REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN ASEAN. Table of Contents

REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN ASEAN Table of Contents I. Rationale for Regulation II. III. IV. Regulatory Authority Legislative Framework Mandatory V. Mode of Regulation and Types of Conformity Assessment Regimes VI. VII. VIII. Flowchart of each Member Country's Regime Voltage, Frequency and Mains Plug Configuration Contact Person 1

I. RATIONALE FOR REGULATION COUNTRY Brunei Darussalam Cambodia Indonesia Lao PDR Malaysia Myanmar Philippines Singapore Thailand Viet Nam RATIONALE FOR REGULATION Ensure safety and reliability in the supply of electricity Consumer Protection Consumer Protection Consumer's Rights and Benefits Protection. Promote and Facilitate the Producers of Goods and s Ensure safety and Consumer protection. Ensure Safety and Consumer protection. Upgrade the quality of products. Protect and safeguard the interest of consumers especially in matters of health and safety. Consumer Protection. Consumer Protection. Ensure Safety in the use of electrical products. 2

II. REGULATION BODY COUNTRY REGULATORY BODY Brunei Darussalam Ministry of Development Department of Electrical Services Cambodia Ministry of Commerce (Cambodia Import Export Inspection and Fraud Repression Department Camcontrol) Indonesia Lao PDR Ministry of Industry Mines and Energy (Department of Industrial of Cambodia ISC) Ministry of Industry and Trade. Ministry of Energy and Mineral Resources. Science, Technology and Environment Agency Department of Intellectual Property, Standardization and Metrology Malaysia Energy Commission (Suruhanjaya Tenaga) Myanmar Ministry of Industry (1) Directorate of Industrial Supervision and Inspection Electrical Inspection Department Philippines Bureau of (BPS) under the Department of Trade and Industry (DTI). Singapore Thailand Viet Nam, ivity and Innovation Board (or SPRING Singapore in short) Thai Industrial Institute (TISI) under the Ministry of Industry. Directorate for and Quality (STAMEQ) under Ministry of Science and Technology (MOST) 3

III. LEGISLATIVE FRAMEWORK COUNTRY LEGISLATIVE FRAMEWORK Brunei Darussalam Electricity Act (1984) Cambodia Law on the management of quality and safety of product and services (2000) Indonesia Act No. 8 / 1999 Subdecree No.42 on Industrial of Cambodia (2001) Lao PDR Decree of the Prime Minister regarding the Management on and Quality of s and the Metrology Management Quality Inspection of Import Goods Malaysia Electricity Supply Act 1990; and Electricity Regulations 1994 Myanmar Electricity Law (1984) Philippines Republic Act 4109 Singapore Consumer Protection (Safety Requirements) Regulations 2002* which is based on the Consumer Protection (Trade Descriptions and Safety Requirements) Act (Chapter 53) * Consumer Protection (Safety Requirements) Regulations 1991 has been revoked and replaced by Regulations 2002. 4

COUNTRY LEGISLATIVE FRAMEWORK Thailand Industrial Act. (1968) Viet Nam Act on Quality issued by the National Assembly Decision on the Ministry of Science and Technology on Safety Certification. Decision of the Ministry of Science and Technology on State Inspection of ImportExport s Quality. IV. MANDATORY Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Brunei Darussalam No Mandatory standards Country Cambodia 01 Fuses/Fuse Links up to 63 A type or grouping Domestic Please tick box if Relevant International Extent of Alignment CS 0030:2003 IEC 602691,Ed.3:1998 State reason if MOD 5

02 Electrical Hair Dryers 03 Electrical Coffee/Tea Makers 04 Electrical Deep Fryers 05 Electrical Food Steamers 06 Electrical Slow Cookers CS 0010:2003 CS 0011:2003 CS 0010:2003 CS 0012:2003 CS 0010:2003 CS 0013:2003 CS 0010:2003 CS 0012:2003 CS 0010:2003 CS 0012:2003 07 Electrical Iron CS 0010:2003 08 Electrical Blenders 09 Electric Food Processors CS 0014:2003 CS 0010:2003 CS 0015:2003 CS 0010:2003 CS 0015:2003 IEC 603351, ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335223 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335215 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335213 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335215 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335215 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033523 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335214 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335214 6

10 Electric Juice Extractors 11 Electric Grinders 12 Electric Mixers CS 0010:2003 13 Electric Microwave Ovens 14 Electric ventilating fan & regulators CS 0010:2003 IEC 603351 CS 0015:2003 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335214 CS 0010:2003 IEC 603351 ed.3:1991+am.1&2:19 CS 0015:2003 94+Am.2;1999 IEC 60335214 IEC 603351 ed.3:1991+am.1&2:19 CS 0015:2003 94+Am.2;1999 IEC 60335214 CS 0010:2003 IEC 603351 ed.3:1991+am.1&2:19 CS 0016:2003 94+Am.2;1999 IEC 60335225 CS 0017:2003 IEC 60335280 15 Television CS 0029:2003 IEC 60065 16 Carpet CS 0010:2003 Cleaners 17 Vacuum Cleaners and accessories 18 Electric Washing Machines CS 0018:2003 CS 0010:2003 CS 0018:2003 CS 0010:2003 CS 0019:2003 CS 0020:2003 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033522 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033522 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033527 IEC 6033524 7

19 Electric Freezers 20 Electric Rice Cookers 21 Electric Sewing Machine 22 Electric Soldering Irons 23 Electric Grinders ( up to 100 mm ) CS 0010:2003 CS 0011:2003 CS 0010:2003 CS 0012:2003 CS 0010:2003 CS 0022:2003 CS 0010:2003 CS 0023:2003 CS 0042:2003 CS 0048:2003 24 Refrigerators CS 0021:2003 CS 0021:2003 25 3pin 13amp CS 0049:2003 socketoutlet CS 0051:2003 26 Incandescent lamp IEC 603351, ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 603352 24,Ed.4:1997 + Am.2:1999 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335215 IEC 603351, ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 603352 28,Ed.3:1994 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 60335245:1996 IEC 607451,Ed.1 :1989 IEC 607452 3,Ed.11984 + Am.1:1995 IEC 60335224:1992 IEC 60335224:2000 IEC 60335221:1997 IEC 608841 CS 0006:2003 IEC 60064:1993 IEC 604321:1999 NEQ 8

27 PVC insulated copper cable 28 3pin rectangular type 13 amp.plug 29 3pin round type 15 mp.plug 30 Multiway adaptors 31 General purpose switches CS 0024:2003 CS 0025:2003 CS 0017:2003 CS 0051:2003 IEC 60227 1:1993,Am.1(1995),A m.2(1998) IEC 602272:1997 IEC 60335280:1997 IEC 608841 CS 0017:2003 IEC 60335280:1997 CS 0017:2003 IEC 60335280:1997 CS 0026:2003 IEC 606691 32 Cassette player CS 0029:2003 IEC 60065 33 Portable radio cassette player/recorder CS 0029:2003 IEC 60065 34 Video compact disc player 35 Home computer system(inclusi ve of monitor, printer, speaker, other operated accessories and mains CS 0029:2003 IEC 60065 CS 0047:2003 IEC 60950:1991 9

