SKE Spiraline Fine Screen - SCC 1. Screenings are captured by the C shaped screening basket and elevated up by the shaftless spiral. This spiral is also fitted with screen cleaning brushes, which ensure the screening surface remains clean. 2. Once captured, the screenings are elevated to a convenient disposal height by the screen. 3. The spiral runs on heavy duty longitudinal wear bars which enable the screenings to de-water during elevation. 4. The screen operates by differential water levels upstream and downstream, or by timer. 5. Three Point Screenings Washing System in screening, conveying and compaction sections. 6. This unit is a four in one Screen, Washer, Conveyor and Compactor. Screens 1. Screen basket, shaftless screw conveying section, legs, wear bars and outlet constructed in AISI 304 or AISI 316 stainless steel. 2. De-watering / conveying spiral in high tensile carbon steel, AISI 304 or AISI 316 stainless steel. 3. Transmission: direct coupled worm gear NORD gear reducer. 1. Bearing structure: no lower bearing so no bearings are in contact with the screenings or liquor. 2. Screen baskets: 0.25 0.5 1mm 2mm wedge-wire, 3mm 10mm perforated plate. 3. Low running speed giving low wear characteristics. 4. Electric motor: 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. Optional Extras 1. Lengthening & shortening of conveying section to meet your specific disposal heights. 2. Continuous bagging system for screenings. Model Length Height Throughput @ 5mm Screen Channel kw Perf (Clean Water) Width Depth Spiraline SCC 200 5355 2990 39 L/s 350 800 0.55 Spiraline SCC 300 5355 3000 44 L/s 350 800 0.55 Spiraline SCC 400 5355 3000 75L/s 450 800 0.55 Spiraline SCC 500 5355 3000 110 L/s 550 800 0.55 Spiraline SCC 600 5760 3230 165 L/s 650 800 1.1 Spiraline SCC 700 6100 3430 269 L/s 850 1000 1.1
SKE Spiraline Fine Screen - SCT 1. Screenings pumped to the flanged inlet of the self-supporting tank are captured by the C shaped screening basket and elevated off the face of the screen by the shaftless spiral. This spiral is also fitted with screen cleaning brushes, thus ensuring the screening surface remains clean. 2. Once captured, the screenings are elevated to a convenient disposal height by the screen. 3. The spiral runs on heavy duty longitudinal wear bars which enable the screenings to de-water during elevation. 4. The screen operates by differential water levels upstream and downstream, or by timer. 5. Three point screenings washing system in the screening, conveying sections and compaction. 6. This unit is a four in one screen, washer conveyor and compactor. Screens 1. Screen basket, shaftless screw conveying section, legs, wear bars and outlet constructed in AISI 304 or AISI 316 stainless steel. 2. De-watering / conveying spiral in high tensile carbon steel, AISI 304 or AISI 316 stainless steel. 3. Transmission direct coupled worm gear reducer. 1. Bearing structure no lower bearing so no bearings are in contact with the screenings or liquor. 2. Screen baskets: 0.25 0.5 1mm 2mm wedge-wire 3mm 10mm perforated plate. 3. Low running speed giving low wear characteristics. 4. Electric Motor: 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. Optional Extras 1. Lengthening & shortening of conveying section to meet your specific disposal heights. 2. Continuous bagging system for screenings. Model Height Length Height of tank Length of tank Width of tank Throughput @ 5mm Perf (Clean Water) Inlet/Outlet SCT 200 2130 3690 990 1300 350 39 l/s DN150 PN10 0.55 SCT 300 2200 3790 990 1300 406 44 l/s DN200 PN10 0.55 SCT 400 2200 3790 1200 1605 516 75 l/s DN250 PN10 0.55 SCT 500 2200 3790 1290 1675 616 110 l/s DN300 PN10 0.55 SCT 600 2450 4200 1320 1755 716 165 l/s DN400 PN10 1.1 SCT 700 2950 5070 1630 2080 916 269 l/s DN500 PN10 1.1 kw
