INSTRUCTION MANUAL Requires : -channel radio w/ micro servos, Outrunner Motor w/ Propeller Adaptor 0A Brushless ESC, 3 cells 11.1V 100mAh Li - Po battery & charger. Specifications Wing Span Wing Area Flying Weight Fuselage Length 36 in / 910 mm 0 sq in / 8. sq dm 7 oz / 770 g 38 in / 970 mm *Specifications are subject to change without notice.* Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. The World Models Manufacturing Co., LTD. www.theworldmodels.com FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY (ARF) SERIES MADE IN CHINA
INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS BEFORE YOU BEGIN P.1 P. P.3-P.10 P.10 1 3 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. Symbols used throughout this instruction manual comprise of the following :- Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Apply thread locker Must be purchased separately! Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Peel off shaded portion covering film. Cut off shaded portion. 3mm Drill holes with the specified diameter (here: 3mm). Pierce the shaded portion covering film. Pay close attention here! Warning! Do not overlook this symbol! P.1
Parts List 1. MAIN WING (Lower) -- 1 pc.. SERVO MOUNTING PANEL -- 1 pair SCREW PA1.7x8mm -- 8 pcs SCREW PBx1mm -- pcs FUEL TUBE dxdxmm -- pcs STRAPER -- pcs CLEVIS -- pcs HORN -- sets PUSHROD Ø1.x8mm w/ Threads (For Aileron) -- pcs 3. MAIN WING (Upper) -- 1 set. STABILIZER & ELEVATOR -- 1 set FUSELAGE -- 1 pc. SCREW PBx8mm -- pcs ELEVATOR LINK PL510010 -- 1 pc. BALSA x1x33.5mm -- 1 pc. 5. VERTICAL FIN & RUDDER -- 1 set 6. TAIL LANDING GEAR -- 1 set TAIL WHEEL Ø3mm -- 1 pc. PLASTIC COLLAR d1xd5xmm -- sets SCREW PAx8mm -- pcs SCREW PMx8mm -- 1 pc. M NUT -- 1 pc. ALUMINUM PLATE 0.3x8xmm -- 1 pc. 7. SCREW PBx10mm -- pcs CLEVIS -- 1 pc. FUEL TUBE dxdxmm -- 1 pc. HORN -- 1 set PUSHROD Ø1.x513mm w/ Threads (For Rudder) -- 1 pc. 8. FUEL TUBE dxdxmm -- 1 pc. CLEVIS -- 1 pc. PUSHROD Ø1.x73mm w/ Threads (For Elevator) -- 1 pc. 9. FOLDING PROPELLER SET PL63100 -- 1 set SCREW PWAx8mm -- pcs SCREW PM3x6mm -- pcs WASHER d3xd7mm -- pcs COWLING -- 1 pc. SPINNER Ø5mm -- 1 set 10. MAIN LANDING GEAR -- 1 pc. MAIN WHEEL Ø0mm -- pcs WHEEL PANTS -- 1 pair SCREW PMx6mm -- 3 pcs SCREW PM3x5mm -- pcs WASHER d3xd7mm -- pcs WASHER dx5mm -- 3 pcs M3 NUT -- pcs SCREW PWAx6mm -- pcs COLLAR Ø3.1mm w/ Set Screw -- sets COPPER TUBE d3.1xdxmm -- pcs ALUMINUM PLATE 0.5mm -- pcs 11. STRAPER -- pcs FUEL TUBE dxdxmm -- pcs SCREW PMx10mm -- 1 pc. WASHER dxd5mm -- 1 pc. M NYLON INSERT LOCK NUT -- 1 pc. BATTERY TIE -- 1 pc. SPONGE 10x50x150mm (For Radio Equipment) -- 1 pc. DOUBLE-SIDED TAPE 30x35mm -- 1 pc. MOUNTING PLATE 5x15mm PL11015 -- 1 pc. PLYWOOD x56x96mm -- 1 pc. 1. CANOPY -- 1 pc. SCREW PWAx8mm -- pcs PILOT (050A) -- 1 pc. 13. NYLON BOLT M.5x0mm -- pcs NYLON WASHER d.6xd9mm -- pcs PLASTIC PLATE 1x5.5x63.7mm (Wing Protection) -- 1 pc. 1. SCREW PWA.3x1mm -- pcs SCREW PMx1mm -- pcs SCREW PMX8mm -- pcs WASHER dxd5mm -- 1 pcs M NYLON INSERT LOCK NUT -- pcs PLYWOOD 3x53x170mm (Side Cabane) -- pcs FOAM 3x0x09mm (Wing Incidence Angle Template) -- pcs ALUMINUM PLATE (Brace: Fueslage to Wing) -- 1 set 15. SCREW PBx8mm -- 8 pcs HORN -- sets CLEVIS -- pcs FUEL TUBE dxdxmm -- pcs PUSHROD Ø1.x138mm w/ Threads (For Aileron to Aileron) -- pcs 16. DECALS: E51XMDEC -- 1 set COVERING:-- PURPLE COLOR SCHEME: LIGHTEX SGX100 WHITE LIGHTEX SGX01 BLACK LIGHTEX SGX31 BRIGHT RED LIGHTEX SGX370 SILVER LIGHTEX SGX561 PEARL PURPLE YELLOW COLOR SCHEME: LIGHTEX SGX100 WHITE LIGHTEX SGX01 BLACK LIGHTEX SGX31 BRIGHT RED LIGHTEX SGX370 SILVER LIGHTEX SGX330 CADMIUM YELLOW P.