36 PVC insulated and sheated cable with 300/500 V rated voltage 37 PVC insulated wire with rated voltage 450/750 V 38 Self ballast lamp for general lighting service 39 Lowvoltage distribution link fuses 40 Lampholder for tubular fluorescent lamps 41 Staterhaolder for tubular fluorescent lamps 42 Miniature Circuit Breaker 43 Electrical Standing Lamps 44 Electrical Table Lamps CS 0050:2003 IEC 502:1994 CS 0050:2003 IEC 502:1983 CS 0027:2003 IEC 60968:1988 CS 0030:2003 IEC 602691:1998 CS 0031:2003 IEC 60400 CS 0031:2003 IEC 60400 CS 0032:2003 IEC 60898 CS 0034:2003 CS 0035:2003 CS 0034:2003 CS 0035:2003 IEC 605981 IEC 6059824 IEC 605981 IEC 6059824 10

45 Electrical Hand Lamps 46 Electrical MultiPurpose Cookers 47 Electrical Hair Clippers 48 Electrical Shavers 49 Electrical Fixed Immersion Heaters 50 Portable Immersion Heaters 51 Electrical Portable Ovens CS 0034:2003 CS 0036:2003 CS 0010:2003 CS 0037:2003 CS 0013:2003 CS 0012:2003 CS 0010:2003 CS 0033:2003 CS 0010:2003 CS 0033:2003 CS 0010:2003 CS 0038:2003 CS 0010:2003 CS 0039:2003 CS 0010:2003 CS 0037:2003 IEC 605981,Ed.4:1996 IEC 605982 8,Ed.2:1996 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033529 IEC 60335213 IEC 60335215 IEC 603351, ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 603352 8,Ed.4:199201 IEC 603351,Ed.3 + Am.1:1994 +Am.2:1999 IEC 603352 8,Ed.4:199201 IEC 603351, ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 603352 73,Ed.1:1994 IEC 603351, ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 603352 74,Ed.1:1994 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033529 11

52 Electrical Grillers 53 Electrical Roasters 54 Electrical ceiling fan and regulator 55 Electrical movinglouvre fan and regulator 56 Electric Table Fan and regulators 57 Electrical wall fan and regulators 58 Lighting Chains CS 0010:2003 CS 0037:2003 CS 001:2003 CS 0037:2003 CS 0045:2003 CS 0040:2003 CS 0045:2003 CS 0040:2003 CS 0045:2003 CS 0040:2003 CS 0045:2003 CS 0040:2003 CS 0034:2003 CS 0041:2003 59 Electric Circular Saws CS 0042:2003 and Circular CS 0028:2003 Knives 60 Electric Drill CS 0042:2003 CS 0043:2003 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033529 IEC 603351 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC 6033529 IEC 60335280 IEC 60879 IEC 60335280 IEC 60879 IEC 60335280 IEC 60879 IEC 60335280 IEC 60879 IEC 60598 1,Ed.5:19999 IEC 605982 20,Ed.2:1996 + Am.1:199801 IEC 607451,Ed.1:1989 + Am.1:1992 IEC 607452 5,Ed.2:1993 IEC 607451,Ed.1:1989 IEC 6074521 12

61 Adapter CS 0044:2003 CS 0046:2003 CS 0029:2003 CS 0047:2003 IEC 60742:1983 + Am.1+ Am2.:1992 IEC 6155826:1996 IEC 60065:19998 IEC 60950:1999 62 Fluorescent Lamp: Safety requirements CS 0008:2003 IEC 60081:1997 NEQ Country Indonesia Incandescent lamps type or grouping Domestic Please tick box if Relevant SNI 0435601994 V JIS C 421 International Extent of Alignment State reason if MOD Alternating current ballast for fluorescent lamp Drycells batteries Compound for insulation of electric wire and cable with 1 kv up to 30 kv rated voltage SNI 0435611994 V JIS C 108 SNI 0420511990 V IEC 86, JIS C 8501, ANSI 181 SNI 0426971992 V IEC 5021983 13

Country type or grouping Domestic Please tick box if PVC insulated and sheated cable with 300/500 V rated voltage Relevant SNI 0426991999 V IEC 5021994 International Extent of Alignment State reason if MOD Insulated and PVC covered power cable for ground identification volatage 0,6/1 kv(nyy/nayy) Indonesia PVC insulated and sheated, steel or aluminium wire shielded ground cables rated voltage 0,6/1 kv(nyf Gb Y/ NAYFGbY/NXY RGbY/NARGbY/ NYRY/NAYRY) Indonesia PVC insulated and sheated underground cable, steel or aluminium band shielded with 0,6/1 kv rated voltage SNI 0427011999 V IEC 5021994 SNI 0427001999 V IEC 5021 SNI 0461221999 V 14

Country Indonesia PVC insulated and sheated flexible cable with 500 V rated voltage (NYMHY) type or grouping Domestic Please tick box if SNI 0432341992 V Relevant International Extent of Alignment State reason if MOD Indonesia PVC insulated and sheated flexible cable with 500 V rated voltage (NYMHY oval) Indonesia PVC insulated and sheated flexible cable with 1000V rated voltage Indonesia PVC insulated and sheated flexible double wire and triple wire cable with rated voltage up to 380 V Indonesia PVC insulated and sheated double wire up to five wire cable with rated voltage up to 380 V SNI 0432351992 V SNI 0432361992 V SNI 0432371992 V SNI 043238 1992 V 15

Country Indonesia PVC insulated wire rated voltage with 450/750 V type or grouping Domestic Please tick box if Relevant SNI 0426981992 V IEC 5021983 International Extent of Alignment State reason if MOD Indonesia Selfballast lamp for general lighting service SNI 046504 2001 V IEC 609681988 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Lao PDR No standards 16

Country Malaysia 1 PLUG TOP (PLUGS) type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Two pole plugs & supply cords 13A Fused plugs 15A Fused plugs Adaptors (multiway) MS 1578:2003 BS EN 50075 MS 589:PT.1:1997 BS 1363: PT.1 MS 1577:2003 BS 546 MS 589: PT.3:1997 BS 1363:PT.3 Cable Connectors No Corresponding MS IEC 609981 IEC 6099821 IEC 6099822 IEC 6099823 IEC 6099824 IEC 6099825 Appliance Connectors 2 SWITCHES AND DIMMERS MS IEC 603201:1996 IEC 603201 General purpose switches MS 616:PT.1:1998 IEC 606691 MOD Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) 17

Country type or grouping Domestic Please tick box if Electronic switches Malaysia Remotecontrol switches Relevant International Extent of Alignment MS 616:PT.2:Sect.1:2000 IEC 6066921 MOD MS 616:PT.2:Sect.2:2000 IEC 6066922 MOD Malaysia Time Delay Switches MS 616:PT.2:Sect.3:2000 IEC 6066923 MOD 3 SOCKET OUTLES 15A AND BELOW (with or without elcb/rcd) State reason if MOD Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) Electric Shaver Socket Outlets Isolating Transformer MS EN 60742:1998 EN 60742 IEC 6155826 MS EN 60742:1998 EN 60742 IEC 6155826 NEQ NEQ 13A Portable Switched Socket Outlets 13A Unswitched Socket Outlets 15A Socket Outlets MS 589:PT.2:1997 BS 1363:PT.2 MS 589:PT.2:1997 BS 1363:PT.2 MS 1577:2003 BS 546 ACDC or ACAC Converter (Adaptor) MS EN 60742:1998 EN 60742 IEC 6155826 IEC 60950 (IT Equip.) NEQ NEQ 18

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Portable 2Pin Socket Outlets MS 1579:2003 SS 448:2001 Cooker Control Units 4 LAMPHOLDERS Lampholders for tubular fluorescent lamps Staterholders for tubular fluorescent lamps No Corresponding MS BS 4177 : 1992 MS IEC 60400:1999 IEC 60400 MS IEC 60400:1999 IEC 60400 5 CEILING ROSES 6 BAYONET CAPS AND MULTIWAYS ADAPTORS MS 770:1982 Bayonet Lampholders MS 769:1982 Malaysia Bayonet Adaptors MS 769:1982 7 FLUORESCENT LAMPS FITTING EXCLUDING TUBES IF IMPORTED SEPARATELY Fixed general purpose luminaires MS IEC 605981:1997 IEC 60598 1 MS IEC 6059821:1997 IEC 6059821 19