SKE Klearline Vertical Fine Brushed Screen BPS 1. The screen positioned in a reinforced concrete channel separates the medium and fine solid particles from the effluent. 2. These particles are then removed from the screen by brushes mounted on a self-lubricating chain, which continuously remove the waste off the screen. 3. A scraper keeps the moving brushes clean and removes the waste. Screens 1. Manufactured entirely in AISI 304 stainless steel, with driving chain and rollers which are selflubricating in water, brushes with double shock-absorption, and rocking scraper. 2. Geared motor with adjustable torque limiting device. 3. Screens: perforated plate from 0.8mm to 5mm; slots from 1x20mm to 5x20mm. 1. Load-bearing frame in AISI 304 stainless steel. 2. Cleaning drive chain with polyester links and rollers, self lubricating in water. 3. Cleaning brushes in nylon, complete with shockabsorbing supports. 4. Scraper for automatic brush cleaning, equipped with small, double acting oil-dynamic ram. 5. Gearbox: - worm screw reducer and helical gears, with pre-torque and torque limiting device. 6. Electric motor: 400 Volt, 50 Hz, three-phase 1400 rpm, IP 55, insulation class F. 1. Manufactured in AISI 316 stainless steel. 2. Lateral sealing bands can be fitted to suit channel requirements. Flow rates dependant on channel size. Type Channel Width Discharge ht from Invert Level Brush Speed m/min BPS40 400 2500 6 0.37 BPS60 600 2500 6 0.37 BPS80 800 2500 6 0.37 BPS100 1000 2500 6 0.37 BPS130 1300 2500 6 0.75 BPS150 1500 2500 6 0.75 BPS200 2000 2500 6 0.75 kw
SKE Klearline Rotary Drum Screen RDS 1. The effluent to be treated is pumped to a delivery tank designed to ensure that the fluid is distributed evenly over the entire surface of the screen. 2. The solids contained in the effluent come into contact with the slowly rotating screening cylinder, where they are removed by a skimming blade. 3. The filtered water passes inside the drum and out again through the bottom filter element, this action cleaning the filtering surface of the screen. 4. In addition, the system includes a further internal filter drum washing stage using spray nozzles. 5. The filter element is cleansed of any particles with each revolution, ready for the next filtering cycle. Screens 1. The load-bearing structure of the screen is made entirely from AISI 304 stainless steel, with filtration cylinder and ramp equipped with spraying nozzles, skimming blade in anti-wear material, complete with collection tank and frame for floor anchorage. 2. Geared motor with adjustable torque limiting device. 3. Screen spacing available from 0.25 0.5 1 1.25 1.5 2 and 2.5mm wedge-wire 1. Feed tank and collection tank made of AISI 304 stainless steel. 2. Screening drum made of AISI 304 stainless steel wedge-wire. It is mounted on the loadbearing tank on life-long lubricated bearings. 3. Scraper blade for cleaning the cylinder in brass, with stainless steel support. The blade is provided with small hydraulic resisting rams. 4. Spraying nozzles for counter-washing the inside of the filtration cylinder. 5. Gearbox: - worm screw reducer and helical gears with pre-torque and torque limiting device. 6. Electric Motor: 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. 1. Manufactured in AISI 316 stainless steel. Flow rates dependant on size of Screen. Model Width Length Throughput Inlet PN10 Outlet PN10 kw RDS20 600 400 8-32m 3 /h 50 150 0.18 RDS40 1300 400 36-160m 3 /h 100 150 0.37 RDS70 1300 700 63-263m 3 /h 200 250 0.37 RDS100 1300 1000 89-370m 3 /h 200 250 0.37 RDS130 1300 1300 115-480m 3 /h 250 300 0.75 RDS190 1300 1900 176-700m 3 /h 300 400 0.75 RDS300/90 1550 3000 320-1720m 3 /h 350x2 400x2 1.50
