Processing vessels
Terlet Processing Vessels Terlet produces process tanks and vessels with a content ranging from 50 to 50,000 litres. These tanks and vessels are used for preparation processes during which products are mixed, stirred, cooled, heated or crystallized. Terlet top driven vessels MMR Vessels MMR tank for the preparation of soups, sauces and ragouts The MMR is a heating/mixing tank that is used for soup products requiring a combination of mixing and heating operations. An optimum mix has to be attained, in which the whole pieces, such as mushrooms, paprika, meat etc., are kept intact as much as possible. The soup must be cooked without causing it to burn and stick to the side. MMR processing tank for the processing of fruit products The MMR is a heating/mixing tank that is used for fruit products requiring a combination of processing operations. Firstly, an optimum mixture has to be obtained. Secondly, the fruit pulp must be heated without causing it to burn and stick to the side. Processing tank for the dairy industry The MMR is a processing tank that is employed as a mixing tank for mixing cream, fruit or herbs into curds and soft cheese. Features and benefits Optimum mixing action, even with thin soups containing vegetable and meat pieces No damage to the product solids Good heat transfer, resulting in fast heating Fermentation tank Culture and yogurt tank To allow milk to ferment in a tank in a low-spore environment and stir effectively the inoculation after it has reached the desired acidity degree. For culture preparation it is also necessary to cool the starter so far as possible (with chilled water) and checking the virulence of the culture. Features and benefits Result of scientific research Hygienic design CIP cleaning possible
Terlet bottom driven vessels Vessels with bottom driven agitators Cookers and coolers: Applications used for sauce-, soup-, ready meals and pie fill production. Features and benefits cooking vessel Full access Hygienic design Split dimple pressure jacket for cooking small batches Short heating times Wall and bottom surface scraped for optimal heat transfer Special agitator for intensive mixing action resulting in a more homogeneous end product Low maintenance Less product loss No dead corners No seals or bearings in contact with product Homogenizing through optional homogenizer in one vessel In tiltable execution for viscous products CIP provisions optional Features and benefits cooling vessel Hermetically closed No contamination in cooling phase Vacuum/pressure execution Cooling with central inner cylinder which means very short cooling times No fat separation No transport pump needed CIP provisions optional
Crystallization tank for the production of lactose To allow the lactose in concentrated whey to crystallize, with continuous supersaturation of the lactose contained in the solution during cooling. Pre-crystallization tank for whey powder To allow the lactose in concentrated whey to crystallize, at a constant temperature for the preparation of nonhygroscopic whey powder ( non-caking whey powder). Features and benefits Optimum mixing action No damage to crystals Even cooling Maximum cooling surface resulting in large, regular crystals Hygienic design
Terlet horizontal vessels Horizontal vessels for the production of soups, sauces and fruit Features and benefits Optimum mixing action, even at minimum fill ratio Large heat exchanging surface No damage to the product because of the low revolving speed of the stirring mechanism Horizontal tanks for the processing of soups and sauces The horizontal cooking/mixing tanks are primarily employed in the preparation of sauces and soups in which there is a large variation in relative density. In other words, the tendency for the components to sink or float. Horizontal tanks for the processing of fruit products A horizontal tank can be used for the preparation of all kinds of fruit products. A great advantage is the very efficient mixing of products that tend to sink to the bottom or, conversely, float to the top.