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Recessed luminaires MS IEC 605981:1997 IEC 60598 1 MS IEC 6059822:1998 IEC 6059822 Lampholders / Starterholders MS IEC 60400:1999 IEC 60400 Glowstarters for tubular fluorescent MS IEC 60155: 1996 IEC 60155 8 CAPACITORS FOR FLUORESCENT LAMPS Capacitors for use in tubular fluorescent lamp circuit MS IEC 61048:1999 MS IEC 61049:1999 IEC 61048 IEC 61049 9 BALLAST FOR FLUORESCENT Malaysia Ballast for tubular fluorescent lamps MS 141 :PT.1:1992 & MS 141 :PT.2:1992 IEC 60920 IEC 60921 MOD MOD Additional ballast lost requirement Electronic Ballast MS IEC 60928:1995 MS IEC 60929:1995 IEC 60928 IEC 60929 20

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD 10 CIRCUIT BREAKER INCLUDING AC CURRENT OPERATED LEAKAGE CIRCUIT BREAKERS AND MINIATURE CIRCUIT BREAKERS Residual Current Circuit Breakers MS IEC 610081:2003 IEC 10081, Ed.2 Miniature Circuit Breaker (MCB) MS IEC 60898:1998 IEC 60898 RCBO s No Corresponding MS IEC 610091 IEC 6100921 IEC 6100922 Fuse Base & Carrier up to 32A Fuses/Fuse Links up to 63A No Corresponding MS IEC 602691, Ed.3 IEC 602692, No Corresponding MS IEC 6026921 IEC 602693, IEC 6026931 11 WATER HEATER INCLUDING HEATING ELEMENTS IF IMPORTED SEPARATELY Electric Stationary Instantaneous Water Heaters MS 472 :PT.3 :SEC.3.1 :1986 BS 3456:PT.3, SEC. 3.9 IEC 603351 IEC 603352 NEQ NEQ Electric Storage Water Heaters MS IEC 603351:1995 MS IEC 60335221:2000 IEC 603351 IEC 60335221 21

Country type or grouping Domestic Please tick box if 12 HAND OPERATED HAIR DRYERS Relevant International Extent of Alignment State reason if MOD Malaysia Electric Hair Dryers MS IEC 3351:1995 IEC 603351 MS IEC 60335223:1999 IEC 60335223 Electric Hair Styling Sets MS IEC 3351:1995 IEC 603351 MS IEC 60335223:1999 IEC 60335223 13 DOMESTIC LIGHT FITTINGS HAVING ACCESSIBLE METAL PARTS Electric Standing Lamps MS IEC 605981:1997 IEC 605981 MS IEC 6059824:1997 IEC 6059824 Electric Table Lamps MS IEC 605981:1997 IEC 605981 MS IEC 6059824:1997 IEC 6059824 Electric Hand Lamps IEC 605981, Ed.4:1996 IEC 6059828, Ed.2:1996 IEC 605981, Ed.4 IEC 6059828, Ed.2 22

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment 14 ELECTRIC KETTLE INCLUDING HEATING ELEMENTS IF IMPORTED SEPARATELY State reason if MOD Malaysia Electric Coffee MS IEC 603351:1995 IEC 603351 / Tea Makers MS IEC 60335215:1999 IEC 60335215 Electric Deep Fryers MS IEC 3351:1995 IEC 603351 MS IEC 335213:1995 IEC 60335213 Electric Egg Boilers MS IEC 3351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 Electric Jugs MS IEC 3351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 23

Country Malaysia Electric Food Steamers type or grouping Domestic Please tick box if MS IEC 603351:1995 Relevant International Extent of Alignment State reason if MOD IEC 603351 MS IEC 60335215:1999 IEC 60335215 Electric Warming Plates No Corresponding MS IEC 603351 IEC 60335212, Ed. 4 Electric Slow Cookers MS IEC 603351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 Electric Steam Boats MS IEC 603351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 Electric Built in Hobs MS IEC 603351:1995 IEC 603351 MS IEC 335236:1995 IEC 60335236 Malaysia Electric Kettles MS IEC 3351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 24

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Electric Airpots MS IEC 603351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 Electric Steam Generator Appliances MS IEC 603351:1995 IEC 603351 MS IEC 60335215:1999 IEC 60335215 Electric Aroma Vaporisers No corresponding MS IEC 603351 IEC 603352101 Electric MS IEC 603351:1995 Heating Elements for Kettles MS IEC 60335215:1999 15 ELECTRIC SMOOTHING IRONS Electric Irons MS IEC 603351:1995 MS IEC 6033523:1995 16 ELECTRIC SHAVERS IEC 603351 IEC 60335215 IEC 603351 IEC 6033523 Malaysia Electric Hair Clippers MS IEC 603351:1995 MS IEC 6033528:2002 IEC 603351, Ed.3 IEC 6033528, Ed 4: Electric Shavers MS IEC 603351:1995 MS IEC 6033528:2002 IEC 603351, Ed.3 IEC 33528, Ed 4 25

Country type or grouping Domestic Please tick box if 17 FOOD MIXERS/BLENDERS Relevant International Extent of Alignment State reason if MOD Electric Blenders MS IEC 603351:1995 MS IEC 60335214:1996 IEC 603351 IEC 60335214 Electric Choppers MS IEC 603351:1995 MS IEC 60335214:1996 IEC 603351 IEC 60335214 Malaysia Electric Food Processors MS IEC 603351:1995 MS IEC 60335214:1996 IEC 603351 IEC 60335214 Electric Juice Extractors MS IEC 603351:1995 MS IEC 60335214:1996 IEC 603351 IEC 60335214 Electric Grinders MS IEC 603351:1995 MS IEC 60335214:1996 IEC 603351 IEC 60335214 Electric Mixers MS IEC 603351:1995 MS IEC 60335214:1996 18 IMMERSION WATER HEATERS IEC 603351 IEC 60335214 Electric Fixed Immersion Heaters MS IEC 603351:1995 MS IEC 60335273:1996 IEC 603351, Ed.3 IEC 60335273, Ed.1 Malaysia Portable Immersion Heater MS IEC 603351:1995 MS IEC 60335274:1996 IEC 603351, Ed.3 IEC 60335274, Ed.1 26

Country type or grouping Domestic Please tick box if 19 HIFI SETS Relevant International Extent of Alignment State reason if MOD Subwoofer MS IEC 60065:1997 IEC 60065 Amplifier MS IEC 60065:1997 IEC 60065 Cassette Player MS IEC 60065:1997 IEC 60065 Equalizers/ Mixers MS IEC 60065:1997 IEC 60065 HiFi System MS IEC 60065:1997 IEC 60065 Karaoke MS IEC 60065:1997 IEC 60065 Laser Disc Player MS IEC 60065:1997 IEC 60065 PA System MS IEC 60065:1997 IEC 60065 Portable HiFi System Portable RadioCassette Player / Recorder MS IEC 60065:1997 IEC 60065 MS IEC 60065:1997 IEC 60065 Radio MS IEC 60065:1997 IEC 60065 Radio Alarm MS IEC 60065:1997 IEC 60065 Malaysia Tuner / Receiver Turn tables / Record Players MS IEC 60065:1997 IEC 60065 MS IEC 60065:1997 IEC 60065 27

