ORE TOTAL FLOOD PROTETION AL DETAIL IAN: 1. WIRE MAIN ONTROL PANEL PER INLUDED SHEMATI 2. WIRE ALL FANS PER INLUDED SHEMATI 3. WIRE SHUNT TRIP BREAKER (OPTIONAL) 4. WIRE UDS APPLIANE KILL, IF EQUIPPED (OPTIONAL) 5. WIRE VALVE 05/08/2013 Rev. 8 AL ONTRATOR REQUIREMENT ITEM ONNETION IN PANEL ONNETION IN DEVIE VOLTAGE AMPERAGE OMMENTS SHUNT TRIP BREAKER (OPTIONAL) ST & N1 BREAKER OIL (A1 & A2) 120 VA < 4 AMPS ST TO A1 ON SHUNT BREAKER OIL, AND NEUTRAL TO A2 ON SHUNT TRIP BREAKER OIL ONTROL PANEL POWER H1 & N1 + GROUND IRUIT BREAKER 120 VA 15 AMPS ONTROL PANEL POWER MUST NOT BE RUN THROUGH SHUNT TRIP BREAKER UDS APPLIANE KILL (OPTIONAL) KTS & N1 KTS & N1 120 VA < 4 AMPS KILL TERMINALS MUST BE IN SERIES WITH OTHER KILL ES REMOTE ANSUL AUTOMAN (OPTIONAL) AU1, AU2 SOLENOID 120 VA < 6 AMPS 120V TO AU1, AU2 TO ANSUL AUTOMAN, ANSUL SOLENOID TO NEUTRAL VALVE 35 & N1D (IF 24 VD) & N1 (IF 120 VA) RED/RED/GREEN 24 VD OR 120 VA < 1.0 AMPS IF 24 VD - 2 WIRES & GROUND, N1D TO RED, 35 TO RED, AND GREEN TO GROUND IF 120 VA - 2 WIRES & GROUND TO RED, N1 TO RED, AND GREEN TO GROUND SHUNT TRIP BREAKER (OPTIONAL) -2 WIRES, 120VA -ST TO A1 ON SHUNT BREAKER -NEUTRAL TO A2 ON SHUNT TRIP BREAKER ONTROL PANEL POWER -2 WIRES & GROUND -120 VA, 15 AMP SERVIE -WIRE TO H1 AND N1, GROUND -POWER MUST NOT ORIGINATE FROM SHUNT TRIP BREAKER 36 INHES LEARANE REQUIRED IN FRONT OF ALL UTILITY ABINET DOORS VALVE POWER -2 WIRES & GROUND -24 VD WIRE TO 35 & N1D -120 VA WIRE TO & N1 POWER TO APPLIANE VALVE
ORE TOTAL FLOOD PROTETION LOW-VOLTAGE DETAIL ALARM ONTRATOR: 1. WIRE REMOTE PULL STATIONS, REMOTE STATS, ORE INTERLOKS, SENSORS AND ALARM ONTATS 2. OMPLETE FINAL HOOKUP OF SYSTEM 3. PERFORM FINAL SYSTEM TEST 4. FILL SURFATANT TANK 05/08/2013 Rev. 8 ALARM ONTRATOR REQUIREMENT ITEM ONNETION IN PANEL ONNETION ON DEVIE VOLTAGE AMPERAGE OMMENTS REMOTE PULL STATION(S) 22 AND 25 21 AND 26 1 & 2 24 VD < 1.0 AMPS PULL STATION OVER N/A N/A N/A N/A REMOTE STAT SENSOR(S) 25 AND 23 26 AND 24 BLAK AND WHITE 24 VD < 1.0 AMPS ALARM ONTAT AL1, AL2 VARIES MAX 50 VA UP TO 1 AMP ORE INTERLOK(S) ILA, ILB, IL ILA, ILB, IL RS-485 OMMUNIATIONS SIGNAL WIRE PULL STATION TERMINAL 1 BETWEEN HOOD ORE PANEL TERMINALS 22 AND 25 WIRE PULL STATION TERMINAL 2 BETWEEN HOOD ORE PANEL TERMINALS 21 AND 26; USE BELDEN #6320UL OR SIMILAR WIRE PULL STATION OVER MUST BE INSTALLED IF SURFAE MOUNTED, USE OVER EXTENSION STI-6531B WIRE SENSOR BLAK WIRES BETWEEN HOOD ORE PANEL TERMINALS 25 AND 23 WIRE SENSOR WHITE WIRE BETWEEN HOOD ORE PANEL TERMINALS 26 AND 24 HIGH TEMP (842 F) #W04427 (WHT) & #W04427B (BLK)WIRE OR SIMILAR ONLY IF RAN OVER TOP OF HOOD; OTHERWISE BELDEN #6320UL OR SIMILAR PLENUM RATED WIRE; SEE FIGURE 1 ALARM RELAY ONTATS FOR BUILDING ALARM LOATED IN THE ORE AL ONTROL PANEL ORE SYSTEM (1) ILA, TO ORE SYSTEM (2) ILA. ORE SYSTEM (1) ILB, TO ORE SYSTEM (2) ILB. ORE SYSTEM (1) IL, TO ORE SYSTEM (2) IL. USE BELDEN# 88760 OR SIMILAR WIRE TROUBLE ONTAT TB, TBL, TOK VARIES MAX 120 VA UP TO 6 AMPS WIRE TO TBL & TB NORMALLY OPEN ONTAT, LOSES IN TROUBLE ONDITION ORE OMMUNIATIONS ABLE RJ-45 Jack INTERNET ONNETION SIGNAL <1.0 AMPS TYPIAL ONNETION AT5 ABLE TO LOAL AREA NETWORK VIA ETHERNET OR WIRELESS ROUTER WITH VALID INTERNET ONNETION ALARM ONTAT -2 WIRES WIRED TO NORMALLY OPEN ONTATS (LOSES IN ONDITION) -ORE ONTROL PANEL AL1 AND AL2 -SEE FIGURE 2 ALARM PANEL ORE INTERLOK -2 WIRES + SHIELD -USE BELDEN#88760 OR SIMILAR WIRE -SEE FIGURE 3 TROUBLE