1 Main Wing (Lower) Apply instant type CA glue to both sides of each hinge. Aileron Servo Lead Cabane Mount Aileron Servo (Lower) Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PBx1mm Screw PA1.7x8mm Screw 8 Straper Fuel Tube dxdxmm PA1.7x8mm TWM PL810010 CLEVIS WRENCH 0L 03L 0L 0R 03R 0R PBx1mm Fuel Tube dxdxmm Clevis Pushrod Ø1.x8mm mm Horn Please choose either 0L & 0R or 03L & 03R or 0L & 0R that suits your servo. P.3
3 Main Wing (Upper) Apply instant type CA glue to both sides of each hinge. Cabane Mount Cabane Mount Bottom View Stabilizer & Elevator PBx8mm Screw B (Stabilizer) B (Main Wing) B=B Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible. *Also refer to step 13 Wing Setting A A=A A mm PBx8mm Balsa x1x33.5mm Completed Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at side of control surfaces. Apply instant type CA glue to both sides of each hinge. 5 Vertical Fin & Rudder Apply instant type CA glue to both sides of each hinge. c c c=c' Completed P.
6 Tail Landing Gear PAx8mm Screw PMx8mm Screw M Nut 1 1 M Nut PMx8mm 1mm 1mm Plastic Collar PAx8mm 7 Rudder Pushrod PBx10mm Screw Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. Pushrod Ø1.x513mm Horn TWM PL810010 CLEVIS WRENCH mm Clevis Pushrod Ø1.x513mm 15mm 7mm PBx10mm Fuel Tube dxdxmm Bottom View 8 Elevator Pushrod TWM PL810010 CLEVIS WRENCH Clevis 57mm Pushrod Ø1.x73mm 130mm Fuel Tube dxdxmm Bottom View P.5
9 Outrunner Motor / Cowling PWAx8mm Screw PM3x6mm Screw d3xd7mm Washer PA.6x8mm Screw Outrunner Motor 8/ 30 KM083010 Propeller Adaptor (d3xd5) HW30100 Make sure rotating motor casing is not in contact with wirings or anything. Optional Parts 1 PMx1mm PM3x6mm d3xd7mm Washer Don't over-tighten the PM3 screws, too much stress on the screws could split the firewall. PMx1mm Don t over-tighten the PM screws, let the propeller blades align themselves when spinning. 3 Ø5mm Spinner M5 Nut PA.6x8mm TWM HW311100 PROPELLER ADAPTOR WRENCH 1.5mm PWAx8mm Completed 10 Main Landing Gear PMx6mm Screw 3 PM3x5mm Screw PWAx6mm Screw M3 Nut d3xd7mm Washer dxd5mm Washer 3.1mm Wheel Collar 3 d3.1xdxmm Copper Tube d.5xd8mm Washer PMx6mm PM3x5mm PWAx6mm d3xd7mm Washer Plate 0.5mm M3 Nut Wheel Ø0mm 3mm Set Screw Copper Tube d3.1xdxmm Wheel Pant 3.1mm Collar Bottom View 1mm Completed P.6
11 Radio Equipment PMx10mm Screw M Nylon Insert Lock Nut 1 1 dxd5mm Washer 1 Install and arrange the servo as shown in the diagram. Front Battery Battery Tie Sponge Rudder Servo Rudder Pushrod Fuel Tube dxdxmm Double-Sided Tape 0A Speed Controller Mounting Plate PMx10mm Bottom View Straper Elevator Pushrod Elevator Servo dxd5mm Washer mm PLYWOOD x56x96mm M Nylon Insert Lock Nut Bottom View 1 Canopy PWAx8mm Screw Pilot 1mm PWAx8mm P.7