Country type or grouping Domestic Please tick box if Compact Disc Players Relevant International Extent of Alignment State reason if MOD MS IEC 60065:1997 IEC 60065 20 MOSQUITO MATT VAPORISERS 21 TOASTERS/OVENS MS IEC 603351:1995 IEC 603351 IEC 603352101 Electric Bread Makers MS IEC 603351:1995 MS IEC 6033529:1995 MS IEC 603351 IEC 6033529 Electric Bread Toasters MS IEC 603351:1995 MS IEC 6033529:1995 MS IEC 603351 IEC 6033529 Electric Portable Ovens MS IEC 603351:1995 MS IEC 6033529:1995 MS IEC 603351 IEC 6033529 Electric Grillers MS IEC 603351:1995 MS IEC 6033529:1995 MS IEC 603351 IEC 6033529 Malaysia Electric Microwave Ovens MS IEC 603351:1995 IEC 603351 MS IEC 60335225:1995 IEC 60335225 Electric Sandwich Makers / Waffle Makers MS IEC 603351:1995 MS IEC 6033529:1995 MS IEC 603351 IEC 6033529 28

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Electric Stationary Electric Ovens MS IEC 603351:1995 IEC 603351 MS IEC 6033526:1999 IEC 6033526 Electric Roasters MS IEC 603351:1995 MS IEC 603351 22 FANS Electric movinglouvre fans & regulators Electric ceiling fans & regulators Malaysia Electric ventilating fans & regulators Electric auto fans & regulators MS IEC 6033529:1995 MS IEC 603351 MS 1219 : 2002 MS 1220 : 2001 MS IEC 603351 MS 1219 : 2002 MS 1220 : 2001 MS IEC 603351 MS 1219 : 2002 MS IEC 603351 MS 1219 : 2002 MS 1220 : 2001 IEC 6033529 IEC 603351 IEC 60335280 IEC 60879 IEC 603351 IEC 60335280 IEC 60879 MS IEC 603351 IEC 60335280 IEC 603351 IEC 60335280 IEC 60879 MOD MOD MOD MOD MOD MOD MOD MS 1219: New requirement for detachable part, temperature marking, maintenance instruction, moisture resistance, supply connection, external flexible cord and mechanical strength MS 1220: 1) Cl 7.2: statement with at least five running positions is replaced by with at least three running positions 2) Cl 10.3.2: Rating of frequency is defined to suit local conditions 29

Country type or grouping Domestic Please tick box if Electric pedestal fans & regulators Electric table fans & regulators Electric wall fans & regulators Electric range hoods MS IEC 603351 MS 1219 : 2002 MS 1220 : 2001 MS IEC 603351 MS 1219 : 2002 MS 1220 : 2001 MS IEC 603351 MS 1219 : 2002 MS 1220 : 2001 Relevant International Extent of Alignment IEC 603351 IEC 60335280 IEC 60879 IEC 603351 IEC 60335280 IEC 60879 IEC 603351 IEC 60335280 IEC 60879 No Corresponding MS IEC 603351, Ed.3 IEC 60335231, Ed.2 MOD MOD MOD MOD MOD MOD State reason if MOD MS 1219: New requirement for detachable part, temperature marking, maintenance instruction, moisture resistance, supply connection, external flexible cord and mechanical strength MS 1220: 3) Cl 7.2: statement with at least five running positions is replaced by with at least three running positions 4) Cl 10.3.2: Rating of frequency is defined to suit local conditions Malaysia Electric Air Coolers 23 TELEVISION No Corresponding MS IEC 603351 IEC 60335298 Television MS IEC 60065 : 1997 IEC 60065 Projection Television MS IEC 60065 : 1997 IEC 60065 30

Country type or grouping Domestic Please tick box if 24 VACUUM CLEANERS Relevant International Extent of Alignment State reason if MOD Carpet Cleaners MS IEC 603351 : 1995 IEC 603351 MS IEC 6033522 : 1995 IEC 6033522 Vacuum MS IEC 603351 : 1995 Cleaners & Accessories MS IEC 6033522 : 1995 25 VIDEO PLAYER IEC 603351 IEC 6033522 Video compact disc players Video Cassette Recorder / Players Digital versatile disc players Video Rewinder MS IEC 60065 : 1997 IEC 60065 MS IEC 60065 : 1997 IEC 60065 MS IEC 60065 : 1997 IEC 60065 MS IEC 60065 : 1997 IEC 60065 31

Country Malaysia Children Video Games type or grouping Domestic Please tick box if 26 WASHING MACHINES Relevant International Extent of Alignment MS IEC 60065 : 1997 IEC 60065 State reason if MOD Electric Cloth Dryers No Corresponding MS IEC 3351 IEC 335243, Ed. 2 Electric Washing Machines MS IEC 603351 : 1995 MS IEC 6033524 : 1995 IEC 603351 IEC 6033527 MS IEC 6033527 : 1995 IEC 6033524 27 REFRIGERATORS Malaysia Electric Refrigerators MS IEC 603351 : 1995 MS IEC 60335224 : 2002 IEC 603351, IEC 335224 Electric Freezers MS IEC 603351 : 1995 MS IEC 60335224 : 2002 IEC 603351, IEC 335224 Malaysia Electric Minibars MS IEC 603351 : 1999 MS IEC 60335224 : 1999 IEC 603351, IEC 335224 28 ELECTRIC RICE COOKER MS IEC 603351 : 1995 IEC 603351 MS IEC 60335215 : 1999 IEC 60335215 32

Country type or grouping Domestic Please tick box if 29 LIGHTING CHAINS Relevant International Extent of Alignment State reason if MOD Lighting chains MS IEC 605981 : 1997 MS IEC 60598220 : 1998 30 DOMESTIC POWER TOOLS IEC 605981, Ed. IEC 60598220, Ed. Electric Circular Saws and circular knives (Cutting Blade up to 160 mm) No Corresponding MS IEC 607451, IEC 6074525, Malaysia Electric Drills (Drill bit size up to 10 mm) No Corresponding MS IEC 607451 IEC 6074521 Electric Sewing Machines MS IEC 603351: 1995 MS IEC 60335228 : 1996 IEC 603351, Ed. 3 IEC 60335228, Ed. 3 Electric Soldering Irons MS IEC 603351: 1991 MS IEC 60335245 : 1996 IEC 603351 IEC 60335245 Electric Grinders (up to 100 mm) No Corresponding MS IEC 607451, IEC 6074523 Electric spray guns for nonflammable liquids (up to 100 bars) No Corresponding MS IEC 607451, IEC 6074527, 33

Country Malaysia Electric Jig and Sabre Saws (up to 60 mm) type or grouping Domestic Please tick box if No Corresponding MS Relevant International IEC 607451, IEC 60745211, Extent of Alignment State reason if MOD Electric hedge trimmers and Grass shears (up to 750 W) No Corresponding MS IEC 607451, IEC 60745215 Electric Planers (up to 500 W) No Corresponding MS IEC 607451 IEC 60745214 Portable Battery Chargers (up to 12V) MS IEC 603351:1995 MS IEC 60335229:1996 IEC 603351:1995 IEC 60335229 Electric Routers and trimmers (up to 500 W) No Corresponding MS IEC 607451, IEC 60745217, Electric Sanders (up to 300 W) Malaysia Trimmers (up to 300 W) No Corresponding MS IEC 607451 IEC 6074524, No Corresponding MS IEC 607451 IEC 60745215 34