ONTAT -2 WIRES TO NORMALLY OPEN ONTATS (LOSE IN TROUBLE ONDITION) -ORE PANEL TERMINALS TBL AND TB -SEE FIGURE 4 SUPERVISED LOOP -4 WIRES, 24VD ONNET BLAK WIRES BETWEEN 25 AND 23 IN PANEL, ONNET WHITE (OR RED) WIRES BETWEEN 26 AND 24 IN PANEL -ADDITIONAL STATS, WIRED IN SUPERVISED LOOP -USE HIGH TEMP (842 F) #W04427 (WHT) & #W04227B (BLK)WIRE ONLY IF RAN OVER TOP OF HOOD; OTHERWISE BELDEN #6320UL OR SIMILAR PLENUM RATED WIRE -SEE FIGURE 1 36 INHES LEARANE REQUIRED IN FRONT OF ALL UTILITY ABINET DOORS PULL STATION 10 TO 20 FEET FROM HOOD LOATED NEAR POINT OF EGRESS FROM HOOD ORE OMMUNIATIONS ABLE -AT5 ABLE MUST BE INSTALLED TO A LOAL AREA NETWORK WITH VALID INTERNET AESS VIA ETHERNET OR WIRELESS ROUTER PULL STATION WIRES -4 WIRES, 24VD WIRE (TERMINAL 1) BETWEEN 22 AND 25 -WIRE (TERMINAL 2) BETWEEN 21 AND 26 -ADDITIONAL PULL STATIONS WIRED IN SUPERVISED LOOP -USE BELDEN #6320UL OR SIMILAR WIRE -SEE FIGURE 1 42 TO 48 INHES ABOVE FLOOR LEVEL TO ENTER OF HANDLE PULL STATION PART #STI-SS2431 PROTETIVE OVER MUST BE INSTALLED
ORE TOTAL FLOOD PROTETION LOW-VOLTAGE FIGURES 05/08/2013 Rev. 8 J2-1 J2-2 21 22 PULL STATION 1 2 STAT-1 25 26 BREAK WIRE BEFORE INSERTING INTO TERMINALS BUILDING ALARM ORE ONTROL PANEL ALARM ONTAT SHIELDED TWISTED PAIR J2-3 23 STAT-2 ALARM INPUT AL1 AL2 END OF LINE DEVIE ILA ILB BK RD BK RD ILA ILB J2-4 24 IL IL WIRING ONNETIONS FOR SUPERVISED LOOP FIGURE 1 WIRING ONNETIONS FOR ALARM ONTAT FIGURE 2 WIRING ONNETIONS FOR ORE INTERLOK FIGURE 3 BUILDING ALARM ORE ONTROL PANEL TROUBLE ONTAT PRV WATERLINE TROUBLE INPUT TOK TB TBL NO N 1 2 END OF LINE DEVIE WIRING ONNETIONS FOR TROUBLE ONTAT FIGURE 4
ORE TOTAL FLOOD PROTETION PLUMBING DETAIL PLUMBER: 1. ONNET HOT WATER LINE; PV, OPPER OR STAINLESS STEEL PIPE ONLY 2. ONNET HOOD DRAIN(S) STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY 3. ONNET ALL END-TO-END AND BAK-TO-BAK HOOD WATER LINE ONNETIONS (PLUMBING IS FIELD SUPPLIED FOR THIS) FIELD PLUMBING MUST NOT EXEED HEIGHT OF VAUUM BREAKER IN MAIN UTILITY ABINET REMOVE PLUG FROM MAIN HOOD SPRAY BAR AND ONNET TO NEXT HOOD STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY 4. PLUMB VALVE 5. INSTALL FLOOR DRAIN 6. INSTALL BAKFLOW PREVENTER IF ODE REQUIRES PLUMBING ONTRATOR REQUIREMENT ITEM ONNETION TEMPERATURE PRESSURE FLOW RATE OMMENTS HOT WATER LINE 3/4 INH NPT 140 to 170 F 30 TO 70 PSI 0.7 GPM PER FOOT OF HOOD INSULATE HOT WATER PIPE, MINIMUM PRESSURE DEPENDANT ON LENGTH OF HOOD SYSTEM GRAVITY 0.7 GPM PER FOOT OF 2 DRAINS ON 24 INH TALL HOODS WITH 20 INH TALL FILTERS AND HOODS 10 FEET AND HOOD DRAIN(S) 1-1/2 INH NPT N/A DRAIN HOOD LONGER END-TO-END ORE ONNETION 3/4 INH NPT N/A N/A N/A ONNET WITH NPT PIPE, SEAL ALL THREADS, HOOD ONNETION PROVIDED, FIELD PIPING MUST REMAIN BELOW HEIGHT OF VAUUM BREAKER BAK-TO-BAK ORE ONNETION 3/4 INH NPT N/A N/A N/A ONNET WITH NPT PIPE, SEAL ALL THREADS, HOOD ONNETION PROVIDED VALVE VARIES N/A SEE HART N/A UP TO 2 INHES NPT WITH 24V ONTROLS, 2-1/2 AND 3 INH USE 120V ONTROL FLOOR DRAIN(S) 1-1/2 INH N/A GRAVITY DRAIN N/A USED TO HELP LEAN UP SYSTEM DISHARGE, GREASE INTEREPTOR MAY BE REQUIRED BAKFLOW PREVENTER DRAIN LINE (OPTIONAL) INLET/OUTLET DRAIN HOT WATER LINE -PV, OPPER, OR STAINLESS STEEL PIPE ONLY -140-170 F OPERATING TEMPERATURE -30 TO 70 PSI OPERATING PRESSURE -125 PSI MAX STATI PRESSURE -0.7 GPM PER FOOT OF HOOD -3/4 INH NPT FITTING, INSULATED N/A VARIES N/A 05/08/2013 Rev. 8 INSTALLED WHEN PAKAGE