SKE Klearline Vertical Fine Bar Screen FVS 1. Separates solids from incoming effluent in the reinforced concrete channel. 2. The water passes through the bar grid while all the solids are held back to be collected and elevated by cleaning combs to the top of the screen. The shape of the bars allows discharge of the solids and thorough cleaning of the combs. 1. Bearing structure of cold-rolled plate, filtering grid made of rolled bar, all AISI 304 stainless steel. 2. Cleaning combs made of wear-resistant plastic mounted on a special support of AISI 304 stainless steel. 3. Transmission chain in AISI 304 stainless steel, with rollers made of polyester which are selflubricating in water. 4. Scraper complete with brush for cleaning the combs. 5. Geared motor with built-in adjustable torque limiting device. Screens 1. Bearing structure made of stainless steel with sliding guides for the chains. 2. Drive chain with stainless steel links and rollers made of polyester which are self-lubricating in water. 3. Cleaning Combs mounted on stainless steel supports. 4. Scraper for automatic cleaning of the comb, with shock-absorbing elements. 5. Gearbox: - Reduction gear with worm screw and helical gears, with built-in torque limiting device. 6. Electric Motor: 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. 1. Manufactured in AISI 316 stainless steel. 2. Lateral sealing bands can be fitted to suit channel requirements. Flow rates dependant on channel size. Model Channel Width Discharge Ht From Channel Invert Comb Speed (m/min) Bar Spacing FVS50 500 2500 2.5 3 5 10 0.18 FVS60 600 2500 2.5 3 5 10 0.18 FVS75 750 2500 2.5 3 5 10 0.18 FVS100 1000 2500 2.5 3 5 10 0.37 FVS130 1300 2500 2.5 3 5 10 0.37 kw
SKE Klearline Static Rundown Screens Models C and CV 1. The effluent to be treated flows into the feeding tank, then overflows from the weir and is evenly distributed across the whole filtering surface, uniquely composed of small grids. 2. The particular shape of these grids, with corrugated bars, allows efficient separation of the solids from the liquor, continuously and without blockages. 3. It is possible to adjust the inclination of the filtering panel to allow for greater solid separation. 4. The separated solids collect at the front of the screen while filtrate flows to the back. Screens 1. Made entirely of AISI 304 stainless steel. 2. Adjustable filtering panel composed of special grids with high mechanical strength (resistance from +160 C to -35 C). 3. Grid spacing available: 0.5-0.75-1.0-1.5-2.0-3.0 mm. 1. Feed tank in AISI 304 stainless steel. 2. Filtering panel: - two panels with frame in AISI 304 stainless steel with interchangeable filtering grids, composed of material with high mechanical strength (polyfluoride vinylidene, +160 C to -35 C). 1. Complete unit manufactured in AISI 316 stainless steel. 2. AISI 304 stainless wedge wire screening surface. 3. Overflow built into the feed tank in the frame structure. 4. An electric vibrator is available on the CV Model to aid separation of particularly dirty screenings. Model Height Width Depth Qm 3 Filtering Area /h m 2 C40 1000 650 900 2-6 0.4 C60 1000 890 900 4-8 0.6 C108 1300 1155 1030 8-19 1.08 C160 1800 1155 1600 17-50 1.6 CV608 1000 945 900 4-6 0.6 CV1080 1300 1210 1030 8-19 1.08 CV1600 1880 1210 1600 17-50 1.6
