.31 NS DN 150 00 520 2000 337 2337 3580.84.41 3580.84.31 inlet DN... Ø D ventilation DN 0 min 500 maintenance opening high-pressure spray head filling device with solenoid valve and pressure regulator sight glass with wiper outlet DN... displayed: NS4, operating side right, operating side left would show all components (disposal connection, filling device, sight glass, shut-off valve, switch box) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 high-pressure pump disposal pump switch box Shut-off valve L 4 disposal connection with Storz-B-coupling R 2 ½, DIN 14308 L 3 L 1 L 2 H 2 connection for heating rod (optional) * H 3 B 4 B 1 B 2 H 5 B 3 Total capacity L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 B3 B4 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 10 1300 1800 700 830 760 1480 1300 1500 700 770 500 930 1 NS 2 10 1300 1800 700 55 985 1680 1500 1700 700 770 500 930 1 NS 3 1450 1650 2150 700 55 985 1680 1500 1700 700 770 500 930 1 NS 4 1760 2000 2460 700 55 985 1680 1500 1700 700 770 500 930 1 NS 5,5 1760 2000 2460 700 1250 1180 1880 1700 1900 950 20 625 1180 160 NS 7 1960 2200 2660 700 1250 1180 1880 1700 1900 950 20 625 1180 160 NS 8,5 2250 2485 2950 700 1250 1180 1880 1700 1900 950 20 625 1180 160 NS 2450 2690 3150 700 1250 1180 1880 1700 1900 950 20 625 1180 160 457
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-OA extension stage 3 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Upgrade with disposal pump possible Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Fitting with a disposal pump possible Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Ausbaustufe 3 Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1 Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Odour-tight maintenance opening, diameter: 450 mm Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.1 414 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation No odour build-up 458
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 6 0 320 0 420 3551.74.42 3551.74.32 NS 2 DN 0 2 0 440 5 545 3552.74.42 3552.74.32 NS 3 DN 0 300 150 630 120 750 3553.74.42 3553.74.32 NS 4 DN 0 400 200 830 135 965 3554.74.42 3554.74.32 NS 5,5 DN 150 725 360 1430 2 1640 3555.74.42 3555.74.32 NS 7 DN 150 800 400 1600 226 1826 3557.74.42 3557.74.32 NS 8,5 DN 150 940 475 1900 247 2147 3558.74.42 3558.74.32 NS DN 150 00 520 2000 259 2259 3560.74.42 3560.74.32 inlet DN... Ø D ventilation DN 0 min 500 maintenance opening high-pressure spray head filling device with solenoid valve and pressure regulator sight glass with wiper outlet DN... displayed: NS4, operating side right, operating side left would show all componen (disposal connection, filling device, sight glass, switch box) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 switch box high-pressure pump L 4 L 3 L 1 connection for heating rod (optional) * H 2 H 5 H 3 disposal connection with Storz-B-coupling R 2 ½, DIN 14308 L 2 B 3 B 1 B 2 Total capacity L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 B3 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 10 1300 1400 300 830 760 15 1300 1500 700 770 800 1 NS 2 10 1300 1400 300 55 985 17 1500 1700 700 770 800 1 NS 3 1450 1650 1750 300 55 985 17 1500 1700 700 770 800 1 NS 4 1760 2000 2060 300 55 985 17 1500 1700 700 770 800 1 NS 5,5 1760 2000 2060 300 1250 1180 19 1700 1900 950 20 50 160 NS 7 1960 2200 2260 300 1250 1180 19 1700 1900 950 20 50 160 NS 8,5 2250 2485 2550 300 1250 1180 19 1700 1900 950 20 50 160 NS 2450 2690 2750 300 1250 1180 19 1700 1900 950 20 50 160 459
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-OAE extension stage 3 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Ausbaustufe 3 Suction and disposal sump with dewatering socket R 1 Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening, diameter: 450 mm Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.1 414 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation With disposal pump and remote control available No odour build-up 460
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 6 0 320 177 497 3551.84.42 3551.84.32 NS 2 DN 0 2 0 440 182 622 3552.84.42 3552.84.32 NS 3 DN 0 300 150 630 194 824 3553.84.42 3553.84.32 NS 4 DN 0 400 200 830 2 40 3554.84.42 3554.84.32 NS 5,5 DN 150 725 360 1430 286 1716 3555.84.42 3555.84.32 NS 7 DN 150 800 400 1600 305 1905 3557.84.42 3557.84.32 NS 8,5 DN 150 940 475 1900 325 2225 3558.84.42 3558.84.32 NS DN 150 00 520 2000 337 2337 3560.84.42 3560.84.32 inlet DN... Ø D ventilation DN0 min 500 maintenance opening high-pressure spray head filling device with solenoid valve and pressure regulator sight glass with wiper outlet DN... displayed: NS4, operating side right operating side left would show all components (disposal connection, filling device, sight glass, shut-off valve, switch box) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 high-pressure pump disposal pump switch box shut-off valve L 4 L 3 L 1 H 2 connection for heating rod (optional) * H 5 H 3 disposal connection with Storz-Bcoupling R 2 ½, DIN 14308 L 2 B 4 B 1 B 2 B 3 L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 B3 B4 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 10 1300 1800 700 830 760 1480 1300 1500 700 770 500 930 1 NS 2 10 1300 1800 700 55 985 1680 1500 1700 700 770 500 930 1 NS 3 1450 1650 2150 700 55 985 1680 1500 1700 700 770 500 930 1 NS 4 1760 2000 2460 700 55 985 1680 1500 1700 700 770 500 930 1 NS 5,5 1760 2000 2460 700 1250 1180 1880 1700 1900 950 20 625 1180 160 NS 7 1960 2200 2660 700 1250 1180 1880 1700 1900 950 20 625 1180 160 NS 8,5 2250 2485 2950 700 1250 1180 1880 1700 1900 950 20 625 1180 160 NS 2450 2690 3150 700 1250 1180 1880 1700 1900 950 20 625 1180 160 461
complete disposal Oval shape polyethylene (HD-PE) Separator Eco-Jet-R basic design Product information ACO product advantages Easy to transport and install via single component installation Upgradeable to extension stage 1 3 Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Suction and disposal sump with dewatering socket R 1½ Odour-tight maintenance opening, diameter: 350 mm Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.6 320 Ausbaustufe: Basisausführung B Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 462
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 2 DN 0 290 120 680 119 799 3502.32.30 NS 4 DN 0 500 160 890 134 24 3504.32.30 NS 7 DN 150 830 400 2120 301 2521 3507.32.30 NS DN 150 1150 400 2450 311 2761 35.32.30 NS 15 DN 200 1950 800 36 357 3967 3515.32.30 NS 20 DN 200 2440 800 4070 358 4428 3520.32.30 inlet DN... Ø D min 500 maintenance opening ventilation DN 0 filling device with ball valve and pressure regulator (optional) * sight glass with wiper (optional) * outlet DN... displayed: NS7, operating side right, operating side left would show all components (sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 connection for heating rod (optional) * H 2 H 4 Ø D 1 L 1 L 3 Z L 2 L1 L2 H1 H2 H3 H4 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1255 60 975 905 1320 1520 1 1150 795/2 NS 4 1255 60 1240 1170 1580 1780 1 1150 820/2 NS 7 1820 60 1430 1330 1880 2080 160 1660 785/3 NS 1820 60 1600 1500 2050 2250 160 1660 785/3 NS 15 2130 60 1765 1665 2200 2400 200 1920 880/3 NS 20 2130 60 1955 1855 2400 2600 200 1920 880/3 463
complete disposal Oval shape polyethylene (HD-PE) Separator Eco-Jet-RD extension stage 1 Product information ACO product advantages Easy to transport and install via single component installation Direct emptying without odour build-up Upgradeable to extension stages 2 and 3 Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Odour-tight maintenance opening, diameter: 350 mm Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.6 320 Ausbaustufe 1 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 464
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Empty Full [l] [l] [l] [kg] [kg] NS 2 DN 0 290 120 680 123 803 3502.62.30 NS 4 DN 0 500 160 890 139 29 3504.62.30 NS 7 DN 150 830 400 2120 3 2430 3507.62.30 NS DN 150 1150 400 2450 321 2771 35.62.30 NS 15 DN 200 1950 800 36 358 3968 3515.62.30 NS 20 DN 200 2440 800 4070 360 4430 3520.62.30 inlet DN... min 500 Ø D disposal connection with Storz-Bcoupling R 2 ½, DIN 14308 maintenance opening ventilation DN 0 filling device with ball valve and pressure regulator (optional) * sight glass with wiper (optional) * outlet DN... displayed: NS7, operating side right operating side left would show all componen (disposal connection, sight glass) positioned mirror-inverted to axis *not included in the scope of delivery H 3 H 1 Ø D 1 L 1 connection for heating rod (optional) * L 3 Z H 2 H 4 H 5 L 2 Total capacity L1 L2 L3 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1255 60 170 975 905 1320 1370 1520 1 1150 795/2 NS 4 1255 60 170 1240 1170 1580 1630 1780 1 1150 820/2 NS 7 1820 60 170 1430 1330 1880 1930 2080 160 1660 785/3 NS 1820 60 170 1600 1500 2050 20 2250 160 1660 785/3 NS 15 2130 60 170 1765 1665 2200 2250 2400 200 1920 880/3 NS 20 2130 60 170 1955 1855 2400 2450 2600 200 1920 880/3 465