HAS A BAKFLOW PREVENTER VALVE, SEE BAKFLOW PREVENTER VALVE MANUAL FOR DETAILS PRESSURE REGULATOR VALVE REGULATORS ARE NOT INLUDED TO MEET REQUIRED PRESSURE AND MUST BE ORDERED SEPARATELY PART NUMBERS: X65BU(3/4"), X65BU(1"), OR X65BU(1-1/2") ONSULT FATORY FOR SIZING END-TO-END OR BAK-TO-BAK ONNETION -INSTALLED AND PROVIDED BY PLUMBER STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY -FIELD PIPING MUST REMAIN BELOW HEIGHT OF VAUUM BREAKER HOOD DRAIN(S) -1-1/2 INH NPT ONNETED TO BUILDING GREASE TRAP -2 DRAINS ON 24 INH TALL HOODS WITH 20 INH FILTERS -2 DRAINS ON HOODS 10 FEET AND LONGER -STAINLESS STEEL, OPPER OR STEEL PIPE ONLY 36 INHES LEARANE REQUIRED IN FRONT OF ALL UTILITY ABINET DOORS VALVE -THREADED NPT ONNETION -SEE TABLE BELOW MAX PRESSURE FLOOR DRAIN -1-1/2 DRAIN INSTALLED IN FLOOR, NEAR APPLIANES -FLOOR DRAINS MAY BE USED TO DRAIN HOOD -GREASE INTEREPTOR MAY BE REQUIRED SIZE MAX INLET PRESSURE VOLTAGE BTU/HR 3/4" 25 24VD 247,500 1" 25 24VD 1,119,000 1-1/4" 25 24VD 1,730,000 1-1/2" 25 24VD 1,900,000 2" 15 24VD 3,251,000 2-1/2" 5 120VA 5,821,000 3" 5 120VA 7,430,000
ORE TOTAL FLOOD PROTETION SPRINKLER DETAIL 05/08/2013 Rev. 8 BUILDING SPRINKLER ONTRATOR: 1. ONNET ORE WATER LINE TO BUILDING WET SPRINKLER SYSTEM. STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY SPRINKLER ONTRATOR REQUIREMENT ITEM ONNETION OPERATING PRESSURE K-FATOR FLOW RATE OMMENTS ORE WATER SUPPLY LINE 3/4 INH NPT 30 PSI TO 70 PSI SEE TABLE PRESSURE REGULATOR VALVE (PRV) -PRV NOT INLUDED AND MUST BE PROVIDED, INSTALLED, AND ADJUSTED BY THE SPRINKLER ONTRATOR TO MEET INOMING PRESSURE REQUIREMENTS -A REGULATOR SUH AS THE ELKHART BRASS MODEL NUMBER URFA-20S-2.5" OR THE UR-20 SERIES PARTS KITS SHOULD BE UTILIZED -MUST BE ONFIRMED WITH THE MARSHAL OR LOAL AUTHORITY HAVING JURISDITION (AHJ) ORE WATER SUPPLY LINE -30 PSI TO 70 PSI OPERATING PRESSURE -125 PSI MAX STATI PRESSURE, 3/4 INH NPT FITTING, 1.5 GPM PER FOOT OF HOOD -ONNETED TO SUPERVISED, DEDIATED LINE WITH NO UNSPUERVISED MANUAL SHUT-OFF VALVES -ONNET TO BUILDING SPRINKLER WATER LINE (REDUE PRESSURE) WHEN REQUIRED -STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY 1.5 GPM PER FOOT OF HOOD WATER LINE MUST BE SUPERVISED AND HAVE NO UNSUPERVISED MANUAL SHUT-OFF VALVES MINIMUM PRESSURE AND FLOWRATE DEPENDENT ON LENGTH OF HOOD SYSTEM LENGHT OF HOOD (FT) MINIMUM OPERATING PRESSURE REQUIREMENTS MINIMUM INLET WATER PRESSURE FOR SELF LEANING (PSI) MINIMUM INLET WATER PRESSURE FOR ORE PROTETION (PSI) DISHARGE OEFFIIENTS (K-FATOR) 4 30 30 1.3 8 30 30 2.6 12 30 30 4.0 16 30 30 5.3 20 31 33 6.4 24 32 36 7.4 28 34 39 8.3 32 37 44 9.0 36 39 49 9.7 40 42 56 10.2 44 46 63 10.6 48 50 70 11.1 TOTAL FLOWRATE = K FATOR x PRESSURE 0.44 36 INHES LEARANE REQUIRED IN FRONT OF ALL UTILITY ABINET DOORS
WALL MOUNTED ORE TOTAL FLOOD PROTETION AL DETAIL IAN: 1. WIRE MAIN ONTROL PANELS PER INLUDED SHEMATIS 2. WIRE ALL FANS PER INLUDED SHEMATI 3. WIRE SHUNT TRIP BREAKER 4. WIRE UDS APPLIANE KILL, IF EQUIPPED (OPTIONAL) 5. WIRE VALVE 05/08/2013 Rev. 13 ITEM SHUNT TRIP BREAKER AL ONTRATOR REQUIREMENT ONNETION IN PANEL ONNETION IN DEVIE VOLTAGE AMPERAGE OMMENTS ST & N1 BREAKER OIL (A1 & A2) 120 VA < 4 AMPS ST TO A1 ON SHUNT BREAKER OIL, AND NEUTRAL TO A2 ON SHUNT TRIP BREAKER OIL ONTROL PANEL POWER H1 & N1 + GROUND IRUIT BREAKER 120 VA 15 AMPS ONTROL PANEL POWER MUST NOT BE RUN THROUGH SHUNT TRIP BREAKER INTERLOK 1, AR1, TR1 1, AR1, TR1 MAX 120 