SKE Spiraline Shaftless Screw Compactor SCP 1. The solid material with high water content enters the hopper and drops to the lower screen allowing the removal of free water. 2. Solids are then elevated by the shaftless spiral to the compaction zone. 3. The compaction chamber is composed of a de-watering barrel with slotted holes to allow the filtrate to escape and drain out. 4. Conveyed solids form a plug in the compaction chamber and the conveying action of the spiral compacts the plug thereby allowing de-watering. 5. At this point, the squeeze-dried material passes through a conveying tube into a container/skip. 6. The separated water drains by large hose back to be discharged for further treatment. Compactors 1. Shaftless screw conveying section, legs, wear bars, inlets and outlet constructed in AISI 304 stainless steel or AISI 316 stainless steel. 2. De-watering / conveying spiral in high tensile carbon steel or AISI 304 / AISI 316 stainless steel. 3. Transmission: Direct coupled worm gear reducer. 4. Spiral liner: UHMDW or AISI 304 / AISI 316 stainless steel de-watering bars. 1. Bearings - No hanger/intermediate or end bearings. 2. Low running speed giving low wear characteristics. 3. Drainage below inlet and at compaction barrel with interconnecting hose. 4. Electric Motor 400 Volt, 50 Hz, threephase, 1400 rpm, IP 55, insulation class F. 5. Inclined at 5-25º. 1. Lengthening of conveying section, supports, horizontal and inclined inlet hoppers. Model Length Length of conveying Section Compaction Chamber Length Width kw Q m3/h SCP 200 2900 2000 500 330 1.5 2 SCP 300 4120 3000 720 430 3.0 5 SCP 400 5400 4000 940 550 5.5 8
SKE Klearline Hydraulic Compactor HCP 1. The solids material with high water content enters the hopper and drops to the compression chamber. 2. The compression chamber is composed of brass runners for the pistons to slide on and holes in the base of the chamber for drainage. 3. A hydraulic ram with a backward and forward action thrusts the material towards a cone-shaped outlet at the end of the compression chamber to enable the solids to be separated from the water. 4. At this point, the squeeze-dried material (with up to 75% dry solids possible) passes through a conveying tube into a container. 5. The separated water is collected in a tank situated under the compactor and returned to the channel for further treatment. 6. The speed and power of the hydraulic ram can be adjusted according to the type and quantity of material to be treated. Compactors 1. Made entirely of AISI 304 stainless steel; it is composed of a compression chamber with a hydraulic ram, controlled by a special hydraulic unit complete with valves and pressure gauge, a feeding hopper and a tank for collecting the liquid. 1. Compression Chamber made of AISI 304 stainless steel, complete with brass sliding guides for the ram. 2. Hydraulic Control Unit with a 50 litre tank made of AISI 304 stainless steel, complete with a 90 micron suction filter; gear pump; valves for automatic thrust inversion; pressure gauge for pressure control. 3. Electric Motor for running the gear pump ; 4 poles, 400 volt, threephase, 50 Hz., protection IP 55. 4. Hydraulic Piston controlled by the hydraulic unit through rubber hydraulic hoses. 1. Tube for transporting the compacted solid material at 45 o up to a height of 1.5 metres from the floor. 2. Inlet Hopper constructed in AISI 304 Stainless Steel. 3. Continuous Bagging System for screenings. Model Length of compaction chamber Height of compaction chamber Height (ex. conveying tube) Diameter kw Q m 3 /h HCP20 300 410 1110 200 2.2 0.7 HCP40 400 550 1250 273 3.0 1.5 HCP80 800 550 1250 273 3.0 2 HCP100 800 820 1650 457 5.0 3
SKE Spiraline Shaftless Screw Conveyor SCO 1. A specially designed stainless steel U trough conveyor used in the transporting of difficult solid and waste material 2. The materials may be stringy, sticky, varying in size, volume or dryness. Sludge, screenings, wastes, grit, wood chip, animal products, foodstuff, and drill cuttings can all be conveyed successfully. 3. The unit s shaftless spiral, running on a U liner or stainless steel wear bars, has no end or intermediate bearings, thus it can handle many materials effectively without blockages and with very little maintenance. Conveyors 1. Shaftless screw conveying section U trough, cover lids, end plates, legs, inlets and outlets constructed in AISI 304 or AISI 316 stainless steel. 