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-RS extension stage 2 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Fitting with a disposal pump possible Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Odour-tight maintenance opening, diameter: 350 mm Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.6 320 Ausbaustufe 2 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 466
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 290 120 680 156 836 3502.73.41 3502.73.31 NS 4 DN 0 500 160 890 172 62 3504.73.41 3504.73.31 NS 7 DN 150 830 400 2120 344 2464 3507.73.41 3507.73.31 NS DN 150 1150 400 2450 355 2805 35.73.41 35.73.31 NS 15 DN 200 1950 800 36 391 4001 3515.73.41 3515.73.31 NS 20 DN 200 2440 800 4070 392 4462 3520.73.41 3520.73.31 disposal connection with Storz-Bcoupling R 2 ½, DIN 14308 inlet DN... Ø D min 500 high-pressure spray head maintenance opening ventilation DN 0 sight glass with wipe filling device with ball valve and pressure regulator outlet DN... displayed: NS7, operating side right operating side left would show all componen (disposal connection, sight glass, highpressure pump) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 Ø D 1 L 1 connection for heating rod (optional) * L 3 Z H 2 H 4 H 5 L 2 L 4 high-pressure pump L1 L2 L3 L4 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1255 60 170 260 975 905 1320 1370 1520 1 1150 795/2 NS 4 1255 60 170 260 1240 1170 1580 1630 1780 1 1150 820/2 NS 7 1820 60 170 260 1430 1330 1880 1930 2080 160 1660 785/3 NS 1820 60 170 260 1600 1500 2050 20 2250 160 1660 785/3 NS 15 2130 60 170 260 1765 1665 2200 2250 2400 200 1920 880/3 NS 20 2130 60 170 260 1955 1855 2400 2450 2600 200 1920 880/3 467
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-RSE extension stage 2 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening, diameter: 350 mm Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.6 320 Ausbaustufe 2 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation With disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 468
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 290 120 680 189 869 3502.73.81 3502.73.71 NS 4 DN 0 500 160 890 205 95 3504.73.81 3504.73.71 NS 7 DN 150 830 400 2120 377 2497 3507.73.81 3507.73.71 NS DN 150 1150 400 2450 388 2838 35.73.81 35.73.71 NS 15 DN 200 1950 800 36 424 4034 3515.73.81 3515.73.71 NS 20 DN 200 2440 800 4070 437 4507 3520.73.81 3520.73.71 inlet DN... min 500 high-pressure spray head maintenance opening filling device with ball valve and pressure regulator ventilation DN 0 disposal connection with Storz-Bcoupling R 2 ½, DIN 14308 Outlet DN... displayed: NS7, operating side right, operating side left would show all component (disposal connection, switch box, sight glass, high-pressure pump) positioned mirror-inverted to axis. Ø D switch box sight glass with wipe * not included in the scope of delivery H 3 H 1 Z connection for heating rod (optional) * stop valve Ø D 1 L 3 L 4 L 1 disposal pump H 2 H 4 H 5 L 5 L 2 L 6 high-pressure pump Total capacity L1 L2 L3 L4 L5 L6 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1255 60 150 520 65 260 975 905 1320 1370 1520 1 1150 795/2 NS 4 1255 60 150 520 65 260 1240 1170 1580 1630 1780 1 1150 820/2 NS 7 1820 60 150 520 65 260 1430 1330 1880 1930 2080 160 1660 785/3 NS 1820 60 150 520 65 260 1600 1500 2050 20 2250 160 1660 785/3 NS 15 2130 60 150 520 65 260 1765 1665 2200 2250 2400 200 1920 880/3 NS 20 2130 60 150 520 65 260 1955 1855 2400 2450 2600 200 1920 880/3 469
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-RA extension stage 3 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Fitting with a disposal pump possible Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Odour-tight maintenance opening, diameter: 350 mm Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.6 320 Ausbaustufe 3 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation No odour build-up 470
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 290 120 680 165 845 3502.73.42 3502.73.32 NS 4 DN 0 500 160 890 181 71 3504.73.42 3504.73.32 NS 7 DN 150 830 400 2120 353 2473 3507.73.42 3507.73.32 NS DN 150 1150 400 2450 364 2814 35.73.42 35.73.32 NS 15 DN 200 1950 800 36 401 4011 3515.73.42 3515.73.32 NS 20 DN 200 2440 800 4070 401 4471 3520.73.42 3520.73.32 inlet DN... min 500 Ø D high-pressure spray head maintenance opening switch box disposal connection with Storz-Bcoupling R 2 ½, DIN 14308 ventilation DN 0 filling device with solenoid valve and pressure regulator sight glass with wipe outlet DN... displayed: NS7, operating side right operating side left would show all components (disposal connection, switch box, sight glass, high-pressure pump) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 Ø D 1 L 1 connection for heating rod (optional) L 3 Z H 2 H 4 H 5 L 4 L 2 L 5 high-pressure pump Total capacity L1 L2 L3 L4 L5 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1255 60 170 65 260 975 905 1320 1370 1570 1 1150 795/2 NS 4 1255 60 170 65 260 1240 1170 1580 1630 1830 1 1150 820/2 NS 7 1820 60 170 65 260 1430 1330 1880 1930 2130 160 1660 785/3 NS 1820 60 170 65 260 1600 1500 2050 20 2300 160 1660 785/3 NS 15 2130 60 170 65 260 1765 1665 2200 2250 2450 200 1920 880/3 NS 20 2130 60 170 65 260 1955 1855 2400 2450 2650 200 1920 880/3 471
complete disposal Oval shape polyethylene (HD-PE) Separator Hydrojet-RAE extension stage 3 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Ausbaustufe 3 Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening, diameter: 350 mm Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.6 320 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation With disposal pump and remote control available No odour build-up 472
Separator complete disposal Oval shape polyethylene (HD-PE) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 290 120 680 194 874 3502.73.82 3502.73.72 NS 4 DN 0 500 160 890 2 10 3504.73.82 3504.73.72 NS 7 DN 150 830 400 2120 382 2502 3507.73.82 3507.73.72 NS DN 150 1150 400 2450 393 2843 35.73.82 35.73.72 NS 15 DN 200 1950 800 36 442 4052 3515.73.82 3515.73.72 NS 20 DN 200 2440 800 4070 443 4513 3520.73.82 3520.73.72 inlet DN... min 500 Ø D high-pressure spray head maintenance opening switch box filling device with solenoid valve and pressure regulator ventilation DN 0 sight glass with wiper disposal connection with Storz-B-coupling R 2½, DIN 14308 outlet DN... displayed: NS7, operating side right operating side left would show all components (disposal connection, switch box, sight glass, high-pressure pump) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 Z Ø D 1 L1 connection for heating rod (optional) L 3 stop valve disposal pump L 4 H 2 H 4 H 5 L 5 L 2 L 6 high-pressure pump Total capacity L1 L2 L3 L4 L5 L6 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1255 60 150 520 65 260 975 905 1320 1370 1570 1 1150 795/2 NS 4 1255 60 150 520 65 260 1240 1170 1580 1630 1830 1 1150 820/2 NS 7 1820 60 150 520 65 260 1430 1330 1880 1930 2130 160 1660 785/3 NS 1820 60 150 520 65 260 1600 1500 2050 20 2300 160 1660 785/3 NS 15 2130 60 150 520 65 260 1765 1665 2200 2250 2450 200 1920 880/3 NS 20 2130 60 150 520 65 260 1955 1855 2400 2450 2650 200 1920 880/3 473
complete disposal Oval shape polyethylene (HD-PE) Separator Accessories Designation compatible with Description Article No. 525 221 li. Ø455 625 68 Sampling pot DN 0 Eco-Jet/ Hydrojet NS 1 4 Starch separator Fapurat-PE NS 0.5 1 For installation in horizontal pipes DN 0 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg 3300.09.11 525 245 li. Ø455 645 86 Sampling pot DN 150 Eco-Jet/ Hydrojet NS 5.5 Starch separator Fapurat-PE NS 2 For installation in horizontal pipes DN 150 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg 3300.09.21 525 525 70 221 269 li. Ø 455 655 li. Ø455 443 555 6 Sampling pot DN 200 Sampling pot DN 0 Eco-Jet/ Hydrojet NS 15 20 Eco-Jet/ Hydrojet NS 1 4 Starch separator Fapurat-PE NS 0.5 1 For installation in horizontal pipes DN 200 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg For installation in vertical pipes DN 0 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg 3300.09.31 3300..11 525 90 245 li. Ø 455 415 555 Sampling pot DN 150 Eco-Jet/ Hydrojet NS 5.5 Starch separator Fapurat-PE NS 2 For installation in vertical pipes DN 150 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg 3300..21 525 0 265 li. Ø 455 403 555 Sampling pot DN 200 Eco-Jet/ Hydrojet NS 15 20 For installation in vertical pipes DN 200 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg 3300..31 474