Bottom driven vessel 50-1.500 L MMR Processing tank 800-5.000 L Horizontal tank 500-5.000 L Bottom driven tank 1.000-40.000 L Top driven tank 800-40.000 L Terlet BV Oostzeestraat 6 7202 CM Zutphen The Netherlands Terlet USA 1385 Armour Blvd. Mundelein, IL 60060 USA Telephone Fax E-mail Internet +31 575 593 100 +31 575 593 111 info@terlet.com www.terlet.com Telephone Fax E-mail Internet +1 847 247 0182 +1 847 247 0184 info@terlet.com www.terlet.com
Terlotherm Scraped surface heat exchanger
Why a Terlotherm scraped surface heat exchanger? Many prepared foods and other products prevent optimal heat transfer because of their consistency. For example, food containing large particles, viscous, sticky and crystalline products can quickly block or foul certain types of heat exchangers. Scraped surface heat exchangers incorporate special design features which make them ideal for heating and cooling products that impair good heat transfer. As the product is pumped through the SSHE cylinder, even temperature distribution is ensured by a rotor and blade assembly, which continually and gently blends the product, while simultaneously removing it from the heat transfer surface. The Terlotherm is a vertical scraped surface heat exchanger with two concentric heat exchange surfaces to provide optimum heat transfer. This design, together with other features, offers the following advantages:: Vertical unit, which gives a large heat exchange surface area, and gives a small foot print so valuable production floor space area, is not required. Our largest machine gives more than eight times the surface area than conventional equipment. One mechanical seal. All other types of equipment have a minimum of two seals, and require a lot of time to replace the seals. The seal in the Terlotherm can be changed very quickly. No special hydraulic system is required either as in other conventional equipment. Simple inspection of the interior of the machine via the top lid, which can be opened without tools. There is no need to disturb seals or remove shafts. For maintenance purposes the equipment is easily accessible and simple to clean. All product contacting parts are of FDA approved material. The machine is designed in such a way that the heat exchange surfaces can easily be separated in case either surface needs to be refinished or replaced. The heat exchange surfaces are not provided with potentially dangerous materials such as chromium or other materials, but are of solid high quality stainless steel, thus avoiding the danger or contamination of the product. The Terlotherm operates utilizing low pressures and low rpm s, but still maintains the same tip speeds of the scraper blades as other units that run at much higher rpm s and pressures. This is due to our unique design of the double wall cylinder. This is a key advantage when you have very sensitive or complex products that can be easily damaged with too much pressure or too high rpm s. Due to the modular building design the heat exchange capacity can be increased by replacing the cylinders instead of the complete machine. Efficient heat transfer is achieved by continuous scraping or the entire heat exchange surface. The Terlotherm has been approved with USDA, U-Stamp and ASME codes.
Products and processes Typical products processed by the Terlotherm: Sauces & condiments: Confectionary: Dairy: Meat products: Mayonnaise Caramel Pudding Taco filling Ketchup Chocolate WPC MDM Starch paste Compounds MPC Pet food BBQ sauce Wafer cream Yoghurt Mustard Fondant Quark Personal care: Alfredo sauce Jelly Dairy creamer Ointments Cranberry sauce Fudge Ice cream mix Lotions Marinara sauce Marshmallow Cream cheese Gels Gravies Waffle batter Vaseline Cheese sauce Icing Fruit: Waxes Tartar sauce Syrup Aseptic fruit Salad dressing Crème patisserie Fruit preps General: Chili Marmalade Peanut butter Hummus Chutney Potato mash Salsa Apple sauce Egg Tapenade Pie filling Olive paste Smoothie Continuous HTST pasteurization heating and cooling line Wax, emulsion cooling crystallization line
The Terlotherm can handle particles up to 1 inch. 1 inch Terlotherm advantages and applications Advantages Scrapers can easily be replaced without tools Can be CIP cleaned and SIP sterilized Product area inspection without removing seal Lid can be opened with quick clamp system Large heat exchange area with small footprint Tangential inlet Acceleration and deceleration area No damage to product Maintenance-friendly; only one seal and one drive Exchangeable cylinders Applications Heating Aseptic cooling Deep-cooling Crystallization Tempering Sterilization Pasteurization Polymerization Gelling
Terlotherm Laboratorium skid R&D purposes Small batch sizes 50-100 L per/hour Inline heating and cooling Optional modular product holding section for variable time temperature combination Data login system for storing all necessary test parameters The scraper The scraper blades are manufactured of a high quality X-ray and metal detectable synthetic material, which is tasteless, non-toxic and contains no undesirable reinforcing material such as glass fibers, etc. The chemical resistance is very high, were as the water absorption is extremely low. Bacteriologically this synthetic material is inert.