2. Conveying spiral in high tensile carbon steel or AISI 304 / AISI 316 stainless steel. 3. Spiral liner: 10mm UHMDW or AISI 304 / AISI 316 stainless steel wear bars. 4. Transmission: direct coupled worm gear reducer. 1. No intermediate or end bearings in contact with sludge / screenings / effluent. 2. Inclination from 0-30 3. Low Running Speed 15-30rpm giving low wear characteristics. 4. Electric Motor: 400 Volt, 50 Hz, threephase, 1400 rpm, IP 55, insulation class F. 1. Lengthening & shortening of conveying section up to 36m to meet your specific requirements. 2. One point washing system in conveying section. 3. Square inlet or special inlet depending on the inclination or dimensions required. Model Spiral Dia Throughput Sludge @ 25% Dry Solids Throughput Screenings 0 0 15 0 30 0 0 0 15 0 30 0 SCO 150 150 1.5m 3 /h 1.1m 3 /h 0.8m 3 /h 0.5m 3 /h 0.4m 3 /h 0.3m 3 /h SCO 200 185 3.0m 3 /h 2.4m 3 /h 1.7m 3 /h 2.0m 3 0.8m 3 0.6m 3 SCO 250 240 7.0m 3 /h 5.3m 3 /h 3.9m 3 /h 2.4m 3 1.8m 3 1.1m 3 SCO 300 280 11.0m 3 /h 8.5m 3 /h 6.0m 3 /h 3.8m 3 2.8m 3 1.8m 3 SCO 400 360 23.0m 3 /h 18.0m 3 /h 13.0m 3 /h 8.0m 3 6.0m 3 3.8m 3 SCO 500 460 45.0m 3 /h 37.0m 3 /h 26.0m 3 /h 17.0m 3 12.0m 3 8.0m 3
SKE Spiraline Grit Classifier - SCL 1. SCL grit classifier is a stand alone unit designed to remove small particles of solids, grit, sand and fines from wastewater, elevating and de-watering the solids prior to disposal. 2. The effluent inlet is via the flanged connection on the top of the decanting hopper. 3. Settled solids are removed from the hopper by a low speed shaftless conveying screw and then discharged through the outlet to a suitable collecting facility. 1. De-canting hopper, shaftless screw conveying section, legs, inlet and outlet constructed in AISI 304 or AISI 316 stainless steel. 2. De-watering / conveying spiral in high tensile carbon steel or AISI 304 / AISI 316 stainless steel. 3. Transmission: direct coupled worm gear reducer. 4. Spiral liner AISI 304 / AISI 316 stainless steel wear bars. Grit Removal 1. No lower bearing so no bearings are in contact with the grit-laden liquor. 2. Capture rate: 95% of all particles above the size of 200 microns. 3. Low running speed giving a low wear characteristic. 4. Electric motor: 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. 1. Grit Washing System in the conveying section 2. Aeration System for organics separation in hopper 3. Drain Valve at hopper base for maintenance draining Model Length Height Throughput Hopper Capacity Connections In/Out SCL30 4500 2100 30m 3 /hr 0.7m 3 DN100 / DN150 - PN10 0.25 SCL80 5660 2540 80m 3 /hr 1.93m 3 DN125 / DN200 - PN10 0.25 SCL100 6100 2740 100m 3 /hr 2.92m 3 DN175 / DN250 - PN10 0.25 kw
SKE Spiraline Inlet Pre - Treatment Plant PTS 2 1. Screenings pumped into the flanged inlet are captured by a C shaped screening basket and elevated off the face of the screen by the shaftless spiral fitted with screen cleaning brushes. 2. Once captured, the screenings are elevated to a convenient disposal height along the face of the shaftless spiral. Conveyed screenings are de-watered in the compaction barrel before discharge. All filtrate is returned by flexible hose back to the effluent stream. 3. Screened liquor is discharged from the inlet tank directly into a decanting hopper where grit, sand and fines are allowed to settle out. The settled solids are removed from the hopper by a low speed shaftless conveying screw, elevating above the water level, de-watering and transferring at a convenient discharge height. 4. De-gritted liquor is allowed to weir out of the hopper and on for further processing. 5. Screenings and grit washing system in screening and conveying sections. 