Separator complete disposal Oval shape polyethylene (HD-PE) Designation compatible with Description Article No. Inspection window Eco-Jet-O, -OD, -R, -RD width: DN 200 With screen wiper Weight: 5 kg 3300.11. 175 250 ca.400 R 3/4 Ø76 ca.350 Filling unit Eco-Jet-O, -OD, -R, -RD Free outlet in accordance with DIN 1988 part 4 For connection to the drinking water supply With ball valve R ¾ With pressure reducer Weight: 3.5 kg 3300.11.22 525 525 245 221 120 x 5 120 x 5 160 160 li. Ø 455 625 li. Ø 455 645 170 188 Remote control Remote control Coarse trap DN 0 Coarse trap DN 150 Lipurat/ Hydrojet-OA/RA Lipurat/ Hydrojet-OAE/RAE Starch separator Fapurat-OAE Eco-Jet/ Hydrojet NS 1 4 Starch separator Fapurat-PE NS 0.5 1 Eco-Jet/ Hydrojet NS 5.5 Starch separator Fapurat-PE NS 2 For interior fitting or installation in connection box Control conduit without customer-side grounding conductor Up to 50 m: 7 x 1.0 mm² 50 200 m: 7 x 1.5 mm² Protection category IP 54 Weight: 1 kg For interior fitting or installation in connection box Control conduit without customer-side grounding conductor Up to 50 m: 7 x 1.0 mm² 50 m 200 m: 7 x 1.5 mm² Protection category IP 54 Weight: 1 kg For installation in horizontal pipes DN 0 in front of the separator plants Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Stainless steel cage, material grade 316 for retention of coarse materials Odour tight maintenance opening DN 450 Weight: 14 kg For installation in horizontal pipes DN 150 in front of the separator plants Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Stainless steel cage, material grade 316 for retention of coarse materials Odour tight maintenance opening DN 450 Weight: 14 kg 0150.02.86 0150.03.40 3667.00.04 3667.00.05 475
complete disposal Oval shape polyethylene (HD-PE) Separator 525 269 li. Ø 455 655 150 Bohrung Ø40 Designation compatible with Description Article No. Coarse trap DN 200 Eco-Jet/ Hydrojet NS 15 20 For installation in horizontal pipes DN 200 in front of the separator plants Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Stainless steel cage, material grade 316 for retention of coarse materials Odour tight maintenance opening DN 450 Weight: 14 kg 3667.00.06 500 Connection box Starch separator For disposal connection and remote control Stainless steel, material grade 304 Fitting: refinements (width x height x depth) 500 x 500 x 160 mm 7601.80.20 Entsorgungsanschluss Fernbedienung Lüftungsanschluss 30 505 565 Entsorgungsanschluss Bohrung Ø40 370 300 Flush-mounted frame Connection box Connection box 7601.80.20 Eco-FPI with direct suction Eco-Jet OD/RD/GD Lipurex OD/RD Hydrojet OS/OSE/RS/RSE Lipurat OS/OSE/RS/RSE (width x height x depth) 565 x 565 x 15 mm For disposal connection DN 80 Stainless steel, material grade 304 Design refinements Door stop Right or left Door is lockable (width x height x depth) 370 x 330 x 250 mm Weight: 8 kg 7601.80.21 7601.80.22 371 25 331 381 Flush-mounted frame Connection box 7601.80.22 Stainless steel, material grade 304 (width x height x depth) 421 x 381 x 25 mm 7601.80.23 421 476
Separator complete disposal Oval shape polyethylene (HD-PE) ØR Designation compatible with Description Article No. Stop valve for freestanding installation Starch separator for free-standing installation Cast iron Valve plate, stainless steel spindle, material grade 304 H1 H2 DN 0 Length (L): 50 mm Shaft travel (H1 H2): 365 465 mm Diameter hand wheel: 200 mm DN 150 Length (L): 60 mm Shaft travel (H1 H2): 478 639 mm Diameter hand wheel: 200 mm 7602.00.12 7604.00.12 L Flange connection Stop valve 7602.00.12 7604.00.12 76.00.12 DN 200 Length (L): 60 mm Shaft travel (H1 H2): 542 743 mm Diameter hand wheel: 250 mm Stainless steel, material grade 304 Sealing: NBR 76.00.12 Ø 1 DN 0 Length (L): 75 mm 7602.00.13 L DN 150 Length (L): 75 mm 7604.00.13 15 Ø120 Ø1 140 Ø133 80 Inlet valve DN 0 Waste water lifting plants Polyethylene grease separator Polyethylene starch separator DN 200 Length (L): 120 mm PVC Construction length: 176 mm Weight: 2.75 kg 76.00.13 0175.13.84 176 12 15 Inlet valve DN 150 Waste water lifting plants Polyethylene grease separator Polyethylene starch separator PVC Construction length: 226 mm Weight: 6.5 kg 0175.13.85 Ø174 Ø160 Ø186 8 226 160 475 R 1 1/2 Heating rod For homogenization of the grease layer Inc. control Electrical connection 400 V/50 Hz/16 A/6.0 kw 7300.01.00 477
complete disposal Oval shape stainless steel (material grade 316) Separator Lipurex-O basic design Product information ACO product advantages Proven stability: 25 years (minimum service life) Upgradeable to extension stage 1 3 Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Suction and disposal sump with dewatering socket R 1½ Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 5.5 Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.1 413 Ausbaustufe: Basisausführung B Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 478
Separator complete disposal Oval shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 1 DN 0 0 0 320 130 450 7551.34.00 NS 2 DN 0 200 0 440 135 575 7552.34.00 NS 3 DN 0 300 150 630 155 785 7553.34.00 NS 4 DN 0 400 200 830 175 05 7554.34.00 NS 5,5 DN 150 550 360 1430 230 1660 7555.34.00 NS 7 DN 150 700 400 1600 255 1855 7557.34.00 NS 8,5 DN 150 850 475 1900 295 2195 7558.34.00 NS DN 150 00 520 2000 315 2315 7560.34.00 filling device with solenoid valve and pressure regulator (optional) * H 1 inlet DN... Ø D min 500 maintenance opening L 3 L 1 ventilation DN 0 sight glass with wiper (optional) * connection for heating rod (optional) * outlet DN... H 2 H 3 H 4 displayed: NS4, operating side right o perating side left would show all components (sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery L 2 B 1 B 2 L1 L2 L3 H1 H2 H3 H4 B1 B2 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 905 10 115 830 760 1200 1550 635 760 1 NS 2 905 10 115 55 985 1320 1700 635 760 1 NS 3 1255 1450 115 55 985 1320 1700 635 760 1 NS 4 1605 1800 115 55 985 1320 1700 635 760 1 NS 5,5 1655 1920 115 1255 1185 1570 1950 885 160 NS 7 1855 2120 115 1255 1185 1570 1950 885 160 NS 8,5 2155 2420 115 1255 1185 1570 1950 885 160 NS 2345 26 115 1255 1185 1570 1950 885 160 479
complete disposal Oval shape stainless steel (material grade 316) Separator Lipurex-OD extension stage 1 Product information ACO product advantages Proven stability: 25 years (minimum service life) Direct emptying without odour build-up Upgradeable to extension stages 2 and 3 Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 5.5 Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.1 413 Ausbaustufe 1 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 480
Separator complete disposal Oval shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Empty Full [l] [l] [l] [kg] [kg] NS 1 DN 0 0 0 320 135 455 7551.64.00 NS 2 DN 0 200 0 440 140 580 7552.64.00 NS 3 DN 0 300 150 630 160 790 7553.64.00 NS 4 DN 0 400 200 830 180 7554.64.00 NS 5,5 DN 150 550 360 1430 245 1675 7555.64.00 NS 7 DN 150 700 400 1600 260 1860 7557.64.00 NS 8,5 DN 150 850 475 1900 300 2200 7558.64.00 NS DN 150 00 520 2000 320 2320 7560.64.00 filling device with solenoid valve and pressure regulator (optional) * min 500 disposal connection with Storz-coupling R2 ½, DIN 14308 maintenance opening ventilation DN0 displayed: NS4, operating side right operating side left would show all components (disposal connection, sight glass) positioned mirror-inverted to axis. H 4 H 1 inlet DN... Ø D L 3 L 1 sight glass with wiper (optional) * connection for heating rod (optional) * outlet DN... H 2 H 3 H 5 * not included in the scope of delivery L 2 B 1 B 2 Total capacity L1 L2 L3 H1 H2 H3 H4 H5 B1 B2 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 905 10 115 830 760 1200 1380 1550 635 760 1 NS 2 905 10 115 55 985 1320 1500 1700 635 760 1 NS 3 1255 1450 115 55 985 1320 1500 1700 635 760 1 NS 4 1605 1800 115 55 985 1320 1500 1700 635 760 1 NS 5,5 1655 1920 115 1255 1185 1570 1750 1950 885 160 NS 7 1855 2120 115 1255 1185 1570 1750 1950 885 160 NS 8,5 2155 2420 115 1255 1185 1570 1750 1950 885 160 NS 2345 26 115 1255 1185 1570 1750 1950 885 160 481
complete disposal Oval shape stainless steel (material grade 316) Separator Lipurat-OS extension stage 2 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Fitting with a disposal pump possible Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1 Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 5.5 Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.1 413 Ausbaustufe 2 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 482