Country type or grouping Domestic Please tick box if Relevant International 31 WIRES / CABLES / CORDS (nonarmoured) 0.5 sq mm35 sq. mm Extent of Alignment State reason if MOD Insulated flexible cords and cable MS 140 : 1987 BS 6500 PVCinsulated cable (nonarmoured) for electric power and supply MS 136 : 1995 MS 140: 1987 BS 6004 BS 6004 Polyvinyl chloride Insulated flexible cords Rubber insulated cord and flexible cables MS 140:1987 IEC 602271, IEC 602275, MS 140:1987 BS 6500 IEC 602451 IEC 602454, NEQ NEQ NEQ NEQ 35

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Myanmar No Mandatory standards Country Philippines Ballast for tubular fluorescent lamps Safety type or grouping Domestic Please tick box if PNS 121:1996 Amd. 02:1997 Relevant International IEC 920:1990 Amd. 01:1993 Amd. 02:1995 Extent of Alignment State reason if MOD Ballast for tubular fluorescent lamps Performance PNS 122:1996 Amd. 01 & 02:1997 IEC 921:1990 Amd. 01:1990 Amd. 02:1994 Class H Fuses PNS 13:1999 UL 198B:1995 Note: Adopted IEC 2691 3 but subject to implementation. PVC insulated electric copper wires and cables PNS 35:1996 IEC 228:1978 Not equivalent 36

Country Philippines Tungsten filament lamps for domestic and similar general lighting purposes Safety type or grouping Domestic Please tick box if Relevant International PNS 381:1995 IEC 4321:1993 And. 01:1995 Extent of Alignment State reason if MOD Tungsten filament lamps for domestic and similar general lighting purposes Performance Lamp holders and starter holders for tubular fluorescent lamps PNS 382:1995 IEC 64:1993 PNS 42:1997 IEC 400:1996 Glowstarters for fluorescent lamps PNS 45:1997 Amd. 01:1997 IEC 155:1993 Amd. 01:1995 Fuseholders specifications Snap switches for general use PVC tapes for electrical insulation PNS 56:1996 ANSI/UL 512:1992 PNS 57:1996 UL 20:1995 PNS 79:1992 IEC 4543 NEQ Note: IEC was already adopted subject to implementation. 37

Country Philippines Edison Screw lamp holders type or grouping Domestic Please tick box if Relevant International PNS 80:1997 IEC 238:1996 Extent of Alignment State reason if MOD Ballast for high pressure mercury vapour lamp PNS 105:1986 Knife switches PNS 118:1992 AC supplied electronic ballast for tubular fluorescent lamps Safety PNS 1351:1997 IEC 928:199502 AC supplied electronic ballast for tubular fluorescent lamps Performance PNS 1352:1993 Amd. 01 & 02: 1997 IEC 929:1990 Amd. 01:1994 & 02:1996 Polyvinyl chloride insulated flexible cords Lighting sets using miniature and subminiature lamps for decorative purposes for indoor use PNS 163:1994 IEC 227 NEQ Note: PNS is single sheathed while IEC is double sheathed. PNS 189:2000 38

Country Philippines Non ducted air conditioners and heat pumps testing and rating for performance type or grouping Domestic Please tick box if PNS 240:1998 Amd. 01:2000 Relevant International ISO 5151:1994 Extent of Alignment State reason if MOD Safety requirements for electric irons PNS 2541:1994 Amd. 01:2000 IEC 33523:1993 Amd. 01:2000 Safety requirements for appliances for heating liquids Household appliances mains operated electronic appliance Safety Safety requirements for toasters, grills, roasters and similar appliances PNS 255:1996 IEC 335215:1995 PNS 256:1999 IEC 65:1998 PNS 272:1996 IEC33529:1993 39

Country Philippines Nonducted air conditioners Energy Efficiency Ratio (EER) and labelling requirements type or grouping Domestic Please tick box if Relevant International PNS 3961:1998 Extent of Alignment State reason if MOD Refrigerators and freezers Energy Efficiency Factor (EEF) and labelling requirements Moulded case circuit breakers Selfballasted lamps for general lighting services Safety Selfballasted lamps for general lighting services Performance PNS 3962:1997 PNS 519:1991 PNS 6031:1993 IEC 968:1988 PNS 6032:1993 IEC 969:1988 40

Country Philippines General Requirements for safety of household and similar electrical appliances type or grouping Domestic Please tick box if Relevant International PNS 1079:1994 IEC 3351:1991 Amd. 01:1994 Extent of Alignment State reason if MOD Safety requirements for vacuum cleaners and water suction cleaning appliances Safety requirements for kitchen machines Singlecapped fluorescent lamps Performance PNS 1169:1993 IEC33522:1993 PNS 1244:1994 IEC335214:1984 PNS 1261:1995 IEC 901:1992 Luminaires PNS 1328:1996 IEC 5981:1992 Plugs and socket outlets for households and similar purposes General requirements PNS 14861:1996 IEC 8841:1994 41

Country Philippines Safety requirements for storage water heaters type or grouping Domestic Please tick box if PNS 1558:1997 Amd. 01,02,03: 1997 Relevant International IEC335221:1989 Amd. 01,02:1990 Amd. 03:1992 Extent of Alignment State reason if MOD Plugs and socket outlets for domestic and similar general use standards Capacitors for use in tubular fluorescent and other discharge lamps circuits Safety Capacitors for use in tubular fluorescent and other discharge lamps circuits Performance Safety requirements for electric ironers Safety requirements for spin extractors Boxes for rigid metal conduits PNS 1572:1997 IEC 83:1975 MOD Put another column for configuration of plugs to meet Philippine condition. PNS 1574:1997 IEC 1048:1991 PNS 1575:1997 IEC 1049:1991 PNS 1679:1998 IEC 335244:1987 PNS 1680:1988 IEC 33524:1993 PNS 1829:1999 JISC 8336:1991 42

Country Philippines Safety requirements for stationary cooking ranges, hobs, ovens and similar appliances type or grouping Domestic Please tick box if Relevant International PNS IEC 6033526:2000 IEC 6033526:2000 (IEC Published 1998) Extent of Alignment State reason if MOD Safety requirements for washing machines PNS IEC 6033527:2000 IEC 6033527:2000 (IEC Published 1998) MOD Class 01appliance is allowed. Safety requirements for refrigerating appliances and ice makers PNS IEC 603352 24:2000 IEC 60335224:2000 (IEC Published 1999) Safety requirements for microwave ovens PNS IEC 603352 25:2000 IEC 60335225:2000 (IEC Published 1998) Safety requirements for range hoods PNS IEC 603352 31:2000 IEC 60335231:2000 (IEC Published 1995) Safety requirements for massage appliances PNS IEC 603352 32:2000 IEC 60335232:2000 (IEC Published 1993) 43

Country Philippines Safety requirements for motor compressors type or grouping Domestic Please tick box if PNS IEC 603352 34:2000 Relevant International IEC 60335234:2000 (IEC Published 1998) Extent of Alignment State reason if MOD Safety requirements for instantaneous water heaters PNS IEC 603352 35:2000 IEC 60335235:2000 (IEC Published 1997) Safety requirements for electrical heat pumps airconditioners and dehumidifiers PNS IEC 603352 40:2000 IEC 60335240:2000 (IEC Published 1995) Safety requirements for portable immersion heaters PNS IEC 603352 74:2000 IEC 60335274:2000 (IEC Published 1994) Safety requirements for Fans PNS IEC 603352 80:2000 IEC 60335280:2000 (IEC Published 1997) Double capped fluorescent lamps Performance PNS IEC 60081:2001 IEC 60081:2001 44