6. This plant is a complete pre-treatment unit, comprising of screen, washer, conveyor, compactor and classifier. 1. Self-supporting tank, inlet/outlet flanges, screen basket, shaftless conveying sections, de-canting hopper, legs, wear bars and troughs constructed in AISI 304 / AISI 316 stainless steel. 2. De-watering / conveying spirals in high tensile carbon steel or AISI 304 / AISI 316 stainless steel. 3. Transmissions: direct coupled worm gear reducers. 4. Spiral liner AISI 304 / AISI 316 stainless steel bars. 1. No lower bearing, so no bearings are in contact with screenings or liquor. 2. Sreen Baskets 0.25-0.5-1mm - 2mm wedge-wire, 3mm - 10mm perforated plate. 3. Self-supporting tank with flanged inlet/outlet, breather, access lid and fixing plates. 4. Low running speeds giving low wear characteristics. 5. Classifier capture rate 95% of all particles above the size of 200 microns. 6. Electric Motor 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. Optional Extras 1. Aeration system for organics separation in de-canting hopper. 2. Continuous bagging system for screenings. 3. Lengthening & shortening of conveying section to meet your specific disposal requirements. Combined Pre - Treatment Plants Model Length Height Throughput Hopper Capacity Wash Water kw PTS/2 30 4500 2100 30m 3 /hr 0.7m 3 1.1 & 0.37 PTS/2 50 4500 2133 50m 3 /hr 1.2m 3 1L/Sec 1.1 & 0.37 PTS/2 80 5660 2540 80m 3 /hr 1.93m 3 @ 2.5 Bar 1.1 & 0.55 PTS/2 100 6100 2740 100m 3 /hr 2.92m 3 1.1 & 0.75
SKE Spiraline Compact Treatment Plant CPS 1. The incoming effluent is pumped or flows to the STU/C, depending on the location. 2. Effluent flows through the screen. Solids are captured on the screening basket and as the screen blinds, the upstream level rises to a pre-determined level at which the screw operates and clears the screening basket. 3. While screenings are conveyed away from the screen surface to the discharge point, washing occurs in the conveying section of the conveyor. The spiral runs on heavy duty longitudinal wear bars which enable the screenings to de-water during elevation. Before screenings are discharged they are compacted in the compaction zone of the screen press. 4. Effluent passes through the screen to the hopper section where grit and organics separation takes place. 5. Grit that settles in the hopper is conveyed to one end by a shaftless screw conveyor before being lifted out of the hopper and dewatered by an inclined shaftless screw. 6. of the conveyors is controlled by timers, dependent on the site grit accumulation. 7. Treated effluent is discharged from the plant by gravity for further treatment. 1. Self-supporting tank, inlet/outlet flanges, screen basket, shaftless conveying sections, decanting hopper, legs, wear bars and troughs constructed in AISI 304 / 316 stainless steel. 2. De-watering / conveying spirals in high tensile carbon steel or AISI 304 / AISI 316 stainless steel. 3. Transmission: Direct coupled worm gear reducers. 4. Spiral liner AISI 304 / 316 stainless steel bars. 1. Bearing Structure - no lower bearing, so no bearings are in contact with screenings or liquor. 2. Screen Baskets 0.25-0.5-1mm - 2mm wedge-wire, 3mm -10mm perforated plate. 3. Self-supporting tank with flanged inlet / outlet, breather and fixing plates. 4. Low running speeds giving low wear characteristics. 5. Grit Capture Rate 95% of all particles above the size of 200 microns. 6. Electric Motor 400 Volt, 50 Hz, threephase, 1400 rpm, IP 55, insulation class F. Combined Pre - Treatment Plants Optional Extras 1. Spiral, Body and Tank material of construction available in AISI 316 stainless steel. 2. Lengthening & shortening of conveying section to meet your specific requirements. CPS models available to handle throughputs from 15 l/s up to 150 l/s.