Terlotherm model Heat exchange surface area m2 Annular product space mm Total height mm Footprint m2 Number of scrapers Scraper peripheral velocity m/s Product inlet NW Product outlet NW Medium inlet inner cylinder inch Medium inlet outer cylinder inch Medium outlet inner cylinder inch Medium outlet outer cylinder inch Maximum pressure product area barg Maximum pressure medium area barg Cooling medium flow rate m3/hr Lab 0.3 50 855 0.5 16 0,5-3,0 25 25 1/2 1/2 1/2 1/2 5 4 2 50 0.5 50 1345 1.0 8 0,5-3,0 65 65 1 1.5 1 1.5 10 6 8 100 1.0 50 1675 1.0 16 0,5-3,0 65 65 1 1.5 1 1.5 10 6 8 150 1.5 50 1985 1.0 24 0,5-3,0 65 65 1 1.5 1 1.5 10 6 15 200 2.0 50 2305 1.0 32 0,5-3,0 65 65 1 1.5 1 1.5 10 6 15 450 4.5 50 2475 1.4 48 0,5-3,0 80 80 1.5 2 1.5 2 10 6 25 700 7.0 50 3115 1.4 72 0,5-3,0 80 80 2 3 2 3 10 6 45 Delta 50 Delta 100 Delta 150 Delta 200 Delta 450 Delta 700 3115 2305 2475 1985 1665 1345 Terlet BV Oostzeestraat 6 7202 CM Zutphen The Netherlands Terlet USA 1385 Armour Blvd. Mundelein, IL 60060 USA Telephone Fax E-mail Internet +31 575 593 100 +31 575 593 111 info@terlet.com www.terlet.com Telephone Fax E-mail Internet +1 847 247 0182 +1 847 247 0184 info@terlet.com www.terlet.com
Van Meurs Bag-in-Box aseptic filling machines
Sterile means sterile and germ free means germ free Thanks to the unique dry sterilisation filling process of the Van Meurs aseptic fillers. The unique dry-sterilization filling process of the Van Meurs Bag-in-Box filling machines ensures that, sterile remains sterile, low-germ count remains low-germ count. Thanks to the unique filling valve, it is possible to vacuumize the bag before filling, fill the bag with product and inject steam or an inert gas before closing the bag. Combined with an advanced PLC control that controls all pressures, temperatures, airflow, etc., the Van Meurs bagin-box filling machines will not cause re-infection The excellent mechanical design of the Van Meurs Bag-in-Box filling machines, supported by a very accurate PLC control system, eliminates the need for chemicals, and requires the very minimum use of steam. Due to the controlled filling process, the shelf life of even the most sensitive liquid foodstuffs can be extended to a considerable extent. Advantages Long life, thus lower spoilage losses Very low operational costs and simple operation Flexibility in use of different types of packing The possibility of working with all conventional bag-inbox brands and closure systems Very accurate dosing system, which prevents spillage of your precious product Built-in automatic control functions, which monitors the filling process Comprehensive and convenient service, with troubleshooting over modems
Main features A special filling valve which will be cleaned and sterilized during production (Cleaned In Process). Steam sterilization and, subsequently, drying of the filling valve with sterile air, after each filled bag. The filling valve is fully clean and dry when it comes into contact with the spout of the next bag. Vacuum purging of the bag before filling and after each filling to prevent product from dripping. Steam or inert gas injection in the bag as well as the bag closure once it has been filled. An extra aseptic dosing valve to ensure accurate filling and avoid water hammering. An absolutely dry filling chamber which is foreseen with a laminar flow of sterile air. The machines are foreseen with a sterile filter system and vacuum installation. Provided with the option to handle bag closures with and without pre-closing position A quickly interchangeable gripper with the possibility of handling all conventional bag-in-box brands and closure systems. Filling bag-in-box semi automatic or fully automatic Filling small as well as big volumes. (2-1000 liter) Filling in the box, separate from the box or in a drum, pallecon, octabin PLC control by means of Siemens S7 PLC and display Communication module with modem Repeatability accuracy between ±0,5% (depending on bag size and product) Market and applications: Tea concentrates Dairy products (icemix, cream, milk, condensed milk) Fruit products (juices, purees, jams and concentrates) Liquid egg products (whole egg, egg white and eggyolk) Post mix and syrups Water Soy Available options Sauces ( mayonnaise, ketchup) Bakery products Optionally can the Van Meurs be equipped with a roller conveyor underneath the filling chamber (Type B200A). Also will it be possible to extend the Van Meurs with an extra roller conveyor and funnel to guide the filled bag gentle in a box (Type B200B). The Van Meurs can be foreseen with several options of which the most important are: Mass flowmeter instead of inductive high-speed metering tube A steam generator instead of steam accumulator Sterilisation/CIP manifold controlled by the PLC which takes care of the sterilisation, CIP and draining (including temperature measurement) Filling valve for very viscous products as well as for products that contain whole parts. Aseptic tanks with sterile air pressure and/or level control
Model overview B100 The B100 is a single head, non-aseptic, semiautomatic Bag-in-Box filling machine. The B100 is foreseen with a small in height adjustable roller conveyor which easy can be removed without the use of tools. The B100 is suitable for filling all Bag-in-Box packaging s: Small as well as large volumes (2 up to about 1000 litres) and suitable for filling bags in the box or separate from the box. B200C The B200C is a single head, aseptic, semiautomatic Bag-in-Box filling machine. The B200C is foreseen with a widened frame and a small in height adjustable roller conveyor which easy can be removed without the use of tools. The B200C is suitable for filling all Bag-in-Box packaging s: Small as well as large volumes (2 up to about 1000 litres) and suitable for filling bags in the box or separate from the box. B200 BID The B200 Bag-in-Drum (BID) filler is a single head, aseptic, semiautomatic Bag-in- Drum filling machine. The B200BID is equipped with a frame which is adapted to the height of the roller conveyor on which the drums will be transported. Smaller volumes can still be filled by means of the standard small roller conveyor The B200 Bag-in Drum is suitable for filling Bag-in-Drum. (Approx. 200kg) B400 The B400 is a single head, aseptic, fully automatic Bag-in-Box filling machine.the empty bags will be automatically inserted in the filling chamber. Filled off bags will be transported to the backside of the machine. The bags will be separated by means of a cutting device after which the bags will be transported to a funnel unit. The funnel is mounted in a fixed position on the frame. The funnel unit will guide the bag in the box.the B400 is suitable for filling bags with content of 2 up to about 25 on a web.
Technical specification: Product : Intermittent with a optimum capacity of 5.500-9.000 liters per hour. Pressure air : About 11 Nm3 per hour, 6 bar(g), oil free, dew point 4 C. Electricity : 400 volt, 50 Hz, 3ph, zero, earth, +10 % - 15%. Steam : 3 bar (g) Foodgrade. Water : 0,2 Nm3 per hour Modem : Analog telephone line (direct line) Capacity : Typical capacity at a flow rate of 2.5 L/sec, will be approximately 260 bags per hour. (depending on product specification) Materials and finish: Cladding and machine frame are made of stainless steel 1.4301/A304, the finish is fixed K220 Machine parts that come into contact with the product are made of stainless steel 1.4404/ A316L. Other machine parts are made of sophisticated technical synthetics.
outstanding reputation and an impressive reference list. Terlet has an experienced team of professional specialists who know their customer s products and applications. Our Thanks to our many years of experience and knowledge of a broad range of markets, we are able to develop the best solution to your needs, but also to provide valuable advice to optimize your production process. Terlet BV Oostzeestraat 6 7202 CM Zutphen The Netherlands Telephone Fax E-mail Internet +31 575 593 100 +31 575 593 111 info@terlet.com www.terlet.com Terlet USA 1385 Armour Blvd. Mundelein, IL 60060 USA Telephone Fax E-mail Internet +1 847 247 0182 +1 847 247 0184 info@terlet.com www.terlet.com