Separator complete disposal Oval shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 0 0 320 165 485 7571.74.41 7571.74.31 NS 2 DN 0 200 0 440 170 6 7572.74.41 7572.74.31 NS 3 DN 0 300 150 630 190 820 7573.74.41 7573.74.31 NS 4 DN 0 400 200 830 2 40 7574.74.41 7574.74.31 NS 5,5 DN 150 550 360 1430 280 17 7575.74.41 7575.74.31 NS 7 DN 150 700 400 1600 290 1890 7577.74.41 7577.74.31 NS 8,5 DN 150 850 475 1900 330 2230 7578.74.41 7578.74.31 NS DN 150 00 520 2000 350 2350 7580.74.41 7580.74.31 disposal connection with Storz-Bcoupling R 2 ½,DIN 14308 Inlet DN... maintenance opening high-pressure spray head ventilation DN 0 min 500 filling device with solenoid valve and pressure regulator outlet DN... displayed: NS4, operating side right operating side left would show all compone (disposal connection, sight glass) positione mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 Ø D L 4 L 1 L 3 sight glass with wiper connection for heating rod (optional) * highpressure pump H 2 H 3 H 5 L 2 B 1 B 2 L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 905 10 1320 115 830 760 1200 1380 1550 635 760 1 NS 2 905 10 1320 115 55 985 1320 1500 1700 635 760 1 NS 3 1255 1450 1670 115 55 985 1320 1500 1700 635 760 1 NS 4 1605 1800 2020 115 55 985 1320 1500 1700 635 760 1 NS 5,5 1655 1920 2070 115 1255 1185 1570 1750 1950 885 160 NS 7 1855 2120 2270 115 1255 1185 1570 1750 1950 885 160 NS 8,5 2155 2420 2570 115 1255 1185 1570 1750 1950 885 160 NS 2345 26 2760 115 1255 1185 1570 1750 1950 885 160 483
complete disposal Oval shape stainless steel (material grade 316) Separator Lipurat-OSE extension stage 2 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Ausbaustufe 2 Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 5.5 Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.1 413 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation With disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 484
Separator complete disposal Oval shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 0 0 320 215 535 7571.84.41 7571.84.31 NS 2 DN 0 200 0 440 220 660 7572.84.41 7572.84.31 NS 3 DN 0 300 150 630 240 870 7573.84.41 7573.84.31 NS 4 DN 0 400 200 830 260 90 7574.84.41 7574.84.31 NS 5,5 DN 150 550 360 1430 335 1765 7575.84.41 7575.84.31 NS 7 DN 150 700 400 1600 345 1915 7577.84.41 7577.84.31 NS 8,5 DN 150 850 475 1900 385 2285 7578.84.41 7578.84.31 NS DN 150 00 520 2000 400 2400 7580.84.41 7580.84.31 disposal connection with Storz-B-coupling R 2 ½, DIN 14308 Inlet DN... maintenance opening high-pressure spray head ventilation DN 0 min 500 filling device with solenoid valve and pressure regulator outlet DN... displayed: NS4, operating side right operating side left would show all components (disposal connection, filling device, sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 stop valve disposal pump L 4 L 1 L 3 L 2 B 4 B 1 B 2 B 3 Ø D switch box sight glass with wiper connection for heating rod (optional) * highpressure pump H 2 H 3 H 5 L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 B3 B4 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 905 10 1850 650 830 760 1200 1380 1550 635 760 370 800 1 NS 2 905 10 1850 650 55 985 1320 1500 1700 635 760 370 800 1 NS 3 1255 1450 2200 650 55 985 1320 1500 1700 635 760 370 800 1 NS 4 1605 1800 2550 650 55 985 1320 1500 1700 635 760 370 800 1 NS 5,5 1655 1920 2600 650 1255 1185 1570 1750 1950 885 450 00 160 NS 7 1855 2120 2800 650 1255 1185 1570 1750 1950 885 450 00 160 NS 8,5 2155 2420 30 650 1255 1185 1570 1750 1950 885 450 00 160 NS 2345 26 3300 650 1255 1185 1570 1750 1950 885 450 00 160 485
complete disposal Oval shape stainless steel (material grade 316) Separator Lipurat-OA extension stage 3 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Fitting with a disposal pump possible Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Ausbaustufe 3 Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 5.5 Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.1 413 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation No odour build-up 486
Separator complete disposal Oval shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 0 0 320 165 485 7571.74.42 7571.74.32 NS 2 DN 0 200 0 440 170 6 7572.74.42 7572.74.32 NS 3 DN 0 300 150 630 195 825 7573.74.42 7573.74.32 NS 4 DN 0 400 200 830 215 45 7574.74.42 7574.74.32 NS 5,5 DN 150 550 360 1430 285 1715 7575.74.42 7575.74.32 NS 7 DN 150 700 400 1600 295 1895 7577.74.42 7577.74.32 NS 8,5 DN 150 850 475 1900 335 2235 7578.74.42 7578.74.32 NS DN 150 00 520 2000 350 2350 7580.74.42 7580.74.32 disposal connection with Storz-B-coupling R 2 ½, DIN 14308 inlet DN... maintenance opening high-pressure spray head ventilation DN 0 min 500 filling device with solenoid valve and pressure regulator outlet DN... displayed: NS4, operating side right, operating side left would show all components (disposal connection, filling device, sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 Ø1 switch box L 4 L 1 L 3 sight glass with wiper connection for heating rod (optional) * highpressure pump H 2 H 3 H 5 L 2 B 3 B 4 B 1 B 2 L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 B3 B4 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 905 10 1320 115 830 760 1200 1380 1550 635 760 370 800 1 NS 2 905 10 1320 115 55 985 1320 1500 1700 635 760 370 800 1 NS 3 1255 1450 1670 115 55 985 1320 1500 1700 635 760 370 800 1 NS 4 1605 1800 2020 115 55 985 1320 1500 1700 635 760 370 800 1 NS 5,5 1655 1920 2070 115 1255 1185 1570 1750 1950 885 550 00 160 NS 7 1855 2120 2270 115 1255 1185 1570 1750 1950 885 550 00 160 NS 8,5 2155 2420 2570 115 1255 1185 1570 1750 1950 885 550 00 160 NS 2345 26 2760 115 1255 1185 1570 1750 1950 885 550 00 160 487
complete disposal Oval shape stainless steel (material grade 316) Separator Lipurat-OAE extension stage 3 Product information ACO product advantages Proven stability: 25 years (minimum service life) Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Minimization of disposal and maintenance costs via economical gradation of the nominal Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Ausbaustufe 3 Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 5.5 Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.1 413 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation With disposal pump and remote control available No odour build-up 488
Separator complete disposal Oval shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity [l] [l] [l] [kg] [kg] Empty Full Right Left NS 1 DN 0 0 0 320 215 535 7571.84.42 7571.84.32 NS 2 DN 0 200 0 440 220 660 7572.84.42 7572.84.32 NS 3 DN 0 300 150 630 240 870 7573.84.42 7573.84.32 NS 4 DN 0 400 200 830 260 90 7574.84.42 7574.84.32 NS 5,5 DN 150 550 360 1430 335 1765 7575.84.42 7575.84.32 NS 7 DN 150 700 400 1600 345 1915 7577.84.42 7577.84.32 NS 8,5 DN 150 850 475 1900 385 2285 7578.84.42 7578.84.32 NS DN 150 00 520 2000 400 2400 7580.84.42 7580.84.32 disposal connection with Storz-B- coupling R 2 ½, DIN 14308 inlet DN... maintenance opening high-pressure spray head ventilation DN 0 min 500 filling device with solenoid valve and pressure regulator outlet DN... displayed: NS4, operating side right operating side left would show all components (disposal connection, filling device, sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 4 H 1 stop valve disposal pump Ø D switch box L 4 L 1 L 3 sight glass with wiper connection for heating rod (optional) * highpressure pump H 2 H 5 L 2 B 4 B 1 B 2 B 3 H 3 L1 L2 L3 L4 H1 H2 H3 H4 H5 B1 B2 B3 B4 D [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 1 905 10 1850 650 830 760 1200 1380 1550 635 760 370 800 1 NS 2 905 10 1850 650 55 985 1320 1500 1700 635 760 370 800 1 NS 3 1255 1450 2200 650 55 985 1320 1500 1700 635 760 370 800 1 NS 4 1605 1800 2550 650 55 985 1320 1500 1700 635 760 370 800 1 NS 5,5 1655 1920 2600 650 1255 1185 1570 1750 1950 885 450 00 160 NS 7 1855 2120 2800 650 1255 1185 1570 1750 1950 885 450 00 160 NS 8,5 2155 2420 30 650 1255 1185 1570 1750 1950 885 450 00 160 NS 2345 26 3300 650 1255 1185 1570 1750 1950 885 450 00 160 489
complete disposal Curved shape stainless steel (material grade 316) Separator Lipurex-R basic design Product information ACO product advantages Easy to transport and install via single component installation Upgradeable to extension stage 1 3 Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Suction and disposal sump with dewatering socket R 1½ Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 7 20 Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.6 320 Ausbaustufe: Basisausführung B Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 490