SKE Spiraline Imported Sludge Reception SRS 1. The SRS Imported sludge reception unit is a stand alone unit designed to screen tankered sludge such as cess-pool collection and contaminated settled sludge from primary and secondary treatment. 2. Screenings are pumped from the tanker to the self-supporting tank via a quick release coupling. The screenings are captured by the C shaped screening basket and elevated off the face of the screen by the shaftless spiral. This spiral is also fitted with screen cleaning brushes which ensure the screening surface remains open. 3. Once captured the screenings are elevated to a convenient disposal height by the shaftless spiral. The spiral runs on heavy-duty longitudinal wear bars, which enable the screenings to de-water during elevation. 4. Conveyed screenings are further de-watered in the compaction barrel before discharge. All filtrate is piped back to the inlet stream. Screened sludge is discharged from the tank via its flanged outlet. 5. The screen operates by differential levels upstream and downstream, caused by the screenings captured. 6. This unit is a four in one screen, washer, conveyor and compactor. 1. Self-supporting tank, inlet/outlet flanges, screen basket, shaftless screw conveying section, legs, wear bars and outlet constructed in AISI 304 / AISI 316 stainless steel. 2. De-watering /conveying spiral in special carbon steel or AISI 304 / AISI 316 stainless steel. 3. Inlet by special control valve fitted with DN100 fast coupling. 4. Transmission direct coupled worm gear reducer. 5. Spiral liner AISI 304 / 316 stainless steel bars. Sludge Reception Units 1. Bearing structure: no lower bearing, therefore no bearings are in contact with the screenings or sludge. 2. Screen baskets 5mm-10mm perforated plate. 3. Self-supporting tank with flanged inlet/outlet, breather, access lid and fixing plates. 4. Low running speed giving low wear characteristics. 5. Electric motor 400 Volt, 50 Hz, three-phase, 1400 rpm, IP 55, insulation class F. 1. Continuous bagging system for screenings. 2. Ultra sonic level indicator. Model Length Height Throughput Outlet (Sludge) Outlet (Screenings) kw SRS50 3990 2300 50m 3 /hr DN200PN10 253mm Dia. 0.55 SRS100 4990 3220 100m 3 /hr DN200PN10 370mm Dia. 1.1
SKE Klearline Compact System for Treatment of Imported Sludge FVST 1. After connecting the tanker to the quick connection coupling, the sewage is injected into the tank. The plant starts up automatically by special sensors and begins to filter. 2. The sewage flows through the screen while the trapped solids are conveyed by special cleaning teeth to the top of the filter. The special curved shape of the bars allows expulsion of the solids and an accurate cleaning of the teeth. 3. The solids are squeezed and dewatered by a screw compactor before being conveyed to a storage container or collecting bag. 4. To remove organic particles the screw is washed by spray nozzles. 5. In case of overloads, sensors activate a gate valve that stops the sewage flowing. 1. Main structure of cold-rolled steel sheet, filtering surface made of rolled plate 30 x 4 mm, all AISI 304 stainless steel. 2. Cleaning combs made of wear-resistant plastic mounted on a special support of AISI 304 stainless steel. 3. Transmission chain in AISI 304 stainless steel, with rollers made of polyester which are selflubricating in water. 4. FVST filter with ratio-gearmotor. Compactor with worm-screw gearmotor. 5. Pneumatic gate valve with cast-iron body and AISI 304 stainless steel valve and solenoid control. 6. Fan shaped spray nozzles with on/off solenoid valve. 7. Capacity sensors for plant automation. 8. Control panel. 1. AISI 304 stainless steel tank. 2. Filter type FVST 75 100 manufactured in AISI 304 stainless steel. 3. Screw compactor manufactured in AISI 304 stainless steel. 4. Capacity sensors. 5. Pneumatic gate valve. 6. FVST filter with ratio-gearmotor, compactor with worm-screw gearmotor. 7. Electric Motor 400 Volt, 50 Hz, three-phase, 1400 rpm, degree of protection IP 55, insulation class F. Sludge Reception Units 1. Manufactured in AISI 316 stainless steel. 2. Screen dimensions can be customised to fit channel requirements. Model Width Discharge Ht From Channel Invert Comb Speed (m/min) Bar Spacing kw (FVST & SCP) FVST 75 2180 2780 2.5 3 5 0.5 & 0.185 FVST 100 2180 2780 5 3 5 1.0 & 0.185