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment Singapore 41 1Air cooler No corresponding SS IEC 60335298 :1997 State reason if MOD 2Adaptor No corresponding SS IEC 60742 :1983 with Amendments 1&2 (1992) Electrical appliances or IEC 6155826: 1999 SS 143 : 1988 with A1 & A2 or SS 143 : 2000 (applicable for electronic appliances) IEC 60065 :1985 with A1, 2, & 3 (Electronic appliances) or IEC 60065: 1998 SS 337:1997 (applicable for computer / telephonic appliances) IEC 60950 :1991 with A1, 2, 3 & 4 Computer / telephonic appliances or IEC 60950: 1999 MOD Humidity test under tropical conditions 3Any other audio products SS 143 : 1988 with A1 & A2 or SS 143 : 2000 IEC 60065 :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 4Cooking range SS 146: Part 2: 7: 1988 with A1 or SS 146:Part 2:7:1999 IEC 6033526 :1986 or IEC 6033526 :1997 5Coffee maker, slow cooker, steam boat and similar appliances SS 146 Part 2:2 :1997 IEC 60335215 :1986 or IEC 60335215 :1995 45

Country Singapore 6Decorative lighting fixture type or grouping Domestic Please tick box if SS 263: Part 10: 1990 or SS 263 Part 10 : 2000 Relevant International IEC 60598220 :1982 with Amendment 1 (1987) & Amendment 2 (1992) or IEC 60598220 :1998 Extent of Alignment State reason if MOD 7Hairdryer SS 146: Part 2: 9: 1994 with A1 or SS146:Part 2:9:1997 IEC 60335223 :1986 or IEC 60335223 :1996 8Home computer system (inclusive of monitor, printer, speaker and other mains operated accessories) 9Highfidelity set SS 337:1997 IEC 60950 :1991 with Amendment 1 (1992) & Amendment 2 (1993) & Amendment 3 (1995) and Amendment 4 SS 143: 1998 with A1 & A2 or SS 143 : 2000 IEC 60065 :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 10Iron SS146:Part 2:1:1996 IEC 6033523 :1993 MOD Humidity test under tropical conditions 11Immersion water heater SS 146 Part 2: 14 : 1998 IEC 335274 :1994 12Kettle SS146:Part 2:2:1997 IEC 60335215 :1986 or IEC 60335215 :1995 13Laser disc set SS 143: 1988 with A1 & A2 or SS 143 : 2000 IEC 60065 :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065 :1998 46

Country Singapore 14Microwave Oven type or grouping Domestic Please tick box if SS 146: Part 2: 10 : 1994 with A1 or SS 146 Part 2:10:1998 Relevant International IEC 60335225 :1993 with Amendment 1 (1995) or IEC 60335225 :1996 Extent of Alignment State reason if MOD 15Mobile split air conditioner 16Mixer, blender, mincer and similar appliances SS 146 Part 2:16:1998 IEC 60335240 :1992 or IEC 60335240 :1995 SS 146 Part 2: 13:1998 IEC 60335214 :1984 with Amendment 1 (1989) & Amendment 2 (1990) or IEC 60335214 :1994 17Refrigerator SS 146 Part 2:17:1998 IEC 60335224 :1992 or IEC 60335224 :2000 18Rice cooker SS 146 Part 2:2: 1997 IEC 60335215 :1986 or IEC 60335215 :1995 19Room Air Conditioner SS 146 Part 2:16:1998 IEC 60335240 :1992 or IEC 60335240 :1995 MOD Water temperature for ice maker from 15 to 25 C 20 Television/video display unit 21Table or standing fan SS 143: 1988 with A1 & A2 or SS 143 : 2000 IEC 60065 :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 SS 146 Part 2:18:2000 IEC 60335280 (1997) MOD Subclause 21.101 Replace "A load equals to 4 times" by "..10 times" 47

Country Singapore type or grouping Domestic Please tick box if 22Table lamp/standing lamp SS 263: Part 6: 1989 or SS 263 Part 6:2000 Relevant International IEC 6059824 :1979 with Amendments 1,2 & 3 (1990) or IEC 6059824:1997 Extent of Alignment State reason if MOD 23Toaster, grill, roaster, hot plate and similar appliances SS 146 Part 2:15:1998 (applicable for toaster, grill, oven and similar appliances) IEC 6033529 :1993 (applicable for toaster, grill, oven and similar appliances), IEC 6033526 :1986 (applicable for hot plate and similar appliances) IEC 60335313 (1993) with Amendment 1 and/or Amendment 2 (applicable for deep fryer, electric wok and similar appliances) 24Video cassette recorder 25Vacuum cleaner 26Washing machine 27Wall fan/ceiling fan 283pin rectangular type 13Amp Plug SS 143: 1988 with A1 & A2 or SS 143 : 2000 IEC 60065 :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 SS146:Part 2:4:1996 IEC 6033522 :1993 SS146: Part 2:3:1995 IEC 6033527 :1993 MOD Water temperature for normal operation from 15 to 25 C SS 146 Part 2:18:2000 & SS 360: 1992 subclause 5.7 & 5.8 (applicable for ceiling fan) IEC 60335280 :1997 & [ SS 360 (1992) subclauses 5.7 & 5.8 applicable for Ceiling fan ] SS 145:Part 1:1997 based on BS 1363:Part 1:1995 MOD Subclause 21.101 Replace "A load equals to 4 times" by "..10 times" 48

Country Singapore 29Fuses ( 13A) for use in plug 303pin round type 15amp plug 31Multiway Adaptors type or grouping Domestic Please tick box if 323pin Portable Socketoutlet 33Portable Cable Reels 34Instantaneous Electric Water Heater 35Mains Pressure Electric Storage Water Heater Relevant International Extent of Alignment SS 167:1977 based on BS 1362:1973 SS 472: 1999 based on BS 546: 1950 SS 246:1996 based on BS 1363:Part 3:1995 SS 145: Part 2:1997 based on BS 1363 Part 2:1995 SS 307:1996 based on Draft IEC 1242 document reference 23B (Central Office) 192 SS 146:Part 2:5: 1999 SS 146:Part 2:8:1999 36 Residual Current Circuit Breaker (RCCB) SS 97: Part 1: 2000 373pin 13amp socketoutlet SS 145: Part 2: 1997 383pin round type 15amp socketoutlet SS 472: 1999 39 Domestic electric wall switch SS 227: Part 1: 2000 IEC 60335235:1997 IEC 60335221:1997 MOD MOD MOD based on BS 1363: Part 2: 1995 based on BS 546: 1950 IEC 606691: 1998 State reason if MOD a) Bare heating element not allowed b) Water temperature from 15 to 25 C c) Water heater shall be at least IPX4 a) Bare heating element not allowed b) Additional markings requirements c) To incorporate pressure relief valve, thermostat and thermo cutout Incorporated national wiring code requirement. 49

Country type or grouping Domestic Please tick box if 40 Ballast for tubular fluorescent lamp 41 Isolating transformer for downlight fitting SS 490: Part 2: 8: 2001 (magnetic ballast) or SS 490: Part 2: 3: 2002 (electronic ballast) Relevant International IEC 6134728: 2000 IEC 6134723: 2000 IEC 6155826: 1997 or IEC 6134722: 2000 (electronic isolating transformer) Extent of Alignment State reason if MOD 50