Separator complete disposal Curved shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 2 DN 0 2 120 715 168 882 7502.32.00 NS 4 DN 0 420 165 915 178 93 7504.32.00 NS 7 DN 150 705 400 1950 332 2284 7507.32.00 NS DN 150 00 400 2250 342 2589 75.32.00 NS 15 DN 200 1630 800 3350 485 3835 7515.32.00 NS 20 DN 200 21 800 3820 501 4321 7520.32.00 inlet DN... min 500 Ø D maintenance opening ventilation DN 0 filling device with ball valve and pressure regulator (optional) * sight glass with wiper (optional) * outlet DN... displayed: NS 7, operating side rights, operating side left would show all components (sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 connection for heating rod (optional) H 2 H 4 Ø D 1 L 1 L 3 Z L 2 L1 L2 L3 H1 H2 H3 H4 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1180 120 150 975 905 1200 1520 1 00 785/2 NS 4 1180 120 150 1240 1170 1450 1770 1 00 785/2 NS 7 1800 120 150 1430 1330 1780 20 160 1500 790/3 NS 1800 120 150 1600 1500 1950 2270 160 1500 790/3 NS 15 2050 120 150 1755 1685 2120 2440 2 1750 820/3 NS 20 2050 120 150 1935 1885 2320 2640 2 1750 820/3 491
complete disposal Curved shape stainless steel (material grade 316) Separator Lipurex-RD extension stage 1 Product information ACO product advantages Easy to transport and install via single component installation Direct emptying without odour build-up Upgradeable to extension stages 2 and 3 Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 7 20 Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.6 320 Ausbaustufe 1 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 492
Separator complete disposal Curved shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage Empty Full [l] [l] [l] [kg] [kg] NS 2 DN 0 2 120 715 172 886 7502.62.00 NS 4 DN 0 420 165 915 186 11 7504.62.00 NS 7 DN 150 705 400 1950 338 2290 7507.62.00 NS DN 150 00 400 2250 351 2598 75.62.00 NS 15 DN 200 1630 800 3350 492 3842 7515.62.00 NS 20 DN 200 21 800 3820 5 4330 7520.62.00 inlet DN... min 500 Ø D disposal connection with Storz-B-coupling R 2 ½ DIN 14308 filling device with ball valve and pressure regulator (optional) * maintenance opening ventilation DN 0 sight glass with wiper (optional) * outlet DN... displayed: NS7, operating side right operating side left would show all componen (disposal connection, sight glass) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 Ø D 1 L 1 connection for heating rod (optional) L 3 Z H 2 L 2 H 4 H 5 Total capacity L1 L2 L3 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1180 120 150 975 905 1200 1400 1520 1 00 785/2 NS 4 1180 120 150 1240 1170 1450 1650 1770 1 00 785/2 NS 7 1800 120 150 1430 1330 1780 1930 20 160 1500 790/3 NS 1800 120 150 1600 1500 1950 20 2270 160 1500 790/3 NS 15 2050 120 150 1755 1685 2120 2250 2440 2 1750 820/3 NS 20 2050 120 150 1935 1885 2320 2450 2640 2 1750 820/3 493
complete disposal Curved shape stainless steel (material grade 316) Separator Lipurat-RS extension stage 2 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Fitting with a disposal pump possible Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For installation in rooms With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Ausbaustufe 2 Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 7 20 Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.6 320 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 494
Separator complete disposal Curved shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 2 120 715 204 918 7502.73.41 7502.73.31 NS 4 DN 0 420 165 915 218 1133 7504.73.41 7504.73.31 NS 7 DN 150 705 400 1950 367 2319 7507.73.41 7507.73.31 NS DN 150 00 400 2250 382 2629 75.73.41 75.73.31 NS 15 DN 200 1630 800 3350 523 3873 7515.73.41 7515.73.31 NS 20 DN 200 21 800 3820 541 4361 7520.73.41 7520.73.31 disposal connection with Storz-B-coupling R 2½ DIN 14308 high-pressure spray head filling device with ball valve and pressure regulator inlet DN... min 500 maintenance opening ventilation DN 0 outlet DN... displayed: NS7, operating side right operating side left would show all componen (disposal connection, sight glass, high pressure pump) positioned mirror-inverted to axis. Ø D sight glass with wiper * not included in the scope of delivery H 3 H 1 Ø D 1 L 1 connection for heating rod (optional)* L 3 Z H 2 H 4 H 5 L 2 L 4 high-pressure pump Total capacity L1 L2 L3 L4 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1180 120 150 250 975 905 1200 1400 1520 1 00 785/2 NS 4 1180 120 150 250 1240 1170 1450 1650 1770 1 00 785/2 NS 7 1800 120 150 250 1430 1330 1780 1930 20 160 1500 790/3 NS 1800 120 150 250 1600 1500 1950 20 2270 160 1500 790/3 NS 15 2050 120 150 250 1755 1685 2120 2250 2440 2 1750 820/3 NS 20 2050 120 150 250 1955 1885 2320 2450 2640 2 1750 820/3 495
complete disposal Curved shape stainless steel (material grade 316) Separator Lipurat-RSE extension stage 2 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Hydro mechanical high-pressure cleaning - requires only a cold water connection Upgradeable to extension stage 3 Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Ausbaustufe 2 Manual operation of the high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 7 20 Filling unit with ball valve (connection R ¾ ) for manual re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.6 320 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation With disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation Optionally disposal pump and remote control available No odour build-up 496
Separator complete disposal Curved shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 2 120 715 236 950 7502.73.61 7502.73.51 NS 4 DN 0 420 165 915 249 1164 7504.73.61 7504.73.51 NS 7 DN 150 705 400 1950 399 2351 7507.73.61 7507.73.51 NS DN 150 00 400 2250 414 2661 75.73.61 75.73.51 NS 15 DN 200 1630 800 3350 558 3908 7515.73.61 7515.73.51 NS 20 DN 200 21 800 3820 576 4396 7520.73.61 7520.73.51 inlet DN... min 500 high-pressure spray head maintenance opening switch box filling device with ball valve and pressure regulator ventilation DN 0 outlet DN... disposal connection with Storz-B-coupling R 2½ DIN 14308 displayed: NS7, operating side right operating side left would show all components (disposal connection, sight glass, switch box, high pressure pump) positioned mirror-inverted to axis. * not included in the scope of delivery Ø D sight glass with wiper H 3 H 1 connection for heating rod (optional) * stop valve H 2 H 4 H 5 Z Ø D 1 L 3 L 4 L 1 disposal pump L 5 L 2 L 6 high pressure pump Total capacity L1 L2 L3 L4 L5 L6 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1180 120 135 520 1 250 975 905 1200 1400 1520 1 00 785/2 NS 4 1180 120 135 520 1 250 1240 1170 1450 1650 1770 1 00 785/2 NS 7 1800 120 135 520 1 250 1430 1330 1780 1930 20 160 1500 790/3 NS 1800 120 135 520 1 250 1600 1500 1950 20 2270 160 1500 790/3 NS 15 2050 120 135 520 1 250 1755 1685 2120 2250 2440 2 1750 820/3 NS 20 2050 120 135 520 1 250 1955 1885 2320 2450 2640 2 1750 820/3 497
complete disposal Curved shape stainless steel (material grade 316) Separator Lipurat-RA extension stage 3 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Fitting with a disposal pump possible Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Ausbaustufe 3 Suction and disposal sump with dewatering socket R 1½ Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 7 20 Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/3.9 kw System ACO Passavant Official approval Z 54.6 320 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation No odour build-up 498
Separator complete disposal Curved shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 2 120 715 207 921 7502.73.42 7502.73.32 NS 4 DN 0 420 165 915 221 1136 7504.73.42 7504.73.32 NS 7 DN 150 705 400 1950 370 2322 7507.73.42 7507.73.32 NS DN 150 00 400 2250 385 2632 75.73.42 75.73.32 NS 15 DN 200 1630 800 3350 526 3876 7515.73.42 7515.73.32 NS 20 DN 200 21 800 3820 543 4364 7520.73.42 7520.73.32 inlet DN... min 500 Ø D disposal connection with Storz-B-coupling R 2½, DIN 14308 high-pressure spray head maintenance opening switch box filling device with solenoid valve and pressure regulator ventilation DN 0 sight glass with wiper outlet DN... displayed: NS7, operating side right operating side left would show all components (disposal connection, switch box, sight glass, high-pressure pump) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 Ø D 1 L 1 connection for heating rod (optional)* L 3 Z H 2 H 4 H 5 L 4 L 2 L 5 high-pressure pump Total capacity L1 L2 L3 L4 L5 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1180 120 150 1 250 975 905 1200 1400 1570 1 00 785/2 NS 4 1180 120 150 1 250 1240 1170 1450 1650 1820 1 00 785/2 NS 7 1800 120 150 1 250 1430 1330 1780 1930 2150 160 1500 790/3 NS 1800 120 150 1 250 1600 1500 1950 20 2320 160 1500 790/3 NS 15 2050 120 150 1 250 1755 1685 2120 2250 2490 2 1750 820/3 NS 20 2050 120 150 1 250 1955 1885 2320 2450 2690 2 1750 820/3 499