SKE Materials Handling Equipment Materials Handling Equipment supplies a full range of materials handling equipment, as well as designing, installing and commissioning complete turnkey plants. SKE Solutions is also the sole agent for the Sodimate range of equipment. SKE Solutions supply a full range of conveying formations for sludge conveying and materials handling. This can include the transport of sludge from one or a bank of sludge dewatering units such as belt presses or centrifuges. The sludge is evenly deposited in a skip. Controls provide for the even distribution of the sludge in the skip. 1. Loading bellows Bellows for the open loading and closed loading of trucks and tankers are available. Options include dust extractor connections, double walled bellows for soft and floury materials and metal inner cones for use with granular and abrasive products. 2. Valves and control equipment Pinch valves are closed by applying a control agent, such as compressed air or water under pressure, to the sleeve. Butterfly valves are used as discharge mechanisms on bins that contain powders. 3. Conveyors Shafted conveyors range from light duty through to extra-heavy duty suitable for handling various powders and pellets. Shaftless spiral conveyors are available for handling difficult materials with a high moisture content eg. sludge or other sticky materials. 4. Other equipment SKE Solutions also supply dust collectors, vibration motors and agitators, as well as continuous mixers, batch mixers, granulators and systems for quick discharge unloading. 5. Technical support SKE Solutions technical staff can guide clients with regard to correct product selection and accurate technical specification. Bulk Powder Storage & Materials Handling
SKE Lime & Bulk Powder Storage & Handling Systems 1. The product can be blown into the silo(s) by tanker or fed by a conveyor system (SKE) or other handling system. 2. Once stored in dry conditions, a controlled discharged can be obtained using SKE aeration, vibratory or mechanical means, depending upon the product and the particular application. 3. Transfer / metering conveyors transport the powder product to the point of usage or where it can be weighed and mixed to form a slurry, prior to being dosed. 4. Under the controlled conditions, the powder can be accurately weighed under exact conditions as an integral facility of the plant. 5. In the case of a slurry, the product is mixed with a liquid (usually water) under controlled conditions. 6. The plant can be situated inside or outside. Advantages 1. Custom designed to suit the application 2. Large range of configurations to suit the requirements and space available 3. Turnkey packages to suit the customers requirements 4. Wide range of applications 5. Advice & guidance at the design stages 6. Customer care and back-up 7. Large number of installations 8. Experience 9. Reputation 10. Reliability 1. Storage Silo(s) 2. Silo discharge facilities 3. Complete silo safety systems 4. Transport & metering conveyors 5. Inherent weighing and measurement 6. Mixing and blending facilities 7. Definitive controls 8. Compact design 9. Low maintenance 10. High reliability Bulk Powder Storage & Materials Handling
SKE Bulk Solids Loading and Unloading Systems Description Dried sludge silo loading and unloading equipment, including design, installation and commissioning of complete turnkey plants. Our range includes silo loading, unloading equipment and storage systems. For difficult products such as sludge (including dewatered sludge) lorry loading and unloading systems allow a fast and efficient turn around for filling or emptying the lorry without spillages. 1. Lorry unloading 2. Conveying 3. Storage 4. Installation 5. Lorry loading plant 6. Dust/odour system 7. Training 8. & maintenance manuals 9. Commissioning Advantages 1. Custom designed to suit the application 2. Advice & guidance at the design stages 3. Customer care and backup 4. Experience 5. Reputation 6. Reliability Bulk Powder Storage & Materials Handling
SKE Sludge Stabilisation System Process Description 1. Sludge feeds into the ploughshare mixer which is internally heated to 100 c + 2. A boiler situated in the control unit provides the hot water (this can be oil or gas fired depending on availability at site) 3. Control unit to pressurise the water system, thus avoiding vaporisation. 4. Lime is transferred from the storage silo via the lime screw conveyor into the ploughshare mixer 5. The sludge is thoroughly mixed with the lime (mixer retention time 3 minutes approx) and the product deposited onto the insulated pasteurisation conveyor which has a travel time of 30 minutes from inlet to outlet. 6. From here the product is transferred by the final transfer conveyor to a waiting trailer for disposal 7. Odour emissions are ducted to the powered odour control unit which purifies by means of filters to remove hydrogen sulphide and ammonia. Other media can be used in the unit depending on the emissions. 8. One control panel located in the control unit controls the starting and monitoring of the complete plant including: a. Water Temperature b. Lime Feed Rate c. Product Inlet Temperature d. Product Outlet Temperature e. Pasteurisation Conveyor travel speed / time (variable) f. Chart Recorder to document details as required 9. The plant offers low running costs, high efficiency, reliable operation. 10. Customer service, back-up, technical expertise, advice and reliability, tailored to suit your needs. Bulk Powder Storage & Materials Handling
Note - Products which possibly may not be included: - SKE Bulk Solids Loading and Unloading Systems Products not shown which will be included: - Sodimate Amiad Filtration quality guaranteed customer satisfaction Sandholes Road Company Reg. No. N.I. 42833