VA UP TO 6 AMPS SYSTEM SIGNAL, WIRE TO LIKE TERMINALS IN AL ONTROL PAKAGE UDS APPLIANE KILL (OPTIONAL) KTS & N1 KTS & N1 120 VA < 4 AMPS KILL TERMINALS MUST BE IN SERIES WITH OTHER KILL ES REMOTE ANSUL AUTOMAN (OPTIONAL) AU1, AU2 SOLENOID 120 VA < 6 AMPS 120V TO AU1, AU2 TO ANSUL AUTOMAN, ANSUL SOLENOID TO NEUTRAL VALVE 35 & N1D (IF 24 VD) & N1 (IF 120 VA) RED/RED/GREEN 24 VD OR 120 VA < 1.0 AMPS IF 24 VD - 2 WIRES & GROUND, N1D TO RED, 35 TO RED, AND GREEN TO GROUND IF 120 VA - 2 WIRES & GROUND TO RED, N1 TO RED, AND GREEN TO GROUND ONTROL PANEL POWER -2 WIRES & GROUND -120 VA, 15 AMP SERVIE -WIRE TO H1 AND N1, GROUND -POWER MUST NOT ORIGINATE FROM SHUNT TRIP BREAKER SHUNT TRIP BREAKER -2 WIRES, 120VA -ST TO A1 ON SHUNT BREAKER -NEUTRAL TO A2 ON SHUNT TRIP BREAKER SHUNT TRIP BREAKER POWER TO APPLIANE VALVE POWER -2 WIRES & GROUND -24 VD WIRE TO 35 & N1D -120 VA WIRE TO & N1 VALVE
WALL MOUNTED ORE TOTAL FLOOD PROTETION LOW-VOLTAGE DETAIL ALARM ONTRATOR: 1. WIRE REMOTE PULL STATIONS, REMOTE STATS, ORE INTERLOKS, SENSORS AND ALARM ONTATS 2. OMPLETE FINAL HOOKUP OF SYSTEM 3. PERFORM FINAL SYSTEM TEST 4. FILL SURFATANT TANK 05/08/2013 Rev. 13 ALARM ONTRATOR REQUIREMENT ITEM ONNETION IN PANEL ONNETION ON DEVIE VOLTAGE AMPERAGE OMMENTS REMOTE PULL STATION(S) 22 AND 25 21 AND 26 1 & 2 24 VD < 1.0 AMPS PULL STATION OVER N/A N/A N/A N/A REMOTE STAT SENSOR(S) 25 AND 23 26 AND 24 BLAK AND WHITE 24 VD < 1.0 AMPS ALARM ONTAT AL1, AL2 VARIES MAX 50 VA UP TO 1 AMP ORE INTERLOK(S) ILA, ILB, IL ILA, ILB, IL RS-485 OMMUNIATIONS SIGNAL WIRE PULL STATION TERMINAL 1 BETWEEN HOOD ORE PANEL TERMINALS 22 AND 25 WIRE PULL STATION TERMINAL 2 BETWEEN HOOD ORE PANEL TERMINALS 21 AND 26; USE BELDEN #6320UL OR SIMILAR WIRE PULL STATION OVER MUST BE INSTALLED IF SURFAE MOUNTED, USE OVER EXTENSION STI- 6531B WIRE SENSOR BLAK WIRES BETWEEN HOOD ORE PANEL TERMINALS 25 AND 23 WIRE SENSOR WHITE WIRE BETWEEN HOOD ORE PANEL TERMINALS 26 AND 24 HIGH TEMP (842 F) WIRE ONLY PART #W04427 (WHT) #W04427B (BLK) OR SIMILAR ALARM RELAY ONTATS FOR BUILDING ALARM LOATED IN THE ORE AL ONTROL PANEL ORE SYSTEM (1) ILA, TO ORE SYSTEM (2) ILA. ORE SYSTEM (1) ILB, TO ORE SYSTEM (2) ILB. ORE SYSTEM (1) IL, TO ORE SYSTEM (2) IL. USE BELDEN# 88760 OR SIMILAR WIRE TROUBLE ONTAT TB, TBL, TOK VARIES MAX 120 VA UP TO 6 AMPS WIRE TO TBL & TB NORMALLY OPEN ONTAT, LOSES IN TROUBLE ONDITION ORE OMMUNIATIONS ABLE RJ-45 Jack INTERNET ONNETION SIGNAL <1.0 AMPS ONNET AT5 ABLE TO LOAL AREA NETWORK WITH VALID INTERNET ONNETION ORE TOTAL FLOOD SOLENOID WS2 & N1D BLAK AND WHITE 24 VD <1.0 AMPS INTERLOK 1, AR1, TR1 1, AR1, TR1 MAX 120 VA UP TO 6 AMPS EMSPLUS ONTROL PAKAGE OR EPM03 ONTROL PAKAGE SUPERVISED LOOP -4 WIRES, 24VD ONNET BLAK WIRES BETWEEN 25 AND 23 IN PANEL, ONNET WHITE (OR RED) WIRES BETWEEN 26 AND 24 IN PANEL -ADDITIONAL STATS, WIRED IN SUPERVISED LOOP -USE HIGH TEMP (842 F) PART #W04427 (WHT) #W04427B (BLK) OR SIMILAR WIRE ONLY -SEE FIGURE 1 MBA, MBB, MB (EMSPLUS) J5 ON ORE BOARD (EPM03) MBA, MBB, MB (EMSPLUS) J3 ON EPM03 (EPM03) RS-485 OMMUNIATIONS SIGNAL ALARM ONTAT -2 WIRES WIRED TO NORMALLY OPEN ONTATS (LOSES IN ONDITION) -ORE ONTROL PANEL AL1 AND AL2 -SEE FIGURE 2 2 WIRES AND GROUND, BLAK TO WS2, WHITE TO N1D AND GREEN TO GROUND ABLE SEURED TO WATER LINE TO AVOID ONTAT WITH HOOD SURFAE SYSTEM SIGNAL, WIRE TO LIKE TERMINALS IN AL ONTROL PAKAGE 1 AND AR1 (NOT REQUIRED FOR EPM03) NETWORK ONNETIONS BETWEEN WALL MOUNT