Orbit rizonamist Installation Guide 53251-26 r
WELOME Thank you for choosing Orbit rizona mist. In the following pages you will find: Step-by-Step Installation Guidelines ssembly and Installation rawings and iagrams Personalized Parts List HEKLIST 1 r ecome Familiar with the Installation Guide 2 r Purchase dditional Materials 3 r Install Filter and Hose dapter 4 r Install ooster Pump (if selected) 5 r Install Mist Tubing and Nozzles 6 r Install uto-rain Valve and End Plug 7 r Turn Water Source On, Make djustments before you begin 1. ecome familiar with the installation guide We recommend that you read through the entire Installation Guide before you begin. Keep track of the items not provided and make a list of those things you will need to purchase separately. 2. Purchase dditional materials The parts list generated for your mist system outlines the parts needed to complete your installation. For periodic maintenance of your misting system, it is highly advised that you also purchase Misting Nozzle leaner. Removal of nozzles at the end of each summer season is recommended. Purchase Orbit/ rizona Mist Misting Nozzle Plugs to replace each nozzle during the rest of the year. Failure to follow these recommendations can result in hard water and debris buildup, creating a blockage in flow.
3. Install Filter and Hose dapter ttach your alcium Inhibitor Filter to your hose faucet by screwing the female end of the filter onto the faucet, until the connection is tight and secure. NOTE: If you are unable to attach your misting system directly to a faucet, you may attach the alcium Inhibitor Filter to a hose. ttach the female end of the hose adapter directly to the filter. To connect to your misting line, insert a length of 3/8" Mist Tubing into the open end of the adapter. Faucet alcium Inhibitor Filter (10109W) 3/8" Slip-Lok Hose dapter (92320W) 3/8" Mist Tubing (92228) 4. Install ooster Pump (if Selected) hoose a location to mount the booster pump between the water connection and the first nozzle in your system and within reach of a power outlet. Keyholes Use the keyhole slots in the back of the booster pump to mark proper screw placement on wall. Install screws or expanding anchors (in plaster or masonry, if necessary) into wall. Slip the booster pump over protruding screws. Plug in the power cord at the nearest power outlet. NOTE: Follow the installation instructions included with your booster pump. Wall
5. INSTLL Mist TUING and Nozzles 1 ssemble water feed line Measure and cut lengths of mist tubing appropriate to run a line from the 3/8" Slip-Lok Hose dapter to where you want your mist line to begin. NOTE: The mist line should be mounted 8' to 10' above the ground for optimal effect. To turn corners, insert the ends of the tubing into each end of a 3/8" Slip-Lok Elbow with a firm push motion. The tubing must be inserted past the O-ring inside the fitting to form a leakproof seal (approximately 3/4"). 2 ssemble mist line Use pre-cut 24" sections of tubing. Insert one end of the first section into a 3/8" Slip-Lok Elbow or 3/8" Slip-Lok Tee connecting the water feed line and the mist line. Insert the opposite end into a 3/8" Slip-Lok oupling with Nozzle. Note: fter each push of tubing in fitting, give a gentle pull on the tubing to assure proper insertion and engagement. Secure the tubing with 3/8" Mounting lamps. Place the clamp over the tubing, then pound the nail into the wall. Place clamps about 24" apart along the tubing line. ontinue this procedure until desired length of mist line is completed. Your line should now end with a 3/8" Slip-Lok oupling with Nozzle. Note: Mist line should not exceed 100' in length. F or E (If using a tee to go in multiple directions) G 3/8" Slip-Lok Hose dapter (92320W) 3/8" Mist Tubing (92228) 3/8" Slip-Lok Elbow (92110W) 3/8" Slip-Lok Tee (92120L) E 24" x 3/8" Flexible Mist Tubing sections (92225) F 3/8" Slip-Lok oupling with Nozzle (10121W) G 3/8" Mounting lamp (10114H)