complete disposal Curved shape stainless steel (material grade 316) Separator Lipurat-RAE extension stage 3 Product information ACO product advantages Easy to transport and install via single component installation Disposal, cleaning and filling without odour build-up Pre- and post- cleaning times can be set individually Hydro mechanical high-pressure cleaning - requires only a cold water connection Small installation clearance Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With integrated sludge trap Operator side: right/left Disposal connection, Storz B coupling R 2½ Suction and disposal sump with dewatering socket R 1½ Ausbaustufe 3 Inspection window with wiper Automatic high-pressure interior cleaning with pump pressure: 175 bar Capacity: 13 l/min Milling, mixing, flushing in one step Standard control with centralised fault signal Disposal pump with free flow impeller Motor rating: 3.0 kw/2850 U/min Delivery performance: 20 m³/h with 1 bar medium delivery head Stop valve in front of disposal pump Odour-tight maintenance opening Diameter: 300 mm at NS 1 4 Diameter: 500 mm at NS 7 20 Filling unit with solenoid valve (connection R ¾ ) for automatic re-filling Inlet and drainage connections in accordance with EN 877 Electrical connection: 400 V/50 Hz/16 A/6.9 kw System ACO Passavant Official approval Z 54.6 320 Features of basic design: Disposal and cleaning via covers Odour build-up during disposal and cleaning Features of extension stage 1: Odour build-up during cleaning Features of extension stage 2: High-pressure cleaning with manual operation Optionally disposal pump available No odour build-up Features of extension stage 3: Fully automatic operation With disposal pump and remote control available No odour build-up 500
Separator complete disposal Curved shape stainless steel (material grade 316) Ordering information width Sludge trap Capacity Weight Article No. Grease storage [l] [l] [l] [kg] [kg] Empty Full Right Left NS 2 DN 0 2 120 715 236 950 7502.73.62 7502.73.52 NS 4 DN 0 420 165 915 249 1164 7504.73.62 7504.73.52 NS 7 DN 150 705 400 1950 399 2351 7507.73.62 7507.73.52 NS DN 150 00 400 2250 415 2661 75.73.62 75.73.52 NS 15 DN 200 1630 800 3350 558 3908 7515.73.62 7515.73.52 NS 20 DN 200 21 800 3820 576 4396 7520.73.62 7520.73.52 inlet DN... Ø D min 500 high-pressure spray head maintenance opening switch box filling device with solenoid valve and pressure regulator ventilation DN 0 sight glass with wiper disposal connection with Storz-B-coupling R 2½, DIN 14308 outlet DN... displayed: NS7, operating side right operating side left would show all componen (disposal connection, switch box, sight glass high-pressure pump) positioned mirror-inverted to axis. * not included in the scope of delivery H 3 H 1 Z connection for heating rod (optional) * Ø D 1 L 3 L 4 L 1 stop valve disposal pump H 2 H 4 H 5 L 5 L 2 L 6 high-pressure pump Total capacity L1 L2 L3 L4 L5 L6 H1 H2 H3 H4 H5 D D1 Z/n [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 1180 120 135 520 1 250 975 905 1200 1400 1570 1 00 785/2 NS 4 1180 120 135 520 1 250 1240 1170 1450 1650 1820 1 00 785/2 NS 7 1800 120 135 520 1 250 1430 1330 1780 1930 2150 160 1500 790/3 NS 1800 120 135 520 1 250 1600 1500 1950 20 2320 160 1500 790/3 NS 15 2050 120 135 520 1 250 1755 1685 2120 2250 2490 2 1750 820/3 NS 20 2050 120 135 520 1 250 1955 1885 2320 2450 2690 2 1750 820/3 501
complete disposal Curved shape stainless steel (material grade 316) Separator Accessories Designation compatible with Description Article No. 295 127 395 152 395 177 355 127 455 455 60 152 60 177 60 Ø323 480 Ø323 480 Ø323 480 Ø323 320 405 Ø323 320 405 Ø323 320 405 57 82 7 Sampling pipe DN 0 Sampling pipe DN 150 Sampling pipe DN 200 Sampling pipe DN 0 Sampling pipe DN 150 Sampling pipe DN 200 Lipurex/Lipurat/Lipator/Lipatomat NS 1 4 Starch separator Fapurat NS 0.5 1 Light-oil separator Coalisator- R/-RD NS 3 Lipurex/Lipurat/Lipator/Lipatomat NS 5.5 Starch separator Fapurat NS 2 Light-oil separator Coalisator- R/-RD NS 6 Lipurex/Lipurat/Lipator/Lipatomat NS 15 20 Light-oil separator Coalisator-E NS 20 Lipurex/Lipurat/Lipator/Lipatomat NS 1 4 Starch separator Fapurat NS 0.5 1 Light-oil separator Coalisator- R/-RD NS 3 Lipurex/Lipurat/Lipator/Lipatomat NS 5.5 Starch separator Fapurat NS 2 Light-oil separator Coalisator- R/-RD NS 6 Lipurex/Lipurat/Lipator/Lipatomat NS 15 20 Light-oil separator Coalisator-E NS 20 Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 0 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 13 kg Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 150 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 14 kg Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 200 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 15 kg Stainless steel, material grade 316 Curved design For installation in vertical pipes DN 0 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 13 kg Stainless steel, material grade 316 Curved design For installation in vertical pipes DN 150 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 14 kg Stainless steel, material grade 316 Curved design For installation in vertical pipes DN 200 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 15 kg 7300.09. 7300.09.20 7300.09.30 7300..20 7300.15.20 7300.16.20 502
Separator complete disposal Curved shape stainless steel (material grade 316) 295 127 395 152 395 ca.325 177 Ø323 480 Ø323 480 Ø323 480 215 290 Ø76 120 x 5 120 x 5 ca.350 160 160 57 82 7 R 3/4 Designation compatible with Description Article No. Coarse trap DN 0 Coarse trap DN 150 Coarse trap DN 200 Inspection window Filling unit Remote control Remote control Lipurex/Lipurat/Lipator/Lipatomat NS 1 4 Starch separator Fapurat NS 0.5 1 Lipurex/Lipurat/Lipator/Lipatomat NS 5.5 Starch separator Fapurat NS 2 LipurexLipurat/Lipator/Lipatomat NS 15 20 Lipurex-O, -OD, -R, -RD Lipurex-O, -OD, -R, -RD Lipurat/ Hydrojet-OA/RA Lipurat/ Hydrojet-OAE/RAE Starch separator Fapurat-OAE Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 0 in front of the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 15 kg Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 150 in front of the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 16 kg Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 200 in front of the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 17 kg width: DN 200 With screen wiper Weight: 5 kg Free outlet in accordance with DIN 1988 part 4 For connection to the drinking water supply With ball valve R ¾ Weight: 2 kg For interior fitting or installation in connection box Control conduit without customer-side grounding conductor Up to 50 m: 7 x 1.0 mm² 50 200 m: 7 x 1.5 mm² Protection category IP 54 Weight: 1 kg For interior fitting or installation in connection box Control conduit without customer-side grounding conductor Up to 50 m: 7 x 1.0 mm² 50 m 200 m: 7 x 1.5 mm² Protection category IP 54 Weight: 1 kg 7300.09.70 7300.09.80 7300.09.90 7602.00.26 7602.00.25 0150.02.86 0150.03.40 503
complete disposal Curved shape stainless steel (material grade 316) Separator Bohrung Ø40 Designation compatible with Description Article No. 500 Connection box Starch separator For disposal connection and remote control Stainless steel, material grade 304 Fitting: refinements (width x height x depth) 500 x 500 x 160 mm 7601.80.20 Entsorgungsanschluss Fernbedienung Lüftungsanschluss 30 505 Flush-mounted frame Connection box 7601.80.20 (width x height x depth) 565 x 565 x 15 mm 7601.80.21 565 Entsorgungsanschluss Bohrung Ø40 370 371 25 421 ØR 331 381 300 Connection box Flush-mounted frame Stop valve Eco-FPI with direct suction Eco-Jet OD/RD/GD Lipurex OD/RD Hydrojet OS/OSE/RS/RSE Lipurat OS/OSE/RS/RSE Connection box 7601.80.22 for freestanding installation Starch separator for free-standing installation For disposal connection DN 80 Stainless steel, material grade 304 Design refinements Door stop Right or left Door is lockable (width x height x depth) 370 x 330 x 250 mm Weight: 8 kg Stainless steel, material grade 304 (width x height x depth) 421 x 381 x 25 mm Cast iron Valve plate, stainless steel spindle, material grade 304 7601.80.22 7601.80.23 H1 H2 DN 0 Length (L): 50 mm Shaft travel (H1 H2): 365 465 mm Diameter hand wheel: 200 mm DN 150 Length (L): 60 mm Shaft travel (H1 H2): 478 639 mm Diameter hand wheel: 200 mm 7602.00.12 7604.00.12 L DN 200 Length (L): 60 mm Shaft travel (H1 H2): 542 743 mm Diameter hand wheel: 250 mm 76.00.12 504
