Heated Portion Pack Display Case Instruction Manual Model #5580BV1, Model #5588 and Model #5581 Part No. 74797 Revised April 2000 Cincinnati, OH 45241-4807 USA e-mail: goldme19@eos.net www.gmpopcorn.com
SAFETY PRECAUTIONS This equipment is designed and sold for commercial use only. This equipment is not to be used by the consumer in home use. Do not allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all installation instructions before operating the equipment. Always wear safety glasses when servicing this equipment. NEVER put your fingers or any object into the heating area. We do NOT assume any liability for injury due to careless handling or operation of this equipment. Any alterations to this equipment will void the warranty and may cause a dangerous situation. NEVER make alterations to the equipment. Machine must be properly grounded to prevent electrical shock to personnel. Do NOT immerse the equipment in water. Always unplug the equipment before cleaning or servicing. NOTE The information, specifications and illustrations contained in this manual represent the latest data available at time of publication. Right is reserved to make changes as required at the discretion of Gold Medal Products Company without notice.
Heated Portion Pack Display Case INSTALLATION Your new WARMER is shipped completely assembled, ready to operate. After removing the corrugated carton from the machine, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transpiration company. Remove all cardboard packing and tape from the machine. Wipe all exposed surfaces with a damp cloth to remove fingerprints, smears etc. which may have occurred during unpacking and handling. NOTE: This model is for portion pack cheese and prepackaged potentially non-hazardous food only. ELECTRICAL REQUIREMENTS Standard voltage for the warmer is 120 Volt, 60 cycle, single phase A.C. current. The switch to turn the unit ON / OFF is located under the door. CARE AND CLEANING The aluminum frame of the warmer is easy to keep clean. Usually a damp cloth will remove all dirt and grease spots. NEVER USE ABRASIVES on the aluminum framework. The glass should always be clean and sparkling. Remember the inside of the glass must be cleaned too. Empty out all product and remove shelves periodically, and clean inside of the machine. A damp cloth will usually pick up any debris. BULB REPLACEMENT Remove screws over lighted sign out through the top. Pull the lamp from the socket. GLASS REPLACEMENT We do not ship glass, obtain from local glass shop or hardware store. Always purchase double strength type glass. Size is FRONT & SIDE: Model 5581 16 29 /32" x 16 1 /2" x 1 /8" Model 5580BV1 16 29 /32" x 16 1 /2" x 1 /8" Model 5588 16 11 /16" x 30" x 1 /8" 1 MANUAL NO. 74797
Heated Portion Pack Display Case MAINTENANCE INSTRUCTIONS THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN- TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR. Adequate eye protection must be used when servicing this equipment to prevent the possibility of injury. Do NOT immerse the equipment in water. Unplug your machine before servicing. ORDERING SPARE PARTS 1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list. 2. When ordering, please include part number, part name, and quantity needed. 3. Please include your model name and machine serial number (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 or, place orders at: (513) 769-7676 Fax: (513) 769-8500 E-mail: goldme19@eos.net or Web Page www.gmpopcorn.com See our complete catalog for more Gold Medal Funfood Equipment and Supplies 2 MANUAL NO. 74797
Heated Portion Pack Display Case DISPLAY CASE EXPLODED VIEW 3 MANUAL NO. 74797
PARTS LIST DISPLAY CASE Model Model Model #5580BV1 #5581 #5588 Heated Portion Pack Display Case Item # Part No. Part No. Part No. Description 1 74781 74781 74905 Cabinet Assembly 2 74777 74777 74777 Top Cover 3 87996 87996 87996 Thermostat 4 74667/40838 74667/40838 74667/40838 Thermostat Mount Brackets 5 40838 40838 40838 Sensor Bracket 6 74735 74735 74735 Motor Plate 7 74736 74736 74736 Blower Box 8 74720 74720 74720 Heat Element 120V - 475 Watt 9 74737 74737 74737 Blower Motor 10 74748 74748 74748 Hi-Limit Thermostat 11 74775 74775 74775 Air Guide 12 74788 74788 74788 Light Tube Cover 13 74786 74786 74786 Sign Frame Angle 14 74796 74179 74179 Sign 15 74181 74182 74182 Sign Cover 16 41021 41021 41021 Light Tube Holder / Starter 17 41020 41020 41020 Light Tube Holder 18 41022 41022 41022 Ballast 19 41023 41023 41023 Starter 20 41057 41057 41057 Light Tube 21 74787 74787 74787 Light Deflector 22 41350 41350 41350 Male Hinge, Right 23 41349 41349 41349 Male Hinge Left 24 74168 74168 74168 Female Hinge, Right 25 74169 74169 74169 Female Hinge, Left 26 74779 74779 77501 Glass Panel 27 74164 74164 74164 Glass Extrusion 28 74166 74166 74961 Door 74961R Right hand Door 29 47120 47120 47120 Knob 30 75267 75267 75267 Tee Bolt 31 47693 47693 47698 Rigid Channel 32 47693 47693 47693 Rigid Channel 33 76368 76368 74915 Front Corner Post 34 76369 76369 74916 Left Rear Corner Post 35 76370 76370 74913 Right Rear Corner Post 36 74167 74167 74671 Corner Post, Filler 37 74798 74798 74766L Shelf Support, Left Hand 38 74799 74799 74766R Shelf Support, Right Hand 39 74772 74772 74772 Rack 40 74163 74163 74624 Drip Pan Assembly 41 47561 47561 47561 Door Magnet 43 74778 74778 74778 Bottom Cover 44 22038 22038 22038 Lead-In Cord, 15 Amp 45 87163 87163 87163 Strain Relief 46 40324 40324 40324 Switch 47 49123 49123 49123 Crutch Tip 48 47328 47328 47328 Glide N/S 74673 Door Support 4
Heated Portion Pack Display Case ELECTRICAL SCHEMATIC 5 MANUAL NO. 74797
WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said GOLD MEDAL equipment or any part thereof. The term Original Purchaser as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS COMPANY, or their authorized distributor, for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. GOLD MEDAL PRODUCTS COMPANY 10700 Medallion Drive Cincinnati, OH 45241-4807 USA