5. INSTLL Mist TUING and Nozzles 1 IF USING OOSTER PUMP ssemble water feed line Measure and cut lengths of mist tubing appropriate to run a line from the 3/8" Slip- Lok Hose dapter to the booster pump and from the booster pump to where you want your mist line to begin. NOTE: The mist line should be mounted 8' to 10' above the ground for optimal effect. Insert the open end of 3/8" Mist Tubing coming from the 3/8" Slip-Lok Hose adapter into the port marked "IN" on the bottom of the booster Pump. Insert a new section of 3/8" Mist Tubing in the port marked "OUT" on the bottom of the booster pump. The rest of your water feed line will run directly off this tubing line. To turn corners, insert the ends of the tubing into each end of a 3/8" Slip-Lok Elbow with a firm "push and twist" motion. The tubing must be inserted past the O-ring inside the fitting to form a leakproof seal (approximately 3/4"). 2 ssemble mist line Use pre-cut 24" sections of tubing. Insert one end of the first section into a 3/8" Slip-Lok Elbow or 3/8" Slip-Lok Tee connecting the water feed line and the mist line. Insert the opposite end into a 3/8" Slip-Lok oupling with Nozzle. Note: fter each push of tubing in fitting, give a gentle pull on the tubing to assure proper insertion and engagement. Secure the tubing with 3/8" Mounting lamps. Place the clamp over the tubing, then pound the nail into the wall. Place clamps about 24" apart along the tubing line. ontinue this procedure until desired length of mist line is completed. Your line should now end with a 3/8" Slip- Lok oupling with Nozzle. Note: When using booster pump, mist line should not exceed 40' in length or use more than 20 nozzles. G or E F (If using a tee to go in multiple directions) H 3/8" Slip-Lok Hose dapter (92320W) 3/8" Mist Tubing (92228) ooster Pump (92100) 3/8" Slip-Lok Elbow (92110W) E 3/8" Slip-Lok Tee (92120L) F 24" x 3/8" Flexible Mist Tubing sections (92225) G 3/8" Slip-Lok oupling with Nozzle (10121W) H 3/8" Mounting lamp (10114H)
6. INSTLL uto-drain valve and end plug 3 t the lowest point in your line, install a 3/8" Slip-Lok oupling with Nozzle. onvert it into an auto-drain valve by removing (unscrew) the nozzle. In its place, screw the uto-rain Valve's male-threaded end into the coupling until the connection is tight and secure. 4 5 End your mist tubing line with a 3/8" Slip-Lok End Plug. Insert the 3/8" Slip-Lok End Plug with the tabbed end out into the last 3/8" Slip-Lok oupling with Nozzle on the mist line until the connection is tight and secure. If you have not already, secure the tubing with 3/8" Mounting lamps. Place the clamp over the tubing, then pound the nail into the wall. Place clamps about 24" apart along the tubing line. 3/8" Slip-Lok oupling with Nozzle (10121W) uto rain (10115) 3/8" Slip-Lok End Plug (92420W) 3/8" Mounting lamp (10114H) 7. TURN ON WTER SOURE/MKE JUSTMENTS Turn your water source on to check for any leaks in tubing or fittings. If any nozzles are not misting properly, check the nozzle's connection to the Slip-Lok fitting and tighten the connection accordingly. e sure to also check the end plug for any water leak. If there is a leak at the end plug, turn your water source off and tighten the end plug connection. Your misting system can be easily disassembled to correct problems, replace parts, or extend the system. To disassemble the tubing from the fitting, place a 3/8" open end wrench over the tubing next to the fitting. Pull the tubing away from the fitting while pressing the wrench against the fitting. This will depress the locking female part, releasing the tubing from the fitting.
PPENIX ooster Pump The booster pump increases regular mist line pressure capacity to 160 psi. This increase enhances the overall system s effectiveness to cool outdoor areas by creating a finer mist. The pump mounts easily to any wall and connects to your water source with built in Slip-Lok connections. Misting Nozzle leaner (8 oz.) The mist nozzle cleaner is specifically formulated to gently clean mist nozzles clogged with mineral deposits. It is easy to use, biodegradable and safe on brass, stainless steel and plastic. Misting Nozzle Plugs Nozzle plugs are used to replace nozzles in the off season when the mist is not used. They prevent insects from entering the mist line and clogging the system. They are also useful to plug off openings, when less mist is desired. Winterization While the uto-rain Valve is designed to drain excess water from your misting system, it is also recommended that you fully winterize your misting system. o this by disconnecting the hose adapter from the filer, then let gravity drain the leftover water from the mist tubing. Replace the mist nozzles with Misting Nozzle Plugs to protect your mist system as much as possible.