ORE AND WALL MOUNT EMSPLUS OR ONNETION BETWEEN ORE BAORD AND EPMO3 BOARD TROUBLE ONTAT -2 WIRES TO NORMALLY OPEN ONTATS (LOSE IN TROUBLE ONDITION) -ORE PANEL TERMINALS TBL AND TB -SEE FIGURE 4 ALARM PANEL APPLIANE PROTETION SOLENOID -2 WIRES AND GROUND. BLAK TO W2, WHITE TO N1D -WIRE SEURED TO WATER LINE TO AVOID ONTAT WITH HOOD -SEE FIGURE A WALL MOUNT ORE PANEL TO HOOD MOUNTED APPLIANE SOLENOID GREEN GND BLAK WS2 WHITE N1D FIELD SUPPLIED JUNTION BOX NOT ON TOP OF HOOD -USE PROVIDED ABLE ONLY -SEURE ABLE TO WATER LINE -WIRE ABLE TO FIELD SUPPLIED JUNTION BOX -WIRE FROM BOX TO REMOTE PANEL PROVIDED 8' ABLE SHIPS LOOSE APPLIANE PROTETION SOLENOID FIGURE A SOLENOID ON TOP OF HOOD WS-2 PULL STATION 10 TO 20 FEET FROM HOOD LOATED NEAR POINT OF EGRESS FROM HOOD 42 TO 48 INHES ABOVE FLOOR LEVEL TO ENTER OF HANDLE ORE OMMUNIATIONS ABLE -AT5 ABLE MUST BE INSTALLED TO A LOAL AREA NETWORK WITH VALID INTERNET AESS PULL STATION WIRES -4 WIRES, 24VD WIRE (TERMINAL 1) BETWEEN 22 AND 25 -WIRE (TERMINAL 2) BETWEEN 21 AND 26 -ADDITIONAL PULL STATIONS WIRED IN SUPERVISED LOOP -USE BELDEN #6320UL OR SIMILAR WIRE -SEE FIGURE 1 EMSPLUS OR EPM03 ONTROL OMMUNIATION -NETWORK ONNETIONS BETWEEN WALL MOUNT ORE AND WALL MOUNT EMPSLUS INTERLOK -1, AR1, TR1 ORE INTERLOK -ILA, ILB, IL -WIRED TO LIKE TERMINALS IN EAH PANEL -SEE FIGURE 3 PULL STATION PART #STI-SS2431 PROTETIVE OVER MUST BE INSTALLED
WALL MOUNTED ORE TOTAL FLOOD PROTETION LOW-VOLTAGE FIGURES 05/08/2013 Rev. 8 J2-1 J2-2 21 22 PULL STATION 1 2 STAT-1 25 26 BREAK WIRE BEFORE INSERTING INTO TERMINALS BUILDING ALARM ORE ONTROL PANEL ALARM ONTAT SHIELDED TWISTED PAIR J2-3 23 STAT-2 ALARM INPUT AL1 AL2 END OF LINE DEVIE ILA ILB BK RD BK RD ILA ILB J2-4 24 IL IL WIRING ONNETIONS FOR SUPERVISED LOOP FIGURE 1 WIRING ONNETIONS FOR ALARM ONTAT FIGURE 2 WIRING ONNETIONS FOR ORE INTERLOK FIGURE 3 BUILDING ALARM ORE ONTROL PANEL TROUBLE ONTAT PRV WATERLINE TROUBLE INPUT TOK TB TBL NO N 1 2 END OF LINE DEVIE WIRING ONNETIONS FOR TROUBLE ONTAT FIGURE 4
WALL MOUNTED ORE TOTAL FLOOD PROTETION PLUMBING DETAIL PLUMBER: 1. ONNET HOT WATER LINE; PV, OPPER OR STAINLESS STEEL PIPE ONLY 2. ONNET HOOD DRAIN(S) STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY 3. ONNET ALL END-TO-END AND BAK-TO-BAK HOOD WATER LINE ONNETIONS (PLUMBING IS FIELD SUPPLIED FOR THIS) FIELD PLUMBING MUST NOT EXEED HEIGHT OF FIELD INSTALLED VAUUM BREAKER REMOVE PLUG FROM MAIN HOOD SPRAY BAR AND ONNET TO NEXT HOOD STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY 4. PLUMB VALVE 5. INSTALL FLOOR DRAIN 6. INSTALL BAKFLOW PREVENTER IF ODE REQUIRES 05/08/2013 Rev. 13 PLUMBING ONTRATOR REQUIREMENT ITEM ONNETION TEMPERATURE PRESSURE FLOW RATE OMMENTS HOT WATER LINE 3/4, 1, OR 1-1/2 INH NPT 140 to 170 F 30 TO 70 PSI 0.7 GPM PER FOOT OF HOOD INSULATE HOT WATER PIPE, MINIMUM PRESSURE DEPENDANT ON LENGTH OF HOOD SYSTEM HOOD DRAIN(S) 1-1/2 INH NPT N/A GRAVITY DRAIN 0.7 GPM PER FOOT OF HOOD 2 DRAINS ON 24 INH TALL HOODS WITH 20 INH TALL FILTERS AND HOODS 10 FEET AND LONGER END-TO-END ORE ONNETION 3/4 INH NPT N/A N/A N/A ONNET WITH NPT PIPE, SEAL ALL THREADS, HOOD ONNETION PROVIDED, FIELD PIPING MUST REMAIN BELOW HEIGHT OF VAUUM BREAKER BAK-TO-BAK ORE ONNETION 3/4 INH NPT N/A N/A N/A ONNET WITH NPT PIPE, SEAL ALL THREADS, HOOD ONNETION PROVIDED VALVE VARIES N/A SEE HART N/A UP TO 2 INHES NPT WITH 24V ONTROLS, 2-1/2 AND 3 INH USE 120V ONTROL FLOOR DRAIN(S) 1-1/2 INH N/A GRAVITY