Country Thailand 15 type or grouping Ballast for fluorescent lamps PVC insulated aluminium cables Domestic Please tick box if mandat ory Relevant International TIS 232521 (1978) IEC 60920 (1990), Am.1(1993), Am.2(1995) IEC 60921(1988), Am.1(1990), Am.2(1994) Extent of Alignment State reason if MOD NEQ TIS 2932541 (1998) Electric irons TIS 3662528 (1985) IEC 6033523(1993), Am.1(1999), Am.2(1999) Starters TIS 1832528 (1985) IEC 60155(1993), for fluorescent Am.1(1995) lamps Incandescent lamps Lowvoltage distribution link fuses Lampholders for tubular fluorescent lamps and starterholders PVC insulated copper cables Fluorescent lamps : safety requirements TIS 4 Part 12529 (1986) IEC 60064 (1993) IEC 604321(1999) NEQ NEQ NEQ TIS 102529 (1986) IEC 602691(1998) NEQ TIS 3442530 (1987) IEC 60400 (1999) NEQ TIS 112531 (1988) IEC 602271 (1993), Am.1(1995), Am.2(1998) IEC 602272 (1997) NEQ TIS 9562533 (1990) IEC 60081:1997 NEQ 51

Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Thailand 15 AC electric fans : safety requirements TIS 9342533 (1990) IEC 603352 80:1997 NEQ Electric stoves; open type heating elements : safety requirements TIS 8702532 (1989) Mains operated electronic and related apparatus for household and similar general use : safety requirements TIS 11952536 (1993) IEC 60065:1985 MOD TIS 11952536 Subclause 9.1.1 the current measured shall not exceed 0.3 ma (peak) Lighting and similar equipment : radio disturbance limits TIS 19552542 (1999) CISPR 15:1999 52

Country type or grouping Thailand 15 Washing machines : safety requirements Domestic TIS 14632540 (1997) Please tick box if Relevant International Extent of Alignment State reason if MOD IEC 6033527:1993 MOD TIS 14632540 Subclause 2.2.9 water temperature 45+5C. Subclause 4.7 ambient temperature 27+2C. Subclause 29.1 requirements on creepage distance, clearance and distance through insulation. Annex B.5 ambient temperature 27+2C, humidity 65+5%. 53

Country type or grouping Thailand 15 Tumbler dryers : safety requirements Domestic TIS 13892539 (1996) Please tick box if Relevant International Extent of Alignment State reason if MOD IEC 60335211:1993 MOD TIS 13892539 Subclause 1.1 Scope excluding rated voltage 480 V. Subclause 4.3.1.4 temp. rise of the accessible front surface made of glass, ceramic and plastic pards. Subclause 4.14.6 minimum crosssectional area of conductors of supply cords Subclause 4.15.3 nominal crosssectional area of conductors. Subclause 4.18.2 requirements on creepage distance, clearance and distance through insulation. 54

Country Viet Nam 4 According to certification Scheme 14 According to import, export certification Scheme type or grouping Domestic Pleas e tick box if mand atory Relevant Extent International Alignment Electric Kettle TCVN5699215:2000 IEC335215:1995 and other and aments 1999 heating apparatuses with capacity not exceeding 10 litter Electric Fans TCVN 5699280:2000 IEC 603352 (includes desk 80:1997 fans, floor fans, wall fans) Electric Iron TCVN 569923:2000 IEC33523:1993 and aments 1:1999 Electric TCVN 5699223:2000 IEC 335223:1996 Hairdryers Fan: TCVN 56991:1998 IEC 3351:1991 (includes desk TCVN 5699280:1997 IEC 603352 fans, floor fans, 80:1997 wall fans, window fans, ceiling fans or roof fans, with electric motors, of a capacity not exceeding 125W ) Electric immersion sticks Storage Water Heaters Electric instantaneous water heaters Microwave Ovens Electric rice cookers Storage heating radiators TCVN 56991:1998 TCVN 5699215:2000 TCVN 56991:1998 TCVN 5699221:2001 TCVN 56991:1998 TCVN 5699235:2001 TCVN 56991:1998 TCVN 5699225:2001 TCVN 53931991 IEC 3351:1991 IEC 335215:1995 IEC 3351:1991 IEC 335221:1989 IEC 3351:1991 IEC 603352 35:1997 IEC 3351:1991 IEC 603352 25:2001 TCVN 56991:1998 IEC 3351:1991 IEC 335261 of State reason if MOD 55

Electrothermic hairdressing apparatus TCVN 5699:1998 TCVN 5699223:2000 IEC 3351:1991 IEC 335223:1996 Electric irons TCVN 56991:1998 TCVN 569923:2000 IEC 3351:1991 IEC 33523:1993 Electric TCVN 64801:1999 IEC 6691:1993 Switches Knife switches TCVN 64801:1999 IEC 6691:1993 and reverse knifes witches One phase TCVN 61881:1996 IEC 8841:1994 electric sockets and Plugs TCVN 6190:1999 IEC 8841:1994 Electric Wires coated with PVC or PE TCVN 66101:2000 TCVN 66102:2000 TCVN 66103:2000 TCVN 66104:2000 TCVN 66105:2000 TCVN 66106:2000 TCVN 6612:2000 TCVN 6612A:2000 TCVN 66131:2000 TCVN 66141:2000 TCVN 661412:2000 TCVN 661214:2000 TCVN 661431:2000 TCVN 661432:2000 IEC 2271:1993 IEC 602272:1997 IEC 2273:1993 IEC 2274:1992 IEC 602275:1997 IEC 2276:1985 IEC 228:1978 IEC 228A:1982 IEC 3321:1993 IEC 81111:1993 IEC 81112:1985 IEC 81114:1985 IEC 81131:1985 IEC 81132:1985 Electric motors and generators (excluding generating units) TCVN 66271:2000 TCVN 66272:2001 TCVN 66272A:2001 IEC 341:2000 IEC 342:1972 Amd 1:1995 IEC 342A:1974 TCVN 66273:2000 IEC 343:1988 TCVN 66278:2000 TCVN 66279:2000 IEC 348:1972 Amd 1:1990 IEC 349:1990 Amd 1 :1995 56

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES COUNTRY Brunei Darussalam TYPES OF CON FORMITY ASSESS MENT REGIMES Registration MODE OF REGULATION Suppliers registering products should register through the Procurement Section. Assessment Committee shall strictly review and analyse input information prior to endorsing approval of product registration based upon the mentioned requirements : Corporate information Quality and Performance (Quality Assurance details, test reports & certification carried out by International Test Bodies and representation of International used). Reliability and safety Maintenance management Track record Stock and delivery schedules After sale service Technical Presentation Cambodia ISC Mark Certification Treatment of Domestically Produced s: Application Assessment Type Test Assessment Awarding of Certificate Treatment for Import: I Registration / Type Approval for Imported s a Registration of Manufacturers 1 Application for registration attached with inspection data conducted by designated inspection bodies. 57

COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES 2 Issuing registration certificate MODE OF REGULATION Indonesia SNI Mark Certification b Type approval of products 1 application for type approval of products attached with testing reports conducted by designated testing laboratories ) 2 Issuing type approval certificate of the products 3 Manufacturers affix ISC mark on the products 4 Sale in Cambodian market 5 Surveillance II For the lot of Imported s (No Registration and Type Approval ) 1 Application for verification attached with testing reports conducted by designated testing laboratories 2 Issuing verification certificate 3 Affixing of ISC label 4 Sale in Cambodian market The Ministry of Industry and Trade through the Secretary General gazetted the procedure of SNI Mark product certification on June 1996 to ensure that the product meet the specified Indonesia National (SNI) requirements. There are two types of SNI i.e : Voluntary and Mandatory For the products, the producer/manufacturer has to fulfil two requirements i.e : 1. has to comply with the standard (SNI) 2. Mnufacturer has to implement one of the following modules which is based on Quality Management System i.e : Module I, BSN 10 Guidelines (16 elemenst/clause of ISO 9001) Module II, ISO 9003 Module III, ISO 9002 Module IV, ISO 9001 Module V, QMS which is equal to ISO 9001 58

COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION Producers/manufacturers who wish to seek SNI mark certification have to send an application to Centre for Standardization and Accreditation (PSA) Ministry of Industry and Trade. Then PSA proceeds for evaluation of the application and verification to the manufacturers premises. PSA issued SNI certificate if they comply with the requirements This regime is only applied for domestic electrical and electronic products since Indonesia does not have technical regulation for imported electrical and electronic products. Clause 19 article (2) in Government Regulation No. 102/2000 of National Standardization stipulates import products must fulfil SNI Lao PDR NIL Regulation is yet to be implemented. The procedures for certification of products where certification is voluntary is as follows: Malaysia Registration/certificati on Application Assessment Type test Assessment Awarding of certification A certificate of approval is required. To obtain approval, the following are needed: Test reports from local or foreign laboratories which are acceptable to ST. 59

COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION Submission of Form ST (PE) 3, test report and certificate. Enter the SIRIM Certification Scheme/SIRIM Batch Testing Scheme (every consignment is subjected to inspection and testing) Use of SIRIM s label Myanmar Treatment of Domestically Produced Equipment s have to be registered at the Electrical Inspection Department. Treatment of Imports British and Japanese standards are used. Philippines Registration/ Certification Philippine Standard (PS) Quality and/or Safety Certification Mark Scheme These marks are awarded to domestic and foreign manufacturers that consistently comply with quality management system standards. These are awarded after a thorough assessment of the manufacturer based on ISO 9000 series standards. The products are also subjected to laboratory testing to verify compliance with PNS. Even after the issuance of the license to use PS certification marks, surveillance is regularly conducted. Treatment of Imports s covered by certification shall secure Import Commodity Clearance with BPS. Import shipment that meets product quality and safety requirements of the specific Philippine National is issued the Import Commodity Clearance Certificate. 60

COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION Singapore Registration The regulatory regime consists of two phases premarket approval and postmarket surveillance. There is a regulator intervention prior to the entry of the regulated products into the market. The controlled goods have to go through a structured process of approval, which starts with testing and ends with labelling. Please see Section VI Flowchart of Singapore's Regime. After entry into the market, SPRING Singapore conducts regular visits to shops and retail outlets to ensure that only approved controlled goods are displayed or offered for sale. Treatment of Controlled Goods Registration of controlled goods is based on certification by designated Conformity Assessment Bodies. Thailand Certification Certification System of TISI consists of two phases: 1. License Granting Granting a license is based on: 1.1 The results of tests which are conducted on products in accordance with the application standards. Consideration on this matter may be: (1) Acceptation of testing results, or (2) testing by designated laboratories, or (3) testing by testing at manufacturer s premises, or (4) testing by supervised manufacturer s testing. 1.2 The results of manufacturer s quality control system assessment according to specified conditions. Consideration on this matter may be: (1) Acceptation of quality system certificates, or 61

COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION (2) Factory visit for quality control system assessment, or (3) Manufacturer s quality control system assessment on technical file of factory. Vietnam Registration/Certificat ion 2. Surveillance After granting a license, the licensee will be followed up by: 2.1 sampling from factories for testing, 2.2 sampling from market for testing, 2.3 sampling for testing each import, 2.4 Factory visit for audit. The procedures for certification of those products where certification is is as follows: Application Plan for assessment Assessment of conformity to standards Type Test/ Testing result + Surveillance (local product) Assessment Awarding of Certification Surveillance 62

COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES Registration/Import Export Goods Control The procedures for importexport goods control Application Type sampling Testing sample (s) Assessment Notification of control result MODE OF REGULATION 63

VI. FLOWCHART OF MEMBER COUNTRIES REGIME BRUNEI DARUSSALAM 64

CAMBODIA Ia Flowchart of Certification of Registration Foreign Manufacture, etc. Local Manufacture, etc. Request for Inspection Application for registration Application for Spot registration verification data registration and verification inspection Designated inspection bodies inspection data attached and document examination Department of Industrial of Cambodia Ministry of Industry, Mines and Energy Note:,, and are for accepting the testing data provided by designated inspection Bodies. and and are for other cases and for manufacturers in Cambodia 65

Ib Flowchart of Certification of Type Approval Foreign Manufacture, etc. Local Manufacture, etc. Request for Inspection Application for type Application for product Type verification data type approval approval type approval testing approval Specific foreign Testing institutes and inspection data attached Department of Industrial of Cambodia Ministry of Industry, Mines and Energy Foreign manufacturers, etc. Local manufacturers, etc. Affixing of standard mark by Manufacturers itself Imported product SALE Note:,, and are for accepting the testing data provided by designated testing laboratories., and are for other cases and for manufacturers in Cambodia 66

II Flowchart of Certification of Verification Foreign Manufacture, etc. Request for Inspection Application for Certification of verification data verification and verification inspection data Specific foreign attached Testing institutes Department of Industrial of Cambodia Ministry of Industry, Mines and Energy Affixing of standard mark by Department of Industrial of Cambodia SALE Note:,, and are for accepting the testing data provided by designated testing laboratories. 67

FLOWCHART OF INDONESIA S REGIME Diagrammatic Representation or flowchart of the regime Flow Chart of SNI Certification Process Incomplete 1 Applicant Administrative Disposition 2 Head of PSA Incomplete Incomplete 3 Head Of Accreditation Certification Process (Accreditation Division) Rej 4 Verification (Assessor) Module II, III, IV and V 51 5 2 Process 14 days 6 Head of PSA 7 Administration 9 8 Company 68

MALAYSIA To apply for the Certificate of Approval from ST Submission of Form ST(PE 3), test reports and certificate. The test reports and certificate are from local / foreign laboratories which are recognized by ST/DSM (Department of Standard Malaysia) After obtaining Certificate of Approval (COA) from ST, applicant needs to enter the SIRIM Certification Scheme/SIRIM Batch Testing Scheme (every Consignment Test at SIRIM is subject to inspection and testing) Use of SIRIM s label. 69

PHILIPPINES PS Quality and/or Safety Certification Mark Scheme No Supplier s application for PS Certification Mark License to CAB Review of application Factory assessment assessment and inplant testing Independent testing Evaluation of Factory and Assessment reports Passed Yes Issuance of PS Mark License 70

Import Commodity Clearance Scheme Start Submission of Application Application Review Exempted Issuance of Certificate of Exemption With Test Certificate A Retest Denial: Destruction or Exportation Conditional Release Passed Issuance of ICC A Draw Samples for Testing/Re Testing Evaluation of Test Report/ Certificate 71

SINGAPORE Supplier applies to SPRING Singapore to be a Registered Supplier Registered Supplier submits Controlled Goods to a CAB (Local) or CAB (ForeignMRA) for Certification to SPRING Singapore safety standards requirements CAB (Local) or CAB (ForeignMRA) issues COC (valid for 3 years) to Registered Supplier after certifying the Controlled Goods Registered Supplier submits COC to SPRING Singapore for registration of the certified Controlled Goods SPRING Singapore issues acknowledgement to Registered Supplier and lists the controlled goods in the Register Registered Supplier affixes SAFETY Mark and commences supply of registered controlled goods The SAFETY Mark comprises of a safety logo enclosed in a square on the left and the word SAFETY MARK enclosed in a rectangle on the right. Below the logo is an unique certification number traceable to the registrant. The colour used is Pantone 287C Blue Colour. Registered Supplier submits the registered controlled goods to the CAB for recertification before COC expires 72