13 Main Wing (Lower) M.5x0mm Nylon Bolt d.6xd9mm Nylon Washer Wing Protection 1x5.5x63.7mm M.5x0mm Nylon Bolt Bottom View d.6xd9mm Nylon Washer 1 Main Wing PWA.3x1mm Screw PMx8mm Screw PMx1mm Screw dxd5mm Washer 1 M Nylon Insert Lock Nut M Nylon Insert Lock Nut dxd5mm Washer PMx1mm 1.5mm PWA.3x1mm Pierce the two pre-drill holes at upper wing center cabane mounts and fasten the center cabanes with PMx1mm screw and nut. With the lower wing fastened to the fuselage, insert the wing incidence angle templates to both sides of upper and lower wing to hold the upper wing in position. Mark and drill 1.5mm pilot holes at the fuselage and fasten the center cabanes with PWA.3x1mm screws. WING INCIDENCE ANGLE TEMPLATE PLYWOOD 3x0x09mm SIDE CABANE PLYWOOD 3x53x170mm Side cabanes should fit to the outside of side cabane mounts. M Nylon Insert Lock Nut dxd5mm Washer mm PMx8mm With the wing incidence angle template still in place, position the side cabanes, mark and drill the side cabane mounts and fasten with PMx8mm screw and nut. P.8
15 Main Wing Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PBx8mm Screw 8 MainWing(Upper) Horn Clevis Pushrod Ø 1.x138mm PBx8mm Fuel Tube dxdxmm Clevis MainWing(Lower) Horn 16 Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A A' C B B' C' D D' E E' F G G' F' A=A' B=B' C=C' D=D' E=E' F=F' G=G' P.9
17 Control Throws Rudder 5mm 5mm Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Elevator 15mm 15mm Aileron 5mm 5mm 18 C.G. 89mm 3.5 in The ideal C.G. position is 89mm (3.5 in) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. C.G. Warning! Important Safety Precautions # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. # is specially designed to be powered by KM083010 Outrunner Motor. # Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. Extreme caution should be exercised when working with electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental movement of the throttle stick will spin the propeller and could cause injuries. # If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue and shrink the covering at the same time, causing the seams to pull away. # Check and re-tighten up all factory assembled screws, use thread locker if necessary. E51XMPO090906 P.10
LINKAGE CONNECTOR HW7111050 & HW7111060 Drill mm hole at servo horn. Insert linkage connector into servo horn. Shoulder Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Tighten up the round nut against the shoulder. Apply CA or permanent thread locker. After fastening the round nut, make sure that the linkage connector can rotate freely.
Product Registration Form (US Customers) We would like to share with you any relevant information regarding your model, including product news and free upgrade parts when applicable. Please fill in the following and send to AirBorne Models, 79-K, Bennett Drive, Livermore, CA 9551 USA. 1. Name:. Address: 3. Phone #: E-mail:. Model: Wing QC# Fuselage QC# (QC numbers are stamped on wing and fuselage) 5. Date of Purchase: 6. Store Name: Please call AirBorne Models at 95 371 09 for any assistance in filling this form. Thank you very much for purchasing our product.
Pl810010 Small Clevis Large Clevis
The World Models Manufacturing Co., LTD. www. theworldmodels. com E51XMPO090906