DRAIN N/A USED TO HELP LEAN UP SYSTEM DISHARGE SURFATANT LINE BAKFLOW PREVENTER DRAIN LINE (OPTIONAL) 1/4 INH OD TUBING N/A 70 PSI N/A SURFATANT LINE MUST NOT BE IN ONTAT WITH THE HOOD SURFAE INLET + DRAIN N/A VARIES N/A INSTALLED WHEN PAKAGE HAS A BAKFLOW PREVENTER VALVE, SEE BAKFLOW PREVENTER VALVE MANUAL FOR DETAILS HOT WATER LINE -PV, OPPER, OR STAINLESS STEEL PIPE ONLY -140-170 F OPERATING TEMPERATURE -30 TO 70 PSI OPERATING PRESSURE -125 PSI MAX STATI PRESSURE -0.7 GPM PER FOOT OF HOOD -3/4, 1, OR 1-1/2 INH NPT FITTING, INSULATED HOOD WATER LINE -30 TO 70 PSI OPERATING PRESSURE, SIZED TO MATH PRESSURE DROP BETWEEN WALL MOUNT PAKAGE AND HOOD -DEDIATED LINE WITH NO MANUAL UNSUPERVISED SHUT-OFF VALVE -SURFATANT INJETION INSTALLED AFTER FIELD INSTALLED VAUUM BREAKER -VAUUM BREAKER INSTALLED AT HIGHEST POINT BETWEEN PAKAGE AND HOOD -STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY END-TO-END OR BAK-TO-BAK ONNETION -INSTALLED AND PROVIDED BY PLUMBER STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY -FIELD PIPING MUST REMAIN BELOW HEIGHT OF VAUUM BREAKER SURFATANT LINE -1/4" OD TUBING ONNETING SURFATANT PUMP WITH INJETION POINT ON HOOD -LINE MUST NOT OME IN ONTAT WITH THE HOOD SURFAE HOOD DRAIN(S) -1-1/2 INH NPT ONNETED TO BUILDING GREASE TRAP -2 DRAINS ON 24 INH TALL HOODS WITH 20 INH FILTERS -2 DRAINS ON HOODS 10 FEET AND LONGER -STAINLESS STEEL, OPPER OR STEEL PIPE ONLY BAKFLOW PREVENTER DRAIN -IF BFP IS INSTALLED, ADDITIONAL DRAIN MUST BE INSTALLED BY PLUMBER -SEE BFP MANUAL FOR DETAILS SIZE MAX INLET PRESSURE VOLTAGE BTU/HR FLOOR DRAIN -1-1/2 DRAIN INSTALLED IN FLOOR, NEAR APPLIANES -FLOOR DRAINS MAY BE USED TO DRAIN HOOD 3/4" 25 24VD 247,500 1" 25 24VD 1,119,000 1-1/4" 25 24VD 1,730,000 1-1/2" 25 24VD 1,900,000 2" 15 24VD 3,251,000 VALVE 2-1/2" 5 120VA 5,821,000 3" 5 120VA 7,430,000 VALVE -THREADED NPT ONNETION -SEE TABLE ABOVE MAX PRESSURE
WALL MOUNTED ORE TOTAL FLOOD PROTETION SPRINKLER DETAIL 05/08/2013 Rev. 13 BUILDING SPRINKLER ONTRATOR: 1. ONNET ORE WATER LINE TO BUILDING WET SPRINKLER SYSTEM. STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY SPRINKLER ONTRATOR REQUIREMENT ITEM ONNETION OPERATING PRESSURE K-FATOR FLOW RATE OMMENTS ORE WATER SUPPLY LINE 3/4,1, OR 1-1/2 INH NPT 30 PSI TO 70 PSI SEE TABLE 1.5 GPM PER FOOT OF HOOD WATER LINE MUST BE SUPERVISED AND HAVE NO UNSUPERVISED MANUAL SHUT-OFF VALVES MINIMUM PRESSURE AND FLOWRATE DEPENDENT ON LENGTH OF HOOD SYSTEM MINIMUM OPERATING PRESSURE REQUIREMENTS ORE WATER SUPPLY LINE -30 PSI TO 70 PSI OPERATING PRESSURE -125 PSI MAX STATI PRESSURE, 3/4, 1, 1-1/2 INH NPT FITTING, 1.5 GPM PER FOOT OF HOOD -ONNETED TO SUPERVISED, DEDIATED LINE WITH NO UNSPUERVISED MANUAL SHUT-OFF VALVES -ONNET TO BUILDING SPRINKLER WATER LINE (REDUE PRESSURE) WHEN REQUIRED -STAINLESS STEEL, OPPER, OR STEEL PIPE ONLY LENGHT OF HOOD (FT) MINIMUM INLET WATER PRESSURE FOR SELF LEANING (PSI) MINIMUM INLET WATER PRESSURE FOR ORE PROTETION (PSI) DISHARGE OEFFIIENTS (K-FATOR) 4 30 30 1.3 8 30 30 2.6 12 30 30 4.0 16 30 30 5.3 20 31 33 6.4 24 32 36 7.4 28 34 39 8.3 32 37 44 9.0 36 39 49 9.7 40 42 56 10.2 44 46 63 10.6 48 50 70 11.1 TOTAL FLOWRATE = K FATOR x PRESSURE 0.44