Separator complete disposal Divided shape polyethylene (HD-PE) Designation compatible with Description Article No. Flange connection Stop valve 7602.00.12 7604.00.12 76.00.12 Stainless steel, material grade 304 Sealing: NBR Ø 1 DN 0 Length (L): 75 mm 7602.00.13 L DN 150 Length (L): 75 mm 7604.00.13 DN 200 Length (L): 120 mm 76.00.13 160 475 R 1 1/2 Heating rod For homogenization of the grease layer Inc. control Electrical connection 400 V/50 Hz/16 A/6.0 kw 7300.01.00 505
complete disposal Divided shape polyethylene (HD-PE) Separator Eco-Jet-G basic design Product information ACO product advantages Proven stability: 25 years (minimum service life) Can be installed in locations difficult to access, via division of the plant into three parts Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With separate sludge trap Odour-tight maintenance opening, diameter: 450 mm Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.6 363 Ordering information Capacity Weight Article No. Sludge trap Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 2 2 80 480 75 555 3802.00.00 NS 4 420 160 880 115 995 3804.00.00 inlet DN 0 maintenance opening outlet DN 0 05 935 1360 Ø 1 min 500 a b L 1 L 2 700 L1 L2 A B [mm] [mm] [mm] [mm] NS 2 1180 1360 5 660 NS 4 2070 2250 945 1115 506
Separator complete disposal Divided shape polyethylene (HD-PE) Eco-Jet-GD extension stage 1 Product information ACO product advantages Proven stability: 25 years (minimum service life) Can be installed in locations difficult to access, via division of the plant into three parts Direct emptying without odour build-up Marginal weight plant in accordance with EN 1825 and DIN 4040 0 For free-standing installation in rooms - frost free With separate sludge trap With disposal connection DN 50 and Storz B coupling R 2 Suction and disposal sump with dewatering socket R 1 Odour-tight maintenance opening, diameter: 450 mm Inlet and drainage connections in accordance with EN 877 System ACO Passavant Official approval Z 54.6 363 Ordering information Capacity Weight Article No. Sludge trap Grease storage Total capacity Empty Full [l] [l] [l] [kg] [kg] NS 2 2 80 480 75 555 3802.50.00 NS 4 420 160 880 115 995 3804.50.00 inlet DN 0 Ø 1 min 500 disposal connection with Storz-B-coupling R 2 DIN 14308 maintenance opening outlet DN 0 05 935 1360 a b L 1 L 2 700 L1 L2 A B [mm] [mm] [mm] [mm] NS 2 1180 1360 5 660 NS 4 2070 2250 945 1115 507
complete disposal Divided shape polyethylene (HD-PE) Separator Accessories 525 525 525 221 221 70 221 li. Ø455 625 li. Ø455 443 555 li. Ø 455 625 68 188 Schmutzfängeminderer Druck- Kugelhahn Ø1 350 Rohrverbinder 140 620 Designation compatible with Description Article No. Sampling pot DN 0 Sampling pot DN 0 Coarse trap DN 0 Filling unit Eco-Jet/ Hydrojet NS 1 4 Starch separator Fapurat-PE NS 0.5 1 Eco-Jet/ Hydrojet NS 1 4 Starch separator Fapurat-PE NS 0.5 1 Eco-Jet/ Hydrojet NS 1 4 Starch separator Fapurat-PE NS 0.5 1 Eco-Jet G/GD For installation in horizontal pipes DN 0 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg For installation in vertical pipes DN 0 after the separator plant Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Odour tight maintenance opening DN 450 Weight: 7 kg For installation in horizontal pipes DN 0 in front of the separator plants Curved shape, with Socket seal (material SBR) on the inlet and pipe spigot on the drain Stainless steel cage, material grade 316 for retention of coarse materials Odour tight maintenance opening DN 450 Weight: 14 kg For installation in front of the separator Stainless steel, material grade 316 Consisting of Pipe sockets DN 0 Length: 300 mm Filling unit with welded odour seal and R ¾ ball valve With pressure reducer 1 pipe connector DN 0 3300.09.11 3300..11 3667.00.04 0153.06.76 15 Inlet valve DN 0 Waste water lifting plants Polyethylene grease separator Polyethylene starch separator PVC Construction length: 176 mm Weight: 2.75 kg 0175.13.84 Ø120 Ø1 Ø133 80 176 508
Separator complete disposal Divided shape polyethylene (HD-PE) Entsorgungsanschluss Bohrung Ø40 370 371 300 Designation compatible with Description Article No. Connection box Eco-FPI with direct suction Eco-Jet OD/RD/GD Lipurex OD/RD Hydrojet OS/OSE/RS/RSE Lipurat OS/OSE/RS/RSE For disposal connection DN 80 Stainless steel, material grade 304 Design refinements Door stop Right or left Door is lockable (width x height x depth) 370 x 330 x 250 mm Weight: 8 kg 7601.80.22 25 331 381 Flush-mounted frame Connection box 7601.80.22 Stainless steel, material grade 304 (width x height x depth) 421 x 381 x 25 mm 7601.80.23 421 Sed tat. Ulput volenis nit atie facipisi. 509
partial disposal Stainless steel (material grade 304) Separator Lipator manual operation Product information ACO product advantages Disposal without interruption in operation Optimally suited for installation in rooms with no direct access for disposal vehicles Ideal for use in conjunction with wet waste disposal plants Fresh grease separator plant in accordance with EN 1825 and DIN 4040 0 For installation in frost-protected rooms With integrated sludge trap Stainless steel cabinet and lower section, material grade 304 Heating element and additional thermal insulation for fat homogenization 230 V/1.5 kw Inlet and drainage connections in accordance with EN 877 With ball valve DN 50 for fat and sludge draw-off Collector tank for grease and sediment sludge Capacity: 60 l Cover and hose connection 2 replacement containers with cover Capacity: 60 l Agitating device with 1 phase AC motor in lower housing section 230 V/90 W Manual membrane pump for pressure boost for grease removal Electrical connection 230 V 50/60 Hz 1.6 kw System ACO Passavant Official approval Z 54.6 163 (for NS 2 15) Official approval Z 54.1 452 (for NS 20) Ordering information width Total capacity Weight Empty Full Diameter x Height Largest individual component Heaviest individual component [l] [kg] [kg] [mm] [kg] Article No. NS 2 DN 0 220 130 350 680 x 50 85 7672.30.00 NS 4 DN 0 880 376 1256 1380 x 800 70 7674.30.00 NS 7 DN 150 880 379 1259 1380 x 800 70 7677.30.00 NS DN 150 2080 591 2671 1830 x 600 95 7680.30.00 NS 15 DN 200 2080 591 2671 1830 x 600 95 7685.30.00 NS 20 DN 200 2080 640 2725 1830 x 600 115 7690.30.00 5
Separator partial disposal Stainless steel (material grade 304) min 500 connection ventilation, cleaning cap agitating device drive inlet DN... outlet DN... grease collecting space heating rod insulating covers grease draw-off sludge draw-off E D C F manual membrane pump inlet DN... stop valve ventilation bridge bottom outlet A switch box sludge collecting space outlet DN... ca. G grease collecting container B note: arrangement of the collecting containe can be turned around the center of the sludge collecting container L L1 L2 L3 H H1 H2 [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 10 680 260 700 1750 1305 1235 NS 4 2150 1380 550 900 2050 1600 1450 NS 7 2150 1380 550 900 2050 1600 1530 NS 2800 1850 750 00 2350 1900 1750 NS 15 2800 1850 750 00 2350 1900 1830 NS 20 3000 1850 750 00 2350 1900 1830 511
partial disposal Stainless steel (material grade 304) Separator Lipatomat automatic control Product information ACO product advantages Automatic controlled grease and sludge draw-off without interruption in operation Optimally suited for installation in rooms with no direct access for disposal vehicles Ideal for use in conjunction with wet waste disposal plants Fresh grease separator plant in accordance with EN 1825 and DIN 4040 For installation in frost-protected rooms With integrated sludge trap Stainless steel cabinet and lower section, material 1.4031 Heating element and additional thermal insulation for fat homogenization 230 V/1.5 kw Inlet and drainage connections in accordance with EN 877 With electrical ball valve DN 50 for fat and sludge draw-off Ordering information width Total capacity Collector tank for grease and sediment sludge Capacity: 60 l Cover and hose connection 2 replacement containers with cover Capacity: 60 l Agitating device with 1 phase AC motor in lower housing section 230 V/90 W Grease layer thickness measurement Control of agitating device Vat fill-level measurement Program control with centralised fault signal for ZLT Filling unit with solenoid valve for supporting sludge and grease draw-off Electrical connection 230 V 50/60 Hz 1.6 kw System ACO Passavant Official approval Z 54.6 163 (for NS 2 15) Official approval Z 54.1 452 (for NS 20) Weight Empty Full Diameter x Height Largest individual component Heaviest individual component [l] [kg] [kg] [mm] [kg] Article No. NS 2 DN 0 220 130 350 680 x 50 85 7672.60.00 NS 4 DN 0 880 361 1241 1380 x 800 70 7674.60.00 NS 7 DN 150 880 363 1243 1380 x 800 70 7677.60.00 NS DN 150 2080 605 2685 1830 x 600 95 7680.60.00 NS 15 DN 200 2080 605 2685 1830 x 600 95 7685.60.00 NS 20 DN 200 2080 640 2725 1830 x 600 115 7690.60.00 512