24V ORE BASI OPERATING INSTRUTIONS ORE PROTETION SYSTEM THE DAILY BASI OPERATION OF THE ORE PROTETION SYSTEM IS IDENTIAL TO THE SELF LEANING HOOD. IN THE EVENT OF A HOOD, ORE PROTETION IS ATIVATED. IF THE HOOD STAT INSTALLED IN THE RISER SENSES A TEMPERATURE HOTTER THEN ITS INTERNAL SET POINT OR IF THE REMOTE MANUAL PULL STATION IS PULLED THE SYSTEM IS ATIVATED. AN WATER SOLENOID IS ENERGIZED ALLOWING THE FLOW OF WATER TO THE HOOD DUT AND PLENUM THROUGH THE SELF LEANING HOOD SPRAY BAR. AT THE SAME TIME A SEOND WATER SOLENOID IS ENERGIZED AND ALLOWS THE FLOW OF WATER TO THE APPLIANES. SURFATANT IS ONTINUALLY INJETED INTO THE WATER STREAM TO HELP SUPPRESS THE. ONE THE SYSTEM IS ATIVATED, A SYSTEM ATIVATED LIGHT IS ILLUMINATED ON THE HOOD ONTROL PANEL AND AN AUDIBLE ALARM SOUNDS. ALL AND APPLIANES UNDER THE HOOD MUST BE ALLY INTERLOKED TO SHUT OFF. THIS IS AHIEVED VIA A VALVE RELAY AND/OR A SHUNT TRIP BREAKER. A TIMER IS ALSO ENERGIZED UPON SYSTEM ATIVATION. THE TIMER IS SET FOR 30 MINUTES AND KEEPS THE WATER SPRAY SYSTEM RUNNING FOR A MINIMUM OF 30 MINUTES. THIS IS NEESSARY TO HELP EXTINGUISH ALL REMAINING DUT POTENTIAL. THE SYSTEM IS ALLY OPERATED AND THUS REQUIRES A BATTERY BAKUP SYSTEM. IN THE EVENT OF A LOSS OF AL POWER, ALL AND APPLIANES UNDER THE HOOD MUST BE ALLY INTERLOKED TO SHUT OFF. THIS IS AHIEVED VIA A VALVE RELAY AND/OR A SHUNT TRIP BREAKER. THE BATTERY BAKUP WILL AUTOMATIALLY ENERGIZE UPON A LOSS OF POWER. THE BATTERY BAKUP WILL MONITOR THE SYSTEM IRUIT FOR ONE DAY AND BE ABLE TO OPERATE THE SYSTEM IRUIT FOR A MINIMUM OF 30 MINUTES. ONE POWER IS RESTORED, THE BATTERY WILL AUTOMATIALLY REHARGE. ORE PROTETION RESET OVERVIEW ORE APPLIATION SPEIFI DETAILS SELF LEANING HOODS SELF LEANING HOOD OPTION IS REQUIRED TO APPLY ORE PROTETION. HIGH EFFIIENY, HIGH VELOITY ARTRIDGE, SOLO, OR OMBO FILTERS ARE REQUIRED. IF SUBSTITUTE FILTERS ARE UTILIZED, PRODUT WARRANTY IS VOID AND THERE IS NO GUARANTEE IN PERFORMANE. SOLID FUEL APPLIANES SOLID FUEL APPLIANES PRODUE SPARKS THAT AN TRAVEL INTO DUTWORK. THESE APPLIANES REQUIRE SOLO FILTERS AND AN ADDITIONAL STAT AT THE DUT DISHARGE NEAR THE FAN IF THE DUTWORK EXEEDS 10 FEET IN LENGTH OR ONTAINS HORIZONTAL DUT RUNS. INDIATE ON DUTWORK DRAWING WHERE STAT IS TO BE INSTALLED WITH QUIK SEAL. ALL ADDITIONAL STATS ARE WIRED INTO THE SUPERVISED LOOP WITH THE FIRST STAT. DUT SHOULD BE INSULATED PER ODE REQUIREMENTS. IF SUBSTITUTE FILTERS ARE UTILIZED, PRODUT WARRANTY IS VOID AND THERE IS NO GUARANTEE IN PERFORMANE. SELF LEANING HOODS AND ETL LISTED DUTWORK ARE ALSO REQUIRED. DUT STATS A STAT MUST BE INSTALLED AT 50 FEET INTERVALS WHEN THE DUT LENGTH EXEEDS 50 FEET. IMPORTANT: ANY DEVIATION FROM ANY OF THE MANUFATURER'S REOMMENDATIONS IN THIS DOUMENT OR THE OPERATION AND INSTALLATION MANUAL MUST BE APPROVED BY THE OWNER OF THIS EQUIPMENT AND VOIDS THE WARRANTY AND PERFORMANE GUARANTEE OF THIS PRODUT. 05/08/2013 Rev. 2 THERE ARE MULTIPLE ATIONS REQUIRED TO RESET THE SYSTEM. FIRST, THE DUT STAT MUST BE OOLED TO BELOW ITS INTERNAL SET POINT AND THE REMOTE PULL STATION MUST BE RESET USING A STANDARD ALLEN WRENH KEY. ONE BOTH OF THESE DEVIES HAVE BEEN RESET, THE TIMER WILL AUTOMATIALLY STOP THE SYSTEM ONE ITS TIME DURATION HAS ENDED. AN ALTERNATIVE METHOD TO BYPASSING THE TIMER IS TO PRESS THE SYSTEM RESET BUTTON ON THE FAE OF THE ORE ONTROL ABINET. THIS WILL DE-ENERGIZE THE TIMER AND RESET THE SYSTEM. NOTE: THE STAT MUST BE OOL AND THE REMOTE PULL STATION MUST BE RESET FOR THIS BUTTON TO WORK. THE SYSTEM MUST BE FILLED WITH SURFATANT AND NOZZLE APS MUST BE REINSTALLED. AFTER A, FULL INSPETION BY A ERTIFIED PROFESSIONAL MUST BE ONDUTED PRIOR TO RESTARTING THE SYSTEM.
24V SUPERVISED LOOP INSTRUTIONS 6/29/2012 Rev. 3 J2-1 J2-2 21 22 25 PULL STATION 1 2 STAT-1 26 BREAK WIRE BEFORE INSERTING INTO TERMINALS SUPERVISED LOOP INSTALLATION -LOOP MUST BE ONTINUOUS BETWEEN THE STATS AND PULL STATIONS, QUANTITY OF EAH OMPONENTS MAY VARY, -POLLUTION ONTROL UNIT MAY NOT HAVE A PULL STATION INSTALLED; IN THIS ASE, INSTALL A JUMPER BETWEEN TERMINALS 21 AND 26, AS WELL AS TERMINALS 22 AND 25 -MULTIPLE PULL STATIONS AND SENSORS AN BE USED ON EAH PANEL, WHEN INSTALLED, THEY ARE WIRED IN A DAISY-HAIN STYLE AS SHOWN STAT-2 J2-3 23 J2-4 24 ONNETION BETWEEN MULTIPLE ORE SYSTEMS -THERE IS AN RS-485 ONNETION IN EAH ORE PANEL; TO ONNET MULTIPLE ORE PANELS, SIMPLY ONNET MATHING TERMINALS FROM ONE PANEL TO THE NEXT IN SERIES -USE BELDEN #88760 OR SIMILAR WIRE, SHIELDED, SINGLE TWISTED PAIR ILA ILB IL BK RD SHIELDED TWISTED PAIR BK RD ILA ILB IL RS 485 INTERLOK NETWORK
PRESSURE REDUING VALVE WITH AND PRESSURE MONITORING VALVE -THE PRESSURE REDUING VALVE MUST BE INSTALLED WITH AN APPROVED - PART NUMBERS AND SUPPORT BRAKETS ARE LISTED IN THE TABLE - OMES WITH TWO SINGLE POLE, DOUBLE THROW ES - MUST BE ATTAHED PER PRESSURE REDUTION VALVE BRAKET INSTRUTIONS 05/07/2013 REV. 5 VALVE BRAKET -VALVE BRAKET ONTAINS NEESSARY PARTS AND INSTRUTIONS TO ADAPT THE TO THE VALVE. PRESSURE REDUING VALVE -VALVE IS AVAILABLE IN 1-1/2" NPT ONNETIONS -PRESSURE REDUING VALVE MUST BE INSTALLED BEFORE THE ORE PROTETION PAKAGE TO REDUE SPRINKLER LINE INOMING PRESSURE AND VOLUME -PRESSURE REDUTION IS BASED UPON THE INOMING PRESSURE AND VOLUME -SEE TABLE FOROUTLET PRESSURE PRESSURE MONITORING - IS AVAILABLE WITH A 1/2" NPT ONNETION -PRESSURE MONITORING VALVE OMES WITH TWO SINGLE POLE, DOUBLE THROW ES, EAH WITH AN ADJUSTABLE SETPOINT -SETPOINT AN BE BETWEEN 10 AND 60 PSI -PART NUMBER PL-PS402 OMPLETE PARTS KIT UR-20 VALVE OUTLET PRESSURE PERENTAGE BRAKET UR-20-W KIT UR-20-W 28.7% PL-PVS2 80574001 UR-20-X KIT UR-20-X 33.8% PL-PVS2 80574001 UR-20-Z KIT UR-20-Z 56.5% PL-PVS2 80574001 OUTLET PRESSURE (PSI) INOMING PRESSURE (PSI) UR-20 VALVE 50 60 70 80 90 100 110 120 130 140 150 160 170 UR-20-W 14.35 17.22 20.09 22.96 25.83 28.7 31.57 34.44 37.31 40.18 43.05 45.92 48.79 UR-20-X 16.9 20.28 23.66 27.04 30.42 33.8 37.18 40.56 43.94 47.32 50.7 54.08 57.46 UR-20-Z 28.25 33.9 39.55 45.2 50.85 56.5 62.15 67.8 73.45 79.1 84.75 90.4 96.05 THE ORE PANEL ONTAINS TWO ISOLATED INPUTS FOR AUXILIARY OF PRESSURE REDUING VALVES AND PRESSURE ES. EAH DEVIE ABOVE HAS TWO SINGLE POLE, DOUBLE THROW ES. THESE ES MAY BE WIRED IN PARALLEL TO THE ORE PANEL TERMINALS H1D AND 39. WHEN A FAULT IS DETETED, THE ORE BOARD WILL SHUT DOWN THE VALVE AND SHUNT TRIP, TRIGGER A LOAL TROUBLE SIGNAL, AND ALERT ALL ATTAHED ORE PAKAGES. ALTERNATIVELY, THE ES FROM EAH DEVIE OULD BE ONNETED TO THE TROUBLE INPUT OF THE BUILDING ALARM PANEL TO INDIATE A TROUBLE ONDITION. BOTH METHODS ARE SHOWN BELOW. WIRING ONNETIONS FOR TROUBLE ONTAT H1D 38 ORE ONTROL ONNETIONS PRV N WATER PRESSURE 2 39 N1D BUILDING ALARM TROUBLE INPUT TOK ORE ONTROL PANEL TROUBLE ONTAT TB TBL PRV NO N WATERLINE 1 2 END OF LINE DEVIE