Separator partial disposal Stainless steel (material grade 304) min 500 filling device with solenoid valve and pressure regulator agitating device drive inlet DN... outlet DN... grease collecting space grease sensor heating rod insulating covers automatic grease draw-off automatic sludge draw-off D E F stop valve switch box bottom outlet sludge collecting space inlet DN... A connection ventilation, cleaning cap C ventilation bridge outlet DN... ca. G B note: arrangement of the collecting containers can be turned around the center of the facility grease collecting container sludge collecting container L L1 L2 L3 H H1 H2 [mm] [mm] [mm] [mm] [mm] [mm] [mm] NS 2 10 680 260 700 1750 1305 1235 NS 4 2150 1380 550 900 2050 1600 1450 NS 7 2150 1380 550 900 2050 1600 1530 NS 2800 1850 750 00 2350 1900 1750 NS 15 2800 1850 750 00 2350 1900 1830 NS 20 2800 1850 750 00 2350 1900 1830 513
partial disposal Stainless steel (material grade 304) Separator Accessories Designation compatible with Description Article No. 295 127 395 152 395 177 355 127 455 455 60 152 60 177 60 Ø323 480 Ø323 480 Ø323 480 Ø323 320 405 Ø323 320 405 Ø323 320 405 57 82 7 Sampling pipe DN 0 Sampling pipe DN 150 Sampling pipe DN 200 Sampling pipe DN 0 Sampling pipe DN 150 Sampling pipe DN 200 Lipurex/Lipurat/Lipator/Lipatomat NS 1 4 Starch separator Fapurat NS 0.5 1 Light-oil separator Coalisator- R/-RD NS 3 Lipurex/Lipurat/Lipator/Lipatomat NS 5.5 Starch separator Fapurat NS 2 Light-oil separator Coalisator- R/-RD NS 6 Lipurex/Lipurat/Lipator/Lipatomat NS 15 20 Light-oil separator Coalisator-E NS 20 Lipurex/Lipurat/Lipator/Lipatomat NS 1 4 Starch separator Fapurat NS 0.5 1 Light-oil separator Coalisator- R/-RD NS 3 Lipurex/Lipurat/Lipator/Lipatomat NS 5.5 Starch separator Fapurat NS 2 Light-oil separator Coalisator- R/-RD NS 6 Lipurex/Lipurat/Lipator/Lipatomat NS 15 20 Light-oil separator Coalisator-E NS 20 Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 0 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 13 kg Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 150 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 14 kg Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 200 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 15 kg Stainless steel, material grade 316 Curved design For installation in vertical pipes DN 0 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 13 kg Stainless steel, material grade 316 Curved design For installation in vertical pipes DN 150 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 14 kg Stainless steel, material grade 316 Curved design For installation in vertical pipes DN 200 behind the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 15 kg 7300.09. 7300.09.20 7300.09.30 7300..20 7300.15.20 7300.16.20 514
Separator partial disposal Stainless steel (material grade 304) Designation compatible with Description Article No. 295 127 Ø323 480 57 Coarse trap DN 0 Lipurex/Lipurat/Lipator/Lipatomat NS 1 4 Starch separator Fapurat NS 0.5 1 Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 0 in front of the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 15 kg 7300.09.70 395 152 Ø323 480 82 Coarse trap DN 150 Lipurex/Lipurat/Lipator/Lipatomat NS 5.5 Starch separator Fapurat NS 2 Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 150 in front of the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 16 kg 7300.09.80 395 177 Ø323 480 580 7 Coarse trap DN 200 Spare vat LipurexLipurat/Lipator/Lipatomat NS 15 20 Lipator/Lipatomat Stainless steel, material grade 316 Curved design Gradient: 70 mm For installation in horizontal pipes DN 200 in front of the separator With pipe connector and tempo clutch Connections in accordance with EN 877 Weight: 17 kg Vat Volume: 60 l With cover and tension ring Height: c. 630 mm Diameter: c. 380 mm Weight: 5 kg 7300.09.90 7600.00.15 Ø380 515
system solution Suspension equipment Separator Upstream container mono Product information ACO product advantages Low turbulence waste water feed to the grease separator plant (displacement pump) Low energy consumption Safe pump pneumatic level switching Increased operational safety via air bubble injection Application Low inlet connection in front of the grease separator plant For installation in rooms Polyethylene collector tank Material HD-PE Useable volume: 260 l Compact delivery unit/features Collector tank with inlet socket Suction connecting flange Ventilation connection port DN 0 Fresh-water connection socket R 1½ Maintenance opening with plug cap Locked odour-tight Diameter: 350 mm Filter insert located after inlet Mounting material, measuring tube long/short to the pneumatic level switching With 1 eccentric spiral pump (2 l/s) Ordering information Pressure pipe with special mounting piece Backflow valve Mini compressor for air bubble injection with fitting material Control line for pneumatic level switching Control box/features Electrical connection: 400 V/50 Hz Protection category IP 54 : 380 x 300 x 2 mm (width x height x depth) Plug in, 1.5 m cable with CEE 5 pole plug Coated steel (RAL 7032) wall-mounted cabinet Time-lag fuse according to on-site conditions Operation via key/bosh light toggle switch element Display via direction of turn control, high alarm and 2 malfunction illuminated pushbuttons with cut off and reset function Pneumatic level switching via membrane pressure switch Thermal motor fuse monitoring of pumps Error signals, visual and acoustic Dry contact centralised fault signal and pump operating signal Type width P1 Current consumption 1 m Weight Article No. Empty Full [kw] [A] [l/s] [kg] [kg] 2 DN 0 1,5 16 2 275 675 0175.26.63 4 DN 150 3 16 4 335 735 0175.26.65 7 DN 150 5,5 16 7 345 745 0175.26.67 DN 150 5,5 16 370 770 0175.26.69 516
Separator system solution Suspension equipment 380 x 2 300 switch box plug-ready control cables of the pneumatic level switch inlet DN * PE-sleeve screw cap SG 385 with threaded ring LW 350 alarm mini compressor ventilation connection DN 0 Ø8-114 special fastening piece for the elastic connection of the pressure pipe H 2 H 1 H Z filter insert OFF NLZ ON pump1 backflow valve flange bend H S H D anchor buoyancy-proof with supplied screws and dowels fresh water connection R 1 1/2 D 1 L long measuring tube with bubble injection (OFF, P1, alarm) inlet DN * PE-sleeve ventilation DN0 / SML (expelled through the roof) eccentric screw pump B Type L B1 Individual component diameter H1 H2 H3 H4 H5 [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 2 1180 1540 850 900 60 730 770 160 4 1180 1730 850 900 60 730 800 190 7 1230 1870 850 900 60 730 855 215 1230 1870 850 900 60 730 855 215 517
system solution Suspension equipment Separator Upstream container duo Product information ACO product advantages Low turbulence waste water feed to the grease separator plant (displacement pump) Low energy consumption Safe pump pneumatic level switching Increased operational safety via air bubble injection Application Low inlet connection in front of the grease separator plant For installation in rooms Polyethylene collector tank Material HD-PE Useable volume: 200 l Compact delivery unit/features: Collector tank with inlet socket Suction connecting flange Ventilation connection port DN 0 Fresh-water connection socket R 1½ Maintenance opening with plug cap Locked odour-tight Diameter: 350 mm Filter insert located after inlet Mounting material, measuring tube long/short to the pneumatic level switching With 2 eccentric spiral pumps Ordering information Type width Consolidated pressure pipe with special mounting piece Mini compressor for air bubble injection with fitting material Control line for pneumatic level switching Control box/features Electrical connection: 400 V/50 Hz Protection category IP 54 : 380 x 600 x 2 mm (width x height x depth) Plug in, 1.5 m cable with CEE 5 pole plug Coated steel (RAL 7032) wall-mounted cabinet Time-lag fuse according to on-site conditions Operation via 2 key/screen light toggle switch elements Display via direction of turn control, high alarm and 2 malfunction illuminated pushbuttons with cut off and reset function Pneumatic level switching via membrane pressure switch Thermal motor fuse monitoring of pumps Error signals, visual and acoustic Dry contact centralised fault signal and pump operating signal P1 Current consumption 1 m Weight Article No. Empty Full [kw] [A] [l/s] [kg] [kg] 2 DN 0 1,5 16 2 360 760 0175.25.95 4 DN 150 3 16 4 480 880 0175.25.97 7 DN 150 5,5 32 7 500 900 0175.25.99 DN 150 5,5 32